SFH3710-2

NPN-Si-Fototransistor mit Vλ Charakteristik Silicon NPN Phototransistor with Vλ Characteristics Lead (Pb) Free Product - RoHS Compliant SFH 3710 Wesentliche Merkmale • Sehr kleines SMT Gehäuse • Angepaßt an die Augenempfindlichkeit (Vλ) Anwendungen • • • • Umgebungslicht-Detektor Beleuchtungsmesser Dimmungssensor für Hintergrundbeleuchtung „Messen/Steuern/Regeln“ Bestellnummer Ordering Code Q65110A3107 Q65110A3512 Q65110A3511 Features • Very small SMT package • Adapted to human eye sensitivity (Vλ) Applications • • • • t Ambient light detector Exposure meter for daylight and artificial light Sensor for Backlight-Dimming For control and drive circuits Typ Type SFH 3710 SFH 3710-2/3 SFH 3710-3/4 Fotostrom , Ee = 10 µW/cm², λ = 560 nm, VCE = 5 V Photocurrent Ipce (µA) 2.5…12.5 2.5…8.0 4.0…12.5 Einzelgruppen auf Anfrage / single bins on request 2007-11-14 1 SFH 3710 Grenzwerte (TA = 25 ° C) Maximum Ratings Bezeichnung Parameter Betriebs- und Lagertemperatur Operating and storage temperature range Kollektor-Emitterspannung Collector-emitter voltage Kollektorstrom Collector current Emitter-Kollektorspannung Emitter-collector voltage Symbol Symbol Wert Value – 40 …+ 85 5.5 20 0.5 Einheit Unit °C V mA V Top; Tstg VCE IC VEC Kennwerte (TA = 25 ° C) Characteristics Bezeichnung Parameter Wellenlänge der max. Fotoempfindlichkeit Wavelength of max. sensitivity Spektraler Bereich der Fotoempfindlichkeit S = 10% von Smax Spectral range of sensitivity S = 10% of Smax Bestrahlungsempfindliche Fläche Radiant sensitive area Abmessung der Chipfläche Dimensions of chip area Halbwinkel Half angle Kapazität, VCE = 0 V, f = 1 MHz, E = 0 Capacitance Dunkelstrom Dark current VR = 5 V Temperturkoeffizient Temperature Coefficient Normlicht A / Standard Light A λ = 550 nm Symbol Symbol Wert Value 570 350 … 950 Einheit Unit nm nm λ Smax λ A L× B L× W ϕ 0.29 0.75 × 0.75 ± 60 4 3 (< 50) mm2 mm × mm Grad. deg. pF nA CCE ICEO TK TK550 nm 0.9 0.78 %/K %/K 2007-11-14 2 SFH 3710 Kennwerte (TA = 25 ° C) Characteristics Bezeichnung Parameter Fotostrom Photocurrent Ee = 10 µW/cm², λ = 560 nm, VCE = 5 V Ev = 1000 lx, Normlicht/Standard light A Kollektor-Emitter-Sättigungsspannung Collector-emitter saturation voltage IC = IPCEmin1) × 0.3, Ee = 10 µW/cm², λ = 560 nm 1) 1) Symbol Symbol -2 Wert Value -3 -4 Einheit Unit IPCE VCEsat 2.5…5 220 100 4…8 350 100 6.3…12.5 µA 570 µA 100 mV IPCEmin ist der minimale Fotostrom der jeweiligen Gruppe IPCEmin is the min. photocurrent of the specified group 2007-11-14 3 SFH 3710 Relative Spectral Sensitivity Srel = f (λ) 100 90 80 70 1E+00 1E+01 Photocurrent IPCE = f (EV), VCE = 5 V 1E+02 Photocurrent IPCE = f (EV), VCE = 5 V normalized to 1000lx 100 90 80 Srel / % Ipce (mA) 60 50 40 30 20 Ipce rel (%) 70 60 50 40 1E-01 1E-02 30 20 10 1E-03 10 0 400 500 600 700 800 900 1000 1100 1E-04 1.E+00 1.E+01 1.E+02 1.E+03 1.E+04 1.E+05 lambda / nm Ev (lx) 0 1.E+00 1.E+01 1.E+02 1.E+03 1.E+04 1.E+05 Ev (lx) Collector-Emitter Capacitance CCE = f (VCE) 4.0 pF 3.5 CCE 3.0 2.5 2.0 1.5 1.0 0.5 0.0 1E-03 1E-02 1E-01 1E+00 1E+01 VCE V 1E+02 Directional Characteristics Srel = f (ϕ) 40 30 20 10 ϕ 0 1.0 OHF01402 50 0.8 60 0.6 70 0.4 80 0.2 0 90 100 1.0 0.8 0.6 0.4 0 20 40 60 80 100 120 2007-11-14 4 SFH 3710 Maßzeichnung Package Outlines Maße in mm (inch) / Dimensions in mm (inch) Empfohlenes Lötpaddesign Recommended Solderpad Design 3.2 1.25 1 Bauteil positioniert Component location on pad OHFP2578 Maße in mm / Dimensions in mm 2007-11-14 5 SFH 3710 Lötbedingungen Soldering Conditions Reflow Lötprofil für bleifreies Löten Reflow Soldering Profile for lead free soldering 300 ˚C 255 ˚C 240 ˚C 217 ˚C 200 30 s max 150 120 s max 100 Ramp Up 3 K/s (max) 25 ˚C 0 0 50 100 150 200 250 s 300 100 s max Ramp Down 6 K/s (max) 10 s min Vorbehandlung nach JEDEC Level 2 Preconditioning acc. to JEDEC Level 2 (nach J-STD-020C) (acc. to J-STD-020C) OHLA0687 T 250 Maximum Solder Profile Recommended Solder Profile Minimum Solder Profile ˚C 260 ˚C +0˚C -5 245 ˚C ±5 ˚C ˚C 235 ˚C +5˚C -0 50 t Published by OSRAM Opto Semiconductors GmbH Wernerwerkstrasse 2, D-93049 Regensburg www.osram-os.com © All Rights Reserved. The information describes the type of component and shall not be considered as assured characteristics. Terms of delivery and rights to change design reserved. Due to technical requirements components may contain dangerous substances. For information on the types in question please contact our Sales Organization. Packing Please use the recycling operators known to you. We can also help you – get in touch with your nearest sales office. By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs incurred. Components used in life-support devices or systems must be expressly authorized for such purpose! Critical components 1 , may only be used in life-support devices or systems 2 with the express written approval of OSRAM OS. 1 A critical component is a component usedin a life-support device or system whose failure can reasonably be expected to cause the failure of that life-support device or system, or to affect its safety or effectiveness of that device or system. 2 Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintain and sustain human life. If they fail, it is reasonable to assume that the health of the user may be endangered. 2007-11-14 6