BTRS-7700MG_09

Optoway FEATURES l l l l l l l l l l l l l l l BTRS-7700MG 1 *********************************************************************************************************************************************************************** BTRS-7700MG / BTRS-7700CMG / BTRS-7700AMG / BTRS-7700ACMG 1550 nm TX / 1310 nm RX , 3.3V / 1250 Mbps RoHS Compliant Single-Fiber MM Transceiver ********************************************************************************************************************************************************************** DESCRIPTION Single Fiber Bi-Directional MMTransceiver 1550 nm Transmitter 1310 nm Receiver D istance 0 to 500 m 0 to 70oC Operating: BTRS-7700MG -20 to 85oC Operating: BTRS-7700AMG Speed up to 1300 Mbps 2 x5 Package with SC Receptacle LVTTL Signal Detect Output : BTRS-7700CMG LVPECL Signal Detect Output : BTRS-7700MG Single +3.3 V Power Supply RoHS Compliant PECL Differential Inputs and Outputs Wave Solderable and Aqueous Washable Class 1 Laser International Safety Standard IEC-60825 Compliant The BTRS-7700MG series is high performance module for multi-mode single fiber communications by using 1550 nm transmitter and 1310 nm receiver. The transmitter section uses a multiple quantum well laser and is a class 1 laser compliant according to International Safety Standard IEC-60825. The receiver section uses an integrated 1310 nm detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC. A PECL logic interface simplifies interface to external circuitry. LV-TTL Signal Detect is used. LASER SAFETY This multi-mode transceiver is a Class 1 laser product. It complies with IEC-60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug. APPLICATIONS l WDM Gigabit Ethernet Links l SONET/SDH Equipment Interconnect l Fiber Channel Links ORDER INFORMATION P /No. Bit Rate D istance (Gb/s) (m) 1.25 1.25 0 to 500 0 to 500 TX (nm) 1550 1550 RX (nm) 1310 1310 Voltage (V) 3.3 3.3 Package Temp (oC) 0 to 70 -20 to 85 TX RX Sens. RoHS Power (dBm) Compliant (dBm) -4 to -10 -17 Yes -4 to -10 -17 Yes BTRS-7700MG BTRS-7700AMG SC, 2X5 SC, 2X5 Absolute Maximum Ratings Parameter Storage Temperature Operating Temperature Soldering Temperature Power Supply Voltage Input Voltage Output Current Symbol Tstg Topr --Vcc --Iout Min -40 0 -20 0 GND 0 Max 85 70 85 260 3.6 Vcc 30 Units o C o C o Notes BTRS-7700MG BTRS-7700AMG 10 seconds on leads only C V V mA Recommended Operating Conditions Parameter Power Supply Voltage Operating Temperature Data Rate Power Supply Current Symbol Vcc Topr Min 3.13 0 -20 Typ 3.3 Max 3.47 70 85 1300 260 Units / Notes V o C / BTRS-7700MG o C / BTRS-7700AMG Mb/s mA 1250 Icc *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw http: // www.optoway.com.tw 10/1/2009 V3.0 Optoway Transmitter Specifications (0oC < Topr < 70oC, 3.13V < Vcc < 3. 47V) Parameter Optical O ptical Transmit Power Output Center Wavelength Output Spectrum Width Output Eye O ptical Rise Time O ptical Fall Time R elative Intensity Noise T otal Jitter E lectrical D ata Input Current – Low D ata Input Current – High D ifferential Input Voltage D ata Input Voltage – Low D ata Input Voltage -- High D isable Input Voltage -- Low D isable Input Voltage -- High Shut Off Time for TxDis Symbol Min Typ Max -4 1580 4 0.26 0.26 -120 0.227 Units dBm nm nm ns ns dB/Hz ns µA µA mV V V V V ms Po -10 1480 λ σλ Compliant with IEEE 802.3z tr tf RIN TJ IIL IIH VIH - VIL VIL - VCC VIH - VCC V TDIS,L V TDIS,H tDIS -350 300 -2.0 -1.1 0 Vcc – 1 .3 350 1600 -1.58 -0.74 0 .8 Vcc 1 BTRS-7700MG Notes 1 RMS (σ) 20% to 80% Values 20% to 80% Values 2 2 ********************************************************************************************************************************************************************** 3 3 TX Output Enabled TX Ouput Disabled N otes: 1. Output power is power coupled into a 62.5/125 µm multi-mode fiber. 