Platinum DRAGON® white with Chip Level Conversion (CLC) Lead (Pb) Free Product - RoHS Compliant LW W5SN
Released
Besondere Merkmale • Gehäusetyp: weißes SMD Gehäuse, klarer Silikon - Verguss, Chip level conversion • Typischer Lichtfluss: 75 lm bei 700 mA • Besonderheit des Bauteils: hocheffiziente Lichtquelle bei geringem Platzbedarf • Farbort: x = 0,33, y = 0,33 nach CIE 1931 (weiß) • typische Farbtemperatur: 5600 K • Farbwiedergabeindex: 80 • Abstrahlwinkel: Lambertscher Strahler (120°) • Technologie: ThinGaN® • optischer Wirkungsgrad: 30 lm/W • Gruppierungsparameter: Lichtstrom, Farbort • Verarbeitungsmethode: für alle SMT-Bestücktechniken geeignet • Lötmethode: IR Reflow Löten • Vorbehandlung: nach JEDEC Level 2 • Gurtung: 24-mm Gurt mit 800/Rolle, ø180 mm • ESD-Festigkeit: ESD-sicher bis 2 kV nach JESD22-A114-D Features • package: white SMD package, colorless clear silicone resin; chip level conversion • typical Luminous Flux: 75 lm at 700 mA • feature of the device: high efficient lightsource at low space • color coordinates: x = 0.33, y = 0.33 acc. to CIE 1931 (white) • typ. color temperature: 5600 K • color reproduction index: 80 • viewing angle: Lambertian Emitter (120°) • technology: ThinGaN® • optical efficiency: 30 lm/W • grouping parameter: luminous flux, color coordinates • assembly methods: suitable for all SMT assembly methods • soldering methods: IR reflow soldering • preconditioning: acc. to JEDEC Level 2 • taping: 24 mm tape with 800/reel, ø180 mm • ESD-withstand voltage: up to 2 kV acc. to JESD22-A114-D
Applications • exterior and interior automotive lighting (e.g. front light) • Flashlight • backlighting (illuminated advertising, general lighting) • reading lamps (aircraft, car, bus) • substitution of micro incandescent lamps • indoor and outdoor commercial and residential architectural lighting • display backlight where high brightness is required e.g. TFT • decorative and entertainment lighting • signal and symbol luminaire for orientation • marker lights (e.g. steps, exit ways, etc.)
1
Anwendungen • Außen- und Innenbeleuchtung im Automobilbereich (z.B. Scheinwerfer) • Blitzlicht • Hinterleuchtung (Werbebeleuchtung, Allgemeinbeleuchtung) • Leselampen (Flugzeug, Auto, Bus) • Ersatz von Kleinst-Glühlampen • Fassadenbeleuchtung im Innen- und Außenbereich • Display Hinterleuchtung mit hohem Helligkeitsbedarf z. B. TFT • Dekorative Beleuchtung • Signal- und Symbolleuchten zur Orientierung • Markierungsbeleuchtung (Stufen, Fluchtwege, u.ä.)
2007-08-16
LW W5SN
Bestellinformation Ordering Information Typ Emissionsfarbe Color of Emission Lichtstrom1) Seite 18 Lichtstärke2) Seite 18 Bestellnummer
Type
Luminous Flux1) page 18 IF = 700 mA ΦV (mlm)
Luminous Intensity2) page 18 IF = 700 mA IV (mcd) 27000 (typ.)
