PAN -SHRINK ™ Catalog
SA# 101N48F-AIS
DRY -S HRINK ™ , DAMP-SHRINK ™ and WET-SHRINK ™
Heat Shrink and Abrasion Protection Products
Contents
Heat Shrink Products
Type
Polyolefin, General Purpose Tubing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HSTT . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Polyolefin, General Purpose Tubing For Displays . . . . . . . . . . . . . . . . . . . . . . . HSTTD . . . . . . . . . . . . . . . . . . . . . . . . . . .
Polyolefin, VW-1 Rated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HSTTV . . . . . . . . . . . . . . . . . . . . . . . . . . .
Polyolefin, Semi-Rigid Tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HSTTR . . . . . . . . . . . . . . . . . . . . . . . . . . .
PVC Heat Shrink Tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HSTTP . . . . . . . . . . . . . . . . . . . . . . . . . . .
Neoprene Heat Shrink Tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HSTTN . . . . . . . . . . . . . . . . . . . . . . . . . . .
TEFLON Type TFE Heat Shrink Tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HSTTT . . . . . . . . . . . . . . . . . . . . . . . . . . .
TEFLON Type FEP Heat Shrink Tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HSTTF . . . . . . . . . . . . . . . . . . . . . . . . . . .
KYNAR Heat Shrink Tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HSTTK . . . . . . . . . . . . . . . . . . . . . . . . . . .
Polyolefin, Dual Wall, 2:1 Shrink Ratio with Adhesive . . . . . . . . . . . . . . . . . . . . HSTTVA . . . . . . . . . . . . . . . . . . . . . . . . . .
Polyolefin, Dual Wall, 3:1 Shrink Ratio with Adhesive . . . . . . . . . . . . . . . . . . . . HSTTA . . . . . . . . . . . . . . . . . . . . . . . . . . .
Polyolefin, Dual Wall, Semi-Rigid with Adhesive . . . . . . . . . . . . . . . . . . . . . . . . HSTTRA . . . . . . . . . . . . . . . . . . . . . . . . .
Thick Wall Heat Shrink Tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HST . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thick Wall Heat Shrink End Caps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HSEC . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Heat Shrink Kits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Heat Shrink Tools, Accessor ies and Replacement Parts. . . . . . . . . . . . . . . . . . HSG . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page
4-9
10
11-13
14
15
16
17
18
19
20
21
22
23
24
25-26
27
Technical Information and Size Selection Guides
Heat Shrink Process Defined . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Heat Shrink Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ingress Protection Technical Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended Tubing Size for Common Wire Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Size Selection for Heat Shrink Tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thick Wall Heat Shrink and Power Connector Selection Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Infor mation on Heat Shrink Tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications/Test Methods for Heat Shrink Tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Panduit Power Connectors used with Thick Wall Heat Shrink. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28
28
29
30
31
32
33-34
35-36
37
Non-Heat Shrinkable Tubing
PVC Tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TV105 . . . . . . . . . . . . . . . . . . . . . . . . . . . 38-39
Abrasion Protection Products
Spiral Wrapping
Spiral Wrapping Features, Benefits and Suggested Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Spiral Wrapping Par t Number System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Spiral Wrapping Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42-43
Grommet Edging
Grommet Edging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GEE,GE,GES,GEM . . . . . . . . . . . . . . . . . 44-46
Corrugated Loom Tubing
Corrugated Loom Tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CLT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47-48
Braided Expandable Sleeving
Braided Expandable Sleeving— Type PET . . . . . . . . . . . . . . . . . . . . . . . . . . . . SE*P . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Braided Expandable Sleeving, Flame Retardant— Type PET . . . . . . . . . . . . . . SE**PFR . . . . . . . . . . . . . . . . . . . . . . . . .
Abrasion Protection Products Flammability Tests and Classifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Abrasion Protection Products Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
49
50
51-52
53-54
Alphabetical Par t Number Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
KYNAR is a registered trademark of ELF Atochem
TEFLON is a registered trademark of E.I. DuPont Co.
1
PANDUIT DRY -S HRINK ™, DAMP-SHRINK ™ and WET-SHRINK ™
Heat Shrink & Abrasion Protection Products
INSULATE
IDENTIFY
HARNESS
ACCESSORIES
PANDUIT ® DR Y -S HR IN K,
DAMP -SHR IN K and WET-SH RINK
Heat Shrink Tubing provide an
economical and easy way to
insulate, protect, harness and
identify electrical and electronic
components in a wide variety
of applications.
PROTECT
5 Types of Packaging
6" Pieces
4' Lengths
Custom Cut Pieces
(cut to your specifications)
Small Reels
Large Reels
For Technical Assistance, call 866-405-6662
(Outside the U.S., see inside back cover for International Directory)
2
PANDUIT
®
Heat Shrink Tubing — Heat Shrink Tubing Quick Selection Guide
Quick reference for PANDUIT Heat Shrink Tubing for specific location applications
CHARACTERISTICS
ST
H
A
TT
HS A
R
TT
HS
A
TV
ST
H
P
TT
HS
TF
ST
H
4X
TT
ST
H
TT
ST
H
TK
ST
H
N
TT
HS
TR
ST
H
TV
ST
H
TT
HS
U.L. Listed
UL Recognized
X‡
X
CSA Cer tified
X‡
X
VW-1 Rated
X
Very Flexible
X
Flexible
X
Semi-Rigid
Thin Wall
X
X
Thick Wall
Cross-Linked Mater ial
X
X
Colors Available
X
X
High Shr ink Ratio
Flame Retardant
X‡
X
Adhesive Lined (Dual Wall)
Meets Military Specification
X
X
Below Ground Application
High Tem p Applications (>250ºF)
Highly Chemical Resistant
Low Coefficient of Friction
Custom Cut Lengths
X
X
Standard 6" pieces
X
X
Standard 4' lengths
X
X
Small 25' Reels
X
X
Large Reels
X
X
IP Rating
62
62
Found on Page. . .
4-10 11-13
X
X
X
X
X
X
X**
X
X
X
X
X
X
X
X
X
X
X
X
X
X
4:1
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
62
16
62
14
62
19
X
X
—
17
X
X
—
17
X
X
—
18
X
X
X
X
X
X
X
X
X
X
X
X
X
X
2.5:1
X
X
X
3:1
X
X
X
X
X
X
X
X
X
X
X
X
X
66
20
66
22
66
21
68
23
X
X
62
15
X
X
X
X
X*
3:1
X
X
X
X
X
See page 29 for IP Technical information
* Black/Red
**Except red
‡Except Clear
Thin Wall Heat Shrink Part Number System
HSTT
Type
HSTT - Thin Wall
HSTTD - Thin Wall Display
HSTTV - Thin Wall VW-1
HSTTR - Thin Wall Semi-Rigid
HSTTN - Thin Wall Neoprene
HSTTK - Thin Wall KYNAR
HSTTT - Thin Wall TFE TEFLON
HSTTT4X - Thin Wall TEFLON
4:1 Ratio
HSTTF - Thin Wall TEFLON FEP
HSTTP - Thin Wall PVC
HSTTVA - Flexible Adhesive Lined
HSTTRA - Semi-Rigid Adhesive Lined
HSTTA - Thin Wall Adhesive Lined
12 -
Expanded Diameter
05 • 3/64" (1.2mm)
06 • 1/16" (1.6mm)
09 • 3/32" (2.4mm)
12 • 1/8" (3.2mm)
19 • 3/16" (4.8mm)
25 • 1/4" (6.4mm)
38 • 3/8" (9.5mm)
50 • 1/2" (12.7mm)
75 • 3/4" (19.0mm)
100 • 1" (25.4mm)
150 • 1-1/2" (38.1mm)
200 • 2" (50.5mm)
300 • 3" (76.2mm)
400 • 4" (101.6mm)
48
-
Tube Length
48" (1.2M)
NONE • REEL
Q
10
Package Quantity
(If Tube Length Specified)
2 • 2 Pcs.
5 • 5 Pcs.
Q • 25 Pcs.
LQ • 75 Pcs.
CQ • 125 Pcs.
T • 200 Pcs.
TL • 250 Pcs.
Color
NONE • Black
C • Clear
2 • Red
4 • Yellow
5 • Green
6 • Blue
10 • White
45 • Yellow/Green
Reels (If No Tube Length Specified)
Q • 25' (7.6M)
L • 50' (15.2M)
C • 100' (30.5M)
T • 200' (61.0M)
D • 500' (152.4M)
M • 1000' (304.8M)
For Standard Packages containing 6" lengths, refer to individual pages for complete part number offering.
Note: The above information is to be used as a guide. For specific part number offerings review individual pages for verification.
KYNAR is a registered trademark of ELF Atochem
T EF LON is a registed trademark of E.I. DuPont Co.
3
Flexible Polyolefin DRY -S HRINK ™ Heat Shrink Tubing
HSTT Heat Shrink in 4' (1.2M) Pieces and Reels
• General purpose heat shrink tubing for dry locations
• Applications include insulating, protecting,
harnessing and identifying wires
(Except Clear)
(Except Clear)
Ordering Information — HSTT in Bulk Packages — Large Reels and 4' (1.2M) Pcs. (3/64" to 3/4" Expanded I.D.)
Nominal
Diameter
In.
Minimum
Maximum
Expanded
Recovered
I.D. In. (mm) I.D. In. (mm)
Nominal
Recovered
Wall
Thickness
In. (mm)
3/64"
.046" (1.2)
.023" (0.6)
.016" (0.4)
1/16"
.063" (1.6)
.031" (0.8)
.017" (0.4)
3/32"
.093" (2.4)
.046" (1.2)
.020" (0.5)
1/8"
.125" (3.2)
.062" (1.6)
.020" (0.5)
3/16"
.187" (4.8)
.093" (2.4)
.020" (0.5)
1/4"
.250" (6.4)
.125" (3.2)
.025" (0.6)
3/8"
.375" (9.5)
.187" (4.8)
.025" (0.6)
1/2"
.500" (12.7)
.250" (6.4)
.025" (0.6)
3/4"
.750" (19.0)
.375" (9.5)
.030" (0.8)
Length
4' (1.2M)
4' (1.2M)
1 Reel, 100' (30.5M)
1 Reel, 1000' (304.8M)
4' (1.2M)
4' (1.2M)
1 Reel, 100' (30.5M)
1 Reel, 1000' (304.8M)
4' (1.2M)
4' (1.2M)
1 Reel, 100' (30.5M)
1 Reel, 1000' (304.8M)
4' (1.2M)
4' (1.2M)
1 Reel, 100' (30.5M)
1 Reel, 1000' (304.8M)
4' (1.2M)
4' (1.2M)
1 Reel, 100' (30.5M)
1 Reel, 1000' (304.8M)
4' (1.2M)
4' (1.2M)
1 Reel, 100' (30.5M)
1 Reel, 500' (152.4M)
4' (1.2M)
4' (1.2M)
1 Reel 100' (30.5M)
1 Reel, 200' (61.0M)
4' (1.2M)
4' (1.2M)
1 Reel 100' (30.5M)
1 Reel, 200' (61.0M)
4' (1.2M)
4' (1.2M)
1 Reel 100' (30.5M)
1 Reel, 200' (61.0M)
*Order in multiples of Bulk Pkg. Qty. Consult factory for colors not listed.
See page 29 for IP Technical Information
4
Bulk
Pkg.
Qty.*
25 Pcs.
250 Pcs.
1 Reel
1 Reel
25 Pcs.
250 Pcs.
1 Reel
1 Reel
25 Pcs.
250 Pcs.
1 Reel
1 Reel
25 Pcs.
250 Pcs.
1 Reel
1 Reel
25 Pcs.
250 Pcs.
1 Reel
1 Reel
25 Pcs.
250 Pcs.
1 Reel
1 Reel
25 Pcs.
250 Pcs.
1 Reel
1 Reel
25 Pcs.
200 Pcs.
1 Reel
1 Reel
5 Pcs.
125 Pcs.
1 Reel
1 Reel
Bulk
Ctn.
Qty.
Black
—
—
10 Reels
2 Reels
—
—
10 Reels
2 Reels
—
—
10 Reels
2 Reels
—
—
10 Reels
2 Reels
—
—
10 Reels
2 Reels
—
—
10 Reels
2 Reels
—
—
10 Reels
2 Reels
—
—
10 Reels
2 Reels
—
—
10 Reels
2 Reels
HSTT05-48-Q
HSTT05-48-TL
HSTT05-C
HSTT05-M
HSTT06-48-Q
HSTT06-48-TL
HSTT06-C
HSTT06-M
HSTT09-48-Q
HSTT09-48-TL
HSTT09-C
HSTT09-M
HSTT12-48-Q
HSTT12-48-TL
HSTT12-C
HSTT12-M
HSTT19-48-Q
HSTT19-48-TL
HSTT19-C
HSTT19-M
HSTT25-48-Q
HSTT25-48-TL
HSTT25-C
HSTT25-D
HSTT38-48-Q
HSTT38-48-TL
HSTT38-C
HSTT38-T
HSTT50-48-Q
HSTT50-48-T
HSTT50-C
HSTT50-T
HSTT75-48-5
HSTT75-48-CQ
HSTT75-C
HSTT75-T
Flexible Polyolefin DRY-S HRINK ™ Heat Shrink Tubing
Type
Materials
Polyolefin Cross-Linked
HSTT
600V
Flexible
-67° F to 275°F
AMS-DTL-23053/5
(-55°C to 135° C ) Class 1 or Class 2
‡
Shrink Ratio:
2:1
Variety of Colors
Flame Retardant
(Except Clear)
Need help selecting a heat shrink type
or size? Request a Heat Shrink
Selection Guide, SA102N66-AIS.
