Voltage Regulators
AN80PxxRSP Series
5-pin, low dropout voltage regulator with standby function (1 A type)
I Overview
1.80±0.10
(2.50)
The AN80PxxRSP series is a 1 A, low dropout voltage regulator with standby function, featuring low current consumption and low noise.
6.50±0.10 5.40±0.10 (4.35) (3.00)
Unit: mm
0.50±0.10 1.00±0.10
5.50±0.10
• Standby consumption current: max. 3 µA • Dropout voltage: 0.3 V • Output voltage accuracy: ±3% • 5-pin surface mounting package • Ripple rejection ratio of 30 dB (f = 500 kHz) • Output voltage: 1.8 V, 1.9 V, 2.0 V, 2.1 V, 2.2 V, 2.5 V, 2.7 V, 2.8 V, 2.9 V, 3.0 V, 3.1 V, 3.2 V, 3.3 V, 3.4 V, 3.5 V, 3.6 V, 4.8 V, 4.9 V, 5.0 V, 5.1 V, 5.2 V, 5.3 V
9.80±0.20
I Features
(5.50)
(2.50)
3 1 2 4 5 (0.75) 5.08±0.10
(0.80)
1.27±0.10
0.50±0.10
0.50±0.10 0.10±0.10
SP-5SU
I Applications
• General use power supply
Note) The package of this product will be changed to lead-free type (SP-5SUA). See the new package dimensions section later of this datasheet.
I Block Diagram
Input short-circuit protection
Output stage
Voltage reference
Output driver
Overcurrent limitter Inrush current protection Thermal protection R1
Starter
VREF
Error amplifier
R2
1 VIN CIN
2
3 (Fin)
4 COUT1
2.30±0.10
5 VOUT
Cont. CIN: 100 µF, CNR: 1 µF, COUT1: 33 µF, COUT2: 0.1 µF
Publication date: November 2001 SFF00010CEB
COUT2 CNR
1.00±0.20
1
AN80PxxRSP Series
I Pin Descriptions
Pin No. 1 2 3 4 5 Input voltage pin (VIN) Control pin (Cont.) High: operation, Low: stop Electrically in common with radiation fin Open when the noise reduction function is not used Description
Grounding pin (GND)
Noise reduction pin (N.R.) Output voltage pin (VOUT)
I Absolute Maximum Ratings
Parameter Supply voltage Supply current Power dissipation
*1 *2
Symbol VCC ICC PD Topr Tstg
Rating 14.4 255 −30 to +85 −55 to +150
Unit V mA mW °C °C
Operating ambient temperature Storage temperature
*2
Note) 1. The output voltage may exceed the rated value if Tj > 150°C in no-load condition. Set to IO > 5 mA if Tj is likely to exceed 150°C. 2. This IC is not suitable for automobile equipment use. 3. *1: The above power dissipation shows the value of an independent IC without heat sink at Ta = 85°C. For details, refer to "2. Power dissipation of SP-5SU package" in the Application Notes. *2: Except for the operating ambient temperature and storage temperature, all ratings are for Ta = 25°C.
2
SFF00010CEB
AN80PxxRSP Series
I Recommended Operating Conditions
Part No. AN80P18RSP AN80P19RSP AN80P20RSP AN80P21RSP AN80P22RSP AN80P25RSP AN80P27RSP AN80P28RSP AN80P29RSP AN80P30RSP AN80P31RSP AN80P32RSP AN80P33RSP AN80P34RSP AN80P35RSP AN80P36RSP AN80P48RSP AN80P49RSP AN80P50RSP AN80P51RSP AN80P52RSP AN80P53RSP Output voltage 1.8 1.9 2.0 2.1 2.2 2.5 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 4.8 4.9 5.0 5.1 5.2 5.3 Operating supply voltage range (VCC) 2.3 to 14.0 2.4 to 14.0 2.5 to 14.0 2.6 to 14.0 2.7 to 14.0 3.0 to 14.0 3.2 to 14.0 3.3 to 14.0 3.4 to 14.0 3.5 to 14.0 3.6 to 14.0 3.7 to 14.0 3.8 to 14.0 3.9 to 14.0 4.0 to 14.0 4.1 to 14.0 5.3 to 14.0 5.4 to 14.0 5.5 to 14.0 5.6 to 14.0 5.7 to 14.0 5.8 to 14.0 Unit V V V V V V V V V V V V V V V V V V V V V V
SFF00010CEB
3
AN80PxxRSP Series
I Electrical Characteristics at Ta = 25°C
• AN80P18RSP (1.8 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 100 µF, CNR = Open, COUT = 0.1 µF Parameter Output voltage Line regulation Load regulation Peak output current Symbol VOUT REGIN IPEAK Conditions VIN = 2.8 V, IOUT = 500 mA VIN = 2.8 V → 14.0 V, IOUT = 250 mA Min 1.746 Typ 1.8 Max 1.854 18 36 Unit V mV mV mA
REGLOA VIN = 2.8 V, IOUT = 0 mA → 1 000 mA
VIN = 2.8 V, The output current value 1 200 when VOUT decreases by 5% from its value at IOUT = 500 mA. VIN = 2.8 V, IOUT = 0 mA −5 58.8 0.50
Bias current under no load Bias current fluctuation to input Bias current fluctuation to load Standby consumption current Bias current before starting regulation Control terminal current Ripple rejection ratio 1 Minimum input/ output voltage difference 1 Minimum input/ output voltage difference 2 Control terminal threshold high voltage Control terminal threshold low voltage • Design reference data
IBIAS
1.1 0.30 1.45 0.70
3.0 5 50 3.0 5 30 0.60 1.0 1.80
mA mA mA µA mA µA dB V V V V
∆IBIAS(IN) VIN = 2.8 V → 14.0 V, IOUT = 250 mA ∆IBIAS(LOA) VIN = 2.8 V, IOUT = 0 mA → 1 000 mA ISTB IRUSH ICONT RR1 VIN = 14.0 V, VCONT = 0 V VIN = 1.710 V, IOUT = 0 A VIN = 2.8 V, IOUT = 500 mA VCONT = 1.8 V VIN = 3.8 V ± 1 V[p-p] f = 120 Hz, IOUT = 100 mA
VDIF(min)1 VIN = 1.9 V, IOUT = 500 mA VDIF(min)2 VIN = 2.0 V, IOUT = 1 000 mA VCONTH VCONTL VIN = 2.8 V VIN = 2.8 V
Note) The following values are typical and not guaranteed values.
Parameter Ripple rejection ratio 2 Output noise voltage Output voltage temperature coefficient Output short-circuit current Overheat protection operating temperature
Symbol RR2 VNO dVOUT dTa IOSHORT TjTH
Conditions VIN = 3.8 V ± 1 V[p-p], COUT = 33 +0.1 µF f = 500 kHz, IOUT = 100 mA 10 Hz ≤ f ≤ 100 kHz, IOUT = 100 mA CNR = 1 µF, VIN = 2.8 V VIN = 2.8 V, IOUT = 5 mA −30°C ≤ Ta ≤ +125°C VIN = 14.0 V, VOUT = GND VIN = 2.8 V, IOUT = 5 mA
Min
Typ 30 40 ±40 2 000 150
Max
Unit dB µV[rms] ppm/°C mA °C
4
SFF00010CEB
AN80PxxRSP Series
I Electrical Characteristics at Ta = 25°C (continued)
• AN80P19RSP (1.9 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 100 µF, CNR = Open, COUT = 0.1 µF Parameter Output voltage Line regulation Load regulation Peak output current Symbol VOUT REGIN IPEAK Conditions VIN = 2.9 V, IOUT = 500 mA VIN = 2.9 V → 14.0 V, IOUT = 250 mA Min 1.843 Typ 1.9 Max 1.957 19 38 Unit V mV mV mA
REGLOA VIN = 2.9 V, IOUT = 0 mA → 1 000 mA
VIN = 2.9 V, The output current value 1 200 when VOUT decreases by 5% from its value at IOUT = 500 mA. VIN = 2.9 V, IOUT = 0 mA −5 58.4 0.50
Bias current under no load Bias current fluctuation to input Bias current fluctuation to load Standby consumption current Bias current before starting regulation Control terminal current Ripple rejection ratio 1 Minimum input/ output voltage difference 1 Minimum input/ output voltage difference 2 Control terminal threshold high voltage Control terminal threshold low voltage • Design reference data
IBIAS
1.1 0.30 1.45 0.70
3.0 5 50 3.0 5 30 0.60 1.0 1.80
mA mA mA µA mA µA dB V V V V
∆IBIAS(IN) VIN = 2.9 V → 14.0 V, IOUT = 250 mA ∆IBIAS(LOA) VIN = 2.9 V, IOUT = 0 mA → 1 000 mA ISTB IRUSH ICONT RR1 VIN = 14.0 V, VCONT = 0 V VIN = 1.805 V, IOUT = 0 A VIN = 2.9 V, IOUT = 500 mA VCONT = 1.8 V VIN = 3.9 V ± 1 V[p-p] f = 120 Hz, IOUT = 100 mA
VDIF(min)1 VIN = 2.0 V, IOUT = 500 mA VDIF(min)2 VIN = 2.1 V, IOUT = 1 000 mA VCONTH VCONTL VIN = 2.9 V VIN = 2.9 V
Note) The following values are typical and not guaranteed values.