Ordering Code
LW W5SN-JYKZ-5K8L
white
52000 ... 112000
Q65110A5557
Anm.: Die oben genannten Typbezeichnungen umfassen die bestellbaren Selektionen. Diese bestehen aus wenigen Helligkeitsgruppen (siehe Seite 6 für nähere Informationen). Es wird nur eine einzige Helligkeitsgruppe pro Gurt geliefert. Z.B.: LW W5SN-JYKZ-5K8L bedeutet, dass auf dem Gurt nur eine der Helligkeitsgruppen JY, JZ, KX, KY oder KZ enthalten ist. Um die Liefersicherheit zu gewährleisten, können einzelne Helligkeitsgruppen nicht bestellt werden. Gleiches gilt für die Farben, bei denen Farbortgruppen gemessen und gruppiert werden. Pro Gurt wird nur eine Farbortgruppe geliefert. Z.B.: LW W5SN-JYKZ-5K8L bedeutet, dass auf dem Gurt nur eine der Farbortgruppen -5K, -5L, -6K, -6L, -7K, -7L, -8K oder -8L enthalten ist (siehe Seite 5 für nähere Information). Um die Liefersicherheit zu gewährleisten, können einzelne Farbortgruppen nicht bestellt werden. Note: The above Type Numbers represent the order groups which include only a few brightness groups (see page 6 for explanation). Only one group will be shipped on each reel (there will be no mixing of two groups on each reel). E.g. LW W5SN-JYKZ-5K8L means that only one group JY, JZ, KX, KY or KZ will be shippable for any one reel. In order to ensure availability, single brightness groups will not be orderable. In a similar manner for colors where chromaticity coordinate groups are measured and binned, single chromaticity coordinate groups will be shipped on any one reel. E.g. LW W5SN-JYKZ-5K8L means that only 1 chromaticity coordinate group -5K, -5L, -6K, -6L, -7K, -7L, -8K or -8L will be shippable on each reel (see page 5 for explanation). In order to ensure availability, single chromaticity coordinate groups will not be orderable.
2007-08-16
2
LW W5SN
Grenzwerte Maximum Ratings Bezeichnung Parameter Betriebstemperatur Operating temperature range Lagertemperatur Storage temperature range Sperrschichttemperatur Junction temperature Sperrschichttemperatur Junction temperature Durchlassstrom Forward current (TA=25°C) Stoßstrom Surge current t ≤ 10 μs, D = 0.005, TA=25°C Sperrspannung Reverse voltage (TA=25°C) Leistungsaufnahme Power consumption (TA=25°C) Wärmewiderstand4) Seite 18 Thermal resistance4) page 18 Sperrschicht/Lötpad Junction/solder point Symbol Symbol Wert Value – 40 … + 125 – 40 … + 125 Einheit Unit °C °C
Top Tstg Tj Tj
(min.) IF (max.) IF
>150 for short °C term applications 125 100 1000 2500 °C mA mA mA
IFM
VR
not designed for V reverse operation 4.6 W
Ptot
Rth JS
11
K/W
2007-08-16
3
LW W5SN
Kennwerte Characteristics (TA = 25 °C) Bezeichnung Parameter Farbkoordinate x nach CIE 19315) Seite 18 (typ.) 5) page 18 Chromaticity coordinate x acc. to CIE 1931 IF = 700 mA Farbkoordinate y nach CIE 19315) Seite 18 (typ.) 5) page 18 Chromaticity coordinate y acc. to CIE 1931 IF = 700 mA Abstrahlwinkel bei 50 % ΙV (Vollwinkel) Viewing angle at 50 % ΙV Durchlassspannung 6 Seite 18) Forward voltage6) page 18 IF = 700 mA Sperrstrom Reverse current Temperaturkoeffizient von VF Temperature coefficient of VF IF = 700 mA; –10°C ≤ T ≤ 100°C Optischer Wirkungsgrad Optical efficiency IF = 700 mA (typ.) (min.) (typ.) (max.) (max.) (typ.) Symbol Symbol x Wert Value 0.33 Einheit Unit –
y
0.33
–
2ϕ
120 2.9 3.6 4.3
Grad deg. V V V
VF VF VF IR TCV ηopt
not designed for reverse operation μA –4.5 mV/K
(typ.)
