TCG058WXLPBVNN-AN30

Spec No. Date SPEC for Mass Production TQ3C-8EAF0-E1YBK06-00 June 17, 2020 TYPE : TCG058WXLPBVNN-AN30 < 5.8 inch WXGA transmissive color TFT with LED backlight and constant current circuit for LED backlight > CONTENTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Application Construction and outline Mechanical specifications Absolute maximum ratings Electrical characteristics Optical characteristics Interface signals Input timing characteristics Lot number identification Warranty Precautions for use Reliability test data Outline drawing Jun 19, 2020 KYOCERA CORPORATION This specification is subject to change without notice. Consult Kyocera before ordering. Original Issue Date June 17, 2020 Designed by: Engineering dept. Prepared Checked K. Edo M. Iwasaki Confirmed by: QA dept. Approved Checked A. Iwasaki S. Kishimoto Approved O. Sato Spec No. TQ3C-8EAF0-E1YBK06-00 Part No. Page TCG058WXLPBVNN-AN30 Warning 1. This Kyocera LCD module has been specifically designed for use only in electronic devices and industrial machines in the area of audio control, office automation, industrial control, home appliances, etc. The module should not be used in applications where the highest level of safety and reliability are required and module failure or malfunction of such module results in physical harm or loss of life, as well as enormous damage or loss. Such fields of applications include, without limitation, medical, aerospace, communications infrastructure, atomic energy control. Kyocera expressly disclaims any and all liability resulting in any way to the use of the module in such applications. 2. Customer agrees to indemnify, defend and hold Kyocera harmless from and against any and all actions, claims, damages, liabilities, awards, costs, and expenses, including legal expenses, resulting from or arising out of Customer's use, or sale for use, or Kyocera modules in applications. Caution 1. Kyocera shall have the right, which Customer hereby acknowledges, to immediately scrap or destroy tooling for Kyocera modules for which no Purchase Orders have been received from the Customer in a two-year period. - Spec No. Part No. TQ3C-8EAF0-E1YBK06-00 Revision record Designed by : Engineering dept. Prepared Checked Approved Date Rev.No. Date Page TCG058WXLPBVNN-AN30 Confirmed by : QA dept. Checked Approved Descriptions Page - Spec No. Part No. TQ3C-8EAF0-E1YBK06-00 Page TCG058WXLPBVNN-AN30 1 1. Application This document defines the specification of TCG058WXLPBVNN-AN30. (RoHS Compliant) 2. Construction and outline LCD Backlight system Polarizer Interface Additional circuit : Transmissive color dot matrix type TFT : LED : Anti-Glare treatment : LVDS : Timing controller, Power supply (3.3V input) Constant current circuit for LED Backlight(12V input) 3. Mechanical specifications Item Specification Unit 141.29 (W)× 88.5 (H)× 7.49 (D) mm Active area 126.72(W)×74.88(H) (14.7cm/5.8 inch(Diagonal)) mm Dot format 1280×(R,G,B)(W)×768(H) dot Pixel pitch 0.099(W)×0.0975(H) mm Normally Black - 113 g Outline dimensions Base color Mass 1) . 1）Projection not included. Please refer to outline for details. 