TVL-55736GD032JR-LW-G-AAN

R RooH HS S C CO OM MP PLLIIA AN NT T APPROVAL SHEET 承 認 書 Customer 客戶名稱 Part No. 產品型號 Product type 產品內容 RoHS 綠色產品 TVL-55736GD032JR-LW-G-AAN Mode: Transmissive and Normally white type 3.2” TFT LCD module □ Non-compliance ■ Compliance Remarks 備註欄 ■Preliminary Specification 暫行規格 □Final Specification 正式規格 Signature by Customer: 客戶確認簽章: Issued by QA Checked by QA TVL-55736GD032JR-LW-G-AAN ver.B Checked by PM -1- Approved By QA RD Issue Date: 2013/02/21 R RooH HS S C CO OM MP PLLIIA AN NT T Specification of LCD Module Product No.: TVL-55736GD032JR-LW-G-AAN Issue date: 2013/02/21 KYOCERA DISPLAY CORPORATION 5-7-18 Higashinippori Arakawa-ku Tokyo Japan TEL: +81-03-5811-8772(Direct) FAX: +81-03-5811-8787 TVL-55736GD032JR-LW-G-AAN ver.B -2- Issue Date: 2013/02/21 R RooH HS S C CO OM MP PLLIIA AN NT T TABLE OF CONTENTS 1. GENERAL DESCRIPTION .................................................................5 2. FEATURES.........................................................................................5 3. MECHANICAL SPECIFICATION ........................................................5 4. MECHANICAL DIMENSION ...............................................................6 5. MAXIMUM RATINGS..........................................................................7 6. ELECTRICAL CHARACTERISTIC .....................................................7 6.1. DC Characteristics.......................................................................................... 7 6.2. Backlight Characteristics ................................................................................ 8 7. MODULE FUNCTION DESCRIPTION ................................................9 7.1. 7.2. 7.3. 7.4. 7.5. 7.6. PIN DESCRIPTION ........................................................................................ 9 i80/16-bit System Bus Interface Timing Characteristics ............................... 10 i80/16-bit System interface ........................................................................... 11 i80/16-bit System Bus Interface Timing(Register) ........................................ 11 i80/16-bit System Bus Interface Timing(GRAM) ........................................... 12 Reset Timing Characteristics........................................................................ 12 8. ELECTRO-OPTICAL CHARACTERISTICS......................................13 8.1. 8.2. Optical characteristics................................................................................... 13 CIE(x, y) chromaticity.................................................................................... 13 9. RELIABILITY ....................................................................................15 9.1. 9.2. 9.3. 10. MTTF ............................................................................................................ 15 Tests............................................................................................................. 15 Color performance ........................................................................................ 15 INSPECTION CRITERIA................................................................16 10.1. 10.2. 10.3. 10.4. Inspection Conditions................................................................................ 16 Light Method ............................................................................................. 16 Classification Of Defects ........................................................................... 