‡ Maximum UL temperature range is 125°C
Clear
HSTT05-48-QC
HSTT05-48-TLC
HSTT05-CC
HSTT05-MC
HSTT06-48-QC
HSTT06-48-TLC
HSTT06-CC
HSTT06-MC
HSTT09-48-QC
HSTT09-48-TLC
HSTT09-CC
HSTT09-MC
HSTT12-48-QC
HSTT12-48-TLC
HSTT12-CC
HSTT12-MC
HSTT19-48-QC
HSTT19-48-TLC
HSTT19-CC
HSTT19-MC
HSTT25-48-QC
HSTT25-48-TLC
HSTT25-CC
HSTT25-DC
HSTT38-48-QC
HSTT38-48-TLC
HSTT38-CC
HSTT38-TC
HSTT50-48-QC
HSTT50-48-TC
HSTT50-CC
HSTT50-TC
HSTT75-48-5C
HSTT75-48- CQC
HSTT75-CC
HSTT75-TC
Red
HSTT05-48-Q2
—
HSTT05-C2
HSTT05-M2
HSTT06-48-Q2
—
HSTT06-C2
HSTT06-M2
HSTT09-48-Q2
—
HSTT09-C2
HSTT09-M2
HSTT12-48-Q2
—
HSTT12-C2
HSTT12-M2
HSTT19-48-Q2
—
HSTT19-C2
HSTT19-M2
HSTT25-48-Q2
—
HSTT25-C2
HSTT25-D2
HSTT38-48-Q2
—
HSTT38-C2
HSTT38-T2
HSTT50-48-Q2
—
HSTT50-C2
HSTT50-T2
HSTT75-48-5-2
—
HSTT75-C2
HSTT75-T2
Yellow
HSTT05-48-Q4
—
—
HSTT05-M4
HSTT06-48-Q4
—
—
HSTT06-M4
HSTT09-48-Q4
—
—
HSTT09-M4
HSTT12-48-Q4
—
—
HSTT12-M4
HSTT19-48-Q4
—
—
HSTT19-M4
HSTT25-48-Q4
—
—
HSTT25-D4
HSTT38-48-Q4
—
—
HSTT38-T4
HSTT50-48-Q4
—
—
HSTT50-T4
HSTT75-48-5-4
—
—
HSTT75-T4
Green
HSTT05-48-Q5
—
—
HSTT05-M5
HSTT06-48-Q5
—
—
HSTT06-M5
HSTT09-48-Q5
—
—
HSTT09-M5
HSTT12-48-Q5
—
—
HSTT12-M5
HSTT19-48-Q5
—
—
HSTT19-M5
HSTT25-48-Q5
—
—
HSTT25-D5
HSTT38-48-Q5
—
—
HSTT38-T5
HSTT50-48-Q5
—
—
HSTT50-T5
HSTT75-48-5-5
—
—
HSTT75-T5
Blue
HSTT05-48-Q6
—
—
HSTT05-M6
HSTT06-48-Q6
—
—
HSTT06-M6
HSTT09-48-Q6
—
—
HSTT09-M6
HSTT12-48-Q6
—
—
HSTT12-M6
HSTT19-48-Q6
—
—
HSTT19-M6
HSTT25-48-Q6
—
—
HSTT25-D6
HSTT38-48-Q6
—
—
HSTT38-T6
HSTT50-48-Q6
—
—
HSTT50-T6
HSTT75-48-5-6
—
—
HSTT75-T6
White
HSTT05-48-Q10
—
—
HSTT05-M10
HSTT06-48-Q10
—
—
HSTT06-M10
HSTT09-48-Q10
—
—
HSTT09-M10
HSTT12-48-Q10
—
—
HSTT12-M10
HSTT19-48-Q10
—
—
HSTT19-M10
HSTT25-48-Q10
—
—
HSTT25-D10
HSTT38-48-Q10
—
—
HSTT38-T10
HSTT50-48-Q10
—
—
HSTT50-T10
HSTT75-48-5-10
—
—
HSTT75-T10
Yellow/
Green
—
—
—
—
—
—
—
—
—
—
—
—
HSTT12-48-Q45
—
—
HSTT12-M45
HSTT19-48-Q45
—
—
HSTT19-M45
HSTT25-48-Q45
—
—
HSTT25-D45
HSTT38-48-Q45
—
—
HSTT38-T45
HSTT50-48-Q45
—
—
HSTT50-T45
HSTT75-48-545
—
—
HSTT75-T45
5
Flexible Polyolefin DRY -SHRINK ™ Heat Shrink Tubing
HSTT Heat Shrink in 4' (1.2M) Pieces and
Reels continued
• General pur pose heat shrink tubing for dry locations
• Applications include insulating, protecting, harnessing and
identifying wires
(Except Clear)
(Except Clear)
Ordering Information — HSTT in Bulk Packages — Large Reels and 4' (1.2M) Pcs. (1" to 4" Expanded I.D.)
Nominal
Diameter
In.
Minimum
Maximum
Expanded
Recovered
I.D. In. (mm) I.D. In. (mm)
Nominal
Recovered
Wall
Thickness
In. (mm)
1"
1.00" (25.4)
.500" (12.7)
.035" (0.9)
1 1/2"
1.50" (38.1)
.750" (19.0)
.040" (1.0)
2"
2.00" (50.8)
1.00" (25.4)
.045" (1.1)
3"
3.00" (76.2)
1.50" (38.1)
.050" (1.3)
4"
4.00" (101.6)
2.00" (50.8)
.055" (1.4)
Length
4' (1.2M)
4' (1.2M)
1 Reel, 100' (30.5M)
4' (1.2M)
1 Reel, 100' (30.5M)
4' (1.2M)
1 Reel, 50' (15.2M)
4' (1.2M)
1 Reel, 50' (15.2M)
4' (1.2M)
1 Reel, 50' (15.2M)
Bulk
Pkg.
Qty.*
5 Pcs.
75 Pcs.
1 Reel
5 Pcs.
1 Reel
5 Pcs.
1 Reel
2 Pcs.
1 Reel
2 Pcs.
1 Reel
Bulk
Ctn.
Qty.
Black
—
—
2 Reels
—
2 Reels
—
2 Reels
—
—
—
—
HSTT100-48-5
HSTT100-48-LQ
HSTT100-C
HSTT150-48-5
HSTT150-C
HSTT200-48-5
HSTT200-L
HSTT300-48-2
HSTT300-L
HSTT400-48-2
HSTT400-L
* Order in multiples of Bulk Pkg. Qty. Consult factory for colors not listed.
Note: HSTT300-48-2, HSTT300-48-2C, HSTT400-48-2 and HSTT400-48-2C are classified as standard packaged items rather than bulk packaged.
HSTT Heat Shrink on 25' (7.5M) Reels
Ordering Information — HSTT in Standard Packages
Nominal
Diameter
In.
3/64"
1/16"
3/32"
1/8"
3/16"
1/4"
3/8"
1/2"
3/4"
Minimum
Maximum
Expanded
Recovered
I.D. In. (mm) I.D. In. (mm)
Nominal
Recovered
Wall
Thickness
In. (mm)
.046" (1.2)
.063" (1.6)
.093" (2.4)
.125" (3.2)
.187" (4.8)
.250" (6.4)
.375" (9.5)
.500" (12.7)
.750" (19.0)
.016"
.017"
.020"
.020"
.020"
.025"
.025"
.025"
.030"
.023"
.031"
.046"
.062"
.093"
.125"
.187"
.250"
.375"
* Order in multiples of Std. Pkg. Qty.
6
(0.6)
(0.8)
(1.2)
(1.6)
(2.4)
(3.2)
(4.8)
(6.4)
(9.5)
(0.4)
(0.4)
(0.5)
(0.5)
(0.5)
(0.6)
(0.6)
(0.6)
(0.8)
Length
1 Reel, 25' (7.5M)
1 Reel, 25' (7.5M)
1 Reel, 25' (7.5M)
1 Reel, 25' (7.5M)
1 Reel, 25' (7.5M)
1 Reel, 25' (7.5M)
1 Reel, 25' (7.5M)
1 Reel, 25' (7.5M)
1 Reel, 25' (7.5M)
Std.
Pkg.
Qty.*
1
1
1
1
1
1
1
1
1
Reel
Reel
Reel
Reel
Reel
Reel
Reel
Reel
Reel
Std.
Ctn.
Qty.
10
10
10
10
10
10
10
10
10
Reels
Reels
Reels
Reels
Reels
Reels
Reels
Reels
Reels
Black
HSTT05-Q
HSTT06-Q
HSTT09-Q
HSTT12-Q
HSTT19-Q
HSTT25-Q
HSTT38-Q
HSTT50-Q
HSTT75-Q
Flexible Polyolefin DRY -S HRINK
Type
Flexible
Polyolefin Cross-Linked
-67°F to 275° F
AMS-DTL-23053/5
(-55°C to 135°C ) Class 1 or Class 2
(Except Clear)
‡
Shrink Ratio:
2:1
Flame Retardant
(Except Clear)
Variety of Colors
"Q-Box" (25' (7.5M) / Box)
Unique Self-Dispensing Features
‡ Maximum UL temperature range is 125°C
Clear
Red
HSTT100-48-5C
HSTT100-48-LQC
HSTT100-CC
HSTT150-48-5C
HSTT150-CC
HSTT200-48-5C
HSTT200-LC
HSTT300-48-2C
—
HSTT400-48-2C
—
HSTT100-48-5-2
—
HSTT100-C2
HSTT150-48-5-2
HSTT150-C2
HSTT200-48-5-2
HSTT200-L2
—
—
—
—
Clear
HSTT05-QC
HSTT06-QC
HSTT09-QC
HSTT12-QC
HSTT19-QC
HSTT25-QC
HSTT38-QC
HSTT50-QC
HSTT75-QC
Heat Shrink Tubing
Materials
HSTT
600V
™
Red
HSTT05-Q2
HSTT06-Q2
HSTT09-Q2
HSTT12-Q2
HSTT19-Q2
HSTT25-Q2
HSTT38-Q2
HSTT50-Q2
HSTT75-Q2
Yellow
Green
Blue
HSTT100-48-5-4 HSTT100-48-5-5 HSTT100-48-5-6
—
—
—
HSTT100-C4
HSTT100-C5
HSTT100-C6
HSTT150-48-5-4
—
HSTT150-48-5-6
HSTT150-C4
—
HSTT150-C6
HSTT200-48-5-4
—
HSTT200-48-5-6
HSTT200-L4
—
HSTT200-L6
—
—
—
—
—
—
—
—
—
—
—
—
Yellow
HSTT05-Q4
HSTT06-Q4
HSTT09-Q4
HSTT12-Q4
HSTT19-Q4
HSTT25-Q4
HSTT38-Q4
HSTT50-Q4
HSTT75-Q4
Green
HSTT05-Q5
HSTT06-Q5
HSTT09-Q5
HSTT12-Q5
HSTT19-Q5
HSTT25-Q5
HSTT38-Q5
HSTT50-Q5
HSTT75-Q5
Blue
HSTT05-Q6
HSTT06-Q6
HSTT09-Q6
HSTT12-Q6
HSTT19-Q6
HSTT25-Q6
HSTT38-Q6
HSTT50-Q6
HSTT75-Q6
White
Yellow/
Green
HSTT100-48-5-10 HSTT100-48-545
—
—
HSTT100-C10
HSTT100-C45
HSTT150-48-5-10
—
HSTT150-C10
—
HSTT200-48-5-10
—
HSTT200-L10
—
—
—
—
—
—
—
—
—
White
HSTT05-Q10
HSTT06-Q10
HSTT09-Q10
HSTT12-Q10
HSTT19-Q10
HSTT25-Q10
HSTT38-Q10
HSTT50-Q10
HSTT75-Q10
Yellow/
Green
—
—
—
HSTT12-Q45
HSTT19-Q45
HSTT25-Q45
HSTT38-Q45
HSTT50-Q45
HSTT75-Q45
7
Flexible Polyolefin DRY -SHRINK ™ Heat Shrink Tubing
HSTT Heat Shrink
Standard Packs of Heat Shrink — 6" (152.4mm) Pieces
Small package holds unused tube and fits easily
in a tool box
• General purpose heat shrink tubing for dry locations
• Applications include insulating, protecting, harnessing and identifying wires
Type
Materials
HSTT
Polyolefin Cross-Linked
600V
-67° F to 275°F
(-55° C to 135°C‡)
AMS-DTL-23053/5
Class 1 or Class 2
(Except Clear)
Flexible
Shrink Ratio:
2:1
Flame Retardant
(Except Clear)
Variety of Colors
‡ Maximum UL temperature range is 125°C
Ordering Information — HSTT in Standard Packages
Nominal
Diameter
In.
Minimum
Maximum
Expanded
Recovered
I.D. In. (mm) I.D. In. (mm)
Nominal
Recovered
Wall
Thickness
In. (mm)
Length
Total
No.
Pcs.
Std.
Pkg.
Qty.*
Std.
Ctn.
Qty.
