CX3225SB26000D0FFFCC

Specifications Drawing No. UKY1C-H1-14570-00[43] 1/11 Issued Date. May,16,2014 TO: Digi-Key Note：In case of specification change, KYOCERA Part Number also will be changed. Product Name Quartz Crystal Product Model CX3225SB Frequency Refer to UKY1C-H1-14570-00[43] 3/11 Nominal Frequency Customer Part Number - Customer Specification Number - KYOCERA Part Number Refer to UKY1C-H1-14570-00[43] 3/11 Nominal Frequency Remarks Pb-Free、RoHS Compliant、MSL 1 Customer Acceptance Accept Signature Approved Date Department Person in charge Seller KYOCERA Crystal Device Corporation Manufacturer (Crystal products Sales Division) 6 Takeda Tobadono-cho, Fushimi-ku, Kyoto 612-8501 Japan TEL. No. 075-604-3500 FAX. No. 075-604-3501 Crystal Units Division Design Department 5850, Higashine-Koh, Higashine-Shi, Yamagata 999-3701 Japan TEL. No. 0237-43-5611 FAX. No. 0237-43-5615 Quality Assurance Approved by Checked by Issued by KYOCERA Crystal Device Corporation Crystal Units Engineering Section A. Kikuchi Y.Takahashi Crystal Units Division T. Nitoube Y. Kikuchi KYOCERA Crystal Device Corporation KBS-5079F Drawing No. UKY1C-H1-14570-00[43] 2/11 Revision History Rev.No. 1 Description of revise First Edition Date Approved by Checked by Issued by May,16,2014 Y.Takahashi T. Nitoube Y. Kikuchi KYOCERA Crystal Device Corporation KBS-5079F Drawing No. UKY1C-H1-14570-00[43] 3/11 [PART NUMBER LIST] Nominal Frequency (MHz) KYOCERA Part Number ESR (Ω) 25.000 26.000 27.000 32.000 38.400 40.000 48.000 CX3225SB25000D0FFFCC CX3225SB26000D0FFFCC CX3225SB27000D0FFFCC CX3225SB32000D0FFFCC CX3225SB38400D0FFFCC CX3225SB40000D0FFFCC CX3225SB48000D0FFFCC 50 50 50 50 50 50 50 Nominal Frequency Code 25000 26000 27000 32000 38400 40000 48000 KYOCERA Crystal Device Corporation KBS-5079F Drawing No. UKY1C-H1-14570-00[43] 4/11 1. APPLICATION This specification sheet is applied to quartz crystal “CX3225SB” 2. KYOCERA PART NUMBER Refer to UKY1C-H1-14570-00[43] 3/11 Nominal Frequency 3. RATINGS Items SYMB. Rating Unit Operating Temperature Topr -20 to +70 °C Storage Temperature range Tstg -40 to +85 °C Remarks 4. CHARACTERISTICS ELECTRICAL CHARACTERISTICS Items Electrical Specification SYMB. Min Typ. Max Mode of Vibration Fundamental Test Condition Unit Nominal Frequency F0 ※1 MHz Nominal Temperature Load Capacitance TNOM +25 °C CL 8.0 pF Frequency Tolerance Frequency Temperature characteristics Frequency Aging Rate Equivalent Series Resistance Drive Level df/F -10.0 +10.0 +25±3°C df/F -10.0 +10.0 -20 to +70°C Insulation Resistance Remarks PPM -1.0 ESR Pd 0.01 IR 500 +1.0 1 year ※2 Ω 100 μW MΩ +25±3°C 100V(DC) ※1 Refer to UKY1C-H1-14570-00[43] 3/11 Nominal Frequency ※2 Refer to UKY1C-H1-14570-00[43] 3/11 ESR KYOCERA Crystal Device Corporation KBS-5079F Drawing No. UKY1C-H1-14570-00[43] 5/11 5. APPEARANCES, PHYSICAL DIMENSION OUTLINE DIMENSION (not to scale) 1 （TOP VIEW） 3.20±0.10 #4 #4 GND #3 2.50±0.10 ※ 3 K401Y #2 #1 HOT #2 GND 4－R0.20 3 4 8－0.10±0.1 PIN NO. #1 #2 #3 #4 PIN Layout HOT GND HOT GND 4－1.0±0.1 #2 #1 4－0.75±0.1 2 0.20±0.04 0.55±0.05 #1 C 0.30 #4 #3 HOT #3 UNIT： mm MARKING 1 Nominal Frequency Move the number of maximum indication beams of the frequency to five digits，and omit less than kHz． 2 Identification [K] mark is surely 1Pin direction. 