30
lm/W
2007-08-16
4
LW W5SN
Farbortgruppen5) Seite 18 5) page 18 Chromaticity coordinate groups
0.42 0.41 0.40 Cy 0.39 0.38 0.37 0.36 0.35 0.34 0.33 0.32 0.31 0.30 0.29 0.28 0.27 0.26 0.25 0.24 0.23 0.22 0.21 0.20
0.9 520 0.8 Cy 0.7 0.6 500 0.5 0.4 0.3 0.2 0.1 0 0 580 590 600 610 620 630 510 530 540 550 560 570
8L 8K 7L
6L 6K 5L 5K
+
7K
+
490 480 470 460 450 0.1 0.2 0.3 0.4 0.5
E
0.6
0.7 Cx
0.8
0.9
Gruppe Group 5K
Cx 0.296 0.291 0.310 0.313
Cy 0.259 0.268 0.297 0.284 0.268 0.279 0.312 0.297 0.284 0.297 0.330 0.310 0.297 0.312 0.347 0.330
Gruppe Group 7K
5L
0.291 0.285 0.307 0.310
7L
6K
0.313 0.310 0.330 0.330
8K
6L
0.310 0.307 0.330 0.330
8L
2007-08-16
5
0.25 0.26 0.27 0.28 0.29 0.30 0.31 0.32 0.33 0.34 0.35 0.36 0.37
Cx
OHA13327
Cx 0.330 0.330 0.338 0.352 0.330 0.330 0.347 0.345 0.352 0.338 0.364 0.360 0.345 0.347 0.367 0.364 Cy 0.310 0.330 0.342 0.344 0.330 0.347 0.371 0.352 0.344 0.342 0.380 0.357 0.352 0.371 0.401 0.380
LW W5SN
Helligkeits-Gruppierungsschema Brightness Groups Helligkeitsgruppe Brightness Group JY JZ KX KY KZ Lichtstrom1) Seite 18 Luminous Flux1) page 18 ΦV (mlm) 52000 ... 61000 61000 ... 71000 71000 ... 82000 82000 ... 97000 97000 ... 112000 Lichtstärke2) Seite 18 Luminous Intensity2) page 18 IV (mcd) 18000 (typ.) 22000 (typ.) 25500 (typ.) 30000 (typ.) 35000 (typ.)
Anm.: Die Standardlieferform von Serientypen beinhaltet eine Familiengruppe. Diese besteht aus 5 Helligkeitsgruppen. Einzelne Helligkeitsgruppen sind nicht bestellbar. Note: The standard shipping format for serial types includes a family group of 5 individual brightness groups. Individual brightness groups cannot be ordered. Gruppenbezeichnung auf Etikett Group Name on Label Beispiel: JZ-6K Example: JZ-6K Helligkeitsgruppe Brightness Group JZ Farbortgruppe Chromaticity Coordinate Group 6K
Anm.: In einer Verpackungseinheit / Gurt ist immer nur eine Helligkeitsgruppe enthalten. Note: No packing unit / tape ever contains more than one brightness group.
2007-08-16
6
LW W5SN
Relative spektrale Emission2) Seite 18 Relative Spectral Emission2) page 18 V(λ) = spektrale Augenempfindlichkeit / Standard eye response curve Φrel = f (λ); TA = 25 °C; IF = 700 mA
100 %
OHL12811
Φrel
80
Vλ
60
40
20
0 400
450
500
550
600
650
700
750
nm 800
λ
Abstrahlcharakteristik2) Seite 18 Radiation Characteristic2) page 18 Ιrel = f (ϕ); TA = 25 °C
40˚ 30˚ 20˚ 10˚ 0˚
OHL01660
ϕ
1.0
50˚
0.8
0.6 60˚ 0.4 70˚ 0.2 80˚ 90˚ 100˚ 1.0
2007-08-16
0
0.8
0.6
0.4
0˚
7
20˚
40˚
60˚
80˚
100˚
120˚
LW W5SN
Durchlassstrom2) Seite 18 Forward Current2) page 18 IF = f (VF); TA = 25 °C
10 3 mA 5
OHL02520
