BTR-5601MG

Optoway BTR-5601MG / BTR-5601AMG FEATURES DESCRIPTION BTR-5601MG 1 *********************************************************************************************************************************************************************** 1310 nm TX / 1550 nm RX , 3.3V / 622 Mbps RoHS Compliant Single-Fiber MM Transceiver ********************************************************************************************************************************************************************** l l l l l l l l l l l l l Single Fiber Bi-Directional MM Transceiver 1310 nm LD Transmitter 1550 nm Receiver D istance0 to 1000 m Industry Standard 1 x 9 Footprint Single +3.3 V Power Supply RoHS Compliant Speed up to 650 Mb/s 0 to 70oC Operating : BTR-5601MG -20 to 85oC Operating : BTR-5601AMG PECL Differential Inputs and Outputs Wave Solderable and Aqueous Washable Class 1 Laser International Safety Standard IEC-60825 Compliant The BTR-5601MG series is high performance module for multi-mode single fiber communications by using 1310 nm transmitter and 1550 nm receiver. The transmitter section uses a multiple quantum well laser and is a class 1 laser compliant according to International Safety Standard IEC-60825. The receiver section uses an integrated 1550 nm detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC. A PECL logic interface simplifies interface to external circuitry. LASER SAFETY This multi-mode transceiver is a Class 1 laser product. It complies with IEC-60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug. APPLICATIONS l WDM 622 Mb/s Links l SONET/SDH Equipment Interconnect ORDER INFORMATION P/No. Bit Rate (Mb/s) 622 622 D istance (m) 0 to 1000 0 to 1000 TX (nm) 1310 1310 RX (nm) 1550 1550 Voltage (V) 3.3 3.3 Package TX RX Sens. R oHS Power (dBm) Compliant (dBm) 0 to 70 -8 to -15 -26 Yes -20 to 85 -8 to -15 -26 Yes Temp (oC) BTR-5601MG BTR-5601AMG 1X9 SC 1X9 SC Absolute Maximum Ratings Parameter Storage Temperature Operating Temperature Soldering Temperature Power Supply Voltage Input Voltage Output Current Symbol Tstg Topr --Vcc --Iout Min -40 0 -20 0 GND 0 Max 85 70 85 250 4.5 Vcc 30 Units o C o C o Notes BTR-5601MG BTR-5601AMG 10 seconds on leads only C V V mA Recommended Operating Conditions Parameter Power Supply Voltage Operating Temperature Data Rate Power Supply Current Symbol Vcc Topr Min 3.13 0 -20 Typ 3.3 Max 3.47 70 85 650 260 Units V o C / BTR-5601MG o C / BTR-5601AMG Mb/s mA 622 Icc *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw http: // www.optoway.com.tw 10/1/2005 V3.0 Optoway Transmitter Specifications (0 oC < Topr < 70 oC, 3.13V < Vcc < 3.47V) Parameter Optical Optical Transmit Power Output Center Wavelength Output Spectrum Width Extinction Ratio Optical Rise Time Optical Fall Time Relative Intensity Noise Total Jitter Electrical Data Input Current – Low Data Input Current – High Differential Input Voltage Data Input Voltage – Low Data Input Voltage -- High Symbol Po λ ∆λ ER tr tf RIN TJ IIL IIH VIH - VIL VIL - VCC V IH - VCC Min -15 1260 --8.2 Typ --1310 ----Max -8 1360 5 --1.2 1.2 -116 0.55 Units dBm nm nm dB ns ns dB/Hz ns µA µA mV V V BTR-5601MG Notes 1 RMS (σ) 10% to 90% Values 10% to 90% Values 2 2 *********************************************************************************************************************************************************************** -350 350 300 -2.0 -1.1 -1.58 -0.74 3 3 Notes: 1. Output power is power coupled into a 62.5/125 µm multi-mode fiber. 2. Measured with a 223-1 PRBS with 72 ones and 72 zeros. 3. These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs. Receiver Specifications (0oC < Topr < 70oC, 3.13 V < Vcc < 3.47V) Parameter Optical Sensitivity Maximum Input Power Signal Detect -- Asserted Signal Detect -- Deasserted Signal detect -- Hysteresis Wavelength of Operation Electrical Data Output Voltage – Low Data Output Voltage – High SD Output Voltage -- Low SD Output Voltage -- High Symbol --Pin Pa Pd Min ---8 ---40 1.0 1480 -2.0 -1.1 -2.0 -1.1 Typ ----------Max -26 ---26 --1600 -1.58 -0.74 -1.58 -0.74 Units dBm dBm dBm dBm dB nm V V V V Notes 1 Transition: low to high Transition: high to low 2 3 3 3 3 V OL - VCC V OH - VCC V OL - VCC V OH - VCC Notes: 1.Minimum sensitivity and saturation levels at BER 1E-=10 for a 223-1 PRBS. 2. At least 30 dB optical isolation for the wavelength 1260 to 1360 nm. 3. These inputs are compatible with 10K, 10KH and 100K ECL and PECL outputs. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw http: // www.optoway.com.tw 1 0/1/2005 V3.0 Optoway CONNECTION DIAGRAM Receiver Signal Ground 1 (Rx GND) Receiver Data Out 2 (RD+) Receiver Data Out Bar 3 (RD−) Signal Detect 4 (SD) Receiver Power Supply 5 (Rx Vcc) Transmitter Power Supply 6 (Tx Vcc) Transmitter Data In Bar 7 (TD− ) Transmitter Data In 8 (TD+) Transmitter Signal Ground 9 (Tx GND) N/C BTR-5601MG 3 *********************************************************************************************************************************************************************** TOP VIEW N/C P IN 1 2 3 4 5 6 7 8 9 Symbol Rx GND RD+ RD− SD R x Vcc T x Vcc TD− TD+ Tx GND Notes Directly connect this pin to the receiver ground plane See recommended circuit schematic See recommended circuit schematic Active high on this indicates a received optical signal +3.3V dc power for the receiver section +3.3V dc power for the transmitter section See recommended circuit schematic See recommended circuit schematic Directly connect this plan to the trransmitter ground plane RECOMMENDED CIRCUIT SCHEMATIC The split-load terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc and Tx Vcc. A GND plane under the module is required for good EMI and sensitivity performance. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw http: // www.optoway.com.tw 1 0/1/2005 V3.0 Optoway PACKAGE DIAGRAM Units in mm BTR-5601MG 4 *********************************************************************************************************************************************************************** Note: Specifications subject to change without notice. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw http: // www.optoway.com.tw 1 0/1/2005 V3.0