Black
1/16"
.063" (1.6)
.031" (0.8)
.017" (0.4)
1 Pc. 6" (152.4mm)
26
1 Pkg.
10 Pkgs. HSTT06-Y**
3/32"
.093" (2.4)
.046" (1.2)
.020" (0.5)
1 Pc. 6" (152.4mm)
24
1 Pkg.
10 Pkgs. HSTT09-Y**
1/8"
.125" (3.2)
.062" (1.6)
.020" (0.5)
1 Pc. 6" (152.4mm)
20
1 Pkg.
10 Pkgs. HSTT12-Y**
3/16"
.187" (4.8)
.093" (2.4)
.020" (0.5)
1 Pc. 6" (152.4mm)
18
1 Pkg.
10 Pkgs. HSTT19-Y**
1/4"
.250" (6.4)
.125" (3.2)
.025" (0.6)
1 Pc. 6" (152.4mm)
14
1 Pkg.
10 Pkgs. HSTT25-Y**
3/8"
.375" (9.5)
.187" (4.8)
.025" (0.6)
1 Pc. 6" (152.4mm)
12
1 Pkg.
10 Pkgs. HSTT38-Y**
1/2"
.500" (12.7)
.250" (6.4)
.025" (0.6)
1 Pc. 6" (152.4mm)
10
1 Pkg.
10 Pkgs. HSTT50-Y**
3/4"
.750" (19.0)
.375" (9.5)
.030" (0.8)
1 Pc. 6" (152.4mm)
8
1 Pkg.
10 Pkgs. HSTT75-Y**
1"
1.00" (25.4)
.500" (12.7)
.035" (0.9)
1 Pc. 6" (152.4mm)
6
1 Pkg.
10 Pkgs. HSTT100-Y**
*Order in multiples of Std. Pkg. Qty.
**For Colors, add C (Clear), 2 (Red), 4 (Yellow), 5 (Green), 6 (Blue) and 10 (White) to end of part number package suffix (Example: HSTT06-YC).
8
Flexible Polyolefin DRY-SHRINK ™ Heat Shrink Tubing
Standard Packs of Heat Shrink — 6" (152.4mm) Pieces
Small package holds unused tube and fits easily in a tool box
• Assor ted colors and diameters available
HSTT– Combination: Black and Colors — Single Diameter
Part Number
HSTT06-YK1
HSTT09-YK1
HSTT12-YK1
HSTT19-YK1
HSTT25-YK1
HSTT38-YK1
HSTT50-YK1
HSTT75-YK1
HSTT100-YK1
Nominal
Diameter
In.
1/16"
3/32"
1/8"
3/16"
1/4"
3/8"
1/2"
3/4"
1"
Minimum
Maximum
Expanded Recovered
I.D. In. (mm) I.D. In. (mm)
.063" (1.6)
.093" (2.4)
.125" (3.2)
.187" (4.8)
.250" (6.4)
.375" (9.5)
.500" (12.7)
.750" (19.0)
1.00" (25.4)
Total No.
Pcs.
Black
No. Pcs.
Each
Color No.
Pcs.
26
24
20
18
14
12
10
8
7
8
6
2
6
2
6
4
2
1
3
3
3
2
2
1
1
1
1
.031" (0.8)
.046" (1.2)
.062" (1.6)
.093" (2.4)
.125" (3.2)
.187" (4.8)
.250" (6.4)
.375" (9.5)
.500" (12.7)
Std.
Pkg.
Qty.*
1
1
1
1
1
1
1
1
1
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Std.
Ctn.
Qty.
10 Pkgs.
10 Pkgs.
10 Pkgs.
10 Pkgs.
10 Pkgs.
10 Pkgs.
10 Pkgs.
10 Pkgs.
10 Pkgs.
*Order in multiples of Std. Pkg. Qty.
NOTE: Colors include Clear, Red, Yellow, Green, Blue and White
HSTT– Black Only — Multiple Diameters
Part Number
HSTT-YK1
HSTT-YK2
Nominal
Total
Black Number
Diameter Number
of Pieces by
In.
of Pieces
Diameter
Various;
Smaller
Range
14
Various;
Larger
Range
8
Std.
Pkg.
Qty.*
Std.
Ctn.
Qty.
(2) pcs. each
1 Pkg. 10 Pkgs.
1/8", 1/16", 3/16",
3/32", 1/4", 1/2",
3/8"
(2) pcs. each
1 Pkg. 10 Pkgs.
3/8", 1/2",
3/4", 1"
*Order in multiples of Std. Pkg. Qty.
HSTT– Yellow/Green Stripe — Multiple Diameters
Part Number
HSTT-YK1-45
HSTT-YK2-45
Nominal
Total
Diameter Number
In.
of Pieces
Various;
Smaller
Range
Various,
Larger
Range
8
6
Number
of Pieces by
Diameter
(2) pcs. each
1/8", 3/16", 1/4",
3/8"
(2) pcs. each
3/8", 1/2",
3/4"
Std.
Pkg.
Qty.*
Std.
Ctn.
Qty.
1 Pkg. 10 Pkgs.
1 Pkg. 10 Pkgs.
*Order in multiples of Std. Pkg. Qty.
9
Flexible Polyolefin DRY -SHRINK ™ Heat Shrink Tubing
HSTTD Heat Shrink in 4' (1.2M) Pieces
with Bar Coded Tags for Distributor
Display Areas
• General purpose heat shrink tubing for
dry locations
• Applications include insulating, protecting,
harnessing and identifying wires
(Except Clear)
(Except Clear)
Ordering Information — HSTTD in Standard Packages
Nominal
Diameter
In.
3/64"
1/16"
3/32"
1/8"
3/16"
1/4"
3/8"
1/2"
3/4"
1"
Minimum
Maximum
Expanded
Recovered
I.D. In. (mm) I.D. In. (mm)
.046" (1.2)
.063" (1.6)
.093" (2.4)
.125" (3.2)
.187" (4.8)
.250" (6.4)
.375" (9.5)
.500" (12.7)
.750" (19.0)
1.00" (25.4)
.023" (0.6)
.031" (0.8)
.046" (1.2)
.062" (1.6)
.093" (2.4)
.125" (3.2)
.187" (4.8)
.250" (6.4)
.375" (9.5)
.500" (12.7)
Nominal
Recovered
Wall
Thickness
In. (mm)
PC
Length
Std.
Pkg.
Qty.*
Black
.016" (0.4)
.017" (0.4)
.020" (0.5)
.020" (0.5)
.020" (0.5)
.025" (0.6)
.025" (0.6)
.025" (0.6)
.030" (0.8)
.035" (0.9)
4' (1.2M)
4' (1.2M)
4' (1.2M)
4' (1.2M)
4' (1.2M)
4' (1.2M)
4' (1.2M)
4' (1.2M)
4' (1.2M)
4' (1.2M)
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
5 Pcs.
5 Pcs.
HSTTD05-48-Q
HSTTD06-48-Q**
HSTTD09-48-Q**
HSTTD12-48-Q**
HSTTD19-48-Q**
HSTTD25-48-Q**
HSTTD38-48-Q**
HSTTD50-48-Q**
HSTTD75-48-5**
‡HSTTD100-48-5**
*Order in multiples of Std. Pkg. Qty.
**For Colors, add C (Clear), 2 (Red), 4 (Yellow), 5 (Green), 6 (Blue) and 10 (White) to end of part number package suffix (Example: HSTTD05-48-QC).
‡ For Colors, add C(Clear), 2 (Red) and 10 (White) to end of part number package suffix (Example: HSTTD100-48-5C)
Ordering Information — HSTT in Pre-Packaged Cut Pieces (Bulk Qty. Only)
1/2" (12.7mm) Lengths
Nominal
Diameter
In.
Bulk
Pkg.
Qty.*
Bulk
Ctn.
Qty.
1/8"
3/16"
1/4"
10,000 Pcs.
10,000 Pcs.
5,000 Pcs.
—
—
—
Black
HSTT12-.5K
HSTT19-.5K
HSTT25-.5F
Clear
HSTT12-.5KC
HSTT19-.5KC
HSTT25-.5FC
*Order in multiples of Bulk Pkg. Qty.
1" (25.4mm) Lengths
Nominal
Diameter
In.
1/8"
3/16"
1/4"
Bulk
Pkg.
Qty.*
Bulk
Ctn.
Qty.
10,000 Pcs.
10,000 Pcs.
5,000 Pcs.
*Order in multiples of Bulk Pkg. Qty.
10
—
—
—
Black
HSTT12-1K
HSTT19-1K
HSTT25-1F
Clear
HSTT12-1KC
HSTT19-1KC
HSTT25-1FC
Flexible Polyolefin VW-1 DRY-SHRINK ™ Heat Shrink Tubing
HSTTV Heat Shrink in 4' (1.2M) Pieces
•
•
•
•
For dry locations
Highly flame retardant
Meets UL VW-1 rating
Fast Shrink Time
Type
Materials
HSTTV
Polyolefin Cross-Linked
600V
-67°F to 257°F
AMS-DTL-23053/5
(-55°C to 125° C )
Class 3
Flexible
VW-1
OFT
‡
Shrink Ratio:
2:1
Highly Flame
Retardant VW-1
HSTTV in Bulk Packages — Small Reels & 4' (1.2M) Pcs.
Part Number
HSTTV05-48-Q
HSTTV05-48-TL
HSTTV05-C
HSTTV06-48-Q
HSTTV06-48-TL
HSTTV06-C
HSTTV09-48-Q
HSTTV09-48-TL
HSTTV09-C
HSTTV12-48-Q
HSTTV12-48-TL
HSTTV12-C
HSTTV19-48-Q
HSTTV19-48-TL
HSTTV19-C
HSTTV25-48-Q
HSTTV25-48-TL
HSTTV25-C
HSTTV38-48-Q
HSTTV38-48-TL
HSTTV38-C
HSTTV50-48-Q
HSTTV50-48-T
HSTTV50-C
HSTTV75-48-5
HSTTV75-48-CQ
HSTTV75-C
HSTTV100-48-5
HSTTV100-48-LQ
HSTTV100-C
HSTTV150-48-5
HSTTV150-C
Nominal
Nominal
Minimum
Maximum Recovered Wall
Diameter Expanded I.D. Recovered I.D.
Thickness
In.
In. (mm)
In. (mm)
In. (mm)
3/64"
.046" (1.2)
.023" (0.6)
Length
.020" (0.5)
1
1/16"
.063" (1.6)
.031" (0.8)
.020" (0.5)
1
3/32"
.093" (2.4)
.046" (1.2)
.020" (0.5)
1
1/8"
.125" (3.2)
.062" (1.6)
.020" (0.5)
1
3/16"
.187" (4.8)
.093" (2.4)
.020" (0.5)
1
1/4"
.250" (6.4)
.125" (3.2)
.025" (0.6)
1
3/8"
.375" (9.5)
.187" (4.8)
.025" (0.6)
1
1/2"
.500" (12.7)
.250" (6.4)
.025" (0.6)
1
3/4"
.750" (19.0)
.375" (9.5)
.030" (0.8)
1
1"
1.00" (25.4)
.500" (12.7)
.035" (0.9)
1 1/2"
1.50" (38.1)
.750" (19.0)
.040" (1.0)
1
1
4' (1.2M)
4' (1.2M)
Reel, 100' (30.5M)
4' (1.2M)
4' (1.2M)
Reel, 100' (30.5M)
4' (1.2M)
4' (1.2M)
Reel, 100' (30.5M)
4' (1.2M)
4' (1.2M)
Reel, 100' (30.5M)
4' (1.2M)
4' (1.2M)
Reel, 100' (30.5M)
4' (1.2M)
4' (1.2M)
Reel, 100' (30.5M)
4' (1.2M)
4' (1.2M)
Reel, 100' (30.5M)
4' (1.2M)
4' (1.2M)
Reel, 100' (30.5M)
4' (1.2M)
4' (1.2M)
Reel, 100' (30.5M)
4' (1.2M)
4' (1.2M)
Reel, 100' (30.5M)
4' (1.2M)
Reel, 100' (30.5M)
Bulk
Pkg.
Qty.*
Bulk
Ctn.
Qty.
25 Pcs.
250 Pcs.
1 Reel
25 Pcs.
250 Pcs.
1 Reel
25 Pcs.
250 Pcs.
1 Reel
25 Pcs.
250 Pcs.
1 Reel
25 Pcs.
250 Pcs.
1 Reel
25 Pcs.
250 Pcs.
1 Reel
25 Pcs.
250 Pcs.
1 Reel
25 Pcs.
200 Pcs.
1 Reel
5 Pcs.
125 Pcs.
1 Reel
5 Pcs.
75 Pcs.
1 Reel
5 Pcs.
1 Reel
—
—
10 Reels
—
—
10 Reels
—
—
10 Reels
—
—
10 Reels
—
—
10 Reels
—
—
10 Reels
—
—
10 Reels
—
—
10 Reels
—
—
10 Reels
—
—
2 Reels
—
2 Reels
* Order in multiples of Bulk Pkg. Qty.
‡ Maximum UL Temperature Range is 125° C
11
Flexible Polyolefin VW-1 DRY -S HRINK ™ Heat Shrink Tubing
HSTTV Heat Shrink Reels
•
•
•
•
For dry locations
Highly flame retardant
Meets UL VW-1 rating
Fast Shrink Time
Type
Materials
HSTTV
Polyolefin Cross-Linked
-67°F to 257°F
AMS-DTL-23053/5
(-55°C to 125°C )
Class 3
600V
VW-1
OFT
‡
Flexible
Shrink Ratio:
2:1
Highly Flame
Retardant VW-1
HSTTV in Bulk Packages — Large Reels
Nominal
Diameter
In.
3/64"
1/16"
3/32"
1/8"
3/16"
1/4"
3/8"
1/2"
3/4"
Length
Black
Red
Yellow
Blue
White
Bulk
Pkg.