Relative Lichtstrom2) 7) Seite 18 Relative Luminous Flux2) 7) page 18 ΦV/ΦV(700 mA) = f (IF); TA = 25 °C
IF
ΦV Φ V (700 mA)
10 0
2
OHL02688
10 2 5
5
10 1 2.0
2.5
3.0
3.5
4.0 V 4.5
10 -1 10 1
5
10 2
mA 10 3
VF
Farbortverschiebung2) Seite 15 Chromaticity Coordinate Shift2) page 15 x, y = f (IF); TA = 25 °C
0.05 Δ Cx, Δ Cy
OHL02806
IF
Farbortverschiebung2) Seite 15 Chromaticity Coordinate Shift2) page 15 x, y = f (Tj); IF = 700 mA
0.010 Δ Cx, Δ Cy 0.006
OHL02809
0.03 Cy 0.02 0.01 0 -0.01 Cx
0.004 0.002 0 -0.002 -0.004 -0.006 -0.008 -0.010
-0.02
0
200 400 600 800
mA 1200
-0.012 -60 -40 -20 0
20 40 60 ˚C 100
IF
2007-08-16 8
Tj
LW W5SN
Relative Vorwärtsspannung2) Seite 15 Relative Forward Voltage2) page 15 ΔVF = VF - VF(25 °C)= f(Tj); IF= 700 mA
0.4 V
OHL02808
Relative Lichtstrom2) Seite 15 Relative Luminous Flux2) page 15 ΦV/ΦV(25 °C) = f (Tj); IF = 700 mA
1.4
OHL12725
ΔVF
0.2 0.1 0 -0.1 -0.2 -0.3 -60 -40 -20 0
ΦV (25 ˚C)
1.0 0.8 0.6 0.4 0.2 0 -60 -40 -20 0
ΦV
20 40 60 ˚C 100
20 40 60
˚C 100
Tj
Tj
2007-08-16
9
LW W5SN
Maximal zulässiger Durchlassstrom Max. Permissible Forward Current I F = f ( TS ) Exemplarische durchschnittliche2) Seite 18 Lebensdauer für mittlere Helligkeitsgruppe Exemplary median Lifetime2) page 18 for median Brightness Group Bedingungen mittlere Lebensdauer Conditions median Lifetime
IF = 500 mA TS = 25°C IF = 700 mA TS = 85°C 25.000 11.000
IF
1100 mA 900 800 700 600 500 400 300 200 100
OHL02948
Einheit Unit
Betriebsstunden operating hours Betriebsstunden operating hours
*The emitter die exhibits excellent performance but slight package discoloration occurs at highest temperatures.The median lifetime depends on the application
Do not use current below 100 mA 0 0 20 40 60 80 100 ˚C 140
T
Zulässige Impulsbelastbarkeit IF = f (tp) Permissible Pulse Handling Capability Duty cycle D = parameter, TS = 25 °C
3.0 IF A 2.5
OHL03993
Zulässige Impulsbelastbarkeit IF = f (tp) Permissible Pulse Handling Capability Duty cycle D = parameter, TS = 85 °C
3.0 IF A 2.5
OHL03994
D= T
tP
tP
IF T
D = TP
t
tP
IF T
D=
2.0 0.005 0.01 0.02 0.033 0.05 0.1
2.0
D=
0.005 0.01 0.02 0.033 0.05 0.1 0.2 0.5 1
1.5
0.2 0.5
1.5
1.0
1
1.0
0.5
0.5
0 -5 10 10-4 10-3 10-2 10-1 100 101 s 102
0 -5 10 10-4 10-3 10-2 10-1 100 101 s 102
tp
2007-08-16 10
tp
LW W5SN
Maßzeichnung8) Seite 18 Package Outlines8) page 18
0...0.1 (0.004) 6.2 (0.244) 5.8 (0.228)
0.29 (0.011) 0.24 (0.009)
0.8 (0.031) (ø4.2 (0.165))
A Heat sink Protection Diode
5.35 (0.210) 5.25 (0.206)
4.25 (0.167) 4.15 (0.163) ø0.81 (0.031) ø0.73 (0.028)
0.65 (0.026) 0.45 (0.018)
7.2 (0.283)
1.9 (0.075) C 1.7 (0.067)
Cathode
