FDC15-24D15

FEATURES • 15 WATTS OUTPUT POWER • OUTPUT CURRENT UP TO 3A • STANDARD 2.0 X 1.6 X 0.4 INCH PACKAGE • HIGH EFFICIENCY UP TO 82% • 4:1 WIDE INPUT VOLTAGE RANGE • SIX-SIDED CONTINUOUS SHIELD • FIXED SWITCHING FREQUENCY • CE MARK MEETS 2006/95/EC,93/68/EEC AND 2004/108/EC • UL60950-1, EN60950-1 AND IEC60950-1 LICENSED • ISO9001 CERTIFIED MANUFACTURING FACILITIES • COMPLIANT TO RoHS EU DIRECTIVE 2002/95/EC APPLICATIONS Wireless Network Telecom/Datacom Industry Control System Measurement Equipment Semiconductor Equipment DESCRIPTION The FDC15 series offer 15 watts of output power from a 2 x 1.6 x 0.4 inch package. The FDC15 series have 4:1 wide input voltage of 9-36 and 18-75VDC. The FDC15 features 1600VDC of isolation, short-circuit and over-voltage protection. T E C H N I C A L S P E C I F I C AT I O N OUTPUT SPECIFICATIONS Output power Voltage accuracy Minimum load (Note 6) Voltage adjustability Line regulation LL to HL at Full Load Single Load regulation Min. load to Full load Dual Cross regulation (Dual) Asymmetrical load 25% / 100% FL Ripple and noise Temperature coefficient 20MHz bandwidth Full load and nominal Vin All specifications are typical at nominal input, full load and 25ºC otherwise noted INPUT SPECIFICATIONS 15 Watts, max. ± 1% See Table ± 10% ± 0.2% ± 0.5% ± 1% ± 5% See table ±0.02% / ºC, max. 250μS 6.2VDC 15VDC 18VDC 150%, max. Input voltage range Input filter Input surge voltage 100mS max 24V input 48V input Nominal Vin and full load 24V nominal input 48V nominal input 9 – 36VDC 18 – 75VDC Pi type 50VDC 100VDC 20mAp-p Input reflected ripple current Transient response recovery time 25% load step change 5V output Over voltage protection 12V output Zener diode clamp 15V output Over load protection % of FL at nominal input Short circuit protection Nominal Vin and Power up Start up time 20mS, typ. constant resistive load Remote ON/OFF (Note 7) (Positive logic) DC-DC ON Open or 3.5V < Vr < 12V DC-DC OFF Short or 0V < Vr < 1.2V Input current of remote control pin Nominal Vin -0.5mA~+0.5mA Remote off state input current Nominal Vin 20mA ENVIRONMENTAL SPECIFICATIONS Operating ambient temperature Maximum case temperature Storage temperature range -40ºC ~ +85ºC (with derating) 100ºC -55ºC ~ +105ºC Hiccup, automatics recovery GENERAL SPECIFICATIONS Efficiency Isolation voltage Isolation resistance Isolation capacitance Switching frequency Approvals and standard Case material Base material Potting material Dimensions Weight MTBF (Note 1) BELLCORE TR-NWT-000332 MIL-HDBK-217F 9 See table 1600VDC, min. 10 ohms, min. 300pF, max. 270KHz, typ. IEC60950-1, UL60950-1, EN60950-1 Nickel-coated copper Non-conductive black plastic Epoxy (UL94-V0) 2.00 X 1.60 X 0.40 Inch (50.8 X 40.6 X 10.2 mm) 48g (1.69oz) 2.041 x 10 hrs 5 9.140 x 10 hrs 6 Nature convection 10ºC/Watt Thermal impedance (Note 8) Nature convection with heat-sink 8.24ºC/Watt Thermal shock Vibration Relative humidity MIL-STD-810F MIL-STD-810F 5% to 95% RH EMC CHARACTERISTICS EMI ESD Radiated immunity EN55022 EN61000-4-2 EN61000-4-3 Class A Air ± 8KV Perf. Criteria B Contact ± 6KV 10 V/m Perf. Criteria A Fast transient (Note 9) EN61000-4-4 Surge (Note 9) Conducted immunity EN61000-4-5 EN61000-4-6 ± 2KV Perf. Criteria B ± 1KV Perf. Criteria B 10 Vr.m.s Perf. Criteria A Page 1 of 3 Issued Date：2008/05/21 Model Number FDC15-24S05 FDC15-24S12 