3 Date Code Year…LAST 1 DIGIT of YEAR AND WEEK (Ex)Jan, 01, 2014 → 401 4 Manufacturing Location Y…Yamagata Z…Shiga Yohkaichi T…Thailand F…Philippines ※3 Refer to UKY1C-H1-14570-00[43] 3/11 Nominal Frequency Code ※The font of marking is reference. KYOCERA Crystal Device Corporation KBS-5079F Drawing No. UKY1C-H1-14570-00[43] 6/11 6. RECOMMENDED LAND PATTERN (not to scale) 1.0 1.3 1.05 1.85 0.8 1.05 1.3 UNIT： mm 2.3 KYOCERA Crystal Device Corporation KBS-5079F Drawing No. UKY1C-H1-14570-00[43] 7/11 7.TAPING & REEL 7-1.Dimensions 4.0±0.1 φ1.55±0.05 Unreeling direction 1.75±0.1 2.0±0.05 (3.7) 3.5±0.1 3.5±0.05 (3.0) 2.8±0.1 1.0±0.1 4.0±0.05 0.25±0.05 8.0±0.2 φ1.05±0.1 7-2.Leader and trailer tape Components Empty compartment Empty compartment Leader END START 160mm or more 100～200mm 400～560mm 7-3.Direction（The direction shall be seen from the top cover tape side） Unreeling direction 12345 K123Y 12345 K123Y 12345 K123Y 12345 K123Y 7-4.Specification 1.Material of the carrier tape shall be polystyrene or A－PET (ESD). 2.Material of the seal tape shall be polyester(ESD). 3.The seal tape shall not cover the sprocket holes. And not protrude from the carrier tape. 4.Tensile strength of the tape : 10N or more. 5.The R of the corner without designation is 0.2RMAX. 6.Disalignment between centers of the cavity and sprocket hole shall be 0.05mm or less. 7.Cumulative pitch tolerance of “P0” shall be ±0.2mm at 10 pitches. 8.Suppose that it unifies as shown in the above-mentioned figure to the directivity of printing in an embossing tape. 9. Peeling force of the seal tape: 0.1 to 1.0N. 10.The component can fall headlong naturally from taping in the environment, such dry conditions, when this components were transferred to, cover was removed and the component was moved upside down. 165°～180° Cover tap Career tape KYOCERA Crystal Device Corporation KBS-5079F Drawing No. UKY1C-H1-14570-00[43] 8/11 7-5.Reel Specification t W C D E B A In the case of Φ180 Reel (3,000 pcs max, every 1,000 pcs) Symbol Dimension Symbol Dimension A B C D φ180 +0/-3 φ60 +1/-0 φ13±0.2 φ21±0.8 E W t 2.0±0.5 9±1 2.0±0.5 (Unit : mm) In the case of Φ330 Reel (10,000 pcs max, every 1,000 pcs) Symbol Dimension Symbol Dimension A B C D φ330±2.0 φ100±1.0 φ13±0.2 φ21±0.8 E W t 2.0±0.5 9.5±0.5 2.2±0.1 (Unit : mm) KYOCERA Crystal Device Corporation KBS-5079F Drawing No. UKY1C-H1-14570-00[43] 9/11 8. Environmental requirements After following test, frequency shall not change more than ±10×10－６ And CI，±20% or 5Ω of large value. 8.1 Resistance to Shock Test condition Natural dropped from height 100cm onto hard wood board in 3 times 8.2 Resistance to Vibration 8.3 Resistance to Heat Test condition frequency ： 10 - 55 - 10 Hz Amplitude ： 1.5mm Cycle time ： 15 minutes Direction ： X,Y,Z (3direction),2 h each. Test condition The quartz crystal unit shall be stored at a temperature of +85±2°C for 500 h. Then it shal be subjected to standard atmospheric conditions for 1 h ,after whichi measurement shall be made. 8.4 Resistance to Cold Test condition The quartz crystal unit shall be stored at a temperature of -40±2°C for 500 h. Then it shal be subjected to standard atmospheric conditions for 1 h ,after whichi measurement shall be made. 8.5 Thermal Shock Test condition The quartz crystal unit shall be subjected to 500 succesive change of temperature cycles ，each as shown in table below，Then it shall be subjected to standard