1.1 (0.043) 0.9 (0.035) 2.0 (0.079) 1.6 (0.063)
GPLY6147
Kathodenkennung: Cathode mark: Gewicht / Approx. weight: Gurtung / Polarität und Lage8) Seite 18 Method of Taping / Polarity and Orientation8) page 18
Markierung mark 200 mg Verpackungseinheit 800/Rolle, ø180 mm Packing unit 800/reel, ø180 mm
Cathode/Collector Side
11.5 (0.453)
4 (0.157) 1.55 (0.061) 2 (0.079)
1.75 (0.069)
0.3 (0.012)
12.4 (0.488)
6.35 (0.250) 8 (0.315)
24 (0.945)
1.9 (0.075)
OHAY0508
2007-08-16
11
7.35 (0.289)
0.3 (0.012)
6.8 (0.268)
(R0.85 (0.033))
11.2 (0.441) 10.8 (0.425) 1.2 (0.047)
LW W5SN
Empfohlenes Lötpaddesign8) Seite 18 Recommended Solder Pad8) page 18 IR Reflow Löten IR Reflow Soldering
Achtung: Anode und Heatsink sind elektrisch verbunden Attention: Anode and Heatsink are electrically connected Footprint
3 Lötstellen 3 solder points
Thermisch optimiertes PCB Thermal enhanced PCB
11.6 (0.457) 1.6 (0.063)
ø4.0 (0.157) Heatsink attach
12.0 (0.472) 11.6 (0.457)
Empfohlene Padgeometrie
0.3 (0.012)
ø4.0 (0.157) ø2.5 (0.098) 1.6 (0.063)
Lötstopplack Solder resist Lötpasten Schablone Solder paste stencil Bare Copper Freies Kupfer
2007-08-16
Kupfer Copper
OHPY2844
12
10 (0.394)
Recommended Solder Pad Design
2.3 (0.091)
2.3 (0.091)
LW W5SN
Lötbedingungen Soldering Conditions IR-Reflow Lötprofil für bleifreies Löten IR Reflow Soldering Profile for lead free soldering Vorbehandlung nach JEDEC Level 2 Preconditioning acc. to JEDEC Level 2 (nach J-STD-020B) (acc. to J-STD-020B)
300 ˚C 255 ˚C 240 ˚C 217 ˚C 200
OHLA0687
T
250
Maximum Solder Profile Recommended Solder Profile Minimum Solder Profile
˚C 260 ˚C +0˚C -5 245 ˚C ±5 ˚C ˚C 235 ˚C +5˚C -0
10 s min 30 s max
150 120 s max 100 Ramp Up 3 K/s (max) 25 ˚C 0 0 50 100 150 200 100 s max
Ramp Down 6 K/s (max)
50
250
s
300
t
Anm.: Das Gehäuse ist für Ultraschallreinigung nicht geeignet Note: Package not suitalbe for ultra sonic cleaning
2007-08-16
13
LW W5SN
Barcode-Produkt-Etikett (BPL) Barcode-Product-Label (BPL)
OSRAM Opto
Semiconductors
(6P) BATCH NO: Batch Number
Bar Code
(1T) LOT NO: Lot Number
m
W1
(9D) D/C: Date Code
pl e
13.0 ±0.25
Lx xxxx Bin1: Bin Information Color 1 Bin2: Product Name Bin3:
RoHS Compliant ML Temp ST 2 260 C RT
Additional TEXT R077 DEMY PACKVAR: Packing Type
Bar Code
(X) PROD NO: Product Code
Sa
F W E A N
W2
(Q)QTY: Product Quantity per Reel
(G) GROUP: X - X - X Forward Voltage Group Wavelength Group Brightness Group
OHA12043
Bar Code
Gurtverpackung Tape and Reel
D0 P2
P0
P1 Direction of unreeling
Label
Direction of unreeling
Gurtvorlauf: 400 mm 400 mm Leader: Gurtende: Trailer: 160 mm 160 mm
OHAY0324
