SPB-7810G

Optoway SPB-7810G / SPB-7810BG / SPB-7810LG / SPB-7810BLG (RoHS Compliant) FEATURES l l l l l l l l l l l l l SPB-7810G 1 *********************************************************************************************************************************************************************** 1310 nm TX / 1490 nm RX , 3.3V / 1250 Mbps Single-Fiber SFP Transceiver ********************************************************************************************************************************************************************** DESCRIPTION 1 -Fiber Bi-Directional SFP Optical Transceiver Compliant with IEEE 802.3ah-2004 1000BASE-BX Simplex SC Connector: SPB-7810G Simplex LC Connector: SPB-7810LG 1310 nm LD Transmitter 1490 nm Receiver D istance Up to 10 km AC/AC Coupling according to MSA Single +3.3 V Power Supply RoHS Compliant 0 to 70oC Operating: SPB-7810G -10 to 85oC Operating: SPB-7810BG Class 1 Laser International Safety Standard IEC 60825 Compliant The SPB-7810G series is small form factor pluggable module for Gigabit Ethernet 1000BASE-BX and Fibre Channel single fiber communications by using 1310 nm transmitter and 1490 nm receiver. It is with the SFP 20-pin connector to allow hot plug capability. The transmitter section uses a multiple quantum well 1310 nm laser and is a class 1 laser compliant according to International Safety Standard IEC 60825. The receiver section uses an integrated 1490 nm detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC. LASER SAFETY This single mode transceiver is a Class 1 laser product. It complies with IEC 60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug. APPLICATIONS l WDM Gigabit Ethernet Links l SONET/SDH Equipment Interconnect l Fibre Channel Links ORDER INFORMATION P/No. SPB-7810G SPB-7810BG SPB-7810LG SPB-7810BLG Bit Rate (Gb/s) 1.25 1.25 1.25 1.25 Distance (km) 10 10 10 10 TX (nm) 1310 1310 1310 1310 RX (nm) 1490 1490 1490 1490 Package SC SFP SC SFP LC SFP LC SFP Temp TX Power (oC) (dBm) 0 to 70 -3 to -9 -10 to 85 -3 to -9 0 to 70 -3 to -9 -10 to 85 -3 to -9 RX Sens. (dBm) -20 -20 -20 -20 RoHS Compliant Yes Yes Yes Yes ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw http: // www.optoway.com.tw 3 /1/2006 V3.0 Optoway Absolute Maximum Ratings Parameter Storage Temperature Operating Case Temperature Relative Humidity Power Supply Voltage Input Voltage Output Current Symbol Tstg Topr RH Vcc --Iout Min -40 0 -10 0 0 GND 0 Max 85 70 85 85 3.6 Vcc 30 Units o C o C % V V mA SPB-7810G Notes SPB-7810G SPB-7810BG Non condensing 2 *********************************************************************************************************************************************************************** Recommended Operating Conditions Parameter Power Supply Voltage Power Supply Current Operating Case Temperature Data Rate Symbol Vcc ICC (TX+RX) Topr Min 3.1 0 -10 1250 Typ 3.3 200 Max 3.5 300 70 85 1300 Units / Notes V mA o C / SPB-7810G o C / SPB-7810BG Mb/s Transmitter Specifications (0 oC < Topr < 70 oC, 3.1V < Vcc < 3. 5V) Parameter Symbol Min Optical Optical Transmit Power Po -9 Output Center Wavelength 1260 λ Output Spectrum Width σλ Extinction Ratio ER 9 Output Eye Compliant with IEEE 802.3z Optical Rise Time tr Optical Fall Time tf Relative Intensity Noise RIN Total Jitter TJ Electrical Data Input Current – Low IIL -350 Data Input Current – High IIH Differential Input Voltage VIH - VIL 0.5 TX Disable Input Voltage – Low TDIS, L 0 TX Disable Input Voltage – High TDIS, H 2.0 TX Disable Assert Time TASSERT TX Disable Deassert Time T DEASSERT TX Fault Output Voltage -- Low TFaultL 0 TX Fault Output Voltage -- High TFaultH 2.0 Typ Max -3 1360 2.5 Units dBm nm nm dB ns ns dB/Hz ns µA µA V V V µs ms V V Notes 1 RMS (σ) 1310 0.26 0.26 -120 0.227 20% to 80% Values 20% to 80% Values 2 350 2.4 0.5 Vcc 10 1 0.5 Vcc+0.3 Peak-to-Peak 3 3 4 4 Notes: 1. Output power is power coupled into a 9/125 µm single mode fiber. 