MN101CA2

MN101CA2 Series Type Internal ROM type ROM (byte) RAM (byte) Package (Lead-free) Minimum Instruction Execution Time MN101CA27 Mask ROM 16K 0.5K LQFP064-P-1414 0.25 µs (at 2.7 V to 3.6 V, 8 MHz) 0.50 µs (at 1.8 V to 3.6 V, 4 MHz) 62.5 µs (at 1.8 V to 3.6 V, 32 kHz) MN101CFA2D FLASH 64K 2K  Interrupts RESET. Watchdog. External 2. External 6. Timer 0. Timer 1. Timer 6. Time base  Timer Counter 8-bit timer × 2 Timer 0 ..................Square-wave/8-bit PWM output. Simple pulse width measurement Timer 1 ..................Square-wave output Timer 0, 1 can be cascade-connected Time base timer: One-minute count setting Watchdog timer × 1 Remote control carrier output  I/O Pins I/O Input 16 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit) 9 : Common use. Specified pull-up resistor available  Display control function LCD: 32 segments × 4 commons (1/3 or 1/4 duty)  Special Ports Buzzer output. Remote control carrier output. High-current drive port  Electrical Charactreistics (Supply current) Parameter Operating supply current Supply current at HALT Supply current at STOP Symbol IDD1 IDD2 IDD3 IDD4 IDD5 fx = 32 kHz. VDD = 3 V fx = 32 kHz. VDD = 3 V. Ta = 25 °C fx = 32 kHz. VDD = 3 V. Ta = 70 °C VDD = 3 V. Ta = 25 °C VDD = 3 V. Ta = 70 °C Condition fosc = 8 MHz. VDD = 3 V min Limit typ 1.0 4.8 2.7 max 1.8 17 5 13 2 8 Unit mA µA µA µA µA µA Note) Limit: Mask ROM version MAD00070DEM MN101CA27, MN101CFA2D  Pin Assignment LQFP064-P-1414 SEG22 SEG23 P37, SEG24 P36, SEG25 P35, SEG26 P34, SEG27 P33, SEG28 P32, SEG29 P31, SEG30 P30, SEG31 P21, RMOUT P20, IRQ2 P07, KEY7 P06, KEY6 P05, KEY5 P04, KEY4 SEG21 SEG20 SEG19 SEG18 SEG17 SEG16 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 P17 P16 P15 P14 P13 TM1O, P12 TM0O, P11 BUZZER, P10 KEY3, P03 KEY2, P02 KEY1, P01 KEY0, P00 NRST, P27 VSS XI XO MAD00070DEM SEG5 SEG4 SEG3 SEG2 SEG1 SEG0 COM3 COM2 COM1 COM0 VLC3, MMOD VLC2 VLC1 VDD OSC1 OSC2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Request for your special attention and precautions in using the technical information and semiconductors described in this book (1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) The technical information described in this book is intended only to show the main characteristics and application circuit examples of the products. No license is granted in and to any intellectual property right or other right owned by Panasonic Corporation or any other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: – Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. – Any applications other than the standard applications intended. (4) The products and product specifications described in this book are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company. 20080805