FDC15-24S15 FDC15-24D05 FDC15-24D12 FDC15-24D15 FDC15-48S05 FDC15-48S12 FDC15-48S15 FDC15-48D05 FDC15-48D12 FDC15-48D15 Input Range 9 – 36 VDC 9 – 36 VDC 9 – 36 VDC 9 – 36 VDC 9 – 36 VDC 9 – 36 VDC 18 – 75 VDC 18 – 75 VDC 18 – 75 VDC 18 – 75 VDC 18 – 75 VDC 18 – 75 VDC Output Current Input Current (4) (4) Output Output Capacitor Eff No load Full load Voltage Min. load Full load Ripple & Noise (%) Load max(5) (3) (2) 5 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC 210mA 100mA 80mA ± 105mA ± 50mA ± 40mA 210mA 100mA 80mA ± 105mA ±50mA ± 40mA 3000mA 1250mA 1000mA ± 1500mA ± 625mA ± 500mA 3000mA 1250mA 1000mA ± 1500mA ± 625mA ± 500mA 75mVp-p 75mVp-p 75mVp-p 75mVp-p 75mVp-p 75mVp-p 75mVp-p 75mVp-p 75mVp-p 75mVp-p 75mVp-p 75mVp-p 20mA 10mA 20mA 20mA 20mA 20mA 15mA 15mA 10mA 10mA 20mA 15mA 822mA 801mA 801mA 822mA 801mA 801mA 411mA 401mA 401mA 411mA 401mA 401mA 80 82 82 80 82 82 80 82 82 80 82 82 6800μF 890μF 570μF ± 1700μF ± 300μF ± 200μF 6800μF 890μF 570μF ± 1700μF ± 300μF ± 200μF Note 1. 2. 3. 4. 5. 6. 7. 8. 9. BELLCORE TR-NWT-000332. Case 1: 50% Stress, Temperature at 40ºC. MIL-HDBK-217F Notice2 @Ta=25 ºC, Full load(Ground, Benign, controlled environment). Maximum value at nominal input voltage and full load. Typical value at nominal input voltage and no load. Typical value at nominal input voltage and full load. Test by minimum Vin and constant resistive load. The output requires a minimum loading on the output to maintain specified regulation. Operation under no-load condition will not damage these devices, however they may not meet all listed specification. The ON/OFF control pin voltage is reference to -Vin. Heat-sink is optional and P/N: 7G-0011C-F. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The filter capacitor Power Mate suggest: Nippon chemi-con KY series, 220μF /100V, ESR 48mΩ. OUTPUT POWER (%) FDC15-48S05 Derating Curve 100 80 60 40 20 0 -40 -20 0 20 40 60 62.5 80 100 120 OUTPUT POWER(%) 120 120 100 80 60 40 20 0 FDC15-48S05 Derating Curve With Heatsink ((Note 6 ) Note 8 ) -40 -20 0 20 40 60 69.1 80 100 120 AMBIENT TEMPERATURE(℃) AMBIENT TEMPERATURE(℃ ) FDC15-48S05 Efficiency VS Input Voltage EFFICIENCY(%) 82% 80% 78% 76% 74% 72% 70% 36 40 44 48 52 56 60 64 68 72 95 90 85 80 75 70 65 60 55 50 45 FDC15-48S05 Efficiency VS Output Load INPUT VOLTAGE (V) EFFICIENCY(%) 10 20 30 40 50 60 70 80 90 100 OUTPUT LOAD (% of Full Load) Page 2 of 3 Issued Date：2008/05/21 Recommended Filter for EN55022 Class B Compliance The components used in the above figure, together with the manufacturers’ part numbers for these components, are as follows: 1. All dimensions in Inches (mm) Tolerance: X.XX±0.02 (X.X±0.5) X.XXX±0.01 (X.XX±0.25) 2. Pin pitch tolerance ±0.01(0.25) 3. Pin dimension tolerance ±0.004 (0.1) C1 FDC15-24xxx 6.8μF/50V 1812 MLCC 2.2μF/100V 1812 MLCC PIN CONNECTION PIN 1 2 4 5 6 7 8 SINGLE + INPUT - INPUT CTRL NO PIN + OUTPUT - OUTPUT TRIM DUAL + INPUT - INPUT CTRL + OUTPUT COMMON - OUTPUT TRIM FDC15-48xxx L1 450μH 1000pF/2KV 1000pF/2KV Common N/A MLCC MLCC Choke PMT-048 450μH 2.2μF/100V 1000pF/2KV 1000pF/2KV Common 1812 MLCC MLCC MLCC Choke PMT-048 C2 C3 C4 EXTERNAL OUTPUT TRIMMING Output can be externally trimmed by using the method shown below. ( ) for dual output trim TRIM UP TRIM DOWN 7(7) 8(8) RU 8(8) 6(5) RD Recommended EN55022 Class B Filter Circuit Layout Page 3 of 3 Issued Date：2008/05/21