2. Measured with a 27-1 PRBS. 3. These inputs are compatible with 10K, 10KH and 100K ECL and LVPECL inputs. Receiver Specifications (0oC < Topr < 70oC, 3.13 V < Vcc < 3. 47V) Parameter Optical Sensitivity Maximum Input Power Signal Detect -- Asserted Signal Detect -- Deasserted Signal detect -- Hysteresis Wavelength of Operation O ptical Return Loss E lectrical D ata Output Voltage Swing SD Output Voltage -- Low SD Output Voltage -- High SD Output Voltage -- Low SD Output Voltage -- High Signal Detect Assert Time Signal Detect Deassert Time Symbol --Pin Pa Pd Min ---3 ---31 1.0 1260 20 0.575 -2.0 -1.1 0 2.0 Typ ----------Max -17 ---17 --1360 Units dBm dBm dBm dBm dB nm dB V V V V V µs µs Notes 1 Transition: low to high Transition: high to low 2 ORL V OH – VOL VOL - VCC VOH - VCC VOL VOH ASMAX ANSMAX 0.930 -1.58 -0.74 0.8 Vcc+0.3 100 300 BTRS-7700MG BTRS-7700CMG OFF to ON ON to OFF N otes: 1. Minimum sensitivity and saturation levels at BER 1E-12 for a 27-1 PRBS. 2. At least 30 dB optical isolation for the wavelength 1480 to 1580 nm. ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. N o.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 E-mail: sales@optoway.com.tw Fax: 886-3-5979737 h ttp: // www.optoway.com.tw 10/1/2009 V3.0 Optoway CONNECTION DIAGRAM BTRS-7700MG 3 ********************************************************************************************************************************************************************** P IN 1 2 3 4 5 6 7 8 9 10 MS Symbol VEEr VCC r SD RD− RD+ VCC t VEEt TxDis TD+ TDMS Notes Directly connect this pin to the receiver ground plane +3.3V dc power for the receiver section Active high on this indicates a received optical signal. R eceiver Dataout Bar. See recommended circuit schematic Receiver Dataout. See recommended circuit schematic +3.3V dc power for the transmitter section Directly connect this plan to the transmitter ground plane Transmitter Disable. Connect this pin to +3.3V TTL logic “1 ” to disable module To enable module connect to TTL logic low “0” Transmitter Data In. See recommended circuit schematic Transmitter Data In Bar. See recommended circuit schematic Mounting Studs. Connect to Chassis Ground RECOMMENDED CIRCUIT SCHEMATIC depend on customer's PHY terminate and bias inside Transceiver module TDZ=50R LVPECL Vcc3.3V TD+ Z=5OR 130R 10 9 8 7 6 TXDis(LVTTL) 130R 1uH Vcc3.3V TDTD+ TDis Veet Vcct 10nF 10uF 1uH 10nF 10uF PHY DEVICE BTRS-7XXXC 1 2 3 4 5 10nF 10uF Vcc3.3V Veer Vccr SD RDRD+ RD+ 100R Z=50R LVPECL RDZ=5OR depend on customer's PHY SD TO LVTTL STAGE ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw http: // www.optoway.com.tw 10/1/2009 V3.0 Optoway PACKAGE DIAGRAM Units in mm BTRS-7700MG 4 ********************************************************************************************************************************************************************** N ote: Specifications subject to change without notice. ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. N o.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 E-mail: sales@optoway.com.tw Fax: 886-3-5979737 h ttp: // www.optoway.com.tw 10/1/2009 V3.0