Parameter Ripple rejection ratio 2 Output noise voltage Output voltage temperature coefficient Output short-circuit current Overheat protection operating temperature
Symbol RR2 VNO dVOUT dTa IOSHORT TjTH
Conditions VIN = 3.9 V ± 1 V[p-p], COUT = 33 +0.1 µF f = 500 kHz, IOUT = 100 mA 10 Hz ≤ f ≤ 100 kHz, IOUT = 100 mA CNR = 1 µF, VIN = 2.9 V VIN = 2.9 V, IOUT = 5 mA −30°C ≤ Ta ≤ +125°C VIN = 14.0 V, VOUT = GND VIN = 2.9 V, IOUT = 5 mA
Min
Typ 30 40 ±40 2 000 150
Max
Unit dB µV[rms] ppm/°C mA °C
SFF00010CEB
5
AN80PxxRSP Series
I Electrical Characteristics at Ta = 25°C (continued)
• AN80P20RSP (2.0 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 100 µF, CNR = Open, COUT = 0.1 µF Parameter Output voltage Line regulation Load regulation Peak output current Symbol VOUT REGIN IPEAK Conditions VIN = 3.0 V, IOUT = 500 mA VIN = 3.0 V → 14.0 V, IOUT = 250 mA Min 1.940 Typ 2.0 Max 2.060 20 40 Unit V mV mV mA
REGLOA VIN = 3.0 V, IOUT = 0 mA → 1 000 mA
VIN = 3.0 V, The output current value 1 200 when VOUT decreases by 5% from its value at IOUT = 500 mA. VIN = 3.0 V, IOUT = 0 mA −5 57.9 0.50
Bias current under no load Bias current fluctuation to input Bias current fluctuation to load Standby consumption current Bias current before starting regulation Control terminal current Ripple rejection ratio 1 Minimum input/ output voltage difference 1 Minimum input/ output voltage difference 2 Control terminal threshold high voltage Control terminal threshold low voltage • Design reference data
IBIAS
1.1 0.30 1.45 0.70
3.0 5 50 3.0 5 30 0.60 1.0 1.80
mA mA mA µA mA µA dB V V V V
∆IBIAS(IN) VIN = 3.0 V → 14.0 V, IOUT = 250 mA ∆IBIAS(LOA) VIN = 3.0 V, IOUT = 0 mA → 1 000 mA ISTB IRUSH ICONT RR1 VIN = 14.0 V, VCONT = 0 V VIN = 1.900 V, IOUT = 0 A VIN = 3.0 V, IOUT = 500 mA VCONT = 1.8 V VIN = 4.0 V ± 1 V[p-p] f = 120 Hz, IOUT = 100 mA
VDIF(min)1 VIN = 2.1 V, IOUT = 500 mA VDIF(min)2 VIN = 2.2 V, IOUT = 1 000 mA VCONTH VCONTL VIN = 3.0 V VIN = 3.0 V
Note) The following values are typical and not guaranteed values.
Parameter Ripple rejection ratio 2 Output noise voltage Output voltage temperature coefficient Output short-circuit current Overheat protection operating temperature
Symbol RR2 VNO dVOUT dTa IOSHORT TjTH
Conditions VIN = 4.0 V ± 1 V[p-p], COUT = 33 +0.1 µF f = 500 kHz, IOUT = 100 mA 10 Hz ≤ f ≤ 100 kHz, IOUT = 100 mA CNR = 1 µF, VIN = 3.0 V VIN = 3.0 V, IOUT = 5 mA −30°C ≤ Ta ≤ +125°C VIN = 14.0 V, VOUT = GND VIN = 3.0 V, IOUT = 5 mA
Min
Typ 30 40 ±40 2 000 150
Max
Unit dB µV[rms] ppm/°C mA °C
6
SFF00010CEB
AN80PxxRSP Series
I Electrical Characteristics at Ta = 25°C (continued)
• AN80P21RSP (2.1 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 100 µF, CNR = Open, COUT = 0.1 µF Parameter Output voltage Line regulation Load regulation Peak output current Symbol VOUT REGIN IPEAK Conditions VIN = 3.1 V, IOUT = 500 mA VIN = 3.1 V → 14.0 V, IOUT = 250 mA Min 2.037 Typ 2.1 Max 2.163 21 42 Unit V mV mV mA
REGLOA VIN = 3.1 V, IOUT = 0 mA → 1 000 mA
VIN = 3.1 V, The output current value 1 200 when VOUT decreases by 5% from its value at IOUT = 500 mA. VIN = 3.1 V, IOUT = 0 mA −5 57.5 0.50
Bias current under no load Bias current fluctuation to input Bias current fluctuation to load Standby consumption current Bias current before starting regulation Control terminal current Ripple rejection ratio 1 Minimum input/ output voltage difference 1 Minimum input/ output voltage difference 2 Control terminal threshold high voltage Control terminal threshold low voltage • Design reference data
IBIAS
1.1 0.30 1.45 0.70
3.0 5 50 3.0 5 30 0.60 1.0 1.80
mA mA mA µA mA µA dB V V V V
∆IBIAS(IN) VIN = 3.1 V → 14.0 V, IOUT = 250 mA ∆IBIAS(LOA) VIN = 3.1 V, IOUT = 0 mA → 1 000 mA ISTB IRUSH ICONT RR1 VIN = 14.0 V, VCONT = 0 V VIN = 1.995 V, IOUT = 0 A VIN = 3.1 V, IOUT = 500 mA VCONT = 1.8 V VIN = 4.1 V ± 1 V[p-p] f = 120 Hz, IOUT = 100 mA
VDIF(min)1 VIN = 2.2 V, IOUT = 500 mA VDIF(min)2 VIN = 2.3 V, IOUT = 1 000 mA VCONTH VCONTL VIN = 3.1 V VIN = 3.1 V
Note) The following values are typical and not guaranteed values.
Parameter Ripple rejection ratio 2 Output noise voltage Output voltage temperature coefficient Output short-circuit current Overheat protection operating temperature
Symbol RR2 VNO dVOUT dTa IOSHORT TjTH
Conditions VIN = 4.1 V ± 1 V[p-p], COUT = 33 +0.1 µF f = 500 kHz, IOUT = 100 mA 10 Hz ≤ f ≤ 100 kHz, IOUT = 100 mA CNR = 1 µF, VIN = 3.1 V VIN = 3.1 V, IOUT = 5 mA −30°C ≤ Ta ≤ +125°C VIN = 14.0 V, VOUT = GND VIN = 3.1 V, IOUT = 5 mA
Min
Typ 30 40 ±40 2 000 150
Max
Unit dB µV[rms] ppm/°C mA °C
SFF00010CEB
7
AN80PxxRSP Series
I Electrical Characteristics at Ta = 25°C (continued)
• AN80P22RSP (2.2 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 100 µF, CNR = Open, COUT = 0.1 µF Parameter Output voltage Line regulation Load regulation Peak output current Symbol VOUT REGIN IPEAK Conditions VIN = 3.2 V, IOUT = 500 mA VIN = 3.2 V → 14.0 V, IOUT = 250 mA Min 2.134 Typ 2.2 Max 2.266 22 44 Unit V mV mV mA
REGLOA VIN = 3.2 V, IOUT = 0 mA → 1 000 mA
VIN = 3.2 V, The output current value 1 200 when VOUT decreases by 5% from its value at IOUT = 500 mA. VIN = 3.2 V, IOUT = 0 mA −5 57.1 0.50
Bias current under no load Bias current fluctuation to input Bias current fluctuation to load Standby consumption current Bias current before starting regulation Control terminal current Ripple rejection ratio 1 Minimum input/ output voltage difference 1 Minimum input/ output voltage difference 2 Control terminal threshold high voltage Control terminal threshold low voltage • Design reference data
IBIAS
1.1 0.30 1.45 0.70
3.0 5 50 3.0 5 30 0.60 1.0 1.80
mA mA mA µA mA µA dB V V V V
∆IBIAS(IN) VIN = 3.2 V → 14.0 V, IOUT = 250 mA ∆IBIAS(LOA) VIN = 3.2 V, IOUT = 0 mA → 1 000 mA ISTB IRUSH ICONT RR1 VIN = 14.0 V, VCONT = 0 V VIN = 2.090 V, IOUT = 0 A VIN = 3.2 V, IOUT = 500 mA VCONT = 1.8 V VIN = 4.2 V ± 1 V[p-p] f = 120 Hz, IOUT = 100 mA
VDIF(min)1 VIN = 2.3 V, IOUT = 500 mA VDIF(min)2 VIN = 2.4 V, IOUT = 1 000 mA VCONTH VCONTL VIN = 3.2 V VIN = 3.2 V
Note) The following values are typical and not guaranteed values.