16 Sampling & Acceptable Quality Level ....................................................... 17 10.5. Definition Of Inspection Area .................................................................... 17 TVL-55736GD032JR-LW-G-AAN ver.B -3- Issue Date: 2013/02/21 R RooH HS S C CO OM MP PLLIIA AN NT T 10.6. Items and Criteria...................................................................................... 18 11. ILLUSTRATION OF LCD DATE CODE .........................................21 12. ROHS COMPLIANT WARRANTY .................................................21 13. PRECAUTIONS FOR USE ............................................................21 13.1. Safety........................................................................................................ 21 13.2. 13.3. Storage Conditions.................................................................................... 21 Installing LCD Module ............................................................................... 21 13.4. 13.5. Precautions For Operation ........................................................................ 22 Handling Precautions ................................................................................ 22 13.6. Guarantee ................................................................................................. 23 14. REVISION HISTORY .....................................................................23 TVL-55736GD032JR-LW-G-AAN ver.B -4- Issue Date: 2013/02/21 R RooH HS S C CO OM MP PLLIIA AN NT T 1. GENERAL DESCRIPTION TVL-55736GD032JR-LW-G-AAN is a Transmissive type color active matrix liquid crystal display (LCD), which uses amorphous thin film transistor (TFT) as switching devices. This product is composed of a TFT LCD panel, driver ICs, FPC and a backlight unit. The following table described the features of TVL-55736GD032JR-LW-G-AAN. 2. FEATURES Display Mode Transmissive Type 3.2” TFT LCD, Normally white type Display Format RGB vertical stripe Driver IC. ILI 9325C Interface 8080 - system 16 bit Interface Viewing Direction Higher Contrast ratio: 9 o’clock Less gray scale reversal: 3 o’clock Backlight type / color LED / white *5 3. MECHANICAL SPECIFICATION Item Specifications Unit 55.14(W)×78(H)×2.9(D)* mm Resolution 240×3(R,G,B)×320 dot Active area 48.6(W)×64.8(H) mm Pixel pitch 0.2025(W)×0.2025(H) mm Dimensional outline ＊ Without FPC TVL-55736GD032JR-LW-G-AAN ver.B -5- Issue Date: 2013/02/21 TVL-55736GD032JR-LW-G-AAN ver.B -6- DISPLAY SCALE 40/1 RGB 40 1 View Direction 240(R.G.B)X320 DOTS SINGLE SIDE AREA CONDUCTIVE PEELING TAPE 1 40 GIANTPLUS TECHNOLOGY CO.,LTD MYLAR TAPE (Amber) ※ Silicone applied to cover trace ,and IC COMPONENT AREA (H=1.0 MAX.) STIFFENER PRINTING LINE REFLECTOR R RooH HS S C CO OM MP PLLIIA AN NT T 4. MECHANICAL DIMENSION Issue Date: 2013/02/21 R RooH HS S C CO OM MP PLLIIA AN NT T 5. MAXIMUM RATINGS ITEM SYMBOL MIN. MAX. UNIT Power Supply Voltage VCC 2.5 3.3 V Logic input voltage range VCC-GND 2.4 3.3 Operation Temperature Top -20 70 V ℃ Storage Temperature Tstg -30 80 ℃ - 90 %RH Humidity Note 1: TA≦40℃ Without dewing Note Note1 6. ELECTRICAL CHARACTERISTIC 6.1. DC Characteristics (VCC = 2.4~3.3V,IOVCC=1.65~3.3V) Item Symbol IC Power Voltage Values Unit Min. Typ. Max. VCC 2.5 2.8 3.3 V Consumption current of VCC ICC - 9.5 16 mA Low Level Input Voltage VIL -0.3 - 0.2 x IOVCC V High Level Input Voltage VIH 0.8 x IOVCC - IOVCC V Low Level Output Voltage VOL - - 0.2 x IOVCC V High Level Output Voltage VOH 0.8 x IOVCC - - V TVL-55736GD032JR-LW-G-AAN