Tape dimensions in mm (inch) W P0 P1 P2 D0 E F
24 + 0.3 – 0.1
4 ± 0.1 8 ± 0.1 2 ± 0.1 1.5 + 0.1 1.75 ± 0.1 11.5 ± 0.1 (0.157 ± 0.004) (0.315 ± 0.004) (0.079 ± 0.004) (0.059 + 0.004) (0.069 ± 0.004) (0.453 ± 0.004)
Reel dimensions in mm (inch) A 180 (7) W 24 (0.945) Nmin 60 (2.362) W1 24.4 + 2 (0.961 + 0.079) W2 max 30.4 (1.197)
2007-08-16
14
LW W5SN
Trockenverpackung und Materialien Dry Packing Process and Materials
Moisture-sensitive label or print
L VE LE see . lab e H) nk, bla cod (R If y bar . dit RH mi % hu e /60 ve ed ag ˚C ati rar ck rel 30 RS _ < inf pa % ins VE of to ak ITI TO 90 urs nta d ). < ns (pe or urs d co NSUC Ho de , cte itio urs g SEND Ho an bje ing co ˚C 72 nd Ho urs 5 ba E CO te 48 ˚C su ss e Ho co ± is UR ce 24 6 da e y MI 40 be tim h ˚C e ThIST l pro < tor tim SE or ). 23 tim e at t wilnt˚C or l wit fac MO Flo tim TO s at or ca at re. Flo d tha ale el or nth OP nti Flo uiv du if: rea es l45 Flo lab mo ide ce eq low g, l ve vic is be or de 24 tin en l 5a pro ve 6 Le de , e te co e , g: ve l un wh Le r se da ak ure ba ed low ba Le ve mo % b e al d ure Le ist en ref e e 10 tim ure se for ist ale op se for > Mo , se 3 ist ure is or . , is ha se Mo nk be ist nk rd g -03 Mo in Flo RH g, r-p bla Mo ba TD po If bla hin % kin Ca life s (if ar t. s wit 10 ba tor J-S thi va p. elf Ye ar ek , _ < e ica me , C 1 urs Ye er tem ted t t Sh a ed low uir > 1 WeHo un Aft Indno uir DE 1. e 48 ref dy red reqy is 2. bo e Mo /JE tim dit 16 req : e 2b a) Sto es tim or mi ed or g is IPC tim e vic b) or e Hu Flo en tim or De 2a kin nc te Flo a) op or 3. b) baere Flo da e l12 Flo If al ref tim ve l 2a 4. se d ve el Le g l3 an Le ev Ba ve te ure L ure Le ist Da ure ist Mo ist ure Mo ist Mo Mo
el
Barcode label
N TIO U A C
O
S
R
A
M
Humidity indicator Barcode label Desiccant
Please check the HIC immidiately after bag opening. Discard if circles overrun. Avoid metal contact. Do not eat.
Anm.: Feuchteempfindliche Produkte sind verpackt in einem Trockenbeutel zusammen mit einem Trockenmittel und einer Feuchteindikatorkarte Bezüglich Trockenverpackung finden Sie weitere Hinweise im Internet und in unserem Short Form Catalog im Kapitel “Gurtung und Verpackung” unter dem Punkt “Trockenverpackung”. Hier sind Normenbezüge, unter anderem ein Auszug der JEDEC-Norm, enthalten. Note: Moisture-senisitve product is packed in a dry bag containing desiccant and a humidity card. Regarding dry pack you will find further information in the internet and in the Short Form Catalog in chapter “Tape and Reel” under the topic “Dry Pack”. Here you will also find the normative references like JEDEC.