Parameter Ripple rejection ratio 2 Output noise voltage Output voltage temperature coefficient Output short-circuit current Overheat protection operating temperature
Symbol RR2 VNO dVOUT dTa IOSHORT TjTH
Conditions VIN = 4.2 V ± 1 V[p-p], COUT = 33 +0.1 µF f = 500 kHz, IOUT = 100 mA 10 Hz ≤ f ≤ 100 kHz, IOUT = 100 mA CNR = 1 µF, VIN = 3.2 V VIN = 3.2 V, IOUT = 5 mA −30°C ≤ Ta ≤ +125°C VIN = 14.0 V, VOUT = GND VIN = 3.2 V, IOUT = 5 mA
Min
Typ 30 40 ±40 2 000 150
Max
Unit dB µV[rms] ppm/°C mA °C
8
SFF00010CEB
AN80PxxRSP Series
I Electrical Characteristics at Ta = 25°C (continued)
• AN80P25RSP (2.5 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 100 µF, CNR = Open, COUT = 0.1 µF Parameter Output voltage Line regulation Load regulation Peak output current Symbol VOUT REGIN IPEAK Conditions VIN = 3.5 V, IOUT = 500 mA VIN = 3.5 V → 14.0 V, IOUT = 250 mA Min 2.425 Typ 2.5 Max 2.575 25 50 Unit V mV mV mA
REGLOA VIN = 3.5 V, IOUT = 0 mA → 1 000 mA
VIN = 3.5 V, The output current value 1 200 when VOUT decreases by 5% from its value at IOUT = 500 mA. VIN = 3.5 V, IOUT = 0 mA −5 56.0 0.50
Bias current under no load Bias current fluctuation to input Bias current fluctuation to load Standby consumption current Bias current before starting regulation Control terminal current Ripple rejection ratio 1 Minimum input/ output voltage difference 1 Minimum input/ output voltage difference 2 Control terminal threshold high voltage Control terminal threshold low voltage • Design reference data
IBIAS
1.1 0.30 1.45 0.70
3.0 5 50 3.0 5 30 0.60 1.0 1.80
mA mA mA µA mA µA dB V V V V
∆IBIAS(IN) VIN = 3.5 V → 14.0 V, IOUT = 250 mA ∆IBIAS(LOA) VIN = 3.5 V, IOUT = 0 mA → 1 000 mA ISTB IRUSH ICONT RR1 VIN = 14.0 V, VCONT = 0 V VIN = 2.375 V, IOUT = 0 A VIN = 3.5 V, IOUT = 500 mA VCONT = 1.8 V VIN = 4.5 V ± 1 V[p-p] f = 120 Hz, IOUT = 100 mA
VDIF(min)1 VIN = 2.6 V, IOUT = 500 mA VDIF(min)2 VIN = 2.7 V, IOUT = 1 000 mA VCONTH VCONTL VIN = 3.5 V VIN = 3.5 V
Note) The following values are typical and not guaranteed values.
Parameter Ripple rejection ratio 2 Output noise voltage Output voltage temperature coefficient Output short-circuit current Overheat protection operating temperature
Symbol RR2 VNO dVOUT dTa IOSHORT TjTH
Conditions VIN = 4.5 V ± 1 V[p-p], COUT = 33 +0.1 µF f = 500 kHz, IOUT = 100 mA 10 Hz ≤ f ≤ 100 kHz, IOUT = 100 mA CNR = 1 µF, VIN = 3.5 V VIN = 3.5 V, IOUT = 5 mA −30°C ≤ Ta ≤ +125°C VIN = 14.0 V, VOUT = GND VIN = 3.5 V, IOUT = 5 mA
Min
Typ 30 40 ±40 2 000 150
Max
Unit dB µV[rms] ppm/°C mA °C
SFF00010CEB
9
AN80PxxRSP Series
I Electrical Characteristics at Ta = 25°C (continued)
• AN80P27RSP (2.7 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 100 µF, CNR = Open, COUT = 0.1 µF Parameter Output voltage Line regulation Load regulation Peak output current Symbol VOUT REGIN IPEAK Conditions VIN = 3.7 V, IOUT = 500 mA VIN = 3.7 V → 14.0 V, IOUT = 250 mA Min 2.619 Typ 2.7 Max 2.781 27 54 Unit V mV mV mA
REGLOA VIN = 3.7 V, IOUT = 0 mA → 1 000 mA
VIN = 3.7 V, The output current value 1 200 when VOUT decreases by 5% from its value at IOUT = 500 mA. VIN = 3.7 V, IOUT = 0 mA −5 55.3 0.50
Bias current under no load Bias current fluctuation to input Bias current fluctuation to load Standby consumption current Bias current before starting regulation Control terminal current Ripple rejection ratio 1 Minimum input/ output voltage difference 1 Minimum input/ output voltage difference 2 Control terminal threshold high voltage Control terminal threshold low voltage • Design reference data
IBIAS
1.1 0.30 1.45 0.70
3.0 5 50 3.0 5 30 0.60 1.0 1.80
mA mA mA µA mA µA dB V V V V
∆IBIAS(IN) VIN = 3.7 V → 14.0 V, IOUT = 250 mA ∆IBIAS(LOA) VIN = 3.7 V, IOUT = 0 mA → 1 000 mA ISTB IRUSH ICONT RR1 VIN = 14.0 V, VCONT = 0 V VIN = 2.565 V, IOUT = 0 A VIN = 3.7 V, IOUT = 500 mA VCONT = 1.8 V VIN = 4.7 V ± 1 V[p-p] f = 120 Hz, IOUT = 100 mA
VDIF(min)1 VIN = 2.8 V, IOUT = 500 mA VDIF(min)2 VIN = 2.9 V, IOUT = 1 000 mA VCONTH VCONTL VIN = 3.7 V VIN = 3.7 V
Note) The following values are typical and not guaranteed values.
Parameter Ripple rejection ratio 2 Output noise voltage Output voltage temperature coefficient Output short-circuit current Overheat protection operating temperature
Symbol RR2 VNO dVOUT dTa IOSHORT TjTH
Conditions VIN = 4.7 V ± 1 V[p-p], COUT = 33 +0.1 µF f = 500 kHz, IOUT = 100 mA 10 Hz ≤ f ≤ 100 kHz, IOUT = 100 mA CNR = 1 µF, VIN = 3.7 V VIN = 3.7 V, IOUT = 5 mA −30°C ≤ Ta ≤ +125°C VIN = 14.0 V, VOUT = GND VIN = 3.7 V, IOUT = 5 mA
Min
Typ 30 40 ±40 2 000 150
Max
Unit dB µV[rms] ppm/°C mA °C
10
SFF00010CEB
AN80PxxRSP Series
I Electrical Characteristics at Ta = 25°C (continued)
• AN80P28RSP (2.8 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 100 µF, CNR = Open, COUT = 0.1 µF Parameter Output voltage Line regulation Load regulation Peak output current Symbol VOUT REGIN IPEAK Conditions VIN = 3.8 V, IOUT = 500 mA VIN = 3.8 V → 14.0 V, IOUT = 250 mA Min 2.716 Typ 2.8 Max 2.884 28 56 Unit V mV mV mA
REGLOA VIN = 3.8 V, IOUT = 0 mA → 1 000 mA
VIN = 3.8 V, The output current value 1 200 when VOUT decreases by 5% from its value at IOUT = 500 mA. VIN = 3.8 V, IOUT = 0 mA −5 55.0 0.50
Bias current under no load Bias current fluctuation to input Bias current fluctuation to load Standby consumption current Bias current before starting regulation Control terminal current Ripple rejection ratio 1 Minimum input/ output voltage difference 1 Minimum input/ output voltage difference 2 Control terminal threshold high voltage Control terminal threshold low voltage • Design reference data
IBIAS
1.1 0.30 1.45 0.70
3.0 5 50 3.0 5 30 0.60 1.0 1.80
mA mA mA µA mA µA dB V V V V
∆IBIAS(IN) VIN = 3.8 V → 14.0 V, IOUT = 250 mA ∆IBIAS(LOA) VIN = 3.8 V, IOUT = 0 mA → 1 000 mA ISTB IRUSH ICONT RR1 VIN = 14.0 V, VCONT = 0 V VIN = 2.660 V, IOUT = 0 A VIN = 3.8 V, IOUT = 500 mA VCONT = 1.8 V VIN = 4.8 V ± 1 V[p-p] f = 120 Hz, IOUT = 100 mA
VDIF(min)1 VIN = 2.9 V, IOUT = 500 mA VDIF(min)2 VIN = 3.0 V, IOUT = 1 000 mA VCONTH VCONTL VIN = 3.8 V VIN = 3.8 V
Note) The following values are typical and not guaranteed values.
