CX5032GB19200P0HEQZ1

Specifications Drawing No. UKY1C-H1-14560-00[40] 1/11 Issued Date. MAY.16,2014 TO: Digi-Key Note：In case of specification change, KYOCERA Part Number also will be changed. Product Name Quartz Crystal Product Model CX5032GB Frequency Refer to UKY1C-H1-14560-00[40] 3/11 Nominal Frequency Customer Part Number - Customer Specification Number - KYOCERA Part Number Refer to UKY1C-H1-14560-00[40] 3/11 KYOCERA Part Number Remarks Pb-Free、RoHS Compliant、MSL 1 Customer Acceptance Accept Signature Approved Date Department Person in charge Seller KYOCERA Crystal Device Corporation Manufacturer (Crystal products Sales Division) 6 Takeda Tobadono-cho, Fushimi-ku, Kyoto 612-8501 Japan TEL. No. 075-604-3500 FAX. No. 075-604-3501 Crystal Units Division Design Department 5850, Higashine-Koh, Higashine-Shi, Yamagata 999-3701 Japan TEL. No. 0237-43-5611 FAX. No. 0237-43-5615 Quality Assurance Approved by Checked by Issued by KYOCERA Crystal Device Corporation Crystal Units Engineering Section A. Kikuchi Y.Takahashi Crystal Units Division T. Nitoube M. Abe KYOCERA Crystal Device Corporation KBS-5079F Drawing No. UKY1C-H1-14560-00[40] 2/11 Revision History Rev.No. 1 Description of revise First Edition Date Approved by Checked by Issued by MAY,16,2014 Y.Takahashi T. Nitoube M. Abe KYOCERA Crystal Device Corporation KBS-5079F Drawing No. UKY1C-H1-14560-00[40] 3/11 [PART NUMBER LIST] Nominal Frequency Code Nominal Frequency (MHz) KYOCERA Part Number ESR (Ω) 8.000 CX5032GB08000H0HPQZ1 300 Drive Level (μW) 500 10.000 CX5032GB10000H0HPQZ1 150 500 10000 12.000 CX5032GB12000H0HPQZ1 150 500 12000 16.000 CX5032GB16000H0HPQZ1 100 300 16000 8000 KYOCERA Crystal Device Corporation KBS-5079F Drawing No. UKY1C-H1-14560-00[40] 4/11 1. APPLICATION This specification sheet is applied to quartz crystal “CX5032GB” 2. KYOCERA PART NUMBER Refer to UKY1C-H1-14560-00[40] 3/11 KYOCERA Part Number 3. RATINGS Items SYMB. Rating Unit Operating Temperature Topr -40 to +85 °C Storage Temperature Range Tstg -40 to +85 °C Remarks 4. CHARACTERISTICS 4-1 ELECTRICAL CHARACTERISTICS Items SYMB. Electrical Specification Min. Typ. Max. Fundamental Unit F0 ※1 MHz TNOM +25 °C CL 12.0 pF Mode of Vibration Nominal Frequency Nominal Temperature Load Capacitance Frequency Tolerance Frequency Temperature Characteristics Frequency Aging Rate Equivalent Series Resistance Drive Level Insulation Resistance df/F -20.0 +20.0 df/F -30.0 +30.0 Test Condition Remarks +25 3°C -40 to +85°C PPM -5.0 ESR Pd 0.01 IR 500 +5.0 1 year ※2 Ω ※3 μW MΩ +25 3°C 100V(DC) ※1 Refer to UKY1C-H1-14560-00[40] 3/11 Nominal Frequency ※2 Refer to UKY1C-H1-14560-00[40] 3/11 ESR ※3 Refer to UKY1C-H1-14560-00[40] 3/11 Drive Level KYOCERA Crystal Device Corporation KBS-5079F Drawing No. UKY1C-H1-14560-00[40] 5/11 5. APPEARANCES, PHYSICAL DIMENSION OUTLINE DIMENSION (not to scale) 2 ※４ 1 KSS 4AF 4 B 1.10max. 3 2.0±0.2 3.2±0.2 0.8±0.2 D C A 0.3±0.1 2.4±0.2 5.0±0.2 4‐R0.13 4-R0.15 A Terminal W-Ni-Au(Pb-Free) B CAP CERAMICS（BLACK） C BASE CERAMICS（BLACK） D GLASS LOW TEMPERATURE GLASS MARKING NOTE NOMINAL FREQUENCY （5 DIGITS MAX） UNIT： kHz 1 Unit : mm ※ 4 Refer to UKY1C-H1-14560-00[40] 3/11 Nominal Frequency Code 2 IDENTIFICATION － 3 DATE CODE YEAR ：LAST 1 DIGIT MONTH ：JAN(A)～DEC(M)，EXCEPT(I) EXAMPLE ：Jan,2014…4A 