2. Measured with a 27-1 PRBS. 3. There is an internal 4.7K to 10K ohm pull-up resistor to VccTX. 4. Open collector compatible, 4.7K to 10K ohm pull-up to Vcc (Host Supply Voltage). ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw http: // www.optoway.com.tw 3/1/2006 V3.0 Optoway Receiver Specifications (0oC < Topr < 70oC, 3.1 V < Vcc < 3. 5V) Parameter Optical Sensitivity Maximum Input Power Signal Detect -- Asserted Signal Detect -- Deasserted Signal detect -- Hysteresis Wavelength of Operation Optical Return Loss Electrical Differential Output Voltage Output LOS Voltage -- Low Output LOS Voltage – High Signal Detect Assert Time Signal Detect Deassert Time Symbol --Pin Pa Pd Min ---3 ---31 1.0 1480 14 0.6 0 2.0 Typ ----------Max -20 ---20 --1500 Units dBm dBm dBm dBm dB nm dB V V V µs µs SPB-7810G Notes 5 Transition: low to high Transition: high to low 6 3 *********************************************************************************************************************************************************************** ORL VOH – VOL VOL V OH ASMAX ANSMAX 2.0 0.5 Vcc+0.3 100 300 7 7 OFF to ON ON to OFF Notes: 5. Minimum sensitivity and saturation levels at BER 1E-12 for a 27-1 PRBS. 6. At least 30 dB optical isolation for the wavelength 1260 to 1360 nm. 7. Open collector compatible, 4.7K to 10K ohm pull-up to Vcc (Host Supply Voltage). RECOMMENDED CIRCUIT SCHEMATIC VeeT Tx_DISABLE T x_FAULT (1,17,20) 3 2 4.7K to 10KΩ TD + 18 Z=50Ω TD 19 Z=50Ω VccT 16 10nF 1μH Vcc 3.3V 10μF 10nF 1μH VccR 15 10nF 10μF 10μF TD TD + Tx_DISABLE Tx_FAULT LD Driver 100Ω SerDes IC Protocol IC RD - 12 Z=50Ω 100Ω RD - POST Amp RD + 13 Z=50Ω 4.7K to 10KΩ RD + depending on SERDES LOSS OF SINGAL LOS VeeR MOD_DEF(0) 8 (9,10,11,14) 6 5 4 4.7K to 10KΩ 4.7K to 10KΩ 4.7K to 10KΩ Vcc 3.3V MODULE DETECT SCL SDA EEPROM MOD_DEF(1) MOD_DEF(2) SFP module ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw http: // www.optoway.com.tw 3/1/2006 V3.0 Optoway CONNECTION DIAGRAM SPB-7810G 4 *********************************************************************************************************************************************************************** PIN 1 2 3 4 5 6 7 8 9 10 Signal Name TX GND TX Fault TX Disable MOD-DFE2 MOD-DEF1 MOD-DEF0 N/C LOS RX GND RX GND Description Transmitter Ground Transmitter Fault Indication T ransmitter Disable (Module disables on high or open) Modulation Definition 2 – Two wires serial ID Interface Modulation Definition 1 – Two wires serial ID Interface Modulation Definition 0 – Ground in Module Not Connected Loss of Signal Receiver Ground Receiver Ground PIN 11 12 13 14 15 16 17 18 19 20 Signal Name Description RX GND Receiver Ground RX DATA OUT- Inverse Receiver Data Out RX DATA OUT+ Receiver Data Out RX GND Vcc RX Vcc TX TX GND TX DATA IN+ TX DATA INTX GND Receiver Ground Receiver Power – 3 .3V±5% Transmitter Power – 3 .3V±5% Transmitter Ground Transmitter Data In Inverse Transmitter Data In Transmitter Ground Module Definition Module Definition 4 MOD-DEF2 PIN 4 SDA MOD-DEF1 PIN 5 SCL MOD-DEF0 PIN 6 LV-TTL Low Interpretation by Host Serial module definition protocol Module Definition 4 specifies a serial definition protocol. For this definition, upon power up, MOD-DEF(1:2) appear as no connector (NC) and MOD-DEF(0) is TTL LOW. When the host system detects this condition, it activates the serial protocol. The protocol uses the 2-wire serial CMOS E 2PROM protocol of the ATMEL AT24C01A/02/04 family of components. ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw http: // www.optoway.com.tw 3/1/2006 V3.0 Optoway PACKAGE DIAGRAM Units in mm A) SC SFP SPB-7810G 5 *********************************************************************************************************************************************************************** A) LC SFP Note: Specifications subject to change without notice. ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw http: // www.optoway.com.tw 3/1/2006 V3.0