2）Due to the characteristics of the LCD material, the color varies with environmental temperature. Spec No. Part No. TQ3C-8EAF0-E1YBK06-00 Page TCG058WXLPBVNN-AN30 2 4. Absolute maximum ratings 4-1. Electrical absolute maximum ratings Item Symbol Min. Max. Unit Supply voltage(+3.3V) V DD -0.3 4.0 V Supply voltage(+12V) V IN -0.3 14.0 V V I1 -0.3 2.8 V CK IN+, CK IN- V I2 -0.3 2.8 V SELLVDS, BITSEL, SC V I3 -0.3 V DD +0.5 V BLBRT, BLEN V I4 -0.3 VIN V 1) RxINi+, RxINiInput signal Voltage 2) 1) i=0,1,2,3 2) V DD must be supplied correctly within the range described in 5-1. 4-2. Environmental absolute maximum ratings Item Symbol Min. Max. Unit Operating temperature 1) T OP -20 70 °C Storage temperature 2) T STO -30 80 °C Operating humidity 3) H OP 10 4) %RH Storage humidity 3) H STO 10 4) %RH Vibration - 5) 5) - Shock - 6) 6) - 1) 2) 3) 4) 5) Operating temperature means a temperature which operation shall be guaranteed. Since display performance is evaluated at 25°C, another temperature range should be confirmed. Temp. = -30°C＜48h , Temp. = 80°C＜168h Store LCD at normal temperature/humidity. Keep them free from vibration and shock. An LCD that is kept at a low or a high temperature for a long time can be defective due to other conditions, even if the low or high temperature satisfies the standard. (Please refer to “Precautions for Use” for details.) Non-condensing Temp.≦40°C, 85%RH Max. Temp.＞40°C, Absolute humidity shall be less than 85%RH at 40°C. Frequency 10～55 Hz Vibration width 0.15mm Interval 6） 10-55-10 Hz Acceleration value (0.3～9 m/s2) １minutes 2 hours in each direction X, Y, Z (6 hours total) EIAJ ED-2531 Acceleration: 490 m/s2, Pulse width: 11 ms 3 times in each direction: ±X, ±Y, ±Z EIAJ ED-2531 Spec No. Part No. TQ3C-8EAF0-E1YBK06-00 Page 3 TCG058WXLPBVNN-AN30 5. Electrical characteristics 5-1. LCD Temp. =-20~70℃ Item Symbol Condition Min. Typ. Max. Unit V DD - 3.0 3.3 3.6 V Current consumption I DD 2) - 275 350 mA Permissive input ripple voltage V RP V DD =3.3V - - 100 mVp-p V IL "Low" level 0 - 0.8 V V IH "High" level 2.0 - V DD V I OL V I3 =0V -10 - 10 μA I OH V I3 =3.3V - - 400 μA Supply voltage Input signal voltage 1) 3) Input leak current LVDS Input voltage 4) VL - 0 - 1.9 V Differential input voltage 4) V ID - 100 350 600 mV Differential input threshold voltage 4) 5) V TL "Low" level V CM -100 - - mV V TH "High" level - - V CM +100 mV R1 - - 100 - Ω t1 - 0.1 - 10 ms t2 - 0 - - ms t3 - 0 - - ms t4 - 1.0 - - s t5 - 200 - - ms t6 - 200 - - ms t7 - 0 - 10 s t8 - 0 - - ms Terminator V DD -turn-on conditions 1) V DD -turn-on conditions 1) 6) Spec No. Part No. TQ3C-8EAF0-E1YBK06-00 TCG058WXLPBVNN-AN30 2) Display pattern: V DD = 3.3V, Temp. = 25°C 1 2 3 : : : 767 768 (dot) 123 456 ・・・・・・・・・・・・・・・・ 3838 3839 3840 (dot) □□□□□□□□□□□□□□□□□□□□□□ □□□□□□□□□□□□□□□□□□□□□□ □□□□□□□□□□□□□□□□□□□□□□ □□□□□□□□□□□□□□□□□□□□□□ □□□□□□□□□□□□□□□□□□□□□□ □□□□□□□□□□□□□□□□□□□□□□ □□□□□□□□□□□□□□□□□□□□□□ □□□□□□□□□□□□□□□□□□□□□□ 3) Input signal : SELLVDS, BITSEL, SC 4) Input signal : RxIN3+, RxIN3-, RxIN2+, RxIN2-, RxIN1+, RxIN1-, RxIN0+, RxIN0CK IN+, CK IN- VID VL VCM 0V 5) V CM : LVDS Common mode voltage (V CM =1.25V) 6) Please power on LVDS transmitter at the same time as VDD, or LVDS transmitter should be powered on first. Page 4 Spec No. Part No. TQ3C-8EAF0-E1YBK06-00 Page TCG058WXLPBVNN-AN30 5-2. Constant current circuit for LED Backlight Item Supply voltage 1) Current consumption Permissive input ripple voltage BLBRT Input signal voltage BLBRT Input pull-down resistance BLEN Input signal voltage BLEN Input pull-down resistance PWM Frequency PWM Duty ratio Operating life time 3) 3) 4), 5) 5 Temp. = -20～70°C Symbol Condition Min. Typ. Max. Unit VIN - 11.4 12.0 12.6 V IIN 2) - 135 180 mA VRP_BL VIN=12.0V - - 100 mVp-p VIL_BLBRT "Low" level 0 - 0.4 V VIH_BLBRT "High" level 1.5 - VIN V RIN_BLBRT - - 100 - kΩ VIL_BLEN "Low" level 0 - 0.6 V VIH_BLEN "High" level 1.5 - VIN V RIN_BLEN - - 100 - kΩ fPWM - 200 - 20k Hz fPWM=200Hz 1 - 100 % fPWM=2kHz 1 - 100 % fPWM=20kHz 10 - 100 % Temp.