AN6561

AN6561, AN6561L Dual Operational Amplifiers s Overview The AN6561 and AN6561L are dual operational amplifiers with two phase compensation circuits built in, have a wide range of operating supply voltage, and can operate on a single power supply. They have electrical characteristics equivalent to those of conventional operational amplifiers, and are lowpowered and suitable for application to various circuits. AN6561 2.4±0.25 3.3±0.25 6.0±0.3 Unit:mm 8 0.5±0.1 7 23.3±0.3 6 5 4 1.5±0.25 2 1 s Features • Built-in phase compensation circuits • Wide range of input voltage:0V to VCC –1.5V • Wide range of operating power supply • Single power supply:3 to 30V • Dual power supply:±1.5 to 15V 0.3 – 0.05 3.0±0.3 + 0.1 9-pin SIL Plastic Package (SIP009-P-0000C) AN6561L 9 8 6 21.7±0.3 5 4 3 2 1 1.0±0.25 4.3±0.3 2.54 0.5±0.1 7 0.4±0.25 1.4±0.3 30˚ 3 1.5±0.25 2.54 9 Unit:mm 2.7±0.25 +0.1 0.3 – 0.05 9-pin SIL Plastic Package (SIP009-P-0000A) s Block Diagram 1 – 1 VCC 2 VO1 3 Vin1– + 4 Vin1+ 5 VEE (GND) + 6 Vin2+ 2 – 7 Vin2– 8 VO2 9 VCC 1.2±0.25 1.4±0.25 1.35±0.25 s Absolute Maximum Rating (Ta=25˚C) Parameter Supply voltage Differential input voltage Common-mode input voltage Output voltage Power dissipation Operating ambient temperature Storage temperature Symbol VCC VID VICM VO PD Topr Tstg Rating 32 32 – 0.3 to +32 24 350 –20 to +75 –55 to +150 Unit V V V V mW ˚C ˚C s Recommended Operating Range (Ta=25˚C) Parameter Operating supply voltage range Symbol VCC Range Single power supply 3V to 30V Dual power supply ±1.5V to ±15V s Electrical Characteristics (VCC=5V, Ta=25˚C) Parameter Input offset voltage Input bias current Input offset current Common-mode input voltage width Supply current Voltage gain Maximum output voltage Common-mode rejection ratio Supply voltage rejection ratio Channel separation Output source current Output sink current Symbol VI (offset) IBias IIO VCM ICC GV VO (max.) CMR SVR CS IO (source) ISINK f=1kHz to 20kHz Vin+=1V, Vin–= 0V Vin+= 0V, Vin–=1V 20 10 RL=∞ RL > 2kΩ = RL > 2kΩ = VCC–1.5 65 65 85 100 120 40 20 0 0.6 100 RS=50Ω Condition min typ 2 max 7 250 50 VCC–1.5 1.2 Unit mV nA nA V mA dB V dB dB dB mA mA s Application Circuit Non-inverting amplifier R2 VCC s Pins Descriptions Pin No. 1 2 VO = 1+ R2 Vin R1 VO Pin name Positive supply voltage Ch.1 output pin Ch.1 inverting input pin Ch.1 non-inverting input pin Negative supply voltage (GND) Ch.2 non-inverting input pin Ch.2 inverting input pin Ch.2 output pin Positive supply voltage 3 4 5 6 7 8 9 – OP. Amp. R1 Vin + s Characteristics Curve VI (offset) –VCC Input Offset Voltage VI (offset) (mA) Input Offset Current IIO (mA) 5 4 3 2 1 0 –1 –2 –3 –4 –5 0 4 8 12 16 20 24 28 32 15 10 5 0 –5 –10 –15 IIO –VCC Input Bias Current IBias (mA) 80 70 60 50 40 30 20 10 0 0 4 8 IBias–VCC Ta=25˚C 0 4 8 12 16 20 24 28 32 12 16 20 24 28 32 Supply Voltage VCC (V) Supply Voltage VCC (V) Supply Voltage VCC (V) 120 1.2 Output Current IO (Source), ISINK (mA) GV – f Supply Current ICC (mA) Voltage Gain GV (dB) 100 80 60 40 20 0 VCC=15V Ta=25˚C 1.0 0.8 ICC –VCC (1) Ta= –20˚C (2) Ta=25˚C (3) Ta=75˚C (1) (2) IO (Source), ISINK–Ta 60 50 IO (source) 40 30 20 ISINK 10 0 –20 Vin– Vin+ IO (source) (3) 0.6 0.4 0.2 1 10 100 1k 10k 100k 1M 0 4 8 12 16 20 24 28 32 36 40 44 0 20 40 60 80 100 Frequency f (Hz) Supply Voltage VCC (V) Ambient Temperature Ta (˚C) 16 Input Voltage Vin (V), Output Voltage VO (V) VO – fi 100kΩ VI 1kΩ VCC 2 – + Vin, VO – t VCC= –15V VI GV –VCC 140 VO 2kΩ Output Voltage VO (V) 12 10 8 6 4 2 0 100 300 1k 3k VO 2kΩ VCC=15V 4 3 2 1 0 3 2 1 0 + Voltage Gain GV (dB) 14 – Ta=25˚C 120 100 80 10k 30k 100k 300k 1M 0 20 40 60 80 100 60 0 4 8 12 16 20 24 28 32 Input Frequency fi (Hz) Time t (µs) Supply Voltage VCC (V)