CX3225SA40000D0PTWCC

Drawing No. UKY1C-H1-18849-00[43] 3/9 1. APPLICATION This specification sheet is applied to quartz crystal “CX3225SA40000D0PTWCC” 2. KYOCERA PART NUMBER CX3225SA40000D0PTWCC 3. RATINGS Items SYMB. Rating Unit Operating Temperature Topr -40 to +150 °C Storage Temperature range Tstg -40 to +150 °C Remarks 4. CHARACTERISTICS ELECTRICAL CHARACTERISTICS Items Electrical Specification SYMB. Min Typ. Max Mode of Vibration Fundamental Test Condition Unit Nominal Frequency F0 40 MHz Nominal Temperature Load Capacitance TNOM 25 °C CL 8.0 pF Frequency Tolerance Frequency Temperature characteristics Frequency Aging Rate Equivalent Series Resistance Drive Level df/F -50.0 +50.0 +25±3°C df/F -200.0 +200.0 -40 to +150°C Insulation Resistance Remarks PPM -2.0 ESR Pd 0.01 IR 500 1st year +2.0 50 Ω 200 µW MΩ +25±3°C 100V(DC) 5. Measurement Condition 5.1 Frequency measurement Measuring instrument : IEC PI-Network Test Fixture Load Capacitance : 8.0pF Drive Level : 10µW 5.2 Equivalent series resistance (ESR) measurement Measuring instrument : IEC PI-Network Test Fixture Load Capacitance : Series Drive Level : 10µW KYOCERA Corporation KBS-5079J Drawing No. UKY1C-H1-18849-00[43] 4/9 6. APPEARANCES, PHYSICAL DIMENSION OUTLINE DIMENSION (not to scale) 1 (Top View) (Connection) 3.20±0.1 #4 #3 HOT 2.50±0.1 40000 ○K801Y #2 4－Ｒ0.20 #1 5 2 3 (Side View) #2 GND PIN NO. #1 #2 #3 #4 4－0.15±0.1 (Bottom View) 4－0.11±0.1 #1 HOT 4 0.20±0.1 0.8MAX #4 GND #3 PIN Layout HOT GND HOT GND 4－1.15±0.1 #1 4－0.75±0.10 #2 C 0.30 UNIT : mm #4 #3 MARKING 1 Nominal Frequency Move the number of maximum indication beams of the frequency to five digits，and omit less than kHz． 2 Identification [K] mark is surely 1Pin direction. 3 Date Code Year…LAST 1 DIGIT of YEAR AND WEEK (Ex)Jan,01, 2018 → 801 4 Manufacturing Location Y…Japan(Yamagata) 5 No.1 pin is expressed. ※The font of marking is reference. KYOCERA Corporation KBS-5079J Drawing No. UKY1C-H1-18849-00[43] 5/9 7. RECOMMENDED LAND PATTERN (not to scale) 0.7 1.45 1.05 0.8 1.05 1.45 UNIT： mm KYOCERA Corporation KBS-5079J Drawing No. UKY1C-H1-18849-00[43] 6/9 8.TAPING & REEL 8-1.Dimensions 4.0±0.1 φ1.55±0.05 Unreeling direction 1.75±0.1 2.0±0.05 (3.7) 3.5±0.1 3.5±0.05 (3.0) 2.8±0.1 1.0±0.1 4.0±0.05 0.25±0.05 8.0±0.2 φ1.05±0.1 8-2.Leader and trailer tape Empty compartment Empty compartment Component END START 400～500mm 400～500mm 8-3.Direction（The direction shall be seen from the top cover tape side） Unreeling direction 12345 ○K123Y 12345 ○K123Y 12345 ○K123Y 12345 ○K123Y 8-4.Specification 1. Material of the carrier tape is either polystyrene or A－PET (ESD). 2. Material of the cover tape is polyester (ESD). 3. The seal tape shall not cover the sprocket holes and not protrude from the carrier tape. 4. Tensile strength of carrier tape: 10N or more. 5. The R of the corner of each cavity is 0.2RMAX. 6. The alignment between centers of the cavity and sprocket hole shall be 0.05mm or less. 7. The orientation shall be checked from the top cover tape side as shown in 8-3. 8. Peeling force of cover tape: 0.1 to 1.0N. 9. The component will fall out naturally when cover tape is removed and set upside down. Cover tape 165°～180° Career tape KYOCERA Corporation KBS-5079J Drawing No. UKY1C-H1-18849-00[43] 7/9 8-5.Reel specifications t W C D E B A φ180 Reel(3,000pcs max.) Symbol Dimension A B C D φ180 +0/-3 φ60 +1/-0 φ13±0.2 φ21±0.8 E W t 2.0±0.5 9±1 2.0±0.5 Symbol Dimension (Unit : mm) φ330 Reel(10,000pcs max.) Symbol Dimension Symbol Dimension A B C D φ330±2.0 φ100±1.0 φ13±0.2 φ21±0.8 E W t 2.0±0.5 9.5±0.5 2.2±0.1 (Unit : mm) KYOCERA Corporation KBS-5079J Drawing No. UKY1C-H1-18849-00[43] 8/9 9. ENVIRONMENTAL AND MECHANICAL CHARACTERISTICS ： No 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9 9.10 9.11 9.12 9.13 (Reference: AEC-Q200 Rev. D. The