MN101C77D

MN101C77A, MN101C77C, MN101C77D, MN101C77F Type Internal ROM type ROM (byte) RAM (byte) Package (Lead-free) 32K 1.5K LQFP064-P-1414 48K 3K LQFP064-P-1414, TQFP064-P-1010C MN101C77A MN101C77C MN101C77D 64K LQFP064-P-1414 MN101C77F 96K MN101CF77G FLASH 128K 6K LQFP064-P-1414 LQFP064-P-1414, (Under development) TQFP064-P-1010C Mask ROM Minimum Instruction Execution Time [Standard] 0.1 µs (at 2.5 V to 3.6 V, 20 MHz)* 0.2 µs (at 2.1 V to 3.6 V, 10 MHz)* 0.5 µs (at 1.8 V to 3.6 V, 4 MHz)* 62.5 µs (at 1.8 V to 3.6 V, 32 kHz)* [Double speed] 0.119 µs (at 2.5 V to 3.6 V, 8.39 MHz)* * The operation guarantee range for flash memory built-in type is 2.7 V to 3.6 V.  Interrupts RESET, Watchdog, External 0 to 4, Timer 0, Timer 1, Timer 4 to 6, Timer 7 (2 systems), Time base, Serial 0 reception, Serial 0 transmission, Serial 1 reception, Serial 1 transmission, Serial 3, Serial 4, Automatic transfer finish, A/D conversion finish, Key interrupts (8 lines) Timer counter 0 : 8-bit × 1 (square-wave/8-bit PWM output, event count, generation of remote control carrier, pulse width measurement) Clock source................ 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source ........... coincidence with compare register 0 Timer counter 1 : 8-bit × 1 (square-wave output, event count, synchronous output event) Clock source................ 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source ........... coincidence with compare register 1 Timer counter 0, 1 can be cascade-connected.  Timer Counter Timer counter 4 : 8-bit × 1 (square-wave/8-bit PWM output, event count, pulse width measurement, serial 1 baud rate timer) Clock source................ 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; 1/1 of external clock input frequency Interrupt source ........... coincidence with compare register 4 Timer counter 5 : 8-bit × 1 (square-wave/8-bit PWM output, event count, pulse width measurement, serial 0 baud rate timer) Clock source................ 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; 1/1 of external clock input frequency Interrupt source ........... coincidence with compare register 5 Timer counter 6 : 8-bit freerun timer Clock source................ 1/1 of system clock frequency; 1/1, 1/4096, 1/8192 of OSC oscillation clock frequency; 1/1, 1/4096, 1/8192 of XI oscillation clock frequency Interrupt source ........... coincidence with compare register 6 Timer counter 7 : 16-bit × 1 (square-wave/16-bit PWM output, cycle / duty continuous variable, event count, synchronous output evevt, pulse width measurement, input capture) Clock source................ 1/1, 1/2, 1/4, 1/16 of system clock frequency; 1/1, 1/2, 1/4, 1/16 of OSC oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency Interrupt source ........... coincidence with compare register 7 (2 lines) MAD00038JEM MN101C77A, MN101C77C, MN101C77D, MN101C77F Time base timer (one-minute count setting) Clock source................ 1/1 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency Interrupt source ........... 1/128, 1/256, 1/512, 1/1024, 1/8192, 1/32768 of clock source frequency Watchdog timer Interrupt source ........... 