CX1612DB48000D0FPJC1

Specifications Drawing No. USY1M-H1-17106-00 Issued Date. Feb,7,2017 1 / 10 Messrs: Digi-Key Note: Part Number will be revised in case of specification change. Product Type Quartz Crystal Series CX1612DB Frequency 48000kHz Customer Part Number - Customer Specification Number - KYOCERA Part Number CX1612DB48000D0FPJC1 Remarks Pb-Free, RoHS Compliant, MSL 1 Customer Approval Approval Signature Approved Date Department Person in charge Seller KYOCERA Crystal Device Corporation Manufacturer KYOCERA Crystal Device Corporation (Crystal Units Division) (Sales Division) 6 Takeda Tobadono-cho, Fushimi-ku, Kyoto 612-8501 Japan TEL. No. 075-604-3500 FAX. No. 075-604-3501 Design Department KYOCERA Crystal Device Corporation Crystal Unit Design Engineering Section 5850, Higashine-Koh, Higashine-Shi, Yamagata 999-3701 Japan TEL. No. 0237-43-5611 FAX. No. 0237-43-5615 Quality Assurance S.Ito Approved by T.Soda Checked by A.Muraoka Issued by T.Sudou Y.Nozaki Crystal Units Division KYOCERA Crystal Device Corporation KBS-5079G Drawing No. USY1M-H1-17106-00 2/10 Revision History Rev.No. 00 Description of revision First Edition Date Feb,7,2017 Approved by T.Soda Checked by A.Muraoka Issued by T.Sudou Y.Nozaki KYOCERA Crystal Device Corporation KBS-5079G USY1M-H1-17106-00 Drawing No. 3/10 1. APPLICATION This specification sheet is applied to quartz crystal “CX1612DB” 2. KYOCERA PART NUMBER CX1612DB48000D0FPJC1 3. RATINGS Items SYMB. Rating Unit Operating Temperature range Topr -40 to +85 °C Storage Temperature range Tstg -40 to +85 °C Remarks 4. CHARACTERISTICS ELECTRICAL CHARACTERISTICS Items Electrical Specification SYMB. Min Typ. Max Mode of Vibration Fundamental Test Condition Unit Nominal Frequency F0 48 MHz Nominal Temperature TNOM +25 °C Load Capacitance CL 8.0 pF Frequency Tolerance df/F -10.0 +10.0 Frequency Temperature Characteristics Frequency Aging Rate df/F -15.0 +15.0 -40 to +85°C -1.0 +1.0 1year Drive Level Pd 0.01 100 μW Equivalent Series Resistance Insulation Resistance ESR 50 Ω IR 500 Remarks ppm MΩ +25±3°C @35°C 100V(DC) 5. Measurement Condition 5.1 Frequency measurement Measuring instrument : IEC PI-Network Test Fixture IEC 60444-8 STD (Pi circuit 41901A) 5.2 Equivalent series resistance (ESR) measurement Measuring instrument : IEC PI-Network Test Fixture Load Capacitance : Series KYOCERA Crystal Device Corporation KBS-5079G Drawing No. USY1M-H1-17106-00 4/10 6. APPEARANCES, DIMENSIONS OUTLINE DIMENSION (not to scale) 1 (Top View) 1.60±0.10 (Connection) #4 #4 GND #3 GND (NC) 48000 1.20±0.10 #3 HOT K701Z GND #1 HOT #2 0.33± 0.03 2 #2 GND 4-R0.10 3 4 0.12± 0.05 #1 (Side View) PIN NO. #1 #2 #3 #4 PIN Layout HOT GND HOT GND(NC) (Bottom View) (8-0.05±0.05) 4-0.50±0.10 4-0.40±0.10 #2 C 0.15 UNIT: mm #4 #3 MARKING (1) Nominal Frequency First 5digits of the frequency are indicated. (2) Identification [K] is to indicate 1Pin direction. (3) Date Code Last 1 Digit of YEAR and WEEK (Ex) 2017,Jan,05 701 (4) Manufacturing Location Y: Japan(Yamagata) Z: Japan(Shiga Yohkaichi) T: Thailand *The font of marking is for reference only. KYOCERA Crystal Device Corporation KBS-5079G Drawing No. USY1M-H1-17106-00 5/10 7. RECOMMENDED LAND PATTERN (not to scale) 0.65 0.55 0.8 0.55 0.65 UNIT: mm 1.1 KYOCERA Crystal Device Corporation KBS-5079G Drawing No. USY1M-H1-17106-00 6/10 8. TAPING&REEL 8-1.Dimensions 4.0±0.1 0.5±0.05 1.5± 0.1 0 Feeding direction 1.80±0.1 8.0±0.2 1.75±0.1 2.0±0.05 4.0±0.1 0.5±0.1 0.2±0.1 1.40±0.1 8-2.Leader and Carrier tape Empty compartment Empty compartment Component END Leader START 100~200mm 160mm or more 400~560mm 8-3.Direction (Orientation shall be checked from the top cover tape side) 12345 K123 Y 12345 K123 Y 12345 K123 Y 12345 K123 Y Feeding direction 8-4.Specification 1. Material of the carrier tape is either polystyrene or A-PET (ESD). 2. Material of the cover tape is polyester (ESD). 3. The seal tape shall not cover the sprocket holes and not protrude from the carrier tape. 4. Tensile strength of carrier tape: 10N or more. 5. The R of the corner of each cavity is 0.2RMAX. 6. The alignment between centers of the cavity and sprocket hole shall be 0.05mm or less. 7. The orientation shall be checked from the top cover tape side as shown in 7-3. 