ver.B -7- Issue Date: 2013/02/21 R RooH HS S C CO OM MP PLLIIA AN NT T 6.2. Backlight Characteristics Item Symbol Condition Min Typ. Max. Unit LED module Forward voltage VLED ILED=20mA --- 17.5 --- V LED module current ILED VLED=17.5V --- 20 --- mA LD ILED=20mA VLED=17.5V --- 80 --- % Surface brightness uniform （without LCD） ★ 1 Backlight LED Circuit： LED20mA LED+ ★2 Uniform measure condition： (a)Measure 9 point. Measure location is show below： (b)Uniform = (Min. brightness / Max. brightness)×100% (c)Best Contrast, Main and sub panel All dots turn ON (White screen) 2W/3 W/3 2H/3 ○ 1 ○ 2 ○ 3 ○ 4 ○ 5 ○ 6 ○ 7 ○ 8 ○ 9 Active area (H) H/3 Active area TVL-55736GD032JR-LW-G-AAN ver.B -8- Issue Date: 2013/02/21 R RooH HS S C CO OM MP PLLIIA AN NT T 7. MODULE FUNCTION DESCRIPTION 7.1. PIN DESCRIPTION Pin NO. Symbol 1 VCC 2 VCI 3 CS 4 5 6 7 8 9 ~16 17 Function A supply voltage to the internal logic：Vcc = 2.4~3.3V A supply voltage to the analog circuit. Connect to an external power supply of 2.5~3.3V A chip select signal. Low：the ILI9325C is selected and accessible High：the ILI9325C is not selected and not accessible。 Fix to the GND level when not in use A register select signal. DNC_SCL/RS Low：select an index or status register High：select a control register A write strobe signal and enables WR an operation to write data when the signal is low A read strobe signal and enables RD an operation to read data when the signal is low A reset pin. /RESET Initializes the ILI9325C with a low input。 Be sure to execute a power-on reset after supplying power NC No Connect DB1 ~ DB8 Data bus pin NC No Connect 18~25 DB10~DB17 26~38 GND Data bus pin Power ground。GND=0V。 39 LED + B/L power supply 40 LED - B/L power ground TVL-55736GD032JR-LW-G-AAN ver.B -9- Issue Date: 2013/02/21 R RooH HS S C CO OM MP PLLIIA AN NT T 7.2. i80/16-bit System Bus Interface Timing Characteristics Normal write mode (IOVCC=1.65V~3.30V, VCC=2.4V~3.30V), TVL-55736GD032JR-LW-G-AAN ver.B - 10 - Issue Date: 2013/02/21 R RooH HS S C CO OM MP PLLIIA AN NT T 7.3. i80/16-bit System interface 7.4. i80/16-bit System Bus Interface Timing(Register) (a) Write to Register (b) Read to Register TVL-55736GD032JR-LW-G-AAN ver.B - 11 - Issue Date: 2013/02/21 R RooH HS S C CO OM MP PLLIIA AN NT T 7.5. i80/16-bit System Bus Interface Timing(GRAM) (a) Write to Register (b) Read to Register 7.6. Reset Timing Characteristics TVL-55736GD032JR-LW-G-AAN ver.B - 12 - Issue Date: 2013/02/21 R RooH HS S C CO OM MP PLLIIA AN NT T 8. ELECTRO-OPTICAL CHARACTERISTICS 8.1. Optical characteristics Item Symbol Temp. Min. Typ. Max. Unit Conditions Tr 25℃ - 11 12 ms Tf 25℃ - 14 18 ms Luminance L 25℃ 220 250 - cd/m2 - Contrast ratio CR 25℃ 230 250 - - NOTE 1 50 60 - 50 60 - Degree NOTE 2 30 50 - 50 60 - Degree NOTE 2 Response time Viewing Angle 8.2. Item Vertical Horizontal NOTE 3 θ+ 25℃ θΨ+ 25℃ Ψ- CIE(x, y) chromaticity Transmissive Symbol Conditions Min. Typ. Max. X - 0.634 - y - 0.348 - X - 0.364 - y - 0.559 - X - 0.144 - Red Green θ=0° , ψ=0° θ=0° , ψ=0° θ=0° , ψ=0° Blue y - 0.086 - X - 0.292 θ=0° , ψ=0° White y - TVL-55736GD032JR-LW-G-AAN ver.B 0.299 - - 13 - Issue Date: 2013/02/21 R RooH HS S C CO OM MP PLLIIA AN NT T NOTE 1: Definition of contrast ratio: Measure contrast ratio on the below 5 points and take average value。 Contrast ratio is calculated with the following formula: Contrast Ratio（CR）＝（White）Luminance of ON÷（Black）Luminance of OFF NOTE 2: Definition of Viewing Angle（θ，Ψ） NOTE 3: Definition of Response Time The response time is defined as the time interval between the 10﹪and 90﹪ amplitudes。 