Parameter Ripple rejection ratio 2 Output noise voltage Output voltage temperature coefficient Output short-circuit current Overheat protection operating temperature
Symbol RR2 VNO dVOUT dTa IOSHORT TjTH
Conditions VIN = 4.8 V ± 1 V[p-p], COUT = 33 +0.1 µF f = 500 kHz, IOUT = 100 mA 10 Hz ≤ f ≤ 100 kHz, IOUT = 100 mA CNR = 1 µF, VIN = 3.8 V VIN = 3.8 V, IOUT = 5 mA −30°C ≤ Ta ≤ +125°C VIN = 14.0 V, VOUT = GND VIN = 3.8 V, IOUT = 5 mA
Min
Typ 30 40 ±40 2 000 150
Max
Unit dB µV[rms] ppm/°C mA °C
SFF00010CEB
11
AN80PxxRSP Series
I Electrical Characteristics at Ta = 25°C (continued)
• AN80P29RSP (2.9 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 100 µF, CNR = Open, COUT = 0.1 µF Parameter Output voltage Line regulation Load regulation Peak output current Symbol VOUT REGIN IPEAK Conditions VIN = 3.9 V, IOUT = 500 mA VIN = 3.9 V → 14.0 V, IOUT = 250 mA Min 2.813 Typ 2.9 Max 2.987 29 58 Unit V mV mV mA
REGLOA VIN = 3.9 V, IOUT = 0 mA → 1 000 mA
VIN = 3.9 V, The output current value 1 200 when VOUT decreases by 5% from its value at IOUT = 500 mA. VIN = 3.9 V, IOUT = 0 mA −5 54.7 0.50
Bias current under no load Bias current fluctuation to input Bias current fluctuation to load Standby consumption current Bias current before starting regulation Control terminal current Ripple rejection ratio 1 Minimum input/ output voltage difference 1 Minimum input/ output voltage difference 2 Control terminal threshold high voltage Control terminal threshold low voltage • Design reference data
IBIAS
1.1 0.30 1.45 0.70
3.0 5 50 3.0 5 30 0.60 1.0 1.80
mA mA mA µA mA µA dB V V V V
∆IBIAS(IN) VIN = 3.9 V → 14.0 V, IOUT = 250 mA ∆IBIAS(LOA) VIN = 3.9 V, IOUT = 0 mA → 1 000 mA ISTB IRUSH ICONT RR1 VIN = 14.0 V, VCONT = 0 V VIN = 2.755 V, IOUT = 0 A VIN = 3.9 V, IOUT = 500 mA VCONT = 1.8 V VIN = 4.9 V ± 1 V[p-p] f = 120 Hz, IOUT = 100 mA
VDIF(min)1 VIN = 3.0 V, IOUT = 500 mA VDIF(min)2 VIN = 3.1 V, IOUT = 1 000 mA VCONTH VCONTL VIN = 3.9 V VIN = 3.9 V
Note) The following values are typical and not guaranteed values.
Parameter Ripple rejection ratio 2 Output noise voltage Output voltage temperature coefficient Output short-circuit current Overheat protection operating temperature
Symbol RR2 VNO dVOUT dTa IOSHORT TjTH
Conditions VIN = 4.9 V ± 1 V[p-p], COUT = 33 +0.1 µF f = 500 kHz, IOUT = 100 mA 10 Hz ≤ f ≤ 100 kHz, IOUT = 100 mA CNR = 1 µF, VIN = 3.9 V VIN = 3.9 V, IOUT = 5 mA −30°C ≤ Ta ≤ +125°C VIN = 14.0 V, VOUT = GND VIN = 3.9 V, IOUT = 5 mA
Min
Typ 30 40 ±40 2 000 150
Max
Unit dB µV[rms] ppm/°C mA °C
12
SFF00010CEB
AN80PxxRSP Series
I Electrical Characteristics at Ta = 25°C (continued)
• AN80P30RSP (3.0 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 100 µF, CNR = Open, COUT = 0.1 µF Parameter Output voltage Line regulation Load regulation Peak output current Symbol VOUT REGIN IPEAK Conditions VIN = 4.0 V, IOUT = 500 mA VIN = 4.0 V → 14.0 V, IOUT = 250 mA Min 2.910 Typ 3.0 Max 3.090 30 60 Unit V mV mV mA
REGLOA VIN = 4.0 V, IOUT = 0 mA → 1 000 mA
VIN = 4.0 V, The output current value 1 200 when VOUT decreases by 5% from its value at IOUT = 500 mA. VIN = 4.0 V, IOUT = 0 mA −5 54.1 0.50
Bias current under no load Bias current fluctuation to input Bias current fluctuation to load Standby consumption current Bias current before starting regulation Control terminal current Ripple rejection ratio 1 Minimum input/ output voltage difference 1 Minimum input/ output voltage difference 2 Control terminal threshold high voltage Control terminal threshold low voltage • Design reference data
IBIAS
1.1 0.30 1.45 0.70
3.0 5 50 3.0 5 30 0.60 1.0 1.80
mA mA mA µA mA µA dB V V V V
∆IBIAS(IN) VIN = 4.0 V → 14.0 V, IOUT = 250 mA ∆IBIAS(LOA) VIN = 4.0 V, IOUT = 0 mA → 1 000 mA ISTB IRUSH ICONT RR1 VIN = 14.0 V, VCONT = 0 V VIN = 2.850 V, IOUT = 0 A VIN = 4.0 V, IOUT = 500 mA VCONT = 1.8 V VIN = 5.0 V ± 1 V[p-p] f = 120 Hz, IOUT = 100 mA
VDIF(min)1 VIN = 3.1 V, IOUT = 500 mA VDIF(min)2 VIN = 3.2 V, IOUT = 1 000 mA VCONTH VCONTL VIN = 4.0 V VIN = 4.0 V
Note) The following values are typical and not guaranteed values.
Parameter Ripple rejection ratio 2 Output noise voltage Output voltage temperature coefficient Output short-circuit current Overheat protection operating temperature
Symbol RR2 VNO dVOUT dTa IOSHORT TjTH
Conditions VIN = 5.0 V ± 1 V[p-p], COUT = 33 +0.1 µF f = 500 kHz, IOUT = 100 mA 10 Hz ≤ f ≤ 100 kHz, IOUT = 100 mA CNR = 1 µF, VIN = 4.0 V VIN = 4.0 V, IOUT = 5 mA −30°C ≤ Ta ≤ +125°C VIN = 14.0 V, VOUT = GND VIN = 4.0 V, IOUT = 5 mA
Min
Typ 30 40 ±40 2 000 150
Max
Unit dB µV[rms] ppm/°C mA °C
SFF00010CEB
13
AN80PxxRSP Series
I Electrical Characteristics at Ta = 25°C (continued)
• AN80P31RSP (3.1 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 100 µF, CNR = Open, COUT = 0.1 µF Parameter Output voltage Line regulation Load regulation Peak output current Symbol VOUT REGIN IPEAK Conditions VIN = 4.1 V, IOUT = 500 mA VIN = 4.1 V → 14.0 V, IOUT = 250 mA Min 3.007 Typ 3.1 Max 3.193 31 62 Unit V mV mV mA
REGLOA VIN = 4.1 V, IOUT = 0 mA → 1 000 mA
VIN = 4.1 V, The output current value 1 200 when VOUT decreases by 5% from its value at IOUT = 500 mA. VIN = 4.1 V, IOUT = 0 mA −5 54.1 0.50
Bias current under no load Bias current fluctuation to input Bias current fluctuation to load Standby consumption current Bias current before starting regulation Control terminal current Ripple rejection ratio 1 Minimum input/ output voltage difference 1 Minimum input/ output voltage difference 2 Control terminal threshold high voltage Control terminal threshold low voltage • Design reference data
IBIAS
1.1 0.30 1.45 0.70
3.0 5 50 3.0 5 30 0.60 1.0 1.80
mA mA mA µA mA µA dB V V V V
∆IBIAS(IN) VIN = 4.1 V → 14.0 V, IOUT = 250 mA ∆IBIAS(LOA) VIN = 4.1 V, IOUT = 0 mA → 1 000 mA ISTB IRUSH ICONT RR1 VIN = 14.0 V, VCONT = 0 V VIN = 2.945 V, IOUT = 0 A VIN = 4.1 V, IOUT = 500 mA VCONT = 1.8 V VIN = 5.1 V ± 1 V[p-p] f = 120 Hz, IOUT = 100 mA
VDIF(min)1 VIN = 3.2 V, IOUT = 500 mA VDIF(min)2 VIN = 3.3 V, IOUT = 1 000 mA VCONTH VCONTL VIN = 4.1 V VIN = 4.1 V
Note) The following values are typical and not guaranteed values.
