HGL34J

HGL34A thru HGL34M SURFACE MOUNT GLASS PASSIVATED HIGH EFFICIENCY RECTIFIER DO-213AA / MINI MELF SOLDERABLE ENDS D1= 0.066(1.676) 0.060(1.524) CATHODE BAND D2 0.022(0.559) 0.016(0.406) 0.145(3.683) 0.131(3.327) D2=D1 +0 -0.008(0.20) Dimension in inches (millimeters ) FEATURES Ldeal for surface mounted applications Easy pick and place Low leakage current Glass passivated chips Fast switching Metallurgically bonded construction High temperature soldering guaranteed 250oC/10 seconds/.375 , (9.5mm) lead lengths MECHANICAL DATA Molded plastic use UL94V-0 recoqnized flame retardant epoxy Terminals Plated terminals, solderable per MIL-STD-202, Method208 Polarity Red Color band on body denotes cathode Mounting position Any Weight 0.036gram Case MAXIMUM RATIXGS AND ELECTRICAL CHARACTERISTICS Ratings at 25oC ambient temp. unless otherwise specified Single phase, half sine wave, 60Hz, resistive or inductive load For capacitive load, derate current by 20% SYMBOL Maximum Current Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current TT=600C Peak Forward Surge Current Single Sine-Wave on Rated Load(JEDEC Method) Maximum Instantaneous Forward Voltage Drop at 0.5A DC Maximum DC Reverse Current TA=250C at Rated DC Blocking Voltage TA=1250C Maximum Reverse Recovery Time Typical Junction Capacitance Operating Junction Temperature Range Storage Temperature Range VRRM VRMS VDC I(AV) IFSM VF IR TRR CJ TJ TSTG 50 15 1.25 5.0 100 75 12 HGL 34A HGL 34B HGL 34D HGL 34G HGL 34J HGL 34K HGL 34M UNITS Volts Volts Volts Amps Amps 50 35 50 100 70 100 200 140 200 400 280 400 0.5 10 600 420 600 800 560 800 1000 700 1000 1.35 1.5 Volts A nS pF 0 -65 to +150 -65 to +150 C C 0 NOTES 1. Reverse Recovery Test Conditions IF=0.5A, I R=1.0A, I RR=0.25A 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 Volts D.C www.paceleader.tw 1 HGL34A thru HGL34M SURFACE MOUNT GLASS PASSIVATED HIGH EFFICIENCY RECTIFIER RATING AND CHARACTERISTICS CURVES HGL34A THRU HGL34M FIG. 1 - MAXIMUM FORWARD CURRENT DERATING CURVE 1.50 1.26 Single Phase Half Wave 60Hz Resistive or Inouctive Load 0.375"(9.5mm) Lead Length FIG. 2 - MAXIMUM NON - REPETITIVE PEAK FORWARD SURGE CURRENT 16 PEAK FORWARD SURGE CURENT. (A) AVERAGE FORWARD CURRENT (A) 13 10 7 4 8.3ms Single Half Sine Wave JEDEC Method 1.00 TJ=25 C o 0.75 0.50 0.25 0 0 1 2 4 6 8 10 20 40 60 80 100 0 25 50 75 100 125 150 175 AMBIENT TEMPERATURE (oC) NUMBER OF CYCLES AT 60Hz FIG. 4 - TYPICAL FORWARD CHARACTERISTICS FIG. 3 - TYPICAL JUNCTION CAPACITANCE 100 10 INSTANTANEOUS FORWARD CURRENT.(A) JUNCTION CAPACITANCE.(pF) 1.0 TJ=25oC 10 0.1 TJ=25oC Pulse Width=300 s 1% Duty Cycle .01 .4 1 1 10 100 .6 .8 1.0 1.2 1.4 1.6 FORWARD VOLT AGE.(V) REVERSE VOLTAGE. (V) FIG. 5 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 NONINDUCTIVE 10 NONINDUCTIVE +0.5A trr () PULSE GENERATOR (NOTE 2) 0 -0.25A DUT (+) 50Vdc (approx) () 1 NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (+) NOTES : 1. Rise Time=7ns max. Input Impedance= 1 megohm. 22pF 2. Rise Time=10ns max. Source Impedance= 50 Ohms. -1.0A 1cm SET TIME BASE FOR 5/ 10ns/cm www.paceleader.tw 2