Qty.*
1 Reel, 1000' (304.8M)
1 Reel, 1000' (304.8M)
1 Reel, 1000' (304.8M)
1 Reel, 1000' (304.8M)
1 Reel, 1000' (304.8M)
1 Reel, 500' (152.4M)
1 Reel, 200' (61.0M)
1 Reel, 200' (61.0M)
1 Reel, 200' (61.0M)
HSTTV05-M
HSTTV06-M
HSTTV09-M
HSTTV12-M
HSTTV19-M
HSTTV25-D
HSTTV38-T
HSTTV50-T
HSTTV75-T
HSTTV05-M2
HSTTV06-M2
HSTTV09-M2
HSTTV12-M2
HSTTV19-M2
HSTTV25-D2
HSTTV38-T2
HSTTV50-T2
HSTTV75-T2
HSTTV05-M4
HSTTV06-M4
HSTTV09-M4
HSTTV12-M4
HSTTV19-M4
HSTTV25-D4
HSTTV38-T4
HSTTV50-T4
HSTTV75-T4
HSTTV05-M6
HSTTV06-M6
HSTTV09-M6
HSTTV12-M6
HSTTV19-M6
HSTTV25-D6
HSTTV38-T6
HSTTV50-T6
HSTTV75-T6
HSTTV05-M10
HSTTV06-M10
HSTTV09-M10
HSTTV12-M10
HSTTV19-M10
HSTTV25-D10
HSTTV38-T10
HSTTV50-T10
HSTTV75-T10
1 Reel
1 Reel
1 Reel
1 Reel
1 Reel
1 Reel
1 Reel
1 Reel
1 Reel
* Order in multiples of Bulk Pkg. Qty.
‡ Maximum UL Temperature Range is 125° C.
12
Bulk
Ctn.
Qty.
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
Flexible Polyolefin VW-1 DRY -SHRINK ™ Heat Shrink Tubing
HSTTV Heat Shrink in 25' (7.5M) Reels
Ordering Information
HSTTV in Standard Packages of 25' (7.5M) Reels — Black Only
Part Number
Nominal
Nominal
Minimum
Maximum
Recovered Wall
Diameter Expanded I.D. Recovered I.D.
Thickness
In.
In. (mm)
In. (mm)
In. (mm)
Length
Std.
Pkg.
Qty.*
Std.
Ctn.
Qty.
HSTTV05-Q
HSTTV06-Q
3/64"
1/16"
.046" (1.2)
.063" (1.6)
.023" (0.6)
.031" (0.8)
.020" (0.5)
.020" (0.5)
1 Reel, 25' (7.5M)
1 Reel
1 Reel
10 Reels
10 Reels
HSTTV09-Q
3/32"
.093" (2.4)
.046" (1.2)
.020" (0.5)
1 Reel, 25' (7.5M)
1 Reel
10 Reels
HSTTV12-Q
1/8"
.125" (3.2)
.062" (1.6)
.020" (0.5)
1 Reel, 25' (7.5M)
1 Reel
10 Reels
HSTTV19-Q
3/16"
.187" (4.8)
.093" (2.4)
.020" (0.5)
1 Reel, 25' (7.5M)
1 Reel
10 Reels
HSTTV25-Q
1/4"
.250" (6.4)
.125" (3.2)
.025" (0.6)
1 Reel, 25' (7.5M)
1 Reel
10 Reels
HSTTV38-Q
3/8"
.375" (9.5)
.187" (4.8)
.025" (0.6)
1 Reel, 25' (7.5M)
1 Reel
10 Reels
HSTTV50-Q
1/2"
.500" (12.7)
.250" (6.4)
.025" (0.6)
1 Reel, 25' (7.5M)
1 Reel
10 Reels
HSTTV75-Q
3/4"
.750" (19.0)
.375" (9.5)
.030" (0.8)
1 Reel, 25' (7.5M)
1 Reel
10 Reels
HSTTV100-Q
1"
1.00" (25.4)
.500" (12.7)
.035" (0.9)
1 Reel, 25' (7.5M)
1 Reel
2 Reels
1 Reel, 25' (7.5M)
* Order in multiples of Std. Pkg. Qty.
Standard Packs of Heat Shrink — 6" (152.4mm) Pieces
Ordering Information
HSTTV — Single Diameter — Black Only
Part Number
Nominal
Diameter
In.
Minimum
Expanded
I.D. In. (mm)
Maximum
Recovered
I.D. In. (mm)
Total
No.
Pcs.
Black
No. Pcs.
HSTTV05-Y
HSTTV06-Y
HSTTV09-Y
HSTTV12-Y
HSTTV19-Y
HSTTV25-Y
HSTTV38-Y
HSTTV50-Y
HSTTV75-Y
HSTTV100-Y
3/64"
1/16"
3/32"
1/8"
3/16"
1/4"
3/8"
1/2"
3/4"
1"
.046" (1.2)
.063" (1.6)
.093" (2.4)
.125" (3.2)
.187" (4.8)
.250" (6.4)
.375" (9.5)
.500" (12.7)
.750" (19.0)
1.00" (25.4)
.023" (0.6)
.031" (0.8)
.046" (1.2)
.062" (1.6)
.093" (2.4)
.125" (3.2)
.187" (4.8)
.250" (6.4)
.375" (9.5)
.500" (12.7)
26
26
24
20
18
14
12
10
8
6
26
26
24
20
18
14
12
10
8
6
Std.
Pkg.
Qty.*
1
1
1
1
1
1
1
1
1
1
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Std.
Ctn.
Qty.
10
10
10
10
10
10
10
10
10
10
Pkgs.
Pkgs.
Pkgs.
Pkgs.
Pkgs.
Pkgs.
Pkgs.
Pkgs.
Pkgs.
Pkgs.
* Order in multiples of Std. Pkg. Qty.
13
Semi-Rigid Polyolefin DRY -SHRINK ™ Heat Shrink Tubing
HSTTR Heat Shrink
• For dry locations
• Semi-rigid tubing offers excellent protection for delicate components
• Provides strain relief for soldered and crimped connections
Type
Materials
HSTTR
Polyolefin Cross-Linked
600V
-67°F to 275°F
(-55°C to 135° C)
AMS-DTL-23053/6
Class 1
Semi-Rigid
Shrink Ratio:
2:1
Flame Retardant
Ordering Information — HSTTR in Standard Packages — 4' (1.2M) Pieces
Part Number
HSTTR05-48-Q
HSTTR06-48-Q
HSTTR09-48-Q
HSTTR12-48-Q
HSTTR19-48-Q
HSTTR25-48-Q
HSTTR38-48-Q
HSTTR50-48-5
HSTTR75-48-5
HSTTR100-48-5
Nominal
Diameter
In.
Minimum
Expanded
I.D. In. (mm)
Maximum
Recovered
I.D. In. (mm)
Nominal
Recovered
Wall Thickness
In. (mm)
3/64"
1/16"
3/32"
1/8"
3/16"
1/4"
3/8"
1/2"
3/4"
1"
.046" (1.2)
.063" (1.6)
.093" (2.4)
.125" (3.2)
.187" (4.8)
.250" (6.4)
.375" (9.5)
.500" (12.7)
.750" (19.0)
1.00" (25.4)
.023" (0.6)
.031" (0.8)
.046" (1.2)
.062" (1.6)
.093" (2.4)
.125" (3.2)
.187" (4.8)
.250" (6.4)
.375" (9.5)
.500" (12.7)
.020" (0.5)
.020" (0.5)
.020" (0.5)
.020" (0.5)
.025" (0.6)
.025" (0.6)
.030" (0.8)
.030" (0.8)
.030" (0.8)
.035" (0.9)
* Order in multiples of Std. Pkg. Qty.
14
Length
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
Std.
Pkg.
Qty.*
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
5 Pcs.
5 Pcs.
5 Pcs.
PVC DRY -SHRINK ™ Heat Shrink Tubing
HSTTP Heat Shrink
•
•
•
•
For dry locations
Flexible, highly flame retardant tubing
Good resistance to most fuels and oils
Good cut through and solder resistance
Type
Materials
Polyvinyl Chloride
Cross-Linked
HSTTP
600V
-4°F to 221°F
(-20°C to 105°C)
Flexible
Shrink Ratio:
2:1
Highly Flame
Retardant VW-1
Ordering Information — HSTTP in Standard Packages — Reels
Nominal
Diameter
In.
Minimum
Expanded I.D.
In. (mm)
Maximum
Recovered I.D.
In. (mm)
Nominal
Recovered Wall
Thickness
In. (mm)
HSTTP05-Q
HSTTP05-C
HSTTP05-M
3/64"
.046" (1.2)
.023" (0.6)
.020" (0.5)
1 Reel, 25' (7.5M)
1 Reel, 100' (30.5M)
1 Reel, 1000' (304.8M)
1 Reel 10 Reels
1 Reel 2 Reels
1 Reel 2 Reels
HSTTP06-Q
HSTTP06-C
HSTTP06-M
1/16"
.063" (1.6)
.031" (0.8)
.020" (0.5)
1 Reel, 25' (7.5M)
1 Reel, 100' (30.5M)
1 Reel, 1000' (304.8M)
1 Reel 10 Reels
1 Reel 2 Reels
1 Reel 2 Reels
HSTTP09-Q
HSTTP09-C
HSTTP09-M
3/32"
.093" (2.4)
.046" (1.2)
.025" (0.6)
1 Reel, 25' (7.5M)
1 Reel, 100' (30.5M)
1 Reel, 1000' (304.8M)
1 Reel 10 Reels
1 Reel 2 Reels
1 Reel 2 Reels
HSTTP12-Q
HSTTP12-C
HSTTP12-M
1/8"
.125" (3.2)
.062" (1.6)
.025" (0.6)
1 Reel, 25' (7.5M)
1 Reel, 100' (30.5M)
1 Reel, 1000' (304.8M)
1 Reel 10 Reels
1 Reel 2 Reels
1 Reel 2 Reels
HSTTP19-Q
HSTTP19-C
HSTTP19-M
3/16"
.187" (4.8)
.093" (2.4)
.025" (0.6)
1 Reel, 25' (7.5M)
1 Reel, 100' (30.5M)
1 Reel, 1000' (304.8M)
1 Reel 10 Reels
1 Reel 2 Reels
1 Reel 2 Reels
HSTTP25-Q
HSTTP25-C
HSTTP25-D
1/4"
.250" (6.4)
.125" (3.2)
.025" (0.6)
1 Reel, 25' (7.5M)
1 Reel, 100' (30.5M)
1 Reel, 500' (152.4M)
1 Reel 10 Reels
1 Reel 2 Reels
1 Reel 2 Reels
HSTTP38-Q
HSTTP38-C
HSTTP38-T
3/8"
.375" (9.5)
.187" (4.8)
.030" (0.8)
1 Reel, 25' (7.5M)
1 Reel, 100' (30.5M)
1 Reel, 200' (61.0M)
1 Reel 10 Reels
1 Reel 2 Reels
1 Reel 2 Reels
HSTTP50-Q
HSTTP50-C
1/2"
.500" (12.7)
.250" (6.4)
.030" (0.8)
1 Reel, 25' (7.5M)
1 Reel, 100' (30.5M)
1 Reel 10 Reels
1 Reel 2 Reels
HSTTP75-Q
HSTTP75-C
3/4"
.750" (19.0)
.375" (9.5)
.035" (0.9)
1 Reel, 25' (7.5M)
1 Reel, 100' (30.5M))
1 Reel 10 Reels
1 Reel 2 Reels
HSTTP100-Q
HSTTP100-C
1"
1.00" (25.4)
.500" (12.7)
.040" (1.0)
1 Reel, 25' (7.5M)
1 Reel, 100' (30.5M)
1 Reel
1 Reel
2 Reels
2 Reels
HSTTP150-Q
HSTTP150-C
1 1/2"
1.50" (38.1)
.750" (19.0)
.045" (1.1)
1 Reel, 25' (7.5M)
1 Reel, 100' (30.5M)
1 Reel
1 Reel
2 Reels
2 Reels
HSTTP200-X
HSTTP200-Q
2"
2.00" (50.8)
1.00" (25.4)
.050" (1.3)
1 Reel, 10' (3.0m)
1 Reel, 25' (7.5M)
1 Reel
1 Reel
2 Reels
2 Reels
Part Number
Length
Std.
Pkg.
Qty.*
Std.
Ctn.
Qty.
* Order in multiples of Std. Pkg. Qty.
15
Neoprene DRY -S HRINK ™ Heat Shrink Tubing
HSTTN Heat Shrink
• For dry locations
• Highly flexible tubing
• Offers excellent chemical resistance,
especially to fuels and oils
Type
Materials
Elastom er Neoprene
Cross-Linked
HSTTN
600V
-94°F to 250°F
(-70° C to 121°C )
AMS-DT L-23053/1
Class 2
Highly Flexible
Shrink Ratio :
2:1
Highly Flame
Retardant
Ordering Information — HSTTN in Standard Packages — 25' (7.5M) and 100' (30.5M) Reels
Part Number
Nominal
Diameter
In.
Minimum
Expanded I.D.
In. (mm)
Maximum
Recovered I.D.
In. (mm)
Nominal
Recovered Wall
Thickness
In. (mm)
Length
HSTTN25-C
1/4"
.250" (6.4)
.143" (3.6)
.035" (0.9)
1 Reel, 100' (30.5M)
1 Reel 2 Reels
HSTTN38-C
3/8"
.375" (9.5)
.211" (5.4)
.040" (1.0)
1 Reel, 100' (30.5M)
1 Reel 2 Reels
HSTTN50-C
1/2"
.500" (12.7)
.286" (7.3)
.048" (1.2)
1 Reel, 100' (30.5M)
1 Reel 2 Reels
HSTTN63-C
5/8"
.625" (15.9)
.357" (9.1)
.052" (1.3)
1 Reel, 100' (30.5M)
1 Reel 2 Reels
HSTTN75-C
3/4"
.750" (19.0)
.428" (10.9)
.057" (1.5)
1 Reel, 100' (30.5M)
1 Reel 2 Reels
HSTTN88-C
7/8"
.875" (22.2)
.500" (12.7)
.065" (1.7)
1 Reel, 100' (30.5M)
1 Reel 2 Reels
HSTTN100-C
1"
1.00" (25.4)
.570" (14.5)
.070" (1.8)
1 Reel, 100' (30.5M)
1 Reel 2 Reels
HSTTN125-C
1 1/4"
1.25" (31.8)
.714" (18.1)
.087" (2.2)
1 Reel, 100' (30.5M)
1 Reel 2 Reels
HSTTN150-C
1 1/2"
1.50" (38.1)
.857" (21.8)
.095" (2.4)
1 Reel, 100' (30.5M)
1 Reel 2 Reels
HSTTN175-C
1 3/4"
1.75" (44.5)
1.00" (25.4)
.107" (2.7)
1 Reel, 100' (30.5M)
1 Reel 2 Reels
HSTTN200-Q
2"
2.00" (50.8)
1.140" (29.0)
.110" (2.8)
1 Reel, 25' (7.5M)
1 Reel 2 Reels
HSTTN300-Q
3"
3.00" (76.2)
1.710" (43.4)
.125" (3.8)
1 Reel, 25' (7.5M)
1 Reel 2 Reels
Std.