solder used by examination is hereafter set to Sn-3Ag-0.5Cu.) After following test, Frequency applies to each item and CI, ±20% or 5Ω of large value. Stress Reference Additional Requirements High Temperature Exposure MIL-STD-202 1000 hrs. at rated operating temperature (e.g. 85°C (Storage) Method 108 part can be stored for 1000 hrs at 85°C. Same applies for 125°C). Unpowered. Measurement at 24±4 hours after test conclusion. Temperature Cycling JESD22 1000 cycles (-40°C to 125°C) Note: If 85°C part the Method JA-104 1000 cycles will be at that temperature rating. Measurement at 24±4 hours after test conclusion. 30min maximum dwell time at each temperature extreme. 1 min. maximum transition time. Biased Humidity MIL-STD- 202 1000 hours 85°C/85%RH. Rated VDD applied with 1 Method 103 MW and inverter in parallel, 2X crystal CL capacitors between each crystal leg and GND. Measurement at 24±4 hours after test conclusion. Operational Life MIL-STD- 202 Note: 1000 hrs @ 125°C. If 85°C part will be tested at Method 108 that temperature. Rated VDD applied with 1 MW and inverter in parallel, 2X crystal CL capacitors between each crystal leg and GND. Measurement at 24±4 hours after test conclusion. Terminal Strength (Leaded) MIL-STD- 202 Test leaded device lead integrity only. Conditions: A Method 211 (227 g), C (227 g). Resistance to Solvents MIL-STD- 202 Note: Also aqueous wash chemical - OKEM clean or Method 215 equivalent. Do not use banned solvents. Mechanical Shock MIL-STD-202 Figure 1 of Method 213. Condition C Method 213 Vibration MIL-STD-202 5g's for 20 minutes 12 cycles each of 3 orientations. Method 204 Note: Use 8"X5" PCB .031" thick with 7 secure points on one 8" side and 2 secure points on corners of opposite sides. Parts mounted within 2" from any secure point. Test from 10-2000 Hz. Resistance to MIL-STD-202 Condition B No pre-heat of samples. Note: Single Soldering Heat Method 210 Wave solder - Procedure 1 with solder within 1.5 mm of device body for Leaded. Procedure 1 except 230°C and immerse only to level to cover terminals for SMD. Solder ability J-STD-002 For both Leaded & SMD. Electrical Test not required. Magnification 50 X. Conditions: Leaded: Method A @ 235°C, category 3. SMD: a) Method B, 4 hrs @ 155°C dry heat @ 235°C b) Method B @ 215°C category 3. c) Method D category 3 @ 260°C. Flammability UL-94 V-0 or V-1 Acceptable Board Flex AEC Q200-005 60 sec minimum holding time. Terminal Strength(SMD) AEC Q200-006 - KYOCERA Corporation KBS-5079J Drawing No. UKY1C-H1-18849-00[43] 9/9 10. Cautions for use （1）Soldering upon mounting There is a possibility to influence product characteristics when Solder paste or conductive glue comes in contact with product lid or surface. （2）When using mounting machine Please minimize the shock when using mounting machine to avoid any excess stress to the product. （3）Conformity of a circuit We strongly recommend to make sure that Negative resistance (Gain) of IC is designed to be 10 times the ESR (Equivalent Series Resistance) of crystal unit. 11. Storage conditions Please store product in below conditions, and use within 6 months. Temperature +18 to +30°C, and Humidity of 20 to 70 % in the packaging condition. 12. Manufacturing location Kyocera Corporation Yamagata Higashine Plant / Japan(Yamagata) 13. Quality Assurance To be guaranteed by Kyocera Corporation Yamagata Higashine Plant Quality Assurance Division 14. Quality guarantee In case when Kyocera Corporation rooted failure occurred within 1year after its delivery, substitute product will be arranged based on discussion. Quality guarantee of product after 1year of its delivery is waivered. 15. Others In case of any questions or opinions regarding the Specification, please have it in written manner within 45 days after issued date. KYOCERA Corporation KBS-5079J