TVL-55736GD032JR-LW-G-AAN ver.B - 14 - Issue Date: 2013/02/21 R RooH HS S C CO OM MP PLLIIA AN NT T 9. RELIABILITY 9.1. MTTF The LCD module shall be designed to meet a minimum MTTF value of 50,000 hours with normal condition. (25°C in the room without sunlight; not include life time of backlight) 9.2. Tests NO. 1 2 ITEM High Temperature Operating Low Temperature Operating CONDITION 70℃ -20℃ 3 High Temperature Non-Operating 80℃ 4 Low Temperature Non-Operating -30℃ 5 240 hrs CRITERION 。No Defect Of Operational Function In Room Temperature Are Allowable(23±5°C). 240 hrs 240 hrs 。Leakage current should be below double of initial value. 240 hrs High Temperature/ 50℃ ,90%RH 240 hrs Humidity Non-Operating -30℃ 80℃ Temperature Shock 6 Non-Operating ( 30min ) ( 30min ) 10 CYCLES Electrostatic Discharge HBM:±2KV Test Non-Operating Note 1: Test after 24 hours in room temperature(23±5°C). Note 2: The sampling above is individually for each reliability testing condition. Note 3: The color fading of polarizing filter should not care. Note 4: All of the reliability testing chamber above, is using D.I. water.(Min value: 1.0 MΩ -cm) Note 5: In case of malfunction defect caused by ESD damage, if it would be recovered to normal state after resetting, it would be judged as a good part. 7 9.3. Color performance No. ITEM Criterion (initial) 1 Luminance >50% 2 NTSC >70% 3 Contrast Ratio >50% TVL-55736GD032JR-LW-G-AAN ver.B - 15 - Issue Date: 2013/02/21 R RooH HS S C CO OM MP PLLIIA AN NT T 10. INSPECTION CRITERIA 10.1. Inspection Conditions 10.1.1. Environmental conditions The environmental conditions for inspection shall be as follows Room temperature: 23±5°C Humidity: 50±20%RH 10.1.2. The external visual inspection With a single 1000±200lux fluorescent lamp as the light source, the inspection was in the distance of 30cm or more from the LCD to the inspector’s eyes. 10.2. Light Method 10.2.1. Environment lamp under 1000±200 lux, Viewing direction for inspection over 30 ㎝ 10.2.2. The distance from eye to defect around 300mm, the distance from ND Filter to defect around 25~30mm Eye 300mm ND Filter Defect place 10.3. Classification Of Defects 10.3.1. Major defect A major defect refers to a defect that may substantially degrade usability for product applications. TVL-55736GD032JR-LW-G-AAN ver.B - 16 - Issue Date: 2013/02/21 R RooH HS S C CO OM MP PLLIIA AN NT T 10.3.2. Minor defect A minor defect refers to a defect which is not considered to be able substantially degrade the product application or a defect that deviates from existing standards almost unrelated to the effective use of the product or its operation. Notes: If the LCD/LCM ’s cosmetic and display performance do not specify in “inspection criterion”, it should be based on these delivered samples. 10.4. Sampling & Acceptable Quality Level Level II, MIL-STD-105E Major Minor Cosmetic 1.0 % 1.5 % Electrical-display 0.4% 0.65 % 10.5. Definition Of Inspection Area V.A: Viewing Area A.A: Active Area Active Area Viewing Area Outside of Viewing area TVL-55736GD032JR-LW-G-AAN ver.B - 17 - Issue Date: 2013/02/21 R RooH HS S C CO OM MP PLLIIA AN NT T 10.6. Items and Criteria 10.6.1. Visual inspection criterion in cosmetic (1) Glass defect No Defect Dimension Criteria Remark By engineering diagram (Minor) Y Z 1 X Extensive crack 【Reject】 Cracks 2 (Major) (2) LCM appearance defect No Defect Criteria Round type Remark Permissible Qty 1.ψ =(L+W)/2, Spec. (Minor) ψ ≦ 0.10mm 1 Disregard 0.10mm