Parameter Ripple rejection ratio 2 Output noise voltage Output voltage temperature coefficient Output short-circuit current Overheat protection operating temperature
Symbol RR2 VNO dVOUT dTa IOSHORT TjTH
Conditions VIN = 5.1 V ± 1 V[p-p], COUT = 33 +0.1 µF f = 500 kHz, IOUT = 100 mA 10 Hz ≤ f ≤ 100 kHz, IOUT = 100 mA CNR = 1 µF, VIN = 4.1 V VIN = 4.1 V, IOUT = 5 mA −30°C ≤ Ta ≤ +125°C VIN = 14.0 V, VOUT = GND VIN = 4.1 V, IOUT = 5 mA
Min
Typ 30 40 ±40 2 000 150
Max
Unit dB µV[rms] ppm/°C mA °C
14
SFF00010CEB
AN80PxxRSP Series
I Electrical Characteristics at Ta = 25°C (continued)
• AN80P32RSP (3.2 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 100 µF, CNR = Open, COUT = 0.1 µF Parameter Output voltage Line regulation Load regulation Peak output current Symbol VOUT REGIN IPEAK Conditions VIN = 4.2 V, IOUT = 500 mA VIN = 4.2 V → 14.0 V, IOUT = 250 mA Min 3.104 Typ 3.2 Max 3.296 32 64 Unit V mV mV mA
REGLOA VIN = 4.2 V, IOUT = 0 mA → 1 000 mA
VIN = 4.2 V, The output current value 1 200 when VOUT decreases by 5% from its value at IOUT = 500 mA. VIN = 4.2 V, IOUT = 0 mA −5 53.8 0.50
Bias current under no load Bias current fluctuation to input Bias current fluctuation to load Standby consumption current Bias current before starting regulation Control terminal current Ripple rejection ratio 1 Minimum input/ output voltage difference 1 Minimum input/ output voltage difference 2 Control terminal threshold high voltage Control terminal threshold low voltage • Design reference data
IBIAS
1.1 0.30 1.45 0.70
3.0 5 50 3.0 5 30 0.60 1.0 1.80
mA mA mA µA mA µA dB V V V V
∆IBIAS(IN) VIN = 4.2 V → 14.0 V, IOUT = 250 mA ∆IBIAS(LOA) VIN = 4.2 V, IOUT = 0 mA → 1 000 mA ISTB IRUSH ICONT RR1 VIN = 14.0 V, VCONT = 0 V VIN = 3.040 V, IOUT = 0 A VIN = 4.2 V, IOUT = 500 mA VCONT = 1.8 V VIN = 5.2 V ± 1 V[p-p] f = 120 Hz, IOUT = 100 mA
VDIF(min)1 VIN = 3.3 V, IOUT = 500 mA VDIF(min)2 VIN = 3.4 V, IOUT = 1 000 mA VCONTH VCONTL VIN = 4.2 V VIN = 4.2 V
Note) The following values are typical and not guaranteed values.
Parameter Ripple rejection ratio 2 Output noise voltage Output voltage temperature coefficient Output short-circuit current Overheat protection operating temperature
Symbol RR2 VNO dVOUT dTa IOSHORT TjTH
Conditions VIN = 5.2 V ± 1 V[p-p], COUT = 33 +0.1 µF f = 500 kHz, IOUT = 100 mA 10 Hz ≤ f ≤ 100 kHz, IOUT = 100 mA CNR = 1 µF, VIN = 4.2 V VIN = 4.2 V, IOUT = 5 mA −30°C ≤ Ta ≤ +125°C VIN = 14.0 V, VOUT = GND VIN = 4.2 V, IOUT = 5 mA
Min
Typ 30 40 ±40 2 000 150
Max
Unit dB µV[rms] ppm/°C mA °C
SFF00010CEB
15
AN80PxxRSP Series
I Electrical Characteristics at Ta = 25°C (continued)
• AN80P33RSP (3.3 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 100 µF, CNR = Open, COUT = 0.1 µF Parameter Output voltage Line regulation Load regulation Peak output current Symbol VOUT REGIN IPEAK Conditions VIN = 4.3 V, IOUT = 500 mA VIN = 4.3 V → 14.0 V, IOUT = 250 mA Min 3.201 Typ 3.3 Max 3.399 33 66 Unit V mV mV mA
REGLOA VIN = 4.3 V, IOUT = 0 mA → 1 000 mA
VIN = 4.3 V, The output current value 1 200 when VOUT decreases by 5% from its value at IOUT = 500 mA. VIN = 4.3 V, IOUT = 0 mA −5 53.6 0.50
Bias current under no load Bias current fluctuation to input Bias current fluctuation to load Standby consumption current Bias current before starting regulation Control terminal current Ripple rejection ratio 1 Minimum input/ output voltage difference 1 Minimum input/ output voltage difference 2 Control terminal threshold high voltage Control terminal threshold low voltage • Design reference data
IBIAS
1.1 0.30 1.45 0.70
3.0 5 50 3.0 5 30 0.60 1.0 1.80
mA mA mA µA mA µA dB V V V V
∆IBIAS(IN) VIN = 4.3 V → 14.0 V, IOUT = 250 mA ∆IBIAS(LOA) VIN = 4.3 V, IOUT = 0 mA → 1 000 mA ISTB IRUSH ICONT RR1 VIN = 14.0 V, VCONT = 0 V VIN = 3.135 V, IOUT = 0 A VIN = 4.3 V, IOUT = 500 mA VCONT = 1.8 V VIN = 5.3 V ± 1 V[p-p] f = 120 Hz, IOUT = 100 mA
VDIF(min)1 VIN = 3.4 V, IOUT = 500 mA VDIF(min)2 VIN = 3.5 V, IOUT = 1 000 mA VCONTH VCONTL VIN = 4.3 V VIN = 4.3 V
Note) The following values are typical and not guaranteed values.
Parameter Ripple rejection ratio 2 Output noise voltage Output voltage temperature coefficient Output short-circuit current Overheat protection operating temperature
Symbol RR2 VNO dVOUT dTa IOSHORT TjTH
Conditions VIN = 5.3 V ± 1 V[p-p], COUT = 33 +0.1 µF f = 500 kHz, IOUT = 100 mA 10 Hz ≤ f ≤ 100 kHz, IOUT = 100 mA CNR = 1 µF, VIN = 4.3 V VIN = 4.3 V, IOUT = 5 mA −30°C ≤ Ta ≤ +125°C VIN = 14.0 V, VOUT = GND VIN = 4.3 V, IOUT = 5 mA
Min
Typ 30 40 ±40 2 000 150
Max
Unit dB µV[rms] ppm/°C mA °C
16
SFF00010CEB
AN80PxxRSP Series
I Electrical Characteristics at Ta = 25°C (continued)
• AN80P34RSP (3.4 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 100 µF, CNR = Open, COUT = 0.1 µF Parameter Output voltage Line regulation Load regulation Peak output current Symbol VOUT REGIN IPEAK Conditions VIN = 4.4 V, IOUT = 500 mA VIN = 4.4 V → 14.0 V, IOUT = 250 mA Min 3.298 Typ 3.4 Max 3.502 34 68 Unit V mV mV mA
REGLOA VIN = 4.4 V, IOUT = 0 mA → 1 000 mA
VIN = 4.4 V, The output current value 1 200 when VOUT decreases by 5% from its value at IOUT = 500 mA. VIN = 4.4 V, IOUT = 0 mA −5 53.3 0.50
Bias current under no load Bias current fluctuation to input Bias current fluctuation to load Standby consumption current Bias current before starting regulation Control terminal current Ripple rejection ratio 1 Minimum input/ output voltage difference 1 Minimum input/ output voltage difference 2 Control terminal threshold high voltage Control terminal threshold low voltage • Design reference data
IBIAS
1.1 0.30 1.45 0.70
3.0 5 50 3.0 5 30 0.60 1.0 1.80
mA mA mA µA mA µA dB V V V V
∆IBIAS(IN) VIN = 4.4 V → 14.0 V, IOUT = 250 mA ∆IBIAS(LOA) VIN = 4.4 V, IOUT = 0 mA → 1 000 mA ISTB IRUSH ICONT RR1 VIN = 14.0 V, VCONT = 0 V VIN = 3.230 V, IOUT = 0 A VIN = 4.4 V, IOUT = 500 mA VCONT = 1.8 V VIN = 5.4 V ± 1 V[p-p] f = 120 Hz, IOUT = 100 mA
VDIF(min)1 VIN = 3.5 V, IOUT = 500 mA VDIF(min)2 VIN = 3.6 V, IOUT = 1 000 mA VCONTH VCONTL VIN = 4.4 V VIN = 4.4 V
Note) The following values are typical and not guaranteed values.