Pkg.
Qty.*
* Order in multiples of Std. Pkg. Qty.
Shrink ratios are approximations; please refer to above ordering information for the exact Min. Expanded and Max. Recovered I.D.’s.
16
Std.
Ctn.
Qty.
TFE TEFLON ‡ DRY-SHRINK ™ Heat Shrink Tubing
HSTTT (TFE)
Heat Shrink
• For dry locations
• Semi-rigid, highly heat resistant
• Offers the widest temperature
range of any plastic material
• Also available with 4:1
shrink ratio
• Color is milky clear
Type
HSTTT
HSTTT4X
NOTE: Special instructions on page 28
Materials
Polytetr afluoroethylene
600V
-88°F to 482° F
(-67°C to 250°C )
AMS-DTL-23053/12
Class 3 or Class 5
Semi-Rigid
Shrink Ratio :
2:1 or 4:1
Non-Flammable
Ordering Information — 2:1 Shrink Ratio (Class 3) — HSTTT in Standard Packages — 4' (1.2M) Pcs.
Part Number
HSTTT03-48-Q
HSTTT04-48-Q
HSTTT046-48-Q
HSTTT05-48-Q
HSTTT055-48-Q
HSTTT06-48-Q
HSTTT08-48-Q
HSTTT09-48-Q
HSTTT12-48-Q
HSTTT15-48-Q
HSTTT19-48-Q
HSTTT24-48-Q
HSTTT30-48-Q
HSTTT37-48-Q
HSTTT43-48-Q
HSTTT47-48-Q
HSTTT56-48-5
HSTTT66-48-5
HSTTT75-48-5
HSTTT93-48-5
HSTTT112-48-5
HSTTT131-48-2
HSTTT150-48-2
Nominal
Diameter
Minimum
Expanded I.D.
In. (mm)
Maximum
Recovered I.D.
In. (mm)
30 AWG
28 AWG
26 AWG
24 AWG
22 AWG
20 AWG
18 AWG
16 AWG
14 AWG
12 AWG
10 AWG
8 AWG
6 AWG
4 AWG
2 AWG
0 AWG
9/16"
5/8"
3/4"
15/16"
1 1/8"
1 5/16"
1 1/2"
.034" (0.9)
.038" (1.0)
.046" (1.2)
.050" (1.3)
.055" (1.4)
.060" (1.5)
.076" (1.9)
.093" (2.3)
.120" (3.0)
.150" (3.8)
.191" (4.9)
.240" (6.0)
.302" (7.7)
.370" (9.4)
.430" (10.9)
.470" (11.9)
.560" (14.2)
.655" (16.6)
.750" (19.0)
.930" (23.6)
1.125" (28.6)
1.310" (33.3)
1.500" (38.1)
.015" (0.4)
.018" (0.5)
.022" (0.5)
.027" (0.7)
.032" (0.8)
.039" (1.0)
.049" (1.2)
.061" (1.6)
.072" (1.8)
.089" (2.3)
.112" (2.8)
.141" (3.6)
.178" (4.5)
.224" (5.7)
.278" (7.0)
.347" (8.8)
.399" (10.1)
.462" (11.7)
.524" (13.3)
.655" (16.6)
.786" (20.0)
.911" (23.1)
1.036" (26.3)
Nominal Recovered
Wall Thickness
In. (mm)
.009"
.009"
.010"
.010"
.012"
.012"
.012"
.012"
.012"
.012"
.012"
.015"
.015"
.015"
.015"
.015"
.015"
.018"
.018"
.020"
.025"
.030"
.030"
(0.2)
(0.2)
(0.3)
(0.3)
(0.3)
(0.3)
(0.3)
(0.3)
(0.3)
(0.3)
(0.3)
(0.4)
(0.4)
(0.4)
(0.4)
(0.4)
(0.4)
(0.5)
(0.5)
(0.5)
(0.6)
(0.8)
(0.8)
Length
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
Std.
Pkg.
Qty.*
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
5 Pcs.
5 Pcs.
5 Pcs.
5 Pcs.
5 Pcs.
2 Pcs.
2 Pcs.
Ordering Information — 4:1 Shrink Ratio (Class 5) — HSTTT4X in Standard Packages — 4' (1.2M) Pcs.
Part Number
Nominal
Diameter
In. (mm)
HSTTT4X08-48-Q 5/64" (2.0)
HSTTT4X12-48-Q 1/8" (3.3)
HSTTT4X25-48-Q 1/4" (6.3)
HSTTT4X38-48-Q 3/8" (9.5)
HSTTT4X50-48-5 1/2" (12.7)
HSTTT4X63-48-5 5/8" (15.9)
HSTTT4X75-48-5 3/4" (19.1)
HSTTT4X88-48-5 7/8" (22.2)
HSTTT4X100-48-5 1" (25.4)
HSTTT4X125-48-5 1 1/4" (31.8)
Minimum
Expanded I.D.
In. (mm)
Maximum
Recovered I.D.
In. (mm)
.078" (2.0)
.125" (3.2)
.250" (6.4)
.375" (9.5)
.500" (12.7)
.625" (15.9)
.750" (19.1)
.875" (22.2)
1.00" (25.4)
1.25" (31.8)
.025" (0.6)
.037" (0.9)
.063" (1.6)
.096" (2.4)
.144" (3.7)
.178" (4.5)
.224" (5.7)
.244" (6.2)
.278" (7.0)
.347" (8.8)
Nominal Recovered
Wall Thickness
In. (mm)
.009"
.012"
.012"
.012"
.015"
.015"
.015"
.015"
.015"
.015"
(0.2)
(0.3)
(0.3)
(0.3)
(0.4)
(0.4)
(0.4)
(0.4)
(0.4)
(0.4)
Length
1
1
1
1
1
1
1
1
1
1
Pc., 4’ (1.2M)
Pc., 4’ (1.2M)
Pc., 4’ (1.2M)
Pc., 4’ (1.2M)
Pc., 4’ (1.2M)
Pc., 4’ (1.2M)
Pc., 4’ (1.2M)
Pc., 4’ (1.2M)
Pc., 4’ (1.2M)
Pc., 4’ (1.2M)
Std.
Pkg.
Qty.*
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
5 Pcs.
5 Pcs.
5 Pcs.
5 Pcs.
5 Pcs.
5 Pcs.
* Order in multiples of Std. Pkg. Qty.
Shrink ratios are approximations; please refer to above ordering information for the exact Min. Expanded and Max. Recovered I.D.’s.
‡ TEFLON
is a registered trademark of E.I. DuPont.
17
FEP TEFLON‡ DRY-S HRINK ™ Heat Shrink Tubing
HSTTF (FEP) Heat Shrink
• For dry locations
• Semi-rigid, highly heat resistant tubing
• Offers most of the same characteristics of HSTTT found on
page 17, but has a lower shrink temperature
• Tubing can be welded and tube ends sealed by melting
• Color is clear
Type
Materials
Fluorinated Ethylene
Propylene
HSTTF
600V
-88°F to 392°F
(-67° C to 200°C)
AMS-DTL-23053/
11
Semi-Rigid
Shrink Ratio :
1.3:1
Non-Flammable
Ordering Information — HSTTF in Standard Packages — 4' (1.2M) Pieces
Part Number
Nominal
Diameter
Minimum
Expanded I.D.
In. (mm)
Maximum
Recovered I.D.
In. (mm)
HSTTF03-48-Q
HSTTF04-48-Q
HSTTF05-48-Q
HSTTF06-48-Q
HSTTF08-48-Q
HSTTF09-48-Q
HSTTF12-48-Q
HSTTF14-48-Q
HSTTF16-48-Q
HSTTF18-48-Q
HSTTF20-48-Q
HSTTF23-48-Q
HSTTF25-48-Q
HSTTF29-48-Q
HSTTF31-48-Q
HSTTF36-48-Q
HSTTF40-48-Q
HSTTF44-48-Q
HSTTF50-48-5
HSTTF66-48-5
HSTTF100-48-5
HSTTF133-48-2
HSTTF200-48-2
24 AWG
22 AWG
20 AWG
18 AWG
16 AWG
14 AWG
12 AWG
10 AWG
9 AWG
8 AWG
7 AWG
6 AWG
5 AWG
4 AWG
3 AWG
2 AWG
1 AWG
0 AWG
1/2"
5/8"
1"
1 1/3"
2"
.031" (0.8)
.036" (0.9)
.045" (1.1)
.060" (1.5)
.075" (1.9)
.092" (2.3)
.115" (2.9)
.141" (3.6)
.158" (4.0)
.180" (4.6)
.197" (5.0)
.225" (5.7)
.248" (6.3)
.290" (7.4)
.310" (7.9)
.365" (9.3)
.400" (10.2)
.440" (11.2)
.500" (12.7)
.666" (16.9)
1.00" (25.4)
1.33" (33.8)
2.00" (50.8)
.027" (0.7)
.032" (0.8)
.039" (1.0)
.049" (1.2)
.061" (1.5)
.072" (1.8)
.089" (2.2)
.114" (2.9)
.124" (3.2)
.143" (3.6)
.158" (4.0)
.180" (4.6)
.198" (5.0)
.226" (5.7)
.249" (6.3)
.280" (7.1)
.311" (7.9)
.349" (8.9)
.383" (9.7)
.510" (13.0)
.764" (19.4)
1.02" (25.9)
1.52" (38.6)
Nominal
Recovered
Wall Thickness
In. (mm)
.008"
.008"
.008"
.008"
.009"
.009"
.009"
.010"
.010"
.010"
.011"
.011"
.011"
.011"
.011"
.012"
.012"
.012"
.015"
.020"
.030"
.035"
.035"
(0.2)
(0.2)
(0.2)
(0.2)
(0.2)
(0.2)
(0.2)
(0.3)
(0.3)
(0.3)
(0.3)
(0.3)
(0.3)
(0.3)
(0.3)
(0.3)
(0.3)
(0.3)
(0.4)
(0.5)
(0.8)
(0.9)
(0.9)
Length
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Pc., 4' (1.2M)
Pc., 4' (1.2M)
Pc., 4' (1.2M)
Pc., 4' (1.2M)
Pc., 4' (1.2M)
Pc., 4' (1.2M)
Pc., 4' (1.2M)
Pc., 4' (1.2M)
Pc., 4' (1.2M)
Pc., 4' (1.2M)
Pc., 4' (1.2M)
Pc., 4' (1.2M)
Pc., 4' (1.2M)
Pc., 4' (1.2M)
Pc., 4' (1.2M)
Pc., 4' (1.2M)
Pc., 4' (1.2M)
Pc., 4' (1.2M)
Pc., 4' (1.2M)
Pc., 4' (1.2M)
Pc., 4' (1.2M)
Pc., 4' (1.2M)
Pc., 4' (1.2M)
Std.
Pkg.
Qty.*
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
5 Pcs.
5 Pcs.
5 Pcs.
2 Pcs.
2 Pcs.
* Order in multiples of Std. Pkg. Qty.
Shrink ratios are approximations; please refer to above ordering information for the exact Min. Expanded and Max. Recovered I.D.’s.
18
‡ TEFLON
is a registered trademark of E.I. DuPont.
KYNAR‡ DRY-SHRINK ™ Heat Shrink Tubing
HSTTK KYNAR‡ Heat Shrink
•
•
•
•
•
For dry locations
Semi-rigid, highly heat resistant
Offers excellent chemical and abrasion resistance
Use in high temperature or solvent rich environment
Color is clear
Type
Material
Polyvinylidene Fluoride
HSTTK
600V
-67°F to 347° F
(-55°C to 175°C )
Semi-Rigid
Shrink Ratio :
2:1
AMS-DTL-23053/8
VW-1
Highly Flame
Retardant VW-1
Ordering Information — HSTTK in Standard Packages — 4' (1.2M) Pieces
Part Number
HSTTK05-48-Q
HSTTK06-48-Q
HSTTK09-48-Q
HSTTK12-48-Q
HSTTK19-48-Q
HSTTK25-48-Q
HSTTK38-48-Q
HSTTK50-48-5
HSTTK75-48-5
HSTTK100-48-5
Nominal
Diameter
In.
Minimum
Expanded I.D.
In. (mm)
Maximum
Recovered I.D.
In. (mm)
Nominal
Recovered
Wall Thickness
In. (mm)
3/64"
1/16"
3/32"
1/8"
3/16"
1/4"
3/8"
1/2"
3/4"
1"
.046" (1.2)
.063" (1.6)
.093" (2.4)
.125" (3.2)
.187" (4.8)
.250" (6.4)
.375" (9.5)
.500" (12.7)
.750" (19.0)
1.00" (25.4)
.023" (0.6)
.031" (0.8)
.046" (1.2)
.062"(1.6)
.093" (2.4)
.125"(3.2)
.187" (4.8)
.250" (6.4)
.375" (9.5)
.500" (12.7)
.010" (0.3)
.010" (0.3)
.010" (0.3)
.010" (0.3)
.010" (0.3)
.010" (0.3)
.012" (0.3)
.012" (0.3)
.017" (0.4)
.019" (0.5)
Length
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
1 Pc., 4'
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
(1.2M)
Std.