=25°C - 50,000 DPWM T 1) VIN-turn-on conditions 2) VIN = 12V, Temp. = 25℃，DPWM = 100% h Spec No. TQ3C-8EAF0-E1YBK06-00 Part No. TCG058WXLPBVNN-AN30 3) PWM timing diagram tPWM ≧50μs，tON≧5μs (fPWM=1/tPWM) In case of lower frequency, the deterioration of the display quality, flicker etc., may occur. 4) When brightness decrease 50% of minimum brightness. The average life of a LED will decrease when the LCD is operating at higher temperatures. 5) Life time is estimated data. (Condition: D PWM = 100%, Ta=25℃ in chamber). Page 6 Spec No. Part No. TQ3C-8EAF0-E1YBK06-00 Page 7 TCG058WXLPBVNN-AN30 6. Optical characteristics Measuring spot =φ6.0mm, Temp. = 25°C Item Response time Symbol Condition Min. Typ. Max. Unit Rise τr θ=φ=0° － 11 21 ms Down τd θ=φ=0° － 9 19 ms θ UPPER － 85 － θ LOWER － 85 － － 85 － － 85 － Viewing angle range CR≧10 φ LEFT φ RIGHT Contrast ratio Brightness Red Chromaticity coordinates Green Blue White deg. deg. CR θ=φ=0° 700 1000 － - L DPWM = 100% 560 800 － cd/m2 0.560 0.610 0.660 0.310 0.360 0.410 0.285 0.335 0.385 0.520 0.570 0.620 0.100 0.150 0.200 0.080 0.130 0.180 0.260 0.310 0.360 0.285 0.335 0.385 x y x y x y x y θ=φ=0° θ=φ=0° θ=φ=0° θ=φ=0° 6-1. Definition of contrast ratio CR(Contrast ratio) ＝ 6-2. Definition of response time Brightness with all pixels "White" Brightness with all pixels "Black" - Spec No. Part No. TQ3C-8EAF0-E1YBK06-00 Page 8 TCG058WXLPBVNN-AN30 6-3. Definition of viewing angle φ=0° θUPPER +y θ=0° +y θLOWER φLEFT -x +x φRIGHT +x -x -y -y φ direction θ direction 6-4. Brightness measuring point 640×3 384 (dot) 1） (dot) 1) Rating is defined as the white brightness at center of display screen. 2) 5 minutes after LED is turned on. (Ambient Temp.=25℃) Spec No. Part No. TQ3C-8EAF0-E1YBK06-00 Page 9 TCG058WXLPBVNN-AN30 7. Interface signals 7-1. LCD No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Symbol SC BITSEL RxIN3+ RxIN3GND CK IN+ CK INGND RxIN2+ RxIN2GND RxIN1+ RxIN1GND RxIN0+ RxIN0GND SELLVDS VDD VDD Description Scan direction control (High or Open：Normal、Low：Reverse) Bit data select signal (GND or Open: 8bit mode、High: 6bit mode) LVDS receiver signal CH3(+) LVDS receiver signal CH3(-) GND LVDS receiver signal CK(+) LVDS receiver signal CK(-) GND LVDS receiver signal CH2(+) LVDS receiver signal CH2(-) GND LVDS receiver signal CH1(+) LVDS receiver signal CH1(-) GND LVDS receiver signal CH0(+) LVDS receiver signal CH0(-) GND Mode select signal(LVDS Data mapping) +3.3V power supply +3.3V power supply LCD connector Matching connector ：DF19G-20P-1H(54) ：DF19-20S-1C ：DF19G-20S-1C (HIROSE) (HIROSE) (HIROSE) LVDS receiver ： Embedded in ASIC Matching LVDS transmitter ： THC63LVDM83D(THine Electronics) or compatible 1) Scan direction SC : High or Open SC : Low Note 1) LVDS LVDS LVDS LVDS LVDS LVDS LVDS LVDS LVDS LVDS Spec No. Part No. TQ3C-8EAF0-E1YBK06-00 Page TCG058WXLPBVNN-AN30 7-2. LED No Symbol 1 VIN +12V power