Parameter Ripple rejection ratio 2 Output noise voltage Output voltage temperature coefficient Output short-circuit current Overheat protection operating temperature
Symbol RR2 VNO dVOUT dTa IOSHORT TjTH
Conditions VIN = 5.4 V ± 1 V[p-p], COUT = 33 +0.1 µF f = 500 kHz, IOUT = 100 mA 10 Hz ≤ f ≤ 100 kHz, IOUT = 100 mA CNR = 1 µF, VIN = 4.4 V VIN = 4.4 V, IOUT = 5 mA −30°C ≤ Ta ≤ +125°C VIN = 14.0 V, VOUT = GND VIN = 4.4 V, IOUT = 5 mA
Min
Typ 30 40 ±40 2 000 150
Max
Unit dB µV[rms] ppm/°C mA °C
SFF00010CEB
17
AN80PxxRSP Series
I Electrical Characteristics at Ta = 25°C (continued)
• AN80P35RSP (3.5 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 100 µF, CNR = Open, COUT = 0.1 µF Parameter Output voltage Line regulation Load regulation Peak output current Symbol VOUT REGIN IPEAK Conditions VIN = 4.5 V, IOUT = 500 mA VIN = 4.5 V → 14.0 V, IOUT = 250 mA Min 3.395 Typ 3.5 Max 3.605 35 70 Unit V mV mV mA
REGLOA VIN = 4.5 V, IOUT = 0 mA → 1 000 mA
VIN = 4.5 V, The output current value 1 200 when VOUT decreases by 5% from its value at IOUT = 500 mA. VIN = 4.5 V, IOUT = 0 mA −5 53.1 0.50
Bias current under no load Bias current fluctuation to input Bias current fluctuation to load Standby consumption current Bias current before starting regulation Control terminal current Ripple rejection ratio 1 Minimum input/ output voltage difference 1 Minimum input/ output voltage difference 2 Control terminal threshold high voltage Control terminal threshold low voltage • Design reference data
IBIAS
1.1 0.30 1.45 0.70
3.0 5 50 3.0 5 30 0.60 1.0 1.80
mA mA mA µA mA µA dB V V V V
∆IBIAS(IN) VIN = 4.5 V → 14.0 V, IOUT = 250 mA ∆IBIAS(LOA) VIN = 4.5 V, IOUT = 0 mA → 1 000 mA ISTB IRUSH ICONT RR1 VIN = 14.0 V, VCONT = 0 V VIN = 3.325 V, IOUT = 0 A VIN = 4.5 V, IOUT = 500 mA VCONT = 1.8 V VIN = 5.5 V ± 1 V[p-p] f = 120 Hz, IOUT = 100 mA
VDIF(min)1 VIN = 3.6 V, IOUT = 500 mA VDIF(min)2 VIN = 3.7 V, IOUT = 1 000 mA VCONTH VCONTL VIN = 4.5 V VIN = 4.5 V
Note) The following values are typical and not guaranteed values.
Parameter Ripple rejection ratio 2 Output noise voltage Output voltage temperature coefficient Output short-circuit current Overheat protection operating temperature
Symbol RR2 VNO dVOUT dTa IOSHORT TjTH
Conditions VIN = 5.5 V ± 1 V[p-p], COUT = 33 +0.1 µF f = 500 kHz, IOUT = 100 mA 10 Hz ≤ f ≤ 100 kHz, IOUT = 100 mA CNR = 1 µF, VIN = 4.5 V VIN = 4.5 V, IOUT = 5 mA −30°C ≤ Ta ≤ +125°C VIN = 14.0 V, VOUT = GND VIN = 4.5 V, IOUT = 5 mA
Min
Typ 30 40 ±40 2 000 150
Max
Unit dB µV[rms] ppm/°C mA °C
18
SFF00010CEB
AN80PxxRSP Series
I Electrical Characteristics at Ta = 25°C (continued)
• AN80P36RSP (3.6 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 100 µF, CNR = Open, COUT = 0.1 µF Parameter Output voltage Line regulation Load regulation Peak output current Symbol VOUT REGIN IPEAK Conditions VIN = 4.6 V, IOUT = 500 mA VIN = 4.6 V → 14.0 V, IOUT = 250 mA Min 3.492 Typ 3.6 Max 3.708 36 72 Unit V mV mV mA
REGLOA VIN = 4.6 V, IOUT = 0 mA → 1 000 mA
VIN = 4.6 V, The output current value 1 200 when VOUT decreases by 5% from its value at IOUT = 500 mA. VIN = 4.6 V, IOUT = 0 mA −5 52.8 0.50
Bias current under no load Bias current fluctuation to input Bias current fluctuation to load Standby consumption current Bias current before starting regulation Control terminal current Ripple rejection ratio 1 Minimum input/ output voltage difference 1 Minimum input/ output voltage difference 2 Control terminal threshold high voltage Control terminal threshold low voltage • Design reference data
IBIAS
1.1 0.30 1.45 0.70
3.0 5 50 3.0 5 30 0.60 1.0 1.80
mA mA mA µA mA µA dB V V V V
∆IBIAS(IN) VIN = 4.6 V → 14.0 V, IOUT = 250 mA ∆IBIAS(LOA) VIN = 4.6 V, IOUT = 0 mA → 1 000 mA ISTB IRUSH ICONT RR1 VIN = 14.0 V, VCONT = 0 V VIN = 3.420 V, IOUT = 0 A VIN = 4.6 V, IOUT = 500 mA VCONT = 1.8 V VIN = 5.6 V ± 1 V[p-p] f = 120 Hz, IOUT = 100 mA
VDIF(min)1 VIN = 3.7 V, IOUT = 500 mA VDIF(min)2 VIN = 3.8 V, IOUT = 1 000 mA VCONTH VCONTL VIN = 4.6 V VIN = 4.6 V
Note) The following values are typical and not guaranteed values.
Parameter Ripple rejection ratio 2 Output noise voltage Output voltage temperature coefficient Output short-circuit current Overheat protection operating temperature
Symbol RR2 VNO dVOUT dTa IOSHORT TjTH
Conditions VIN = 5.6 V ± 1 V[p-p], COUT = 33 +0.1 µF f = 500 kHz, IOUT = 100 mA 10 Hz ≤ f ≤ 100 kHz, IOUT = 100 mA CNR = 1 µF, VIN = 4.6 V VIN = 4.6 V, IOUT = 5 mA −30°C ≤ Ta ≤ +125°C VIN = 14.0 V, VOUT = GND VIN = 4.6 V, IOUT = 5 mA
Min
Typ 30 40 ±40 2 000 150
Max
Unit dB µV[rms] ppm/°C mA °C
SFF00010CEB
19
AN80PxxRSP Series
I Electrical Characteristics at Ta = 25°C (continued)
• AN80P48RSP (4.8 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 100 µF, CNR = Open, COUT = 0.1 µF Parameter Output voltage Line regulation Load regulation Peak output current Symbol VOUT REGIN IPEAK Conditions VIN = 5.8 V, IOUT = 500 mA VIN = 5.8 V → 14.0 V, IOUT = 250 mA Min 4.656 Typ 4.8 Max 4.944 48 96 Unit V mV mV mA
REGLOA VIN = 5.8 V, IOUT = 0 mA → 1 000 mA
VIN = 5.8 V, The output current value 1 200 when VOUT decreases by 5% from its value at IOUT = 500 mA. VIN = 5.8 V, IOUT = 0 mA −5 50.3 0.50
Bias current under no load Bias current fluctuation to input Bias current fluctuation to load Standby consumption current Bias current before starting regulation Control terminal current Ripple rejection ratio 1 Minimum input/ output voltage difference 1 Minimum input/ output voltage difference 2 Control terminal threshold high voltage Control terminal threshold low voltage • Design reference data
IBIAS
1.1 0.30 1.45 0.70
3.0 5 50 3.0 5 30 0.60 1.0 1.80
mA mA mA µA mA µA dB V V V V
∆IBIAS(IN) VIN = 5.8 V → 14.0 V, IOUT = 250 mA ∆IBIAS(LOA) VIN = 5.8 V, IOUT = 0 mA → 1 000 mA ISTB IRUSH ICONT RR1 VIN = 14.0 V, VCONT = 0 V VIN = 4.560 V, IOUT = 0 A VIN = 5.8 V, IOUT = 500 mA VCONT = 1.8 V VIN = 6.8 V ± 1 V[p-p] f = 120 Hz, IOUT = 100 mA
VDIF(min)1 VIN = 4.9 V, IOUT = 500 mA VDIF(min)2 VIN = 5.0 V, IOUT = 1 000 mA VCONTH VCONTL VIN = 5.8 V VIN = 5.8 V
Note) The following values are typical and not guaranteed values.
