CT2016DB38400C0FLHA2

Specifications Drawing No. USY1P-H1-16609-00 Issued Date. Jun,14,2016 1 / 10 Messrs: Digi-Key Note: In case of specification change, KYOCERA Part Number also will be changed. Product Name Crystal Units with Thermistor Product Model CT2016DB Frequency 38400kHz Customer Part Number - Customer Specification Number - KYOCERA Part Number CT2016DB38400C0FLHA2 Remarks Pb-Free, RoHS Compliant, MSL 1 Customer Acceptance Accept Signature Approved Date Department Person in charge Seller KYOCERA Crystal Device Corporation Manufacturer KYOCERA Crystal Device Corporation (Sales Division) 6 Takeda Tobadono-cho, Fushimi-ku, Kyoto 612-8501 Japan TEL. No. 075-604-3421 FAX. No. 075-604-3469 (Marketing & Sales Engineering Division) 5850, Higashine-Koh, Higashine-Shi, Yamagata 999-3701 Japan TEL. No. 0237-43-5611 FAX. No. 0237-43-5615 Design Department Quality Assurance Approved by Checked by Issued by KYOCERA Crystal Device Corporation Crystal Unit Application Engineering Section S.Itoh T.Soda A.Muraoka Y.Nozaki Crystal Units Division KYOCERA Crystal Device Corporation KBS-5079G Drawing No. USY1P-H1-16609-00 2 / 10 Revision History Rev.No. 00 Description of revise First Edition Date Jun,14,2016 Approved by T.Soda Checked by A.Muraoka Issued by Y.Nozaki KYOCERA Crystal Device Corporation KBS-5079G Drawing No. USY1P-H1-16609-00 3 / 10 1. APPLICATION This specification sheet is applied to Crystal Units with Thermistor “CT2016DB” 2. KYOCERA PART NUMBER CT2016DB38400C0FLHA2 3. RATINGS Items SYMB. Rating Operating Temperature range Storage Temperature range Topr Tstg -30~+105 -40~+105 Unit °C °C Remarks 4. CHARACTERISTICS 4-1 ELECTRICAL CHARACTERISTICS Items Electrical Specification SYMB. Min Typ. Max Mode of Vibration Fundamental Nominal Frequency F0 38.4 Test Condition Unit MHz Nominal Temperature TNOM 29 °C Load Capacitance CL 7.0 pF Frequency Tolerance Frequency Temperature Characteristics Equivalent Series Resistance dF dFT -10.0 -12.0 +10.0 +12.0 ESR Drive Level Pd 0.01 Insulation Resistance IR 500 0.05 4-2 ELECTRICAL CHARACTERISTICS (Thermistor) Items Electrical Specification SYMB. Min Typ. Max Resistance 100 B-Constant 4250 Tolerance -1.0 1.0 Remarks ppm 80 Ω 0.1 mW MΩ +25±3°C -30~+85°C 100V(DC) Remarks Unit kΩ K % 25°C 25°C - 50°C KYOCERA Crystal Device Corporation KBS-5079G Drawing No. USY1P-H1-16609-00 4 / 10 5. APPEARANCES, PHYSICAL DIMENSION OUTLINE DIMENSION (not to scale) 2.00±0.10 #4 #3 #4 SENSOR #3 HOT #1 HOT #2 GND 1 1.60±0.10 384 K503Z 5 #2 #1 0.65(MAX) 2 3 4 PIN No. 6 (Side View) PIN Layout #1 HOT #2 GND #3 HOT #4 SENSOR 4-0.67±0.1 #2 4-0.59±0.1 #1 #4 MARKING 1 Nominal Frequency 2 Identification 3 Date Code #3 UNIT: mm First 3digits of the frequency are indicated. [K] is to indicate 1Pin direction Last 1 Digit of YEAR and WEEK (Ex) 2015,Jan,15  503 4 Manufacturing Location Y Japan(Yamagata) Z Japan(Shiga Yohkaichi) 5 Option Code 6 1Pin mark Alphabet & Number 2digits or blank.