MN101EF11G

MN101E11G Type Internal ROM type ROM (byte) RAM (byte) Package (Lead-free) Minimum Instruction Execution Time QFP084-P-1818E 100 ns (at 3.135 V to 3.465 V, , normal-mode) MN101E11G Mask ROM 128K 4K QFP084-P-1818E (ES (Engineering Sample) available) 100 ns MN101EF11G FLASH  Interrupts External (5 lines) Internal (13 lines) : Timer × 4, A/D × 1, RESET × 1, OSD × 1, Serial × 2, I²C × 1, Caption × 1, Remote control × 1, HSYNC× 1, VSYNC× 1 8-bit timer × 4 Watchdog timer : Time-out period is selectable. I²C × 1 : for multimaster mode, bus line (output) has 2 systems Sync serial / UART × 1  Timer Counter  Serial interface  Caption / Teletext Decoder ・Built-in sync separator × 1  I/O Pins I/O 30 Common use  A/D converter  PWM 10-bit × 8-ch. (with S/H) 8-bit × 4-ch. , 14-bit × 1-ch. Remote control reception 1-layer display (graphics, characters, splits) Remote control input discriminant circuit built-in, build-in NTSC video signal processing circuit, built-in 3-line comb filter, PinP available In-circuit Emulator PX-PAC101E02-4W9J  Special Ports  CRTC  Notes  Development tools MAD00044DEM MN101E11G  Pin Assignment VDD(VPP) *2 P07, ADIN7, VDAF P06, ADIN6, HDAF P05, ADIN5 DVDD DVSS P04, ADIN4 P03, ADIN3 P02, ADIN2 P01, ADIN1 P00, ADIN0 MMOD OSC2 OSC1 PDO VCOI AVDD AVSS BOUT SIREF SCOMP 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 Note) *1: 5 V dielectric N-ch. open drain output pin *2: Mask ROM = VDD, Flash memory built-in type = VPP MAD00044DEM P33, IRQ3 P34, IRQ4 VSYNC P36, PWM4 PIPYS PIPYIN PIPVIN PIPUIN AVDD AVSS VREFH VREFM MCOMPIN VREFL MSCIN CREFH MVIN CLH MUIN CLL CREFL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 P10, RMIN, IRQ0 P11, SDA0 *1 P12, SCL0 *1 P13, PWM *1 P14, VOUT0 P15, SBT0 P16, SBD0 P17, SBO0 P20, SDA1 *1 P21, SCL1 *1 P22, PWM0 *1 P23, PWM1 P24, PWM2 DVDD DVSS P25, SYSCLK P26, TM0IO *1 P27, TM1IO *1 P30, NRST P31, IRQ1 P32, IRQ2 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 MN101E11G GOUT ROUT VIREF VCOMP VMOUT AVDD FBPIN AVSS EW VOUT AVDD FSCOUT FSCIN FPCO AVSS FVCOI HOUT HDOWN EHTIN BEAMIN ABLIN QFP084-P-1818E Request for your special attention and precautions in using the technical information and semiconductors described in this book (1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) The technical information described in this book is intended only to show the main characteristics and application circuit examples of the products, and no license is granted under any intellectual property right or other right owned by our company or any other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: – Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. – Any applications other than the standard applications intended. (4) The products and product specifications described in this book are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita Electric Industrial Co., Ltd. Industrial Co., Ltd.