CX3225CA12000D0KPSC1

Specification Drawing No. UKY1C-H1-18412-00[43] 1/10 Issued Date. Jun.4,2018 TO: Digi-Key Note：In case of specification change, KYOCERA Part Number also will be changed. Product Name Quartz Crystal Product Model CX3225CA Frequency 12000kHz Customer Part Number - Customer Specification Number - KYOCERA Part Number CX3225CA12000D0KPSC1 Remarks RoHS Compliant、MSL 1 AEC-Q200 Compliant Customer Acceptance Accept Signature Approved Date Department Person in charge Seller KYOCERA Corporation Manufacturer Corporate Electronic Components Group Electronic Components Sales Division 6 Takeda Tobadono-cho, Fushimi-ku, Kyoto 612-8501 Japan TEL. No. 075-604-3500 FAX. No. 075-604-3501 Corporate Electronic Components Group Crystal Components Division Design Department Quality Assurance Approved by Examination by Issued by KYOCERA Corporation Crystal Units Design Engineering Yamagata Section W.Muraoka Y.Takahashi A.Ito Y. Kikuchi Crystal Product Division KYOCERA Corporation KBS-5079J Drawing No. UKY1C-H1-18412-00[43] 2/10 Revision History Rev.No. 1 Description of revise First Edition Date Approved by Examination by Issued by Jun.4,2018 Y.Takahashi A.Ito Y. Kikuchi KYOCERA Corporation KBS-5079J Drawing No. UKY1C-H1-18412-00[43] 3/10 1. APPLICATION This specification sheet is applied to quartz crystal “CX3225CA12000D0KPSC1” 2. KYOCERA PART NUMBER CX3225CA12000D0KPSC1 3. RATINGS Items SYMB. Rating Unit Operating Temperature Topr -40 to +85 °C Storage Temperature Range Tstg -40 to +150 °C Remarks 4. CHARACTERISTICS ELECTRICAL CHARACTERISTICS Items SYMB. Electrical Specification Min. Typ. Max. Fundamental Unit F0 12 MHz TNOM +25 °C CL 8.0 pF Mode of Vibration Nominal Frequency Nominal Temperature Load Capacitance Frequency Tolerance Frequency Temperature Characteristics Frequency Aging Rate Equivalent Series Resistance df/F -30.0 +30.0 df/F -50.0 +50.0 Test Condition Remarks +25±3°C -40 to +85°C PPM -5.0 ESR Drive Level Pd 0.01 Insulation Resistance IR 500 1st year +5.0 200 Ω 200 µW MΩ +25±3°C 100V(DC) KYOCERA Corporation KBS-5079J Drawing No. UKY1C-H1-18412-00[43] 4/10 5. Measurement Condition 5.1 Frequency measurement Measuring instrument : IEC PI-Network Test Fixture Load Capacitance : 8.0pF Drive Level : 10µW 5.2 Equivalent series resistance (ESR) measurement Measuring instrument : IEC PI-Network Test Fixture Load Capacitance : Series Drive Level : 10µW KYOCERA Corporation KBS-5079J Drawing No. UKY1C-H1-18412-00[43] 5/10 6. APPEARANCES, PHYSICAL DIMENSION OUTLINE DIMENSION (not to scale) ① (Top View) (Connection) NC 4－R0.20 3.20±0.1 Pin4 Pin4 HOT Pin3 Pin1 HOT Pin2 NC Pin3 2.50±0.1 12000 K801Y 0.2±0.05 ② ③ ④ (Side View) 0.8±0.1 Pin2 Pin1 4－0.2±0.1 (Bottom View) 4－1.00±0.1 Pin2 Pin1 C 0.30 Pin4 Pin3 4－0.75±0.1 8－0.10±0.1 PIN No. #1 #2 #3 #4 PIN Layout HOT NC HOT NC ※There is not consistency of a direction of indication for NC. UNIT： mm MARKING 1 Nominal Frequency Move the number of maximum indication beams of the frequency to five digits，and omit less than kHz． 2 Identification 3 Date Code Year…LAST 1 DIGIT of YEAR AND WEEK (Ex) Jan. 1, 2018 → 801 4 Manufacturing Location Y…Japan(Yamagata) ※The font of marking is reference. KYOCERA Corporation KBS-5079J Drawing No. UKY1C-H1-18412-00[43] 6/10 7. RECOMMENDED LAND PATTERN (not to scale) 1.0 1.3 1.05 0.8 1.05 1.3 UNIT： mm KYOCERA Corporation KBS-5079J Drawing No. UKY1C-H1-18412-00[43] 7/10 8.TAPING & REEL 8-1.Dimensions 4.0±0.1 φ1.55±0.05 Unreeling direction 1.75±0.1 2.0±0.05 (3.7) 3.5±0.1 3.5±0.05 (3.0) 2.8±0.1 1.0±0.1 4.0±0.1 0.25±0.05 8.0±0.2 φ1.05±0.15 8-2.Leader and trailer tape Empty compartment Empty compartment Component END START 400～500mm 400～500mm 8-3.Direction（The direction shall be seen from the top cover tape side） Unreeling direction 8-4.Specification 1. Material of the carrier tape is either polystyrene or A－PET (ESD). 2. Material of the cover tape is polyester (ESD). 3. The seal tape shall not cover the sprocket holes and not protrude from the carrier tape. 4. Tensile strength of carrier tape: 10N or more. 5. The R of the corner of each cavity is 0.2RMAX. 6. The alignment between centers of the cavity and sprocket hole shall be 0.05mm or less. 7. Peeling force of cover tape: 0.1 to 1.0N. 8. The component will fall out naturally when cover tape is removed and set upside down. 9. The marking on parts is not fixed its direction, its electrical characteristic is equal. 