Kartonverpackung und Materialien Transportation Packing and Materials
L VE LE see . lab e H) nk, bla cod (R If y bar . dit RH mi % hu e /60 ve ed ag ˚C ati rar ck rel 30 _ < inf pa % of to ak 90 urs d ). < ns (pe or d Ho urs de , cte itio Ho urs an bje ing co ˚C 72 nd Ho urs 5 te 48 ˚C su ss e Ho co ± ce 24 6 da y 40 be tim e e ˚C h l pro < tor tim or e ). wit 23 tim at t wilnt or l fac ˚C Flo tim s at or ca ale at re. Flo d or el nth tha nti Flo uiv du 4 if: rea es l Flo lab mo ide 5 ce eq low g, ve l vic 5a is be or de 24 tin en pro 6 Le ve l de , e te co , g: un wh Le ve l ke r se da ure ba ed low Le ve mo % ba e ba al d Le ist ure en ref e e 10 tim se for ist ure ale op se for > Mo , se 3 ist ure is or . , se is ha Mo nk be ist nk g rd -03 Mo in Flo r-p RH g, bla Mo ba Ca TD po If bla hin % kin life s (if ar s p. wit 10 ba tor t. J-S thi va elf Ye ar ek , _ < e ica me , C 1 urs Ye er tem ted t Sh at ed low uir > 1 WeHo un Aft Indno uir DE dy 1. e 48 ref red reqy is 2. bo Mo /JE tim e e dit 16 req : 2b a) Sto es tim or mi is e ed or g e IPC tim vic b) or Hu Flo en tim or De 2a kin nc te Flo a) op or 3. b) baere Flo da e 1 l Flo If al ref tim ve l 2 2a 4. se d 3 Le ve l g an Le ve l Ba te ure Le ve Le ist ure Da ist ure Mo ist ure Mo ist Mo Mo
el
N VE RS ins IONSITI TO T nta UC SE U g co ND A ba ECO is UR CThISTSEMI
MO TO OP
Muster
ED Bin Bin 1: Bin 2: P3: Q- 1-2 ML 1-2 0 2 0 Te 2a 22 mp 3 24 0 ST Ad 26 0 C R 0C R0 dit ion C R RT PA 77 al CK TE VA XT R:
M ul LS ti Y TO T6 PL 76
R1 8
DE
MY
Se S m RA ic M on du O ct pto or H NO s
3G H1 23 4
O
TC
BA
Barcode label
Muster
ED Bin Bin 1: Bin 2: P-1 3: Q- -20 ML 1-2 2 0 Te 2a 22 mp 3 24 0 ST Ad 26 0 C R 0C R0 dit ion C R RT PA 77 al CK TE VA XT R:
(X
)
PR
OD
NO
25 014 110
(6P
(1T
)
LO
T
NO
: 12
)
ul LS ti Y TO T6 PL 76
R1
8
DE MY
:
M
on M du O ct pto or s
BA TC H
3G
(X)
PR OD
NO :
25 014 110
(1T )
LO T
NO : 12
(6P )
(Q )Q TY : 20
NO :
S
ic
O
m
Se
H1
23
210
A
R
4
00
021
(9D )
D/C : 01
998
44
(G )
GR OU P:
P-
1+
Q
-1
(Q
)Q
TY
: 20
8 2199 2100
(9D
)
D/
C:
01 44
:
00
(G
)
GR
OU
P:
P1+ Q -1
Packing Sealing label
OHA02044
2007-08-16
15
O
SR
AM
WET 15% 10% 5%
Humidity Indicator MIL-I-8835
Comparator check dot If wet, examine units, if necessary bake units If wet, examine units, if necessary bake units If wet, parts still adequately dry. change desiccant
OSR
AM
OHA00539
Barcode label
LW W5SN
Revision History: 2007-08-16 Previous Version: 2007-08-10 Page 1, 13 Subjects (major changes since last revision) OS-IN-2007-018 (Introduction of Jedec Level 2) Date of change 2007-08-16
Anm.: Gemäß IEC 60825-1 (EN 60825-1) gilt für weiß: Anm.: According IEC 60825-1 (EN 60825-1) for white:
LED RADIATION DO NOT STARE INTO BEAM CLASS 2 LED PRODUCT
OHW02885
LED STRAHLUNG NICHT DIREKT IN DEN STRAHL BLICKEN LED KLASSE 2
OHW12885
2007-08-16
16
LW W5SN
Patent List Patent No. US 6 066 861 US 6 277 301 US 6 245 259
Attention please! The information describes the type of component and shall not be considered as assured characteristics. Terms of delivery and rights to change design reserved. Due to technical requirements components may contain dangerous substances. For information on the types in question please contact our Sales Organization. If printed or downloaded, please find the latest version in the Internet. Packing Please use the recycling operators known to you. We can also help you – get in touch with your nearest sales office. By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs incurred. Components used in life-support devices or systems must be expressly authorized for such purpose! Critical components9) page 18 may only be used in life-support devices or systems10 ) page 18 with the express written approval of OSRAM OS. 2007-08-16 17