(For T-Sensor) KYOCERA Crystal Device Corporation KBS-5079G Drawing No. USY1P-H1-16609-00 5 / 10 6. RECOMMENDED LAND PATTERN (not to scale) 0.70 0.75 0.43 0.75 0.75 0.30 0.75 4-R0.20 UNIT : mm 0.46 KYOCERA Crystal Device Corporation KBS-5079G Drawing No. USY1P-H1-16609-00 6 / 10 7 .TAPING&REEL 7-1.Dimensions 4.0±0.1 φ1.5± 0.1 0 Unreeling direction 1.75±0.1 2.0±0.05 2.3±0.1 3.5±0.05 8.0±0.2 φ1.0+0.1/0 4.0±0.1 0.75±0.05 0.25±0.05 1.9±0.1 7-2.Leader and trailer tape Components Empty compartment Empty compartment Leader END START 100~200mm 160mm or more 400~560mm 7-3.Direction (Orientation shall be checked from the top cover tape side) Feeding direction 19200 K 401Z 19200 K 401Z 19200 K 401Z 19200 K 401Z 7-4.Specification 1. Material of the carrier tape is either polystyrene or A-PET (ESD). 2. Material of the cover tape is polyester (ESD). 3. The seal tape shall not cover the sprocket holes and not protrude from the carrier tape. 4. Tensile strength of carrier tape: 10N or more. 5. The R of the corner of each cavity is 0.2RMAX. 6. The alignment between centers of the cavity and sprocket hole shall be 0.05mm or less. 7. The orientation shall be checked from the top cover tape side as shown in 7-3. 8. Peeling force of cover tape: 0.1 to 1.0N. 9. The component will fall out naturally when cover tape is removed and set upside down. 7 11 10. Surface resistivity  Carrier tape: ≥1×10 , Cover tape :> 1×10 Over 1kg 160°~180° Cover tape 30cm/1min KYOCERA Crystal Device Corporation KBS-5079G Drawing No. USY1P-H1-16609-00 7 / 10 Reel specifications W R S U Q P φ180 Reel (3,000 pcs) Symbol Dimension Symbol Dimension P Q R φ180 +0/-3 φ60 +1/-0 φ13±0.2 S U W φ21±0.8 2.0±0.5 9±1 P Q R φ330±2.0 φ100±1.0 φ13±0.2 S U W φ21±0.8 2.0±0.5 9.4±0.5 (Unit: mm) φ330 Reel(12000pcs) Symbol Dimension Symbol Dimension (Unit : mm) KYOCERA Crystal Device Corporation KBS-5079G Drawing No. USY1P-H1-16609-00 8 / 10 8. Cautions for use (1) Soldering upon mounting There is a possibility to influence product characteristics when Solder paste or conductive glue comes in contact with product lid or surface. (2) When using mounting machine Please minimize the shock when using mounting machine to avoid any excess stress to the product. (3) Conformity of a circuit We strongly recommend to make sure that Negative resistance (Gain) of IC is designed to be 3 times the ESR (Equivalent Series Resistance) of crystal unit. 9. Storage conditions Please store product in below conditions, and use within 6 months. Temperature +18 to +30°C, and Humidity of 20 to 70 % in the packaging condition. 10. Manufacturing location Kyocera Crystal Device Corporation Yamagata Plant Kyocera Crystal Device Corporation Shiga Yohkaichi Plant Kyocera Crystal Device (Thailand) Co., Ltd 11. Quality Assurance To be guaranteed by Kyocera Crystal Device Quality Assurance Division 12. Quality guarantee In case when Kyocera Crystal Device Corporation rooted failure occurred within 1year after its delivery, substitute product will be arranged based on discussion. Quality guarantee of product after 1year of its delivery is waivered. 13. Others In case of any questions or opinions regarding the Specification, please have it in written manner within 45 days after issued date. KYOCERA Crystal Device Corporation KBS-5079G