1/65536, 1/262144, 1/1048576 of system clock frequency  Serial interface Serial 0 : synchronous type / UART (full-duplex) × 1 Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 5; 1/2, 1/4, 1/16, 1/64 of OSC oscillation clock frequency Serial 1 : synchronous type / UART (full-duplex) × 1 Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 4; 1/2, 1/4, 1/16, 1/64 of OSC oscillation clock frequency Serial 3 : synchronous type/single-master I²C × 1 Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 3; 1/2, 1/4, 1/16, 1/32 of OSC oscillation clock frequency Serial 4 : I²C slave × 1 (Applicable for I²C high-speed transfer mode, 7 bit/10bit address setting, general call)  DMA controller Max. Transfer cycles : 255 Starting factor : external request, various types of interrupt, software Transfer mode : 1-byte transfer, word transfer, burst transfer  I/O Pins I/O 53 Common use , Specified pull-up resistor available, Input/output selectable (bit unit)  A/D converter  D/A converter  Special Ports 10-bit × 7-ch. (with S/H) 8-bit × 2-ch. (Serves as AD pin, as well) Buzzer output, remote control carrier signal output, high-current drive port Correcting address designation : up to 3 addresses possible  ROM Correction  Electrical Charactreistics (Supply current) Parameter Symbol IDD1 Operating supply current IDD2 IDD3 Supply current at HALT Supply current at STOP IDD4 IDD5 IDD6 IDD7 Condition fosc = 20 MHz , VDD = 3.3 V, (fs = fosc/2) fosc = 8.39 MHz , VDD = 3.3 V, (fs = fosc/2) fx = 32.768 kHz , VDD = 3.3 V, (fs = fx/2) fx = 32.768 kHz , VDD = 3.3 V, Ta = 25°C fx = 32.768 kHz , VDD = 3.3 V VDD = 3.3 V, Ta = 25°C VDD = 3.3 V, Ta = 85°C 5 Limit min typ 6 3 max 12 6 40 10 40 2 30 Unit mA mA µA µA µA µA µA (Ta = –40°C to +85°C , VDD = 1.8 V to 3.6 V , VSS = 0 V)  Development tools In-circuit Emulator PX-ICE101C/D+PX-PRB101C77-TQFP064-P-1010C PX-ICE101C/D+PX-PRB101C77-LQFP064-P-1414 MAD00038JEM  Pin Assignment P73, SB00B, TXD0B P70, SB01B, TXD1B P71, SBI1B, RXD1B P67, SD07, KEY7 P66, SD06, KEY6 P65, SD05, KEY5 P64, SD04, KEY4 P63, SD03, KEY3 P62, SD02, KEY2 P61, SD01, KEY1 P60, SD00, KEY0 P51, SB03, SDA3 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 10 12 13 14 15 16 11 1 2 3 4 5 6 7 8 9 P52, SBT3, SCL3 34 P53, SDA4B 35 P72, SBT1B P54, SCL4B 36 48 47 46 45 44 43 42 41 40 39 38 P74, SBI0B, RXD0B P75, SBT0B P76, TCI01 P77, TCI05 P87, LED7 P86, LED6 P85, LED5 P84, LED4 P83, LED3 P82, LED2 P81, LED1 P80, LED0 AVSS PA0, AN0, DA0 PA1, AN1, DA1 PA2, AN2 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 37 SBI3, P50 IRQ4, P24 IRQ3, P23 IRQ2, P22 ACZ, IRQ1, P21 IRQ0, P20 TCI07, P14 TCI04B, P13 TC04A, P12 TCI00B, P11 RMOUT, TC00A, P10 BUZZER, P06 SBT0A, P05 RXD0A, SBI0A, P04 TXD0A, SB00A, P03 SCL4A, SBT1A, P02 MN101C77A MN101C77C MN101C77D MN101C77F XI OSC2 OSC1 VDD VSS XO N.C. (VPP) MMOD TXD1A, SB01A, P00 LQFP064-P-1414 TQFP064-P-1010C [MN101C77C] Note) N.C. serves as the VPP pin in the MN101CF77G, and cannot be used as a user pin. SDA4A, RXD1A, SBI1A, P01 NRST, P27 AN3, PA3 AN4, PA4 AN5, PA5 AN6, PA6 AVDD MAD00038JEM Request for your special attention and precautions in using the technical information and semiconductors described in this book (1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) The technical information described in this book is intended only to show the main characteristics and application circuit examples of the products, and no license is granted under any intellectual property right or other right owned by our company or any other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: – Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. – Any applications other than the standard applications intended. (4) The products and product specifications described in this book are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita Electric Industrial Co., Ltd. Industrial Co., Ltd.