LW W5SN
Fußnoten: 1) Helligkeitswerte werden mit einer Stromeinprägedauer von 25 ms und einer Genauigkeit von ± 11% ermittelt. 2) Wegen der besonderen Prozessbedingungen bei der Herstellung von LED können typische oder abgeleitete technische Parameter nur aufgrund statistischer Werte wiedergegeben werden. Diese stimmen nicht notwendigerweise mit den Werten jedes einzelnen Produktes überein, dessen Werte sich von typischen und abgeleiteten Werten oder typischen Kennlinien unterscheiden können. Falls erforderlich, z.B. aufgrund technischer Verbesserungen, werden diese typischen Werte ohne weitere Ankündigung geändert. 3) 4) Montage auf PC-Board - Metallkernplatine, Fläche 950 mm², λ = 1,3 W/(m*K). Für weitere Informationen siehe Applikationsschrift im Internet (www.osram-os.com) 5) Farbortgruppen werden mit einer Stromeinprägedauer von 25 ms und einer Genauigkeit von ±0.01 ermittelt. 6) Spannungswerte werden mit einer Stromeinprägedauer von 1 ms und einer Genauigkeit von ±0,1 V ermittelt. 7) Im gestrichelten Bereich der Kennlinien muss mit erhöhten Helligkeitsunterschieden zwischen Leuchtdioden innerhalb einer Verpackungseinheit gerechnet werden 8) Maße werden wie folgt angegeben: mm (inch) 9) Ein kritisches Bauteil ist ein Bauteil, das in lebenserhaltenden Apparaten oder Systemen eingesetzt wird und dessen Defekt voraussichtlich zu einer Fehlfunktion dieses lebenserhaltenden Apparates oder Systems führen wird oder die Sicherheit oder Effektivität dieses Apparates oder Systems beeinträchtigt. 10) Lebenserhaltende Apparate oder Systeme sind für (a) die Implantierung in den menschlichen Körper oder (b) für die Lebenserhaltung bestimmt. Falls sie versagen, kann davon ausgegangen werden, dass die Gesundheit und das Leben des Patienten in Gefahr ist. Remarks: 1) Brightness groups are tested at a current pulse duration of 25 ms and a tolerance of ± 11%.
2)
3) 4)
5) 6)
Due to the special conditions of the manufacturing processes of LED, the typical data or calculated correlations of technical parameters can only reflect statistical figures. These do not necessarily correspond to the actual parameters of each single product, which could differ from the typical data and calculated correlations or the typical characteristic line. If requested, e.g. because of technical improvements, these typ. data will be changed without any further notice. Mounted on PC board - metall core PCB, area of 950 mm², λ = 1.3 W/(m*K). For further Information please find the application note on our web site (www.osram-os.com) Chromaticity coordinate groups are tested at a current pulse duration of 25 ms and a tolerance of ±0.01. Forward voltages are tested at a current pulse duration of 1 ms and a tolerance of ±0.1 V. In the range where the line of the graph is broken, you must expect higher brightness differences between single LEDs within one packing unit. Dimensions are specified as follows: mm (inch). A critical component is a component used in a life-support device or system whose failure can reasonably be expected to cause the failure of that life-support device or system, or to affect its safety or the effectiveness of that device or system.
7)
8) 9)
10)
Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintain and sustain human life. If they fail, it is reasonable to assume that the health and the life of the user may be endangered.
Published by OSRAM Opto Semiconductors GmbH Wernerwerkstrasse 2, D-93049 Regensburg www.osram-os.com © All Rights Reserved.
2007-08-16
18