4 MANUFACTURING LOCATION F： Philippines Y：Yamagata * The font of marking is reference. KYOCERA Crystal Device Corporation KBS-5079F Drawing No. UKY1C-H1-14560-00[40] 6/11 6. RECOMMENDED LAND PATTERN (not to scale) 1.9 2.4 ＋ 1.9 Unit：mm 4.1 KYOCERA Crystal Device Corporation KBS-5079F Drawing No. UKY1C-H1-14560-00[40] 7/11 7. TAPING & REEL 7.1 Carry tape dimension 4.00.1 φ1.55±0.05 Unreeling direction 2.00.1 5.40.1 1.750.10 5.5 0.1 12.00.3 φ1.55±0.05 8.00.1 Unit : mm 1.70.1 0.300.05 3.60.1 7.2 Leader and trailer tape Empty compartment SMD parts taped area Empty compartment END START 160 mm min. 400 mm min. 7.3 Taping specification 1. Material of the carrier tape shall be A－PET or PS (ESD) 2. The seal tape shall not cover the sprocket holes. And not protrude from the carrier tape. 3. Tensile strength of the tape : 10N or more. 4. The number of lack is 0.1% of 1 reel total part number (the number of the table letters) or the part following whose 1 either is big. (But, the thing which lack of the continuance is not in.) 5. The R of the corner without designation is 0.3R MAX. 6. Misalignment between centers of the cavity and sprocket hole shall be 0.05mm or less. 7. Peeling force of the seal tape (Peeling speed 300mm/min.): 0.1 to 1.0N{10.2 to 71.4gf}. 8. Cumulative pitch error of feed hole : 50 pitch→±0.3mm 9. The marking on parts is not fixed its direction, its electrical characteristic is equal. 160°~180° Seal tape Carrier tape KYOCERA Crystal Device Corporation KBS-5079F Drawing No. UKY1C-H1-14560-00[40] 8/11 7.4 Reel specifications W C D E B Material ：PS A In the case of φ180 Reel (1,000 pcs. Max.) Symbol A Dimension Symbol Dimension B C D φ180 φ60 φ13 φ21 E W 2.0 13.0 (Unit : mm) KYOCERA Crystal Device Corporation KBS-5079F Drawing No. UKY1C-H1-14560-00[40] 9/11 8.Enviromental requirements After following test, frequency shall not change more than ±20×10－６ And CI，±20% or 5Ωof large value. 8.1 Resistance to Shock Test condition Natural dropped from height 75cm onto hard wood board in 3 times 8.2 Resistance to Vibration 8.3 Resistance to Heat Test condition frequency ： 10－55 －10 Hz Amplitude ： 1.5mm Cycle time ： 1 minutes Direction ： X,Y,Z (3direction),2 h each. Test condition The quartz crystal unit shall be stored at a temperature of +85±2°C for 500 h. Then it shal be subjected to standard atmospheric conditions for 1 h ,after whichi measurement shall be made. 8.4 Resistance to Cold Test condition The quartz crystal unit shall be stored at a temperature of －40±2°C for 500 h. Then it shal be subjected to standard atmospheric conditions for 1 h ,after whichi measurement shall be made. 8.5 Thermal Shock Test condition The quartz crystal unit shall be subjected to 10 succesive change of temperature cycles ，each as shown in table below，Then it shall be subjected to standard atmospheric conditions for 1h，after which measurements shall be made. Cycle ：－40±2°C（30min.）to 25±2°C（5min.） to +85±2°C（30min.）to 25±2°C（5min.） KYOCERA Crystal Device Corporation KBS-5079F Drawing No. 8.6 Resistance to Moisture UKY1C-H1-14560-00[40] 10/11 Test condition The quartz crystal unit shall be stored at a temperature of 60±2°C wich relative humidity of 90% to 95% for 500 h. Then it shall be subjected to standard atmospheric conditions for 1h，after