KT2520F38400ZAW18TEK

Issued Date : 4, Mar, 2011 Issued No. : K1104-11098-581 Messrs : Digi-Key RoHS Compliant Temperature Compensated Crystal Oscillator ( TCXO ) KT2520F38400ZAW18TEK Technical Specification KYOCERA KINSEKI Corporation (1/6) Revision History Revision No. Revision Date 1 4.Mar.2011 Revision Content and reason The first edition. KYOCERA KINSEKI Prepared By Approved By K.ONO N.NAKANO (2/6) KT2520F Parts Number KT2520F38400ZAW18TEK Z : Freq. Stability VS Temp Special specification A : Bottom Temperature Limit -40 deg.C W : Upper Temperature Limit +85 deg.C 18 : Power Supply Voltage 1.8V T : Specification Number KT2520F Electrical Characteristics Ta= -40deg.C to +85deg.C, Vcc=1.8V, Load 10kohm//10pF Symbol Item Vcc Power Supply Voltage F0 Nominal Frequency Condition Specification Unit 1.8+/-0.1 V 38.400000 MHz Remarks Topr Operating Temperature -40 to +85 deg.C Tstg Storage Temperature -40 to +85 deg.C Vout Output Voltage 0.8(min) Vp-p Icc Power Supply Current 2.0(max) mA f0 Frequency Tolerance +/-2.0(max) ppm Ta=25+/-2deg.C vs Temp -30 to +85deg.C +/-0.5(max) ppm ref.:Ta=25deg.C vs Temp -40 to -30deg.C +/-4.0(max) ppm ref.:Ta=25deg.C +/-0.2(max) ppm vs Voltage 1.8V+/-0.1V +/-0.2(max) ppm Ta=25+/-2deg.C +/-1.0(max) ppm/Y -8.0(max) dBc Preset Frequency and after 2 times reflow df/F Frequency Stability vs Load 10pF+/-10% 10Kohm+/-10% dfag --- Frequency Aging Rate Harmonics KYOCERA KINSEKI One Year (3/6) KT2520F Dimension & Pin Connections & Recommended Land Pattern 2.50±0.15 #5 #4 #1 #2 #3 2.00±0.15 #6 #1 #3 #4 #6 Top View 0.8 max. #1pin Marking GND GND OUT Vcc #2/#5 N.C Unit : mm Side View Land pattern(Reference) #6 #5 #4 0.35 0.65 0.65 #6 #5 #1 #2 #4 0.650 0.650 0.675 0.825 0.43 #3 0.825 #2 0.675 #1 0.35 0.55 0.50 0.50 Bottom View KYOCERA KINSEKI 0.7 1.80 #3 0.55 0.50 (4/6) KT2520F Recommended Circuit ※1 Bypass Capacitor and DC-Blocking Capacitor do not build in this Parts. So, Bypass Capacitor and DC-Blocking Capacitor are attached outside and please use it. And these Capacitor should be ※2 placed as close as possible to the pin(No.4 and No.6). Vcc ※2 OUT ※2 ※1:0.01μF ※1:0.01μF N.C ⑤ ⑥ ④ Top view ① ② ③ N.C GND KT2520F Recommended Reflow Soldering Condition (Lead Free Version) Temp.(deg.C) 300 Soldering Zone 260 +0/-10deg.C 10sec max 250 230deg.C 200 Pre Heating Zone 180+0/-10deg.C 150 120sec max 100 50 normal temperature 0 Heating Time(sec) KYOCERA KINSEKI 40sec max (5/6 ) KT2520F TAPE&REEL SPEC Pull out direction Leader 400∼560mm TOP TAPE 100∼200mm (Empty) Pull out direction 2.00±0.05 4.00±0.1 1.75±0.1 4.00±0.1 φ1.50±00.1 8.00±0.2 3.50±0.05 φ1.00±00.1 2.90±0.05 0.25±0.05 5ﾟ 1.10±0.05 2.40±0.05 5ﾟ Rolling direction Clockwise Tail tape direction 40 pokets Min Tape ending management Adhesive tape fixed on reel (Materials : Carrier Tape PS included Carbon , Cover Tape PET .) Pull out strength 10N Min Tear off strength 0.1N∼0.7N (Speed 300mm/min) φ60 φ180 A (Materials : PS included Carbon.) 3000pcs max. / 1Reel φ180 2000pcs max. ① ② ③ ④ ⑤ ⑥ Reel diameter φ180 Quantity 2000pcs 3000pcs max. / 1Reel Tape width 8mm Tape pitch 4mm Set direction Guide side , Fiducail marking For exclusive label No. KYOCERA KINSEKI A detail 9.0±0.3 φ21±0.8 2.0±0.2 φ13±0.2 Reel Dimensions (6/6 ) KT2520F Notice 1. Please use soldering iron and the spot heater within the range of a solder heat test condition. 2. Units should be stored in a dry environment keeping away from the sun. 3. Don't leave units in high-Temperature and high-humidity environment due to terminal solderability. (Please keep 0℃～40℃ and 30%～70%RH for recommendable storage condition) 4. The term of a guarantee of taping packing is 6 months. (0 deg.C to 40 deg.C,RH30% to 70%) 5. Disapprove of washing. 6. Unless we receive request for modification within 1 month from the issue date of this KKC specification sheet, we will supply products according to this specification. Also, if you’d like to modify specification of order, which has been placed with delivery within 1 month from the issue data of this specification sheet, we would like to discuss with you separately. 7. If you intend to use products listed on this specification for applications that may result in loss of life or assets (controls relating to safety, medical equipment, aeronautical equipment, space equipment, etc.), please do not fail to advise us of your intention beforehand. 8. In no event shall the company be liable for any product failure resulting from an inappropriate. Handling or operation of the product beyond the scope of its guarantee. 9. Information contained in this specification must not be quoted, reproduced or used for other purposes including processing either in part or in full without obtaining prior approval from the company. 10. Moisture sensitivity level MSL=1 KYOCERA KINSEKI