Parameter Ripple rejection ratio 2 Output noise voltage Output voltage temperature coefficient Output short-circuit current Overheat protection operating temperature
Symbol RR2 VNO dVOUT dTa IOSHORT TjTH
Conditions VIN = 6.8 V ± 1 V[p-p], COUT = 33 +0.1 µF f = 500 kHz, IOUT = 100 mA 10 Hz ≤ f ≤ 100 kHz, IOUT = 100 mA CNR = 1 µF, VIN = 5.8 V VIN = 5.8 V, IOUT = 5 mA −30°C ≤ Ta ≤ +125°C VIN = 14.0 V, VOUT = GND VIN = 5.8 V, IOUT = 5 mA
Min
Typ 30 40 ±40 2 000 150
Max
Unit dB µV[rms] ppm/°C mA °C
20
SFF00010CEB
AN80PxxRSP Series
I Electrical Characteristics at Ta = 25°C (continued)
• AN80P49RSP (4.9 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 100 µF, CNR = Open, COUT = 0.1 µF Parameter Output voltage Line regulation Load regulation Peak output current Symbol VOUT REGIN IPEAK Conditions VIN = 5.9 V, IOUT = 500 mA VIN = 5.9 V → 14.0 V, IOUT = 250 mA Min 4.753 Typ 4.9 Max 5.047 49 98 Unit V mV mV mA
REGLOA VIN = 5.9 V, IOUT = 0 mA → 1 000 mA
VIN = 5.9 V, The output current value 1 200 when VOUT decreases by 5% from its value at IOUT = 500 mA. VIN = 5.9 V, IOUT = 0 mA −5 50.1 0.50
Bias current under no load Bias current fluctuation to input Bias current fluctuation to load Standby consumption current Bias current before starting regulation Control terminal current Ripple rejection ratio 1 Minimum input/ output voltage difference 1 Minimum input/ output voltage difference 2 Control terminal threshold high voltage Control terminal threshold low voltage • Design reference data
IBIAS
1.1 0.30 1.45 0.70
3.0 5 50 3.0 5 30 0.60 1.0 1.80
mA mA mA µA mA µA dB V V V V
∆IBIAS(IN) VIN = 5.9 V → 14.0 V, IOUT = 250 mA ∆IBIAS(LOA) VIN = 5.9 V, IOUT = 0 mA → 1 000 mA ISTB IRUSH ICONT RR1 VIN = 14.0 V, VCONT = 0 V VIN = 4.655 V, IOUT = 0 A VIN = 5.9 V, IOUT = 500 mA VCONT = 1.8 V VIN = 6.9 V ± 1 V[p-p] f = 120 Hz, IOUT = 100 mA
VDIF(min)1 VIN = 5.0 V, IOUT = 500 mA VDIF(min)2 VIN = 5.1 V, IOUT = 1 000 mA VCONTH VCONTL VIN = 5.9 V VIN = 5.9 V
Note) The following values are typical and not guaranteed values.
Parameter Ripple rejection ratio 2 Output noise voltage Output voltage temperature coefficient Output short-circuit current Overheat protection operating temperature
Symbol RR2 VNO dVOUT dTa IOSHORT TjTH
Conditions VIN = 6.9 V ± 1 V[p-p], COUT = 33 +0.1 µF f = 500 kHz, IOUT = 100 mA 10 Hz ≤ f ≤ 100 kHz, IOUT = 100 mA CNR = 1 µF, VIN = 5.9 V VIN = 5.9 V, IOUT = 5 mA −30°C ≤ Ta ≤ +125°C VIN = 14.0 V, VOUT = GND VIN = 5.9 V, IOUT = 5 mA
Min
Typ 30 40 ±40 2 000 150
Max
Unit dB µV[rms] ppm/°C mA °C
SFF00010CEB
21
AN80PxxRSP Series
I Electrical Characteristics at Ta = 25°C (continued)
• AN80P50RSP (5.0 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 100 µF, CNR = Open, COUT = 0.1 µF Parameter Output voltage Line regulation Load regulation Peak output current Symbol VOUT REGIN IPEAK Conditions VIN = 6.0 V, IOUT = 500 mA VIN = 6.0 V → 14.0 V, IOUT = 250 mA Min 4.850 Typ 5.0 Max 5.150 60 120 Unit V mV mV mA
REGLOA VIN = 6.0 V, IOUT = 0 mA → 1 000 mA
VIN = 6.0 V, The output current value 1 200 when VOUT decreases by 5% from its value at IOUT = 500 mA. VIN = 6.0 V, IOUT = 0 mA −5 49.9 0.50
Bias current under no load Bias current fluctuation to input Bias current fluctuation to load Standby consumption current Bias current before starting regulation Control terminal current Ripple rejection ratio 1 Minimum input/ output voltage difference 1 Minimum input/ output voltage difference 2 Control terminal threshold high voltage Control terminal threshold low voltage • Design reference data
IBIAS
1.1 0.30 1.45 0.70
3.0 5 50 3.0 5 30 0.60 1.0 1.80
mA mA mA µA mA µA dB V V V V
∆IBIAS(IN) VIN = 6.0 V → 14.0 V, IOUT = 250 mA ∆IBIAS(LOA) VIN = 6.0 V, IOUT = 0 mA → 1 000 mA ISTB IRUSH ICONT RR1 VIN = 14.0 V, VCONT = 0 V VIN = 4.750 V, IOUT = 0 A VIN = 6.0 V, IOUT = 500 mA VCONT = 1.8 V VIN = 7.0 V ± 1 V[p-p] f = 120 Hz, IOUT = 100 mA
VDIF(min)1 VIN = 5.1 V, IOUT = 500 mA VDIF(min)2 VIN = 5.2 V, IOUT = 1 000 mA VCONTH VCONTL VIN = 6.0 V VIN = 6.0 V
Note) The following values are typical and not guaranteed values.
Parameter Ripple rejection ratio 2 Output noise voltage Output voltage temperature coefficient Output short-circuit current Overheat protection operating temperature
Symbol RR2 VNO dVOUT dTa IOSHORT TjTH
Conditions VIN = 7.0 V ± 1 V[p-p], COUT = 33 +0.1 µF f = 500 kHz, IOUT = 100 mA 10 Hz ≤ f ≤ 100 kHz, IOUT = 100 mA CNR = 1 µF, VIN = 6.0 V VIN = 6.0 V, IOUT = 5 mA −30°C ≤ Ta ≤ +125°C VIN = 14.0 V, VOUT = GND VIN = 6.0 V, IOUT = 5 mA
Min
Typ 30 40 ±40 2 000 150
Max
Unit dB µV[rms] ppm/°C mA °C
22
SFF00010CEB
AN80PxxRSP Series
I Electrical Characteristics at Ta = 25°C (continued)
• AN80P51RSP (5.1 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 100 µF, CNR = Open, COUT = 0.1 µF Parameter Output voltage Line regulation Load regulation Peak output current Symbol VOUT REGIN IPEAK Conditions VIN = 6.1 V, IOUT = 500 mA VIN = 6.1 V → 14.0 V, IOUT = 250 mA Min 4.947 Typ 5.1 Max 5.253 51 102 Unit V mV mV mA
REGLOA VIN = 6.1 V, IOUT = 0 mA → 1 000 mA
VIN = 6.1 V, The output current value 1 200 when VOUT decreases by 5% from its value at IOUT = 500 mA. VIN = 6.1 V, IOUT = 0 mA −5 49.8 0.50
Bias current under no load Bias current fluctuation to input Bias current fluctuation to load Standby consumption current Bias current before starting regulation Control terminal current Ripple rejection ratio 1 Minimum input/ output voltage difference 1 Minimum input/ output voltage difference 2 Control terminal threshold high voltage Control terminal threshold low voltage • Design reference data
IBIAS
1.1 0.30 1.45 0.70
3.0 5 50 3.0 5 30 0.60 1.0 1.80
mA mA mA µA mA µA dB V V V V
∆IBIAS(IN) VIN = 6.1 V → 14.0 V, IOUT = 250 mA ∆IBIAS(LOA) VIN = 6.1 V, IOUT = 0 mA → 1 000 mA ISTB IRUSH ICONT RR1 VIN = 14.0 V, VCONT = 0 V VIN = 4.845 V, IOUT = 0 A VIN = 6.1 V, IOUT = 500 mA VCONT = 1.8 V VIN = 7.1 V ± 1 V[p-p] f = 120 Hz, IOUT = 100 mA
VDIF(min)1 VIN = 5.2 V, IOUT = 500 mA VDIF(min)2 VIN = 5.3 V, IOUT = 1 000 mA VCONTH VCONTL VIN = 6.1 V VIN = 6.1 V
Note) The following values are typical and not guaranteed values.
Parameter Ripple rejection ratio 2 Output noise voltage Output voltage temperature coefficient Output short-circuit current Overheat protection operating temperature
Symbol RR2 VNO dVOUT dTa IOSHORT TjTH
Conditions VIN = 7.1 V ± 1 V[p-p], COUT = 33 +0.1 µF f = 500 kHz, IOUT = 100 mA 10 Hz ≤ f ≤ 100 kHz, IOUT = 100 mA CNR = 1 µF, VIN = 6.1 V VIN = 6.1 V, IOUT = 5 mA −30°C ≤ Ta ≤ +125°C VIN = 14.0 V, VOUT = GND VIN = 6.1 V, IOUT = 5 mA
Min
Typ 30 40 ±40 2 000 150
Max
Unit dB µV[rms] ppm/°C mA °C
SFF00010CEB
23
AN80PxxRSP Series
I Electrical Characteristics at Ta = 25°C (continued)
• AN80P52RSP (5.2 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 100 µF, CNR = Open, COUT = 0.1 µF Parameter Output voltage Line regulation Load regulation Peak output current Symbol VOUT REGIN IPEAK Conditions VIN = 6.2 V, IOUT = 500 mA VIN = 6.2 V → 14.0 V, IOUT = 250 mA Min 5.044 Typ 5.2 Max 5.356 52 104 Unit V mV mV mA
REGLOA VIN = 6.2 V, IOUT = 0 mA → 1 000 mA
VIN = 6.2 V, The output current value 1 200 when VOUT decreases by 5% from its value at IOUT = 500 mA. VIN = 6.2 V, IOUT = 0 mA −5 49.6 0.50
Bias current under no load Bias current fluctuation to input Bias current fluctuation to load Standby consumption current Bias current before starting regulation Control terminal current Ripple rejection ratio 1 Minimum input/ output voltage difference 1 Minimum input/ output voltage difference 2 Control terminal threshold high voltage Control terminal threshold low voltage • Design reference data
IBIAS
1.1 0.30 1.45 0.70
3.0 5 50 3.0 5 30 0.60 1.0 1.80
mA mA mA µA mA µA dB V V V V
∆IBIAS(IN) VIN = 6.2 V → 14.0 V, IOUT = 250 mA ∆IBIAS(LOA) VIN = 6.2 V, IOUT = 0 mA → 1 000 mA ISTB IRUSH ICONT RR1 VIN = 14.0 V, VCONT = 0 V VIN = 4.940 V, IOUT = 0 A VIN = 6.2 V, IOUT = 500 mA VCONT = 1.8 V VIN = 7.2 V ± 1 V[p-p] f = 120 Hz, IOUT = 100 mA
VDIF(min)1 VIN = 5.3 V, IOUT = 500 mA VDIF(min)2 VIN = 5.4 V, IOUT = 1 000 mA VCONTH VCONTL VIN = 6.2 V VIN = 6.2 V
Note) The following values are typical and not guaranteed values.