which measurements shall be made 8.7 Soldering condition 1.） Material of solder Kind … lead free solder paste Melting point … +220±5°C 2.） Reflow temp.profile Temp [°C] Preheating +150 to +180 Peak +260±5 Total ― Frequency shift : ±2ppm 3.） Hand Soldering +350°C 3 sec MAX 4.） Reflow Times 2 times Time[sec] 150 (typ.) 10 (max.) 300 (max.) Reflow temp.profile 8.8 Intensity for bending in circuit board Solder this product in center of the circuit board of 40mm×100mm， and add the deflection of 3mm as the bottom figure. Test board : t＝1.6mm 20 PUSH 1.6 board 10 R5 Product 45 45 R340 press jig UNIT : mm KYOCERA Crystal Device Corporation KBS-5079F Drawing No. UKY1C-H1-14560-00[40] 11/11 9.Cautions for use （1）Soldering in mounting In case of Solder paste and conductive glue contact product lid or product side face exception for product terminal it’s possible to influence product characteristics. Please be careful above contents. （2）Automatic mounting machine use Please use after affirmation that select the mounting machine model with a shock small if possible in the case of use of an automatic mounting machine, and it does not have breakage. There is a risk of a quartz crystal unit breakage occurring and not functioning normally by too much shock etc.. （3）Conformity of a circuit In case of use of an oscillation circuit, please insert in a quartz crystal unit in series resistance 5 times as many as the standard value of equivalent in-series resistance, and confirm oscillating. Please remove resistance which inserted after the notes above-mentioned examination in the quartz crystal unit in series, and use it. （4）After making the Quartz Crystal mount on a printed circuit board ,if it is required to devide the printed circuit board into another one, use it with attentive confirmation so that a warp cased by this dividing might not affect any damage. When designing a printed circuit board as well as handling the mounting As much as possible. The quartz crystal shall be passed through the reflow furnace. Then it shall be subjected to standard atmospheric conditions, after which cleaning shall be made. 10.Storage conditions Storage at prolonged high temperature or low temperature and the storage by high humidity cause degradation of frequency accuracy, and degradation of soldering nature. Storage is performed at the temperature of 18-30 degrees C, and the humidity of 20-70 Percent in the state of packing, and a term is 6 months. 11. Manufacturing location KYOCERA Crystal Device Philippines, Inc. KYOCERA Crystal Device Corporation 12. Quality Assurance Kyocera Crystal Device Quality Assurance Division 13. Quality guarantee When the failure by the responsibility of our company occurs clearly after delivery within 1 year, a substitute article etc. is appropriated gratuitously and this is guaranteed. However, when passing 1 year after delivery, there is a case where I am allowed to consider as onerous repair after both consultation. 14.Others When any questions and opinions are in the written matter of these delivery specifications, I will ask connection of you from the our company issue day within 45 days. In a connection no case, a written matter is consented to it and employed within a term. KYOCERA Crystal Device Corporation KBS-5079F