supply 2 VIN +12V power supply 3 BLBRT PWM signal(Brightness adjustment) 4 BLEN ON/OFF terminal voltage 5 GND GND 6 GND GND LCD connector Matching connector Description ： SM06B-SHLS-TF(LF)(SN) （JST） ： SHLP-06V-S-B （JST） Note 10 Spec No. Part No. TQ3C-8EAF0-E1YBK06-00 TCG058WXLPBVNN-AN30 7-3. Data mapping (6bit input/ 8bit mode) 1) Location of BITSEL，SELLVDS (THC63LVDM83D(THine Electronics) or compatible) Transmitter Pin No. 51 52 54 55 56 3 4 6 7 11 12 14 15 19 20 22 23 24 27 28 30 50 2 8 10 16 18 25 Data TA0 TA1 TA2 TA3 TA4 TA5 TA6 TB0 TB1 TB2 TB3 TB4 TB5 TB6 TC0 TC1 TC2 TC3 TC4 TC5 TC6 TD0 TD1 TD2 TD3 TD4 TD5 TD6 2Pin BITSEL = "L" or OPEN 18Pin SELLVDS = "L" or OPEN BITSEL=L(GND) or OPEN SELLVDS=H(3.3V) DE：DATA ENABLE HS：HSYNC VS：VSYNC － － － － － － － － － － － － － － － － － － － － － － － － － － － － 2Pin BITSEL = "L" or OPEN 18Pin SELLVDS = "H" R0(LSB) R1 R2 R3 R4 R5(MSB) G0(LSB) G1 G2 G3 G4 G5(MSB) B0(LSB) B1 B2 B3 B4 B5(MSB) (HS) (VS) DE GND GND GND GND GND GND GND Page 11 Spec No. TQ3C-8EAF0-E1YBK06-00 2) Block diagram BITSEL=L(GND) or OPEN SELLVDS=H(3.3V) ※SELLVDS,BITSEL signal line has 10kΩ pulldown resister. ※SC signal line has 10kΩ pullup resister. Part No. TCG058WXLPBVNN-AN30 Page 12 Spec No. TQ3C-8EAF0-E1YBK06-00 Part No. TCG058WXLPBVNN-AN30 When using “6-bit Transmitter”, please connect the unused channel of the control IC receiver as described in the diagram below. ※SELLVDS,BITSEL signal line has 10kΩ pulldown resister. ※SC signal line has 10kΩ pullup resister. Page 13 Spec No. TQ3C-8EAF0-E1YBK06-00 Part No. TCG058WXLPBVNN-AN30 7-4. Data mapping (8bit input / 8bit mode) 1) Location of BITSEL,SELLVDS (THC63LVDM83D(THine Electronics) or compatible) Transmitter Pin No. Data 51 TA0 TA1 52 TA2 54 TA3 55 TA4 56 TA5 3 TA6 4 6 TB0 TB1 7 TB2 11 TB3 12 TB4 14 TB5 15 TB6 19 20 TC0 TC1 22 TC2 23 TC3 24 TC4 27 TC5 28 TC6 30 50 TD0 TD1 2 TD2 8 TD3 10 TD4 16 TD5 18 TD6 25 BITSEL=L(GND) or OPEN SELLVDS=L(GND) or OPEN DE：DATA ENABLE HS：HSYNC VS：VSYNC 2Pin BITSEL = "L" or OPEN 18Pin SELLVDS = "L" or OPEN R0(LSB) R1 R2 R3 R4 R5 G0(LSB) G1 G2 G3 G4 G5 B0(LSB) B1 B2 B3 B4 B5 (HS) (VS) DE R6 R7(MSB) G6 G7(MSB) B6 B7(MSB) (NA) 2Pin BITSEL = "L" or OPEN 18Pin SELLVDS = "H" R2 R3 R4 R5 R6 R7(MSB) G2 G3 G4 G5 G6 G7(MSB) B2 B3 B4 B5 B6 B7(MSB) (HS) (VS) DE R0(LSB) R1 G0(LSB) G1 B0(LSB) B1 (NA) Page 14 Spec No. TQ3C-8EAF0-E1YBK06-00 BITSEL=L(GND) or OPEN SELLVDS=H(3.3V) DE：DATA ENABLE HS：HSYNC VS：VSYNC 2) Block diagram BITSEL=L(GND) or OPEN SELLVDS=L(GND) or OPEN ※SELLVDS,BITSEL signal line has 10kΩ pulldown resister. ※SC signal line has 10kΩ pullup resister. Part No. TCG058WXLPBVNN-AN30 Page 15 Spec No. TQ3C-8EAF0-E1YBK06-00 BITSEL=L(GND) or OPEN SELLVDS=H(3.3V) ※SELLVDS,BITSEL signal line has 10kΩ pulldown resister. ※SC signal line has 10kΩ pullup resister. Part No. TCG058WXLPBVNN-AN30 Page 16 Spec No. TQ3C-8EAF0-E1YBK06-00 Part No. TCG058WXLPBVNN-AN30 7-5. Data mapping (6bit input / 6bit mode) 1) Location of BITSEL, SELLVDS (THC63LVDM63D(THine Electronics) or compatible) Transmitter 2Pin BITSEL = "H" 2Pin BITSEL ="H" 18Pin SELLVDS = "L" or OPEN 18Pin SELLVDS = "H" Pin No. Data － R0(LSB) 44 TA0 － TA1 R1 45 － TA2 R2 47 － TA3 R3 48 － TA4 R4 1 － TA5 3 R5(MSB) － TA6 G0(LSB) 4 － G1 6 TB0 － TB1 G2 7 － TB2 G3 9 － TB3 G4 10 － TB4 12 G5(MSB) － TB5 B0(LSB) 13 － TB6 B1 15 － B2 16 TC0 － TC1 B3 18 － TC2 B4 19 － TC3 20 B5(MSB) － TC4 (HS) 22 － TC5 (VS) 23 － TC6 DE 25 BITSEL=H(3.3V) SELLVDS=L(GND) or OPEN DE：DATA ENABLE HS：HSYNC VS：VSYNC Page 17 Spec No. TQ3C-8EAF0-E1YBK06-00 Part No. TCG058WXLPBVNN-AN30 2) Block diagram BITSEL=H(3.3V) SELLVDS=L(GND) or OPEN ※SELLVDS,BITSEL signal line has 10kΩ pulldown resister. ※SC signal line has 10kΩ pullup resister. Page 18 Spec No. Part No. TQ3C-8EAF0-E1YBK06-00 Page TCG058WXLPBVNN-AN30 19 8. Input timing characteristics 8-1. Timing characteristics 1) Item Clock (CK) Frequency Horizontal Period Enable signal (DE) Horizontal display period Vertical Period Vertical display period Refresh rate Symbol Min. Typ. Max. Unit 1/Tc 60.0 71.1 80.0 MHz 1300 1440 1800 Dot 16.25 20.25 - μs 1024 Line 70 － Th Thd Tv 2) 1280 803 Tvd fv Note 823 768 50 60 3) 1) If the display is used under the condition which is out of specifications such as higher clock frequency than specified value, there is a possibility phenomenon such as display error including white display, malfunction and no image may occur. Please use the display under the conditions written in the specification. 2) Please set a clock frequency, a vertical dormant period, and the horizontal dormant period so that the Horizontal Period should not reach less than Min. value. 3) If the refresh rate reach less than Min. value, the deterioration of the display quality, flicker etc., may occur.(fv=1/Tv) Spec No. TQ3C-8EAF0-E1YBK06-00 8-2. Input data signals and display position on the screen Part No. TCG058WXLPBVNN-AN30 Page 20 Spec No. Part No. TQ3C-8EAF0-E1YBK06-00 Page TCG058WXLPBVNN-AN30 21 9. Lot number identification The lot number shall be indicated on the back of the backlight case of each LCD. MADE IN TCG058WXLPBVNN-AN30:□□-□□ ↓ ↓↓ ↓ ① ②③ ④ ↓ ⑤ ↓ ⑥ No① – No⑥ above indicate ① Data matrix (For internal control purpose only) ② Year code ③ Month code ④ Day code ⑤ Version number (Max. 7 characters) ⑥ Country of origin ② Year code: the last digit of the year e.g. In case of 2020, year code: 0 ③ Month code Month Jan. Feb. Mar. Apr. May Jun. Code 1 2 3 4 5 6 Month Jul. Aug. Sep. Oct. Nov. Dec. Code 7 8 9 X Y Z 10. Warranty 10-1. Incoming inspection Please inspect the LCD within one month after your receipt. 10-2. Production warranty Kyocera warrants its LCD’s for a period of 12 months from the ship date. Kyocera shall, by mutual agreement, replace or re-work defective LCD’s that are shown to be Kyocera’s responsibility. Spec No. TQ3C-8EAF0-E1YBK06-00 Part No. Page TCG058WXLPBVNN-AN30 22 11. Precautions for use 11-1. Installation of the LCD 1) A transparent protection plate shall be added to protect the LCD and its polarizer. 2) The LCD shall be installed so that there is no pressure on the LSI chips. 3) The LCD glass shall be installed flat, without twisting or bending. 4) A transparent protection sheet is attached to the polarizer. Please remove the protection film slowly before use, paying attention to static electricity. 11-2. Static electricity 1) Since CMOS ICs are mounted directly onto the LCD glass, protection from static electricity is required. 2) Workers should use body grounding. Operator should wear ground straps. 11-3. LCD operation 1) The LCD shall be operated within the limits specified. Operation at values outside of these limits may shorten life, and/or harm display images. 