8. Peeling force of cover tape: 0.1 to 1.0N. 9. The component will fall out naturally when cover tape is removed and set upside down. 165°~180° Cover tape Carrier tape KYOCERA Crystal Device Corporation KBS-5079G USY1M-H1-17106-00 Drawing No. 7/10 8-5.Reel Specification W C D E B A 180 Reel 3,000pcs (5,000 pcs Max. ) Symbol Dimension Symbol Dimension A B C 180 +0/-3 60 +1/-0 13±0.2 D E W 21±0.8 2.0±0.5 9±1 (Unit: mm) 330 Reel 20,000pcs (21,000 pcs Max. ) Symbol Dimension Symbol Dimension A B C 330±2.0 100±1.0 13±0.2 D E W 21±0.8 2.0±0.5 9.4±1 (Unit: mm) KYOCERA Crystal Device Corporation KBS-5079G Drawing No. USY1M-H1-17106-00 8/10 9. Enviromental requirements After conducting the following tests, component needs to meet below conditions. Frequency: Fluctuation within +/-10 x 10-6 CI: Fluctuation within +/-20% or 5 whichever is larger 9.1 Resistance to Shock Test condition 3 times natural drop from 100cm onto hard wooden board. 9.2 Resistance to Vibration 9.3 Resistance to Heat Test condition frequency : 10 - 55 - 10 Hz Amplitude : 1.5mm Cycle time : 15 minutes Direction : X,Y,Z (3direction),2h each. Test condition The quartz crystal unit shall be stored at a temperature of +85±2°C for 500h and subjected to room temperature for 1h before measurement. 9.4 Resistance to Cold Test condition The quartz crystal unit shall be stored at a temperature of -40±2°C for 500h and subjected to room temperature for 1h before measurement. 9.5 Thermal Shock Test condition The quartz crystal unit shall be subjected to 500 temperature cycles shown in table below,Then it shall be subjected to room temperature for 1h before mesurement. Cycle :-40±2°C (30min.)  +25±2°C (5min.)  +85±2°C (30min.)  +25±2°C (5min.) KYOCERA Crystal Device Corporation KBS-5079G Drawing No. 9.6 Resistance to Moisture USY1M-H1-17106-00 9/10 Test condition The quartz crystal unit shall be stored at a temperature of +60±2°C with relative humidity of 90% to 95% for 240 h. Then it shall be subjected to room temperature for 1h before measurement. 9.7 Soldering condition 1.) Type of solder Material : lead free solder paste Melting point : +220±5°C 2.) Reflow temp.profile Temp [°C] Time[sec] Preheating +150 to +180 150 (typ.) Peak +260±5 10 (max.) Total 300 (max.) Frequency shift : ±2ppm 3.) Hand Soldering +350°C 3 sec max 4.) Reflow Times 2 times in below Reflow temp. profile Reflow temp.profile 9.8 Bending Strength Solder this product in center of the circuit board (40mm X 100mm), and add deflection of 3mm. Test board : t=1.6mm 20 PUSH 1.6 Board 10 R5 Product 45 45 R230 Press jig UNIT: mm KYOCERA Crystal Device Corporation KBS-5079G Drawing No. USY1M-H1-17106-00 10/10 10. Cautions for use (1)Soldering upon mounting There is a possibility to influence product characteristics when Solder paste or conductive glue comes in contact with product lid or surface. (2)When using mounting machine Please minimize the shock when using mounting machine to avoid any excess stress to the product. (3)Conformity of a circuit We strongly recommend to make sure that Negative resistance (Gain) of IC is designed to be 5 times the ESR (Equivalent Series Resistance) of crystal unit. 11. Storage conditions Please store product in below conditions, and use within 6 months. Temperature +18 to +30°C, and Humidity of 20 to 70 % in the packaging condition. 12. Manufacturing location Kyocera Crystal Device Corporation Yamagata Plant Kyocera Crystal Device Corporation Shiga Yohkaichi Plant Kyocera Crystal Device (Thailand) Co., Ltd 13. Quality Assurance To be guaranteed by Kyocera Crystal Device Quality Assurance Division 14. Quality guarantee In case when Kyocera Crystal Device Corporation rooted failure occurred within 1year after its delivery, substitute product will be arranged based on discussion. Quality guarantee of product after 1year of its delivery is waivered. 15. Others In case of any questions or opinions regarding the Specification, please have it in written manner within 45 days after issued date. KYOCERA Crystal Device Corporation KBS-5079G