165°～180° Cover tape Career tape KYOCERA Corporation KBS-5079J Drawing No. UKY1C-H1-18412-00[43] 8/10 8-5.Reel specifications W C t D E B A (Nonconductor type Reel) Φ180 Reel (3000pcs max.) Dimension Symbol Dimension A B C D φ180 +0/-1.5 φ60 +1/-0 φ13±0.2 φ21±0.8 E W t 2.0±0.5 9±1 2.0±0.5 (Unit : mm) KYOCERA Corporation KBS-5079J Drawing No. UKY1C-H1-18412-00[43] 9/10 9.Enviromental requirements (Reference: AEC-Q200 Rev. D. The solder used by examination is hereafter set to Sn-3Ag-0.5Cu.) After following test, Frequency applies to each item and CI, ±20% or 5Ω of large value. No 9.1 Stress High Temperature Exposure (Storage) Reference MIL-STD-202 Method 108 9.2 Temperature Cycling JESD22 Method JA-104 9.3 Biased Humidity MIL-STD- 202 Method 103 9.4 Operational Life MIL-STD- 202 Method 108 9.5 Terminal Strength (Leaded) 9.6 Resistance to Solvents 9.7 Mechanical Shock 9.8 Vibration MIL-STD- 202 Method 211 MIL-STD- 202 Method 215 MIL-STD-202 Method 213 MIL-STD-202 Method 204 9.9 Resistance to Soldering Heat MIL-STD-202 Method 210 9.10 Solder ability J-STD-002 9.11 9.12 9.13 Flammability Board Flex Terminal Strength(SMD) UL-94 AEC Q200-005 AEC Q200-006 Additional Requirements 1000 hrs. at rated operating temperature (e.g. 85°C part can be stored for 1000 hrs at 85°C. Same applies for 125°C). Unpowered. Measurement at 24±4 hours after test conclusion. 1000 cycles (-40°C to 125°C) Note: If 85°C part the 1000 cycles will be at that temperature rating. Measurement at 24±4 hours after test conclusion. 30min maximum dwell time at each temperature extreme. 1 min. maximum transition time. 1000 hours 85°C/85%RH. Rated VDD applied with 1 MW and inverter in parallel, 2X crystal CL capacitors between each crystal leg and GND. Measurement at 24±4 hours after test conclusion. Note: 1000 hrs @ 125°C. If 85°C part will be tested at that temperature. Rated VDD applied with 1 MW and inverter in parallel, 2X crystal CL capacitors between each crystal leg and GND. Measurement at 24±4 hours after test conclusion. Test leaded device lead integrity only. Conditions: A (227 g), C (227 g). Note: Also aqueous wash chemical - OKEM clean or equivalent. Do not use banned solvents. Figure 1 of Method 213. Condition C 5g's for 20 minutes 12 cycles each of 3 orientations. Note: Use 8"X5" PCB .031" thick with 7 secure points on one 8" side and 2 secure points on corners of opposite sides. Parts mounted within 2" from any secure point. Test from 10-2000 Hz. Condition B No pre-heat of samples. Note: Single Wave solder - Procedure 1 with solder within 1.5 mm of device body for Leaded. Procedure 1 except 230°C and immerse only to level to cover terminals for SMD. For both Leaded & SMD. Electrical Test not required. Magnification 50 X. Conditions: Leaded: Method A @ 235°C, category 3. SMD: a) Method B, 4 hrs @ 155°C dry heat @ 235°C b) Method B @ 215°C category 3. c) Method D category 3 @ 260°C. V-0 or V-1 Acceptable 60 sec minimum holding time. - KYOCERA Corporation KBS-5079J Drawing No. UKY1C-H1-18412-00[43] 10/10 10. Cautions for use （1）Soldering upon mounting There is a possibility to influence product characteristics when Solder paste or conductive glue comes in contact with product lid or surface. （2）When using mounting machine Please minimize the shock when using mounting machine to avoid any excess stress to the product. （3）Conformity of a circuit We strongly recommend to make sure that Negative resistance (Gain) of IC is designed to be 10 times the ESR (Equivalent Series Resistance) of crystal unit. （4）After making the Quartz Crystal mount on a printed circuit board ,if it is required to divide the printed circuit board into another one, use it with attentive confirmation so that a warp cased by this dividing might not affect any damage. When designing a printed circuit board as well as handling the mounting As much as possible. The quartz crystal shall be passed through the reflow furnace. Then it shall be subjected to standard atmospheric conditions, after which cleaning shall be made. 11. Storage conditions Please store product in below conditions, and use within 6 months. Temperature +18 to +30°C, and Humidity of 20 to 70 % in the packaging condition. 12. Manufacturing location Kyocera Corporation Yamagata Higashine plant / Japan(Yamagata) 13. Quality Assurance To be guaranteed by Kyocera Corporation Yamagata Higashine plant Quality Assurance Division 14. Quality guarantee In case when Kyocera Corporation rooted failure occurred within 1year after its delivery, substitute product will be arranged based on discussion. Quality guarantee of product after 1year of its delivery is waivered. 15. Others In case of any questions or opinions regarding the Specification, please have it in written manner within 45 days after issued date. KYOCERA Corporation KBS-5079J