2) Please select the best display pattern based on your evaluation because flicker, lines or nonuniformity or unevenness can be visible depending on display patterns. 11-4. Storage 1) The LCD shall be stored within the temperature and humidity limits specified. Store in a dark area, and protect the LCD from direct sunlight or fluorescent light. 2) Always store the LCD so that it is free from external pressure onto it. 11-5. Usage 1) DO NOT store in a high humidity environment for extended periods. Polarizer degradation bubbles, and/or peeling off of the polarizer may result. 2) The front polarizer is easily scratched or damaged. Prevent touching it with any hard material, and from being pushed or rubbed. 3) The LCD screen may be cleaned by wiping the screen surface with a soft cloth or cotton pad using a little Ethanol. 4) Water may cause damage or discoloration of the polarizer. Clean condensation or moisture from any source immediately. 5) Always keep the LCD free from condensation during testing. Condensation may permanently spot or stain the polarizer. 6) Do not disassemble LCD because it will result in damage. 7) This Kyocera LCD has been specifically designed for use in general electronic devices, but not for use in a special environment such as usage in an active gas. Hence, when the LCD is supposed to be used in a special environment, evaluate the LCD thoroughly beforehand and do not expose the LCD to chemicals such as an active gas. 8) Please do not use solid-base image pattern for long hours because a temporary afterimage may appear. We recommend using screen saver etc. in cases where a solid-base image pattern must be used. 9) Liquid crystal may leak when the LCD is broken. Be careful not to let the fluid go into your eyes and mouth. In the case the fluid touches your body; rinse it off right away with water and soap. Spec No. Part No. TQ3C-8EAF0-E1YBK06-00 Page TCG058WXLPBVNN-AN30 12. Reliability test data Test item Test condition Test time High temp. atmosphere 80°C 240h Low temp. atmosphere -30 °C 240h High temp. humidity atmosphere 40°C 90% RH 240h Temp. cycle High temp. operation 1) 2) 3) 4) -30°C R.T. 80°C 0.5h 0.5h 0.5h 70 °C 10cycles 500h Judgement Display function Display quality Current consumption Display function Display quality Current consumption Display function Display quality Current consumption Display function Display quality Current consumption Display function Display quality Current consumption : No defect : No defect : No defect : No defect : No defect : No defect : No defect : No defect : No defect : No defect : No defect : No defect : No defect : No defect : No defect Each test item uses a test LCD only once. The tested LCD is not used in any other tests. The LCD is tested in circumstances in which there is no condensation. The reliability test is not an out-going inspection. The result of the reliability test is for your reference purpose only. The reliability test is conducted only to examine the LCD's capability. 23 Spec No. Date TQ3C-8EAF0-E2YBK06-00 June 17, 2020 KYOCERA INSPECTION STANDARD TYPE : TCG058WXLPBVNN-AN30 KYOCERA CORPORATION Original Issue Date June 17, 2020 Designed by : Engineering dept. Prepared Checked K. Edo M. Iwasaki Approved Confirmed by : QA dept. Checked A. Iwasaki S. Kishimoto Approved O. Sato Spec No. Part No. TQ3C-8EAF0-E2YBK06-00 Revision record Designed by : Engineering dept. Date Rev.No. Prepared Date Page Checked Approved Page TCG058WXLPBVNN-AN30 Confirmed by : QA dept. Checked Descriptions Approved - Spec No. Part No. TQ3C-8EAF0-E2YBK06-00 Page TCG058WXLPBVNN-AN30 1 Visuals specification 1) Note Note General 1. Customer identified anomalies not defined within this inspection standard shall be reviewed by Kyocera, and an additional standard shall be determined by mutual consent. 