Parameter Ripple rejection ratio 2 Output noise voltage Output voltage temperature coefficient Output short-circuit current Overheat protection operating temperature
Symbol RR2 VNO dVOUT dTa IOSHORT TjTH
Conditions VIN = 7.2 V ± 1 V[p-p], COUT = 33 +0.1 µF f = 500 kHz, IOUT = 100 mA 10 Hz ≤ f ≤ 100 kHz, IOUT = 100 mA CNR = 1 µF, VIN = 6.2 V VIN = 6.2 V, IOUT = 5 mA −30°C ≤ Ta ≤ +125°C VIN = 14.0 V, VOUT = GND VIN = 6.2 V, IOUT = 5 mA
Min
Typ 30 40 ±40 2 000 150
Max
Unit dB µV[rms] ppm/°C mA °C
24
SFF00010CEB
AN80PxxRSP Series
I Electrical Characteristics at Ta = 25°C (continued)
• AN80P53RSP (5.3 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 100 µF, CNR = Open, COUT = 0.1 µF Parameter Output voltage Line regulation Load regulation Peak output current Symbol VOUT REGIN IPEAK Conditions VIN = 6.3 V, IOUT = 500 mA VIN = 6.3 V → 14.0 V, IOUT = 250 mA Min 5.141 Typ 5.3 Max 5.459 53 106 Unit V mV mV mA
REGLOA VIN = 6.3 V, IOUT = 0 mA → 1 000 mA
VIN = 6.3 V, The output current value 1 200 when VOUT decreases by 5% from its value at IOUT = 500 mA. VIN = 6.3 V, IOUT = 0 mA −5 49.5 0.50
Bias current under no load Bias current fluctuation to input Bias current fluctuation to load Standby consumption current Bias current before starting regulation Control terminal current Ripple rejection ratio 1 Minimum input/ output voltage difference 1 Minimum input/ output voltage difference 2 Control terminal threshold high voltage Control terminal threshold low voltage • Design reference data
IBIAS
1.1 0.30 1.45 0.70
3.0 5 50 3.0 5 30 0.60 1.0 1.80
mA mA mA µA mA µA dB V V V V
∆IBIAS(IN) VIN = 6.3 V → 14.0 V, IOUT = 250 mA ∆IBIAS(LOA) VIN = 6.3 V, IOUT = 0 mA → 1 000 mA ISTB IRUSH ICONT RR1 VIN = 14.0 V, VCONT = 0 V VIN = 5.035 V, IOUT = 0 A VIN = 6.3 V, IOUT = 500 mA VCONT = 1.8 V VIN = 7.3 V ± 1 V[p-p] f = 120 Hz, IOUT = 100 mA
VDIF(min)1 VIN = 5.4 V, IOUT = 500 mA VDIF(min)2 VIN = 5.5 V, IOUT = 1 000 mA VCONTH VCONTL VIN = 6.3 V VIN = 6.3 V
Note) The following values are typical and not guaranteed values.
Parameter Ripple rejection ratio 2 Output noise voltage Output voltage temperature coefficient Output short-circuit current Overheat protection operating temperature
Symbol RR2 VNO dVOUT dTa IOSHORT TjTH
Conditions VIN = 7.3 V ± 1 V[p-p], COUT = 33 +0.1 µF f = 500 kHz, IOUT = 100 mA 10 Hz ≤ f ≤ 100 kHz, IOUT = 100 mA CNR = 1 µF, VIN = 6.3 V VIN = 6.3 V, IOUT = 5 mA −30°C ≤ Ta ≤ +125°C VIN = 14.0 V, VOUT = GND VIN = 6.3 V, IOUT = 5 mA
Min
Typ 30 40 ±40 2 000 150
Max
Unit dB µV[rms] ppm/°C mA °C
SFF00010CEB
25
AN80PxxRSP Series
I Application Notes
1. External compensation capacitor Connect the input pin and ground pin with a 100 µF capacitor and the output pin and ground pin with a 0.1 µF capacitor in order to keep the stability of the IC in operation. Make sure that the 10 µF capacitor is as close to the input pin and ground pin as possible while the 33 µF capacitor is as close to the output pin and ground pin as possible. As the stability is affected by the parasitic capacitance and impedance of the PCB pattern, pay utmost attention to the PCB layout. Select each capacitor in consideration of the ESR (equivalent series resistance) of the capacitor for the AN80PxxRSP Series, conduct a ful evaluation under the right operating conditions. The ESR of an aluminum or tantalum electrolytic capacitor may increase at low temperatures. Therefore, it is recommended to connect a 0.1 µF to 0.47 µF capacitor with low internal impedance, such as a multi-layer ceramic capacitor, in parallel to each capacitor. Output current Output capacitor ESR (equivalent series resistance) 2. PD Ta curves of SP-5SU PD T a
1.200
1.051 1.000
Mounted on standard board (glass epoxy: 50 mm × 50 mm × t0.8 mm) Rth(j-a) = 118.9°C/W
Power dissipation PD (W)
0.800
0.600 0.491 0.400 Independent IC without a heat sink Rth(j-a) = 254.4°C/W 0.200
0.000 0 25 50 75 85 100 125 150
20
Ambient temperature Ta (°C)
15
ESR (Ω) COUT
4Ω
10
5
Possible operating range
0 0 200 400 600 800 1 000
Output current IOUT (mA)
3. Main characteristics •AN80PxxRSP series VOUT T
VIN = Vtyp + 1 V IO = 5 mA
•AN80P18RSP
2 1.8 1.6 1.4
VO IO (25°C)
+1
VIN = 2.5 V 2.8 V 3.3 V 3.6 V
0
∆VOUT (%)
1.2
−1
VO (V)
−25
1 0.8
−2
0.6 0.4 0.2 0 0 0.5 1 1.5 2 2.5
−3
0
25
50
75
100
125
150
T (°C)
IO (A)
SFF00010CEB
26
AN80PxxRSP Series
I New Package Dimensions (Unit: mm)
• SP-5SUA (Lead-free package) 6.50±0.10 5.40±0.10 (4.35) (3.00)
(1.80) (2.50)
(0.50)
5.50±0.10
(5.30) 9.80±0.20
2.50±0.20
(0.50)
3 1 2 1.27
1.00±0.20 5 0.50+0.10 -0.05
4 (0.75) 5.08±0.10
0.13 M
0.10±0.10 0.50+0.10 -0.05
2.30±0.10
1.00±0.20
SFF00010CEB
27
Request for your special attention and precautions in using the technical information and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. (2) The technical information described in this material is limited to showing representative characteristics and applied circuit examples of the products. It does not constitute the warranting of industrial property, the granting of relative rights, or the granting of any license. (3) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: • Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. • Any applications other than the standard applications intended. (4) The products and product specifications described in this material are subject to change without notice for reasons of modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, redundant design is recommended, so that such equipment may not violate relevant laws or regulations because of the function of our products. (6) When using products for which dry packing is required, observe the conditions (including shelf life and after-unpacking standby time) agreed upon when specification sheets are individually exchanged. (7) No part of this material may be reprinted or reproduced by any means without written permission from our company.
Please read the following notes before using the datasheets
A. These materials are intended as a reference to assist customers with the selection of Panasonic semiconductor products best suited to their applications. Due to modification or other reasons, any information contained in this material, such as available product types, technical data, and so on, is subject to change without notice. Customers are advised to contact our semiconductor sales office and obtain the latest information before starting precise technical research and/or purchasing activities. B. Panasonic is endeavoring to continually improve the quality and reliability of these materials but there is always the possibility that further rectifications will be required in the future. Therefore, Panasonic will not assume any liability for any damages arising from any errors etc. that may appear in this material. C. These materials are solely intended for a customer's individual use. Therefore, without the prior written approval of Panasonic, any other use such as reproducing, selling, or distributing this material to a third party, via the Internet or in any other way, is prohibited.
2001 MAR
工商网监
湘ICP备2023018690号