Pkg.
Qty.*
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
5 Pcs.
5 Pcs.
5 Pcs.
* Order in multiples of Std. Pkg. Qty.
Shrink ratios are approximations; please refer to above ordering information for the exact Min. Expanded and Max. Recovered I.D.’s.
‡ KYNAR is a registered trademark of Elf Atochem.
19
Dual Wall Polyolefin DAMP -S HRINK ™ Heat Shrink Tubing
HSTTVA Heat Shrink
• For damp locations
• Flexible tubing with an adhesive inner wall which seals
and protects components from moisture and corrosion
• For use when a flexible adhesive lined tubing is needed
Type
Materials
Polyolefin Cross-Linked
with Adhesive
HSTTVA
600V
-67°F to 230°F
(-55°C to 110° C)
AMS-DTL-23053/4
Class 2
Flexible
Shrink Ratio:
2:1
Outer Wall
Flame Retardant
Ordering Information — HSTTVA in Standard Packages — 4' (1.2M) Pieces
Part Number
HSTTVA12-48-Q
HSTTVA19-48-Q
HSTTVA25-48-Q
HSTTVA38-48-Q
HSTTVA50-48-5
HSTTVA75-48-5
HSTTVA100-48-5
HSTTVA150-48-5
Nominal
Diameter
In.
1/8"
3/16"
1/4"
3/8"
1/2"
3/4"
1"
1 1/2"
Minimum
Maximum
Expanded I.D. Recovered I.D.
In. (mm)
In. (mm)
.125" (3.2)
.187" (4.8)
.250" (6.4)
.375" (9.5)
.500" (12.7)
.750" (19.0)
1.00" (25.4)
1.50" (38.1)
.062" (1.6)
.093" (2.4)
.125" (3.2)
.187" (4.8)
.250" (6.4)
.375" (9.5)
.500" (12.7)
.750" (19.0)
Nominal
Recovered Wall
Thickness
In. (mm)
.020"
.022"
.030"
.031"
.032"
.037"
.046"
.049"
(0.5)
(0.6)
(0.8)
(0.8)
(0.8)
(0.9)
(1.2)
(1.2)
Length
Std.
Pkg.
Qty.*
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
5 Pcs.
5 Pcs.
5 Pcs.
5 Pcs.
* Order in multiples of Std. Pkg. Qty.
Standard Packs of HSTTVA Heat Shrink — 6" (152.4mm) Pieces
HSTTVA– 2:1 Adhesive Lined – Black Only – Single Diameter
Part Number
HSTTVA12-Y
HSTTVA19-Y
HSTTVA25-Y
HSTTVA38-Y
HSTTVA50-Y
HSTTVA75-Y
HSTTVA100-Y
Nominal
Minimum
Maximum
Total
Diameter Expanded I.D. Recovered I.D. No. of
In.
In. (mm)
In. (mm)
Pieces
1/8"
3/16"
1/4"
3/8"
1/2"
3/4"
1"
*Order in multiples of Std. Pkg. Qty.
20
.125" (3.2)
.187" (4.8)
.250" (6.4)
.375" (9.5)
.500" (12.7)
.750" (19.0)
1.00" (25.4)
.062" (1.6)
.093" (2.4)
.125" (3.2)
.187" (4.8)
.250" (6.4)
.375" (9.5)
.500" (12.7)
7
7
5
4
4
3
2
Std.
Pkg.
Qty.*
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
Std.
Ctn.
Qty.
10
10
10
10
10
10
10
Pkgs.
Pkgs.
Pkgs.
Pkgs.
Pkgs.
Pkgs.
Pkgs.
Dual Wall Polyolefin DAMP-S HRINK ™ Heat Shrink Tubing
HSTTA Heat Shrink
• For damp locations
• Flexible tubing with adhesive inner wall, seals and protects components
from moisture and corrosion
• The 3:1 shrink ratio is a benefit when working with connector to
cable transitions
Type
Materials
Polyolefin CrossLinked with Adhesive
HSTTA
600V
-67°F to 230°F
(-55°C to 110° C)
AMS-DTL-23053/4
Class 3
Flexible
Shrink Ratio:
3:1
Outer Wall
Flame Retardant
Ordering Information — HSTTA in Standard and Bulk Packages — 4' (1.2M) Pieces
Part Number
HSTTA19-48-Q
HSTTA25-48-Q
HSTTA25-48-TL
HSTTA38-48-Q
HSTTA38-48-TL
HSTTA50-48-5
HSTTA50-48-T
HSTTA75-48-5
HSTTA75-48-C
HSTTA100-48-5
HSTTA100-48-L
HSTTA150-48-5
HSTTA150-48-Q
Nominal
Diameter
In.
3/16"
1/4"
1/4"
3/8"
3/8"
1/2"
1/2"
3/4"
3/4"
1"
1"
1 1/2"
1 1/2"
Minimum
Expanded I.D.
In. (mm)
.187" (4.8)
.250" (6.4)
.250" (6.4)
.375" (9.5)
.375" (9.5)
.500" (12.7)
.500" (12.7)
.750" (19.0)
.750" (19.0)
1.00" (25.4)
1.00" (25.4)
1.50" (38.1)
1.50" (38.1)
Maximum
Recovered I.D.
In. (mm)
.062" (1.6)
.080" (2.0)
.080" (2.0)
.120" (3.0)
.120" (3.0)
.160" (4.1)
.160" (4.1)
.250" (6.4)
.250" (6.4)
.320" (8.1)
.320" (8.1)
.510" (12.9)
.510" (12.9)
Nominal Recovered
Wall Thickness
In. (mm)
.040" (1.0)
.040" (1.0)
.040" (1.0)
.055" (1.4)
.055" (1.4)
.070" (1.8)
.070" (1.8)
.085" (2.2)
.085" (2.2)
.100" (2.5)
.100" (2.5)
.100" (2.5)
.100" (2.5)
Length
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
Std.
Pkg.
Qty.*
25 Pcs.
25 Pcs.
250 Pcs.
25 Pcs.
250 Pcs.
5 Pcs.
200 Pcs.
5 Pcs.
100 Pcs.
5 Pcs.
50 Pcs.
5 Pcs.
25 Pcs.
* Order in multiples of Std. Pkg. Qty.
Shrink ratios are approximations; please refer to above ordering information for the exact Min. Expanded and Max. Recovered I.D.’s.
Standard Packs of HSTTA Heat Shrink — 6" (152.4mm) Pieces
HSTTA– Black Only – Single Diameter
Part Number
HSTTA19-Y
HSTTA25-Y
HSTTA38-Y
HSTTA50-Y
HSTTA75-Y
HSTTA100-Y
HSTTA150-Y
Nominal
Minimum
Maximum
Total
Diameter Expanded I.D. Recovered I.D. No. of
In.
In. (mm)
In. (mm)
Pieces
3/16"
1/4"
3/8"
1/2"
3/4"
1"
1 1/2"
.187" (4.8)
.250" (6.4)
.375" (9.5)
.500" (12.7)
.750" (19.0)
1.00" (25.4)
1.50" (38.1)
.062" (1.6)
.080" (2.0)
.120" (3.0)
.160" (4.1)
.250" (6.4)
.320" (8.1)
.510" (12.9)
6
4
3
3
2
2
1
Std.
Pkg.
Qty.*
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
Std.
Ctn.
Qty.
10
10
10
10
10
10
10
Pkgs.
Pkgs.
Pkgs.
Pkgs.
Pkgs.
Pkgs.
Pkgs.
*Order in multiples of Std. Pkg. Qty.
Shrink ratios are approximations; please refer to above ordering information for the exact Min. Expanded and Max. Recovered I.D.’s.
21
Dual Wall Polyolefin DAMP -SHRINK ™ Heat Shrink Tubing
HSTTRA Heat Shrink
• For damp locations
• Semi-rigid tubing
• Adhesive inner wall which seals and protects
components from moisture and corrosion
• Provides a rugged seal from the elements
Type
Materials
Polyolefin Cross-Linked
with Adhesive
HSTTRA
600V
Semi-Rigid
-67°F to 230°F
(-55°C to 110° C)
AMS-DTL-23053/4
Class 1
Shrink Ratio :
2.5:1
Ordering Information — HSTTRA in Standard Packages — 4' (1.2M) Pieces
Part Number
HSTTRA12-48-Q
HSTTRA19-48-Q
HSTTRA25-48-Q
HSTTRA38-48-Q
HSTTRA50-48-5
HSTTRA75-48-5
HSTTRA100-48-5
Nominal
Diameter
In.
Minimum
Expanded I.D.
In. (mm)
Maximum
Recovered I.D.
In. (mm)
Nominal
Recovered Wall
Thickness
In. (mm)
Length
Std.
Pkg.
Qty.*
1/8"
3/16"
1/4"
3/8"
1/2"
3/4"
1"
.125" (3.2)
.187" (4.8)
.250" (6.4)
.375" (9.5)
.500" (12.7)
.750" (19.0)
1.00" (25.4)
.023" (0.6)
.060" (1.5)
.080" (2.0)
.135" (3.4)
.195" (5.0)
.313" (8.0)
.400" (10.6)
.038" (1.0)
.043" (1.1)
.047" (1.2)
.050" (1.3)
.059" (1.5)
.065" (1.7)
.075" (1.9)
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
1 Pc., 4' (1.2M)
25 Pcs.
25 Pcs.
25 Pcs.
25 Pcs.
5 Pcs.
5 Pcs.
5 Pcs.
* Order in multiples of Std. Pkg. Qty.
Shrink ratios are approximations; please refer to above ordering information for the exact Min. Expanded and Max. Recovered I.D.’s.
22
Thick Wall Polyolefin WET-SHRINK ™ Heat Shrink Tubing
HST Thick Wall Heat Shrink
• Suitable for wet locations and direct burial according to UL 486D
• Provides excellent protection above or below ground level
• Adhesive lined inner wall seals and protects against moisture
Type
Material
Polyolefin Cross-Linked
with Adhesive
HST
(Black Only)
Including HST3.0
600V
-85°F to 230°F
(-65°C to 110° C)
AMS-DTL-23053/15
(HST only)
Listed 6R72
(except HST3.0)
Rigid
Shrink Ratio :
3:1
Flame Retardant
Thick Wall Heat Shrink Part Number System
HST
Type
HST
0.4 -
Expanded Diameter
0.4 - .40" (10.2mm)
0.8 - .80" (20.3mm)
1.1 - 1.10" (27.9mm)
1.5 - 1.50" (38.1mm)
2.0 - 2.00" (50.8mm)
3.0 - 3.00" (76.2mm)
3
-
Q
2
PC Length
3 - 3" (76.2mm)
6 - 6" (152.4mm)
9 - 9" (228.6mm)
12 - 12" (304.8mm)
48 - 4' (1.2M)
Package Quantity
1 - 1 Pc.
2 - 2 Pcs.
3 - 3 Pcs.
5 - 5 Pcs.
X - 10 Pcs.
Q - 25 Pcs.
Color
None - Black
2 - Red
Ordering Information — HST in Standard Packages
Part
Number
HST0.4-3-Q‡
HST0.4-6-3
HST0.4-6-X‡
HST0.4-48-5‡
HST0.8-6-3
HST0.8-6-X‡
HST0.8-9-X‡
HST0.8-12-5‡
HST0.8-48-5‡
HST1.1-6-3
HST1.1-6-X‡
HST1.1-9-2
HST1.1-9-X‡
HST1.1-12-5‡
HST1.1-48-5‡
HST1.5-9-X
HST1.5-12-1
HST1.5-12-5
HST1.5-48-5
HST2.0-9-5
HST2.0-12-2
HST2.0-48-2
HST3.0-12-2
HST3.0-48-2
Minimum
Expanded
I.D.
In. (mm)
Maximum
Recovered
I.D.
In. (mm)
Nominal
Recovered
Wall Thickness
In. (mm)
Conductor
Size Range
AWG/MCM
(mm )
Minimum
Cable O.D.
In. (mm)
Maximum
Connector
O.D.
In. (mm)
.40" (10.1)
.15" (3.8)
.09" (2.3)
#12-#6
(4-10)
0.170"
(4.3)
.350"
(8.9)
.80" (20.3)
.20" (5.1)
.11" (2.8)
#8-#1/0
(10-50)
.240"
(6.1)
.650"
(16.5)
1.10" (27.9)
.37" (9.4)
.12" (3.0)
#2-#4/0
(35-95)
.400"
(10.1)
.875"
(22.2)
1.50" (38.1)
.50" (12.7)
.17" (4.3)
#3/0-400 MCM
(95-185)
.600"
(15.2)
1.190"
(30.2)
2.00" (50.8)
.65" (16.5)
.17" (4.3)
250-750 MCM
(240-500)
.750"
(19.1)
1.600"
(40.6)
3.00"(76.2)
1.00" (25.4)
.17" (4.3)
600-1250 MCM
(300-625)
1.20"
(30.5)
2.250"
(57.2)
2
Tube
Length
In. (mm)
Std.
Pkg.
Qty.*
Std.
Ctn.
Qty.