2. This inspection standard about the image quality shall be applied to any defect within the effective active area and shall not be applicable to outside of the area. 3. Definition of Inspection conditions Luminance : 500 Lux min. Inspection distance : 300 mm. Temperature : 25 ± 5℃ Direction : Directly above Dot defect Bright dot defect The dot is constantly “on” when power applied to the inspection LCD, even when all “Black” data sent to the screen. item Inspection tool: 5% Transparency neutral density filter. Count dot: If the dot is visible through the filter. Don’t count dot: If the dot is not visible through the filter. Ｒ Ｇ Ｂ Ｒ Ｇ Ｂ Ｒ Ｇ Ｂ Ｒ Ｇ Ｂ Ｒ Ｇ Ｂ Ｒ Ｇ Ｂ Ｒ Ｇ Ｂ Ｒ Ｇ Ｂ Ｒ Ｇ Ｂ Black dot defect dot defect The dot is constantly “off” when power applied to the LCD, even when all “White” data sent to the screen. Similar size compared to bright dot. White dot Pixel works electrically, however, circular/foreign (Circular/foreign particle makes dot appear to be “on” even when all particle) “Black” data is sent to the screen. Adjacent dot Adjacent dot defect is defined as two or more bright dot defects or black dot defects. Ｒ Ｇ Ｂ Ｒ Ｇ Ｂ Ｒ Ｇ Ｂ Ｒ Ｇ Ｂ Ｒ Ｇ Ｂ Ｒ Ｇ Ｂ Ｒ Ｇ Ｂ Ｒ Ｇ Ｂ Ｒ Ｇ Ｂ dot defect External Bubble, Scratch, Visible operating (all pixels “Black” or “White”) and non inspection Foreign particle operating. (Polarizer, Cell, Backlight) Appearance inspection Definition Does not satisfy the value at the spec. Definition of circle size of size a: major axis, b: minor axis ｄ＝(ａ＋ｂ)/2 Definition of linear size Spec No. Part No. TQ3C-8EAF0-E2YBK06-00 Page TCG058WXLPBVNN-AN30 2 2) Standard Classification Defect Dot (in LCD defect glass) Inspection item Bright dot defect Acceptable number :4 Bright dot spacing : 5 mm or more Acceptable number :5 Black dot spacing : 5 mm or more Acceptable number :2 Acceptable number :3 3 or more dots join Acceptable number :0 Total dot defects Acceptable number : 5 Max Black dot defect 2 dot join Bright dot defect Black dot defect Others White dot, Dark dot (Circle) External inspection Judgement standard Polarizer (Scratch) (Defect on Polarizer or Size (mm) 0.2 ＜ d ≦ 0.2 0.2 ＜ d ≦ 0.4 0.4 ＜ d ≦ 0.5 0.5 ＜ d ≦ 0.4 Width (mm) 0.1 ＜ W ≦ 0.1 0.1 ＜ W ≦ 0.3 between Polarizer and LCD glass) 0.3 ＜ W ≦ 0.3 Polarizer (Bubble) Foreign particle （Circular shape） Foreign particle （Linear shape） Scratch Acceptable number (Neglected) 5 3 0 Length (mm) － 2.0 ＜ L ≦ 5.0 5.0 ＜ L ≦ 5.0 － Acceptable number (Neglected) (Neglected) 0 0 Size (mm) 0.2 ＜ d ≦ 0.2 0.2 ＜ d ≦ 0.3 0.3 ＜ d ≦ 0.5 0.5 ＜ d ≦ 0.4 Acceptable number (Neglected) 5 3 0 Size (mm) 0.2 ＜ d ≦ 0.2 0.2 ＜ d ≦ 0.4 0.4 ＜ d ≦ 0.5 0.5 ＜ d ≦0 .4 Acceptable number (Neglected) 5 3 0 Width (mm) 0.00 ＜ W ≦ 0.03 0.03 ＜ W ≦ 0.10 0.1 ＜ W ≦0.3 Length (mm) － 2.0 ＜ L ≦ 2.0 2.0 ＜ L ≦ 4.0 4.0 ＜ L ≦ 5.0 － Acceptable number (Neglected) (Neglected) 3 0 (According to circular shape) Color variation Not to be significantly visible. （Mura） Consultation shall be held as necessary.