FSTMMBL

specifications ® ST* fiber optic connectors shall be compliant with TIA FOCIS-2. ST* connectors shall contain a factory terminated pre-polished multimode fiber, requiring no field polishing and no adhesive. The fiber shall terminate in a 2.5mm ferrule and have a typical insertion loss of 0.3dB (62.5/125µm) or 0.35dB (50/125µm) per connector. NETWORK CONNECTIVITY GROUP SPEC SHEET ST* OPTI-CRIMP ® Fiber Optic Connector — Pre-polished Crimp technical information ST* OPTI-CRIMP Multimode Connectors Fiber compatibility: 62.5/125µm and 50/125µm multimode versions available Fiber cable type: Tight-buffered cable only (3.0mm jacketed or 900µm) Ferrule type: Zirconia ceramic with a pre-polished fiber stub Insertion loss: 0.3dB typical (62.5/125µm), 0.35dB typical (50/125µm) Return loss: Greater than 20dB 62.5/125µm black boot: 62.5/125µm red boot: 50/125µm black boot: 50/125µm red boot: FSTMMBL FSTMMRD FSTMM50BL FSTMM50RD ST* Adapter Modules with Phosphor Bronze Split Sleeve key features and benefits Pre-polished fiber stub Eliminates polishing steps, speeding installation VFL verification during crimp process Provides installer with a visual signal when optimal continuity is made and the crimp step can be performed Mechanical crimp cable retention Consistently provides higher than industry standard cable retention; requires no adhesive, speeding installation Proven 2.5mm ceramic ferrules Uses standard termination tools and procedures; provides strength and reliability Robust design Protects fibers from mechanical and environmental stress FOCIS-2 compliant Ensures intermatability with all FOCIS-2 compliant components Exceeds TIA/EIA-568-B.3 Network reliability assured as defined by TIA Simplex: CMST** ST* Adapter Modules with Zirconia Ceramic Split Sleeve Simplex: CMSTZ** Multimode Patch Cords and Pigtails Duplex ST* to ST*: Simplex ST* to ST*: Simplex 900µm buffered ST* pigtail: Duplex ST* to SC: Duplex FJ ® plug to ST*: F^D2-2M‡ F^S2-2M‡ F^B2-NM‡ F^D2-3M‡ F^D6P-2M‡ ^Available in 62.5/125µm (6) and 50/125µm (5). ‡Patch cords are available in 1, 2, 3, 5 and 10 meter lengths, and pigtails are available in 1, 2 and 3 meter lengths. OPTI-CRIMP Termination Tooling Termination kit: applications The ST* OPTI-CRIMP Fiber Optic Connector improves an industry standard design. Elimination of end face polishing and adhesive provides for easier, faster installation, especially in remote areas and confined spaces. This reduces installation time over standard field polish ST* connectors by 50%. ST* Fiber Optic Connectors are widely used in fiber optic backbone and horizontal applications for high-speed data transmissions. installer tips Terminate on tight-buffered cable only. Always use FVFL Visual Fault Locator during termination. *ST is a registered trademark of Lucent Technologies. V i s i t o u r w e b s i t e a t : w w w. p a n d u i t . c o m / n c g FJMVKIT To upgrade from FJKITG, purchase FJQCVR fiber cleaver tool and FVFLKIT visual fault locator kit. To upgrade from FJMKIT, purchase FVFLKIT visual fault locator kit. **Substitute for Colors: EI = BU = BL = IW = AW = Electric Ivory Blue Black Off White Arctic White ST* OPTI-CRIMP ® Fiber Optic Connector — Pre-polished Crimp Standards Compliant Connector Performance TIA 455 Description Test Procedure and TIA/EIA-568-B.3 Required Performance 1 Flex Apply 1.1lb. (jacketed) or .5lb (buffered) load thru 180° for 100 cycles; 0.75dB maximum insertion loss < 0.1dB additional loss 2 Impact 8 drops from 1.8m 0.75dB maximum insertion loss < 0.1dB additional loss 4 High Temperature 60°C for 4 days; 0.75dB maximum insertion loss < 0.1dB additional loss 5 Humidity 40°at 95% RH for 4 days;