atmospheric conditions for 1h，after which measurements shall be made. Cycle ：-40±2°C（30min.）to +25±2°C（5min.） to +85±2°C（30min.）to +25±2°C（5min.） KYOCERA Crystal Device Corporation KBS-5079F Drawing No. 8.6 Resistance to Moisture 8.7 Soldering condition UKY1C-H1-14570-00[43] 10/11 Test condition The quartz crystal unit shall be stored at a temperature of +60±2°C wich relative humidity of 90% to 95% for 240 h. Then it shall be subjected to standard atmospheric conditions for 1h，after which measurements shall be made 1.） Material of solder Kind … lead free solder paste Melting point … +220±5°C 2.） Reflow temp.profile Temp [°C] Preheating +150 to +180 Peak +260±5 Total ― Frequency shift : ±2ppm 3.） Hand Soldering +350°C 3 sec MAX 4.） Reflow Times 2 times Time[sec] 150 (typ.) 10 (max.) 300 (max.) Reflow temp.profile 8.8 Intensity for bending in circuit board Solder this product in center of the circuit board of 40mm×100mm， and add the deflection of 3mm as the bottom figure. Test board : t＝1.6mm 20 PUSH 1.6 board 10 R5 Product 45 45 R230 press jig UNIT : mm KYOCERA Crystal Device Corporation KBS-5079F Drawing No. UKY1C-H1-14570-00[43] 11/11 9. Cautions for use （1）Soldering in mounting In case of Solder paste and conductive glue contact product lid or product side face exception for product terminal it’s possible to influence product characteristics. Please be careful above contents. （2）Automatic mounting machine use Please use after affirmation that select the mounting machine model with a shock small if possible in the case of use of an automatic mounting machine, and it does not have breakage. There is a risk of a quartz crystal unit breakage occurring and not functioning normally by too much shock etc. （3）Conformity of a circuit In case of use of an oscillation circuit, please insert in a crystal oscillating child in series resistance 5 times as many as the standard value of equivalent in-series resistance, and confirm oscillating. Please remove resistance which inserted after the notes above-mentioned examination in the quartz crystal unit in series, and use it. 10. Storage conditions Storage at prolonged high temperature or low temperature and the storage by high humidity cause degradation of frequency accuracy, and degradation of soldering nature. Storage is performed at the temperature of +18 to +30°C, and the humidity of 20 to 70 % in the state of packing, and a term is 6 months. 11. Manufacturing location Kyocera Crystal Device Corporation Kyocera Crystal Device Corporation Shiga Yohkaichi Plant Kyocera Crystal Device (Thailand) Co., Ltd Kyocera Crystal Device Philippines, Inc. 12. Quality Assurance Kyocera Crystal Device Quality Assurance Division 13. Quality guarantee When the failure by the responsibility of our company occurs clearly after delivery within 1 year, a substitute article etc. is appropriated gratuitously and this is guaranteed. However, when passing 1 year after delivery, there is a case where I am allowed to consider as onerous repair after both consultation. 14. Others When any questions and opinions are in the written matter of these delivery specifications, I will ask connection of you from the company issue day within 45 days. In a connection no case, a written matter is consented to it and employed within a term. KYOCERA Crystal Device Corporation KBS-5079F