3" (76.2)
6" (152.4)
6" (152.4)
4' (1.2M)
6" (152.4)
6" (152.4)
9" (228.6)
12" (304.8)
4' (1.2M)
6" (152.4)
6" (152.4)
9" (228.6)
9" (228.6)
12" (304.8)
4' (1.2M)
9" (228.6)
12" (304.8)
12" (304.8)
4' (1.2M)
9" (228.6)
12" (304.8)
4' (1.2M)
12" (304.8)
4' (1.2M)
25 PC S.
3 P C S.
10 PC S.
5 P C S.
3 P C S.
10 PC S.
10 PC S.
5 P C S.
5 P C S.
3 P C S.
10 PC S.
2 P C S.
10 PC S.
5 P C S.
5 P C S.
10 PC S.
1 PC.
5 P C S.
5 P C S.
5 P C S.
2 P C S.
2 P C S.
2 P C S.
2 P C S.
100 P CS.
30 PC S.
100 P CS.
20 PC S.
30 PC S.
100 P CS.
100 P CS.
50 PC S.
20 PC S.
30 PC S.
100P CS.
20 PC S.
100 P CS.
50 PC S.
20 PC S.
100 P CS.
10 PC S.
50 PC S.
20 PC S.
50 PC S.
20 PC S.
8 PC S.
20 PC S.
8 PC S.
* Order in multiples of Std Pkg. Qty.
‡ For Red, add 2 to end of part number package suffix (Example HST0.4-3-Q2).
Shrink ratios are approximations; please refer to above ordering information for the exact Min. Expanded and Max. Recovered I.D.’s.
23
Polyolefin WET-SHRINK ™ Thick Wall End Caps
HSEC Thick Wall End Caps
• For wet locations
• Provides excellent protection for sealing ends of wire or cable
• Adhesive lined inner wall seals and protects against moisture
Type
Materials
Polyolefin Cross-Linked
with Adhesive
HSEC
600V
-67°F to 221° F
(-55°C to 105°C )
Rigid
Shrink Ratio :
3:1
Thick Wall End Caps Part Number System
HSEC - 0.5
Type
HSEC
-
X
Expanded Diameter
0.5 - .47" (11.9mm)
0.8 - .79" (20.1mm)
1.0 - 1.02" (25.9mm)
1.5 - 1.58" (40.1mm)
2.0 - 2.25" (57.2mm)
4.0 - 4.14" (105.2mm)
Package Quantity
2 - 2 Pcs.
5 - 5 Pcs.
X - 10 Pcs.
Ordering Information — Thick Wall End Caps in Standard Packages
Part
Number
Minimum
Expanded
I.D.
In. (mm)
HSEC0.5-X
HSEC0.8-X
HSEC1.0-X
HSEC1.5-5
HSEC2.0-5
HSEC4.0-2
.47" (11.9)
.79" (20.1)
1.02" (25.9)
1.58" (40.1)
2.25" (57.2)
4.14" (105.2)
Nominal
Maximum
Recovered
Recovered Wall Thickness
I.D. In. (mm)
In. (mm)
.18" (4.6)
.30" (7.6)
.45" (11.4)
.68" (17.3)
.87" (22.1)
1.78" (45.2)
.10" (2.5)
.10" (2.5)
.10" (2.5)
.11" (2.8)
.15" (3.8)
.15" (3.8)
Conductor
Size
2
#8 TO #4 AWG (10 TO 25mm )
#4 TO 3/0 AWG (25 TO 95mm )
#2 TO 4/0 AWG (35 TO 95mm )
250 TO 500 MCM (120 TO 240mm )
600 TO 1000 MCM (300 TO 500mm )
1500 TO 2000 MCM (720 TO 1000mm )
2
2
2
2
2
Cap Length
In. (mm)
Std.
Pkg.
Qty.*
Std.
Ctn.
Qty.
1.38" (35.1)
2.13" (54.1)
3.23" (82.0)
3.86" (98.0)
5.52" (140.2)
6.90" (175.3)
10 P CS .
10 P CS .
10 P CS .
5 PCS.
5 PCS.
2 PCS.
100 P C S.
100 P C S.
100 P C S.
50 P CS.
50 P CS.
10 P CS.
* Order in multiples of Std. Pkg. Qty.
Shrink ratios are approximations; please refer to above ordering information for the exact Min. Expanded and Max. Recovered I.D.’s.
24
Heat Shrink Tubing Kits
Plastic Kit Boxes
• Provides organized storage for a wide variety of parts in one convenient location
• Informative label eliminates guess work:
— Specifies correct heat shrink usage based on wire range and connector size
— Provides reorder part number information
• Once top is closed, loose pieces remain in their 6 compar tments
• Available with non-adhesive or adhesive lined heat shrink tubing for dry and damp locations
KP-HSTT1 Contents
For Dry Locations
B L ACK P OLYOL EFIN DR Y-SH R INK ™ HEAT S HR IN K TU BING (TYPE HSTT)
IN 6" (152.4mm) L EN GTHS
2:1 SH R IN K RA TIO
AMS-DTL-23053/5
CLA SS 1
35 E AC H
HSTT09 3/32" (2.4mm) I.D.
HSTT12 1/8" (3.2mm) I.D.
21 E AC H
HSTT19 3/16" (4.8mm) I.D.
HSTT25 1/4" (6.4mm) I.D.
KP-HSTT2 Contents
7 EA CH
HSTT38 3/8" (9.5mm) I.D.
HSTT50 1/2" (12.7mm) I.D.
For Dry Locations
M UL TIPLE COLOR POLY OLEFIN DR Y-S HR IN K HEAT S HR INK TUBIN G (TY PE HSTT)
IN 6" (152.4mm) LEN GTHS
2:1 S HR IN K RATIO
(Except Clear)
35 EA CH
HSTT09 3/32" (2.4mm) I.D.
- 7 COL ORS
HSTT12 1/8" (3.2mm) I.D.
- 7 COL ORS
(Except Clear)
21 EA CH
HSTT19 3/16" (4.8mm) I.D.
- 7 COL ORS
HSTT25 1/4" (6.4mm) I.D.
- 7 COL ORS
AMS-DTL-23053/5
CL ASS 1 & 2
7 EAC H
HSTT38 3/8" (9.5mm) I.D.
- 7 COL ORS
HSTT50 1/2" (12.7mm) I.D.
- 7 COL ORS
Note: Colors include: Red, Yellow, Green, Blue, White, Clear and Black
KP-HSTTA Contents
For Damp Locations
A DH ESIVE L IN ED B L ACK P OLYOL EFIN DA MP-SH R IN K ™ HE AT SH R INK TUBIN G (TY PE HSTTA)
IN 6" (152.4mm) LE NGTH S
3:1 S HR INK RATIO
AMS-DTL-23053/4
CL AS S 3
14 EAC H
HSTTA19 3/16" (4.8mm) I.D.
10 EAC H
HSTTA38 3/8" (9.5mm) I.D.
3 E AC H
HSTTA75 3/4" (19.0mm) I.D.
12 EAC H
HSTTA25 1/4" (6.4mm) I.D.
6 E AC H
2 E AC H
HSTTA50 1/2" (12.7mm) I.D. HSTTA100 1" (25.4mm) I.D.
Order number of kits required.
25
Heat Shrink Tubing Kits
Metal Kit Boxes
• Provides organized storage for a wide variety of parts in one convenient location
• Informative label eliminates guesswork:
— Specifies correct heat shrink usage based on wire range and connector size
— Provides reorder part number information
• Once top is closed, loose pieces remain in their 8 compar tments
• Available with non-adhesive or adhesive lined heat shrink tubing for dry and damp locations
K-HSTT1 Contents
For Dry Locations
BL ACK POLYOL EFIN DR Y -SHR INK ™ HE AT SH R IN K TU BIN G (TY PE HSTT)
IN 6" (152.4mm) LE NGTH S
2:1SH RIN KRATIO
AMS-DTL-23053/5
CL ASS 1
42 EAC H
HSTT06 1/16" (1.6mm) I.D.
HSTT12 1/8" (3.2mm) I.D.
K-HSTT2 Contents
28 EAC H
HSTT19 3/16" (4.8mm) I.D.
21 EAC H
HSTT25 1/4" (6.4mm) I.D.
14 EAC H
HSTT38 3/8" (9.5mm) I.D.
7 E ACH
HSTT50 1/2" (12.7mm) I.D.
HSTT75 3/4" (19.0mm) I.D.
HSTT100 1" (25.4mm) I.D.
For Dry Locations
M UL TIPLE COLOR POLY OL EFIN DR Y-S HR IN K HEAT S HR IN K TUB IN G (TYPE HSTT)
IN 6" (152.4mm) LE NGTH S
2:1 SH R INK RA TIO
AMS-DTL-23053/5
CL ASS 1 & 2
(Except Clear)
42 EAC H
HSTT06 1/16" (1.6mm) I.D.
- 7 C OLOR S
HSTT12 1/8" (3.2mm) I.D.
- 7 C OLOR S
28 EAC H
HSTT19 3/16" (4.8mm) I.D.
- 7 C OLOR S
21 EAC H
HSTT25 1/4" (6.4mm) I.D.
- 7 C OLOR S
14 EAC H
HSTT38 3/8" (9.5mm) I.D.
- 7 C OLOR S
(Except Clear)
7 E ACH
HSTT50 1/2" (12.7mm) I.D.
- 7 C OLOR S
HSTT75 3/4" (19.0mm) I.D.
- 7 C OLOR S
HSTT100 1" (25.4mm) I.D.
-7 C OLOR S
Note: Colors include: Red, Yellow, Green, Blue, White, Clear and Black
K-HSTTA Contents
For Damp Locations
ADH ES IVE LIN ED BL ACK POLYOL EFIN DA MP-SH R IN K ™ HEA T S H RIN K TU BING (TYP E HSTTA)
IN 6" (152.4mm) LEN GTHS
3:1 SH R IN K RA TIO
AMS-DTL-23053/4
CLA SS 3
24 EAC H
14 EAC H
HSTTA19 3/16" (4.8mm) I.D. HSTTA38 3/8" (9.5mm) I.D.
20 EAC H
10 EAC H
HSTTA25 1/4" (6.4mm) I.D. HSTTA50 1/2" (12.7mm) I.D.
Order number of kits required.
26
6 EA CH
HSTTA75 3/4" (19.0mm) I.D.
4 EA CH
HSTTA100 1" (25.4mm) I.D.
2 EA CH
HSTTA150 1 1/2" (38.1mm) I.D.
Heat Shrink Tools and Accessories
Bonus!
Mica insulation in the
heat element provides
extended life to HSG
Heat Tools.
HSG Heat tool with stand
Heat Reflector Accessory slips
onto heat tools
Heat Tools
Listed 826N
(Heat Tools only)
Part
Number
(Heat Tools
only)
Description
Std.
Pkg.
Qty
HSG-115V-650 • High temperature tool — For use on PANDUIT HSTT,
HSTTF, HSTTR, HSTTK, HSTTRA, HST and HSEC
• Air intake regulator var ies temperature from 650°F (344°C)
to 900°F (482°C) 115 Volt, 10 AMP
• Neoprene jacketed cord with molded strain relief
• Adjustable stand included
• Replaceable bearings, brushes and heating elements
1
HSG-115V-500 • General pur pose tool — For use on all types of heat shr ink
except PANDUIT HSTTT, HSTTF and HSTTK
• Air intake regulator var ies temperature from 500°F (260°C)
to 650°F (344°C) 115 Volt, 8 AMP
• Neoprene jacketed cord with molded strain relief
• Adjustable stand included
• Replaceable bearings, brushes and heating elements
1
HSG-115V-300 • Low temperature tool — For use on small sizes of heat
shrink when heat sensitive items are under or near the
heat shrink tube
• Air intake regulator var ies temperature from 300°F (145°C)
to 450°F (232°C) 115 Volt, 6 AMP
• Neoprene jacketed cord with molded strain relief
• Adjustable stand included
• Replaceable bearings, brushes and heating elements
1
Accessories
Part
Number
HSG-A1
Heat Concentrator Accessory
directs heat to reduce shrink time
Description
• Shrink tube reflector for tubing up to 3/4" inside diameter
• Directs heat around the tubing to reduce shrink time
Std.
Pkg.
Qty
1
HSG-A2
• Shrink tube reflector for tubing up to 1 1/2" inside diameter
• Directs heat around the tubing to reduce shrink time
1
HSG-A3
• Shrink tube concentrator
• Directs heat toward tubing and away from heat
sensitive items
1
HSG-A4
• Black polyethylene carrying case
• Stores heat tool, stand and all three accessories
1
DCT
• Cutting tool for use with HST Thick Wall Heat Shrink
Tubing only
1
Replacement Parts
DCT — Cutting Tool
Carrying Case
Part
Number
HSG-P1
HSG-P2
HSG-P3
HSG-P4
HSG-P5
HSG-P6
HSG-P7
•
•
•
•
•
•
•
Description
Br ush/Spring Kit
Switch 20 Amp
Bear ing Kit
Heat Element 300°F
Heat Element 500°F
Thermo Cut-off switch for HSG-115V-300
Heat Element 650°F
Std.
Pkg.
Qty
1
1
1
1
1
1
1
Order number of heat tools, accessories and replacement parts required.
27
PANDUIT ® DRY -S HRINK ™, DAMP-SHRINK ™ and WET-SHRINK ™ Heat Shrink Tubing
Technical Data
Heat Shrink Process Defined
Extrusion/Material
Various thermoplastic materials that will repeatedly melt and flow, such as polyolefin, PVC, etc., are extruded
into tube form. If examined at a molecular level, the material would resemble long thin strands weakly
connected at various points by crystalline structure. If left in this state, the performance of the tube would be
limited to that of the base material.
Cross Linking
Cross-linking creates high strength bonds between the molecular strands, in addition to the crystalline bonds.
This is done with a high voltage or chemical treatment of the material. The cross-link bonds will not break
down with heat; this transforms the material from a thermoplastic to a thermoset material that will not melt
and flow. The result is a material with superior electrical and mechanical proper ties.
Expansion
The cross-linked tube is heated and the crystalline bonds dissolve, however, the cross-link bonds remain.
The tube now is softer and can be expanded. This causes the cross-link bonds to stretch. When cooled
quickly, the crystalline bonds reform, freezing the tube in the expanded size. The tubing has now completed
the manufacturing process.
Recovery
With the proper type and size of tube selected, the tube is placed over the object to be covered. Heat is now
applied. This causes the crystalline bonds to dissolve again and the tube softens. The stretched cross-link
bonds now return to their original length and the tube shrinks to the diameter it had when cross-linked, unless
it encounters an object larger than this diameter. In this case, it conforms tightly to this object.
Extrusion
Cross-Link
Expansion
Heat Shrink Installation Instructions
General Instructions
Position heat shrink over the object to be covered. Using a heat gun, soft yellow flame torch, infrared heat
source or oven, evenly heat the tubing until it has fully recovered and conforms to the object. Use caution not
to char or burn the tubing. See page 24 for the shrink temperature of each type of Panduit tubing.
Special Instructions for HSTTT and HSTTT4X
TFE tubing is the most difficult to shrink due to its high shrink temperature. TFE shrink tubing must be heated
to the gel state 621° F (327° C) to completely recover. This can be recognized when the tubing changes from
milky white to clear color. It can be shrunk with a heat gun or torch, however, it is very difficult to use these
methods since they have a tendency to overheat the tube in one area while other areas remain too cool. The
most reliable way to shrink TFE is in an oven. Position the heat shrink over the object to be covered and place
it in an oven set at 800° F (427° C) until the tubing turns clear. Once clear, remove assembly from oven to
prevent over heating and allow it to cool at room temperature. Do not quench in cold air or water. Large
objects, particularly metal tubing or rods, must be preheated to get a uniform shrink. FEP material, PANDUIT
HSTTF, is easier to shrink and use of a heat gun, torch or oven will yield good results when the tube is heated
to 350° F (177° C).
28
IP (Ingress Protection) as defined by the International Standard
The IEC 529 international standard describes a system for classifying the degrees of protection provided by
the enclosures of electrical equipment and is a recognized standard around the world. An independent test
laboratory has tested PANDUIT’s Heat Shrink Tubing to the IEC 529 standard. The following information
exhibits the IP ratings for Panduit Heat Shrink tubing and how each of the IP ratings relates to the USA.
IP
x
The first characteristic numeral indicates the level of
protection against the ingress of solid foreign objects.
x
Ingress
Protection
The second characteristic numeral indicates the level of
protection against the ingress of water.
1st Characteristic Numeral
2nd Characteristic Numeral
2nd Characteristic Numeral
Ingress
PANDUIT
Protection
Meaning for
Heat Shrink
(IP)
Protection
1st Characteristic Numeral
Ingress
PANDUIT
Protection Meaning for
Heat Shrink
(IP)
Protection
DR Y -SHRINK ™,
DAMP -SHR INK ™ and
WET-SH RINK ™
Against
ingress of
solid object
0
1
2
3
4
5
6
Non-Protected
50mm diameter
12.5mm diameter
2.5mm diameter
1.0mm diameter
Dust Protected
Dust Tight
DR Y-SHR INK ™, Heat Shrink Tubing
DAMP -SHRINK ™ Heat Shrink Tubing
WET-SHRIN K ™ Heat Shrink Tubing
Intended Application Location
Against
ingress of
water
0
1
2
3
4
5
6
7
8
Ingress
Protection
Rating
Non-Protected
Ver tically Dripping
Dripping (15° tilted)
Spraying
Splashing
Jetting
Powerful Jetting
Temporar y Immersion
Continuous Immersion
Description
DRY Locations not nor mally subject
to moisture
Protected against the ingress of dust but not
protected against the ingress of water.
DAMP Locations subjected to moderate
degrees of water and moisture
Protected against the ingress of dust and
protected against the ingress of a power
jet of water.
WET Locations are defined as underground
burial or immersion in water
Protected against the ingress of dust and
protected against the ingress of water to a
depth of 10 meters.
Does not include PANDUIT ® D RY -S HRI NK HSTTT (TEFLON — T FE) or DRY -S HRI NK HSTT F (TEFLON —FEP)
DR Y -SHR INK Heat Shrink has been tested in accordance with EN 60529 paragraph 13.4 thereby providing
PANDUIT © DRY -SH RINK Heat Shrink with an ingress protection rating of IP62.
DAMP -S HR IN K Heat Shrink has been tested in accordance with EN 60529 paragraph 13.4 and with
paragraph 14.2.6 thereby providing PANDUIT DAMP -S HR IN K with an ingress protection rating of IP66.
WET-SH RINK Heat Shrink has been tested in accordance with EN 60529 paragraph 13.4, paragraph 14.2.6
and with paragraph 14.2.7 thereby providing WET -SH RINK Heat Shrink with an ingress protection rating of
IP68. PANDUIT W ET -S HR INK Heat Shrink has passed EN 60529 paragraph 14.2.7 at depth of 10 meters.
29
Heat Shrink Selection Guide
Recommended Tubing Size for Common Wire Types Based on Location
For Insulated Wire, Uninsulated Wire and Insulated Wire With Copper Connectors
Instructions for tube selection:
1) D etermine Location Type.
L OCATION:
D RY—IP62: A location not normally subjec t to dampness or wetness. A location classified as dry may be temporarily subject to dampness or
wetness, as in the case of a building under construction.
DAMP— IP66: Partially protected locations under canopies, marquees, roofed open porches, and like loc ations, and interior locations subjec t
to moderate degrees of m oisture, such as s ome basements, some barns and some c old-storage warehouses.
WET— IP68: Installations underground or in conc rete s labs or masonr y in direct contac t with the earth, and locations subject to saturation w ith
water or other liquids, such as vehicle washing areas, and loc ations exposed to weather and unprotected.
2) Match wire size to location type under required applic ation - insulated wire, uninsulated wire, or insulated wire with copper connectors.
3) R ead corres ponding part number.
4) Par t numbers with "-Y" are packages containing 6" pieces. Part numbers with "-48" are 48" pieces.
5) Par t numbers shown below are for black heat shrink. Cons ult relevant catalog section for color options.
Wire
Insulated Wire
Uninsulated Wire
Insulated Wire with Copper Connector
Size DR Y-S H RIN K™ DAMP -SHR INK ™ WET -SH R IN K™ DR Y-S H RIN K DAM P-S H RIN K WE T -SHR INK
DR Y-SH R IN K DAM P-S HR IN K W ET -SHR IN K
24
HSTT12-Y
HSTTA19-Y
—
—
—
—
HSTT12-Y
—
—
22
HSTT12-Y
HSTTA19-Y
—
—
—
—
HSTT12-Y
—
—
20
HSTT12-Y
HSTTA19-Y
—
HSTT06-Y
—
—
HSTT19-Y
HSTTA19-Y
—
18
HSTT19-Y
HSTTA19-Y
—
HSTT06-Y
—
—
HSTT19-Y
HSTTA19-Y
—
16
HSTT19-Y
HSTTA25-Y
—
HSTT06-Y
—
—
HSTT19-Y
HSTTA25-Y
—
14
HSTT19-Y
HSTTA25-Y
—
HSTT12-Y
HSTTA19-Y
—
HSTT19-Y
HSTTA25-Y
—
12
HSTT25-Y
HSTTA38-Y
HST0.4-48-5
HSTT12-Y
HSTTA19-Y
—
HSTT25-Y
HSTTA38-Y HST0.4-48-5
10
HSTT25-Y
HSTTA38-Y
HST0.4-48-5
HSTT19-Y
HSTTA25-Y
—
HSTT25-Y
HSTTA38-Y HST0.4-48-5
8
HSTT38-Y
HSTTA50-Y
HST0.4-48-5
HSTT25-Y
HSTTA25-Y
—
HSTT38-Y
HSTTA50-Y HST0.4-48-5
6
HSTT50-Y
HSTTA50-Y
HST0.8-48-5
HSTT25-Y
HSTTA38-Y HST0.4-48-5
HSTT50-Y
HSTTA50-Y HST0.8-48-5
4
HSTT50-Y
HSTTA75-Y
HST0.8-48-5
HSTT38-Y
HSTTA38-Y HST0.4-48-5
HSTT50-Y
HSTTA75-Y HST0.8-48-5
3
HSTT50-Y
HSTTA75-Y
HST0.8-48-5
HSTT38-Y
HSTTA50-Y HST0.4-48-5
HSTT50-Y
HSTTA75-Y HST0.8-48-5
2
HSTT75-Y
HSTTA100-Y HST0.8-48-5
HSTT50-Y
HSTTA50-Y HST0.8-48-5
HSTT75-Y
HSTTA100-Y HST0.8-48-5
1
HSTT75-Y
HSTTA100-Y HST0.8-48-5
HSTT50-Y
HSTTA50-Y HST0.8-48-5
HSTT75-Y
HSTTA100-Y HST1.1-48-5
1/0
HSTT75-Y
HSTTA100-Y HST1.1-48-5
HSTT50-Y
HSTTA75-Y HST0.8-48-5
HSTT75-Y
HSTTA100-Y HST1.1-48-5
2/0 HSTT100-Y
HSTTA100-Y HST1.1-48-5
HSTT50-Y
HSTTA75-Y HST0.8-48-5
HSTT100-Y HSTTA100-Y HST1.1-48-5
3/0 HSTT100-Y
HSTTA150-Y HST1.1-48-5
HSTT75-Y
HSTTA100-Y HST0.8-48-5
HSTT100-Y HSTTA150-Y HST1.5-48-5
4/0 HSTT100-Y
HSTTA150-Y HST1.5-48-5
HSTT75-Y
HSTTA100-Y HST1.1-48-5
HSTT100-Y HSTTA150-Y HST1.5-48-5
250 HSTT100-Y
HSTTA150-Y HST1.5-48-5 HSTT100-Y HSTTA100-Y HST1.1-48-5
HSTT100-Y HSTTA150-Y HST1.5-48-5
300 HSTT150-48-5 HSTTA150-Y HST1.5-48-5 HSTT100-Y HSTTA100-Y HST1.1-48-5
HSTT150-Y HSTTA150-Y HST1.5-48-5
350 HSTT150-48-5 HSTTA150-Y HST1.5-48-5 HSTT100-Y HSTTA150-Y HST1.5-48-5 HSTT150-48-5 HSTTA150-Y HST2.0-48-2
400 HSTT150-48-5 HSTTA150-Y HST2.0-48-2 HSTT100-Y HSTTA150-Y HST1.5-48-5 HSTT150-48-5 HSTTA150-Y HST2.0-48-2
500 HSTT150-48-5 HSTTA150-Y HST2.0-48-2 HSTT100-Y HSTTA150-Y HST1.5-48-5 HSTT150-48-5 HSTTA150-Y HST2.0-48-2
600 HSTT150-48-5 HSTTA150-Y HST2.0-48-2 HSTT150-48-5 HSTTA150-Y HST2.0-48-2 HSTT150-48-5 HSTTA150-Y HST2.0-48-2
700 HSTT200-48-5 HSTTA150-Y HST2.0-48-2 HSTT150-48-5 HSTTA150-Y HST2.0-48-2 HSTT200-48-5
—
HST2.0-48-2
750 HSTT200-48-5 HSTTA150-Y HST3.0-48-2 HSTT150-48-5 HSTTA150-Y HST2.0-48-2 HSTT200-48-5
—
HST3.0-48-2
800 HSTT200-48-5
—
HST3.0-48-2 HSTT150-48-5 HSTTA150-Y HST2.0-48-2 HSTT200-48-5
—
HST3.0-48-2
900 HSTT200-48-5
—
HST3.0-48-2 HSTT150-48-5 HSTTA150-Y HST2.0-48-2 HSTT200-48-5
—
HST3.0-48-2
1000 HSTT200-48-5
—
HST3.0-48-2 HSTT200-48-5 HSTTA150-Y HST2.0-48-2 HSTT200-48-5
—
HST3.0-48-2
1250 HSTT300-48-2
—
HST3.0-48-2 HSTT200-48-5 HSTTA150-Y HST2.0-48-2
—
—
HST3.0-48-2
1500 HSTT300-48-2
—
HST3.0-48-2 HSTT200-48-5
—
HST3.0-48-2
—
—
—
1750 HSTT300-48-2
—
HST3.0-48-2 HSTT200-48-5
—
HST3.0-48-2
—
—
—
2000 HSTT300-48-2
—
HST3.0-48-2 HSTT200-48-5
—
HST3.0-48-2
—
—
—
Sizing information is based on the following wire types: MTW, THHN, THWN, TFN, THW, TW, TF, RHW, RH, RHH AND UL1015.
THHN is the most common wire type.
Portions reprinted with permission from NFPA, the National Electrical Code ® Handbook, Copyright@ 1996, National Fire Protection Association,
Quincy, MA 02269.
All rights reserved. National Electrical Code ® and NEC ® are registered trademarks of the National Fire Protection Association, Inc., Quincy, MA 02269.
30
Size Selection for Heat Shrink Tubing
Size Selection for Heat Shrink Tubing
Generally, the largest tube that shrinks down tightly onto an object should be chosen. This allows the heat
shrink tubing maximum stress relief and this will yield the longest service life.
Example:
A multiconductor cable needs to be covered with HSTT Type DR Y -SHR INK ™ Heat Shrink. The area to be
covered has a measured outside diameter of .700" (17.8mm). The two possibilities are HSTT75-48-5 and
HSTT100-48-5.
Part Number
HSTT75-48-5
HSTT100-48-5
Expanded I.D.
In. (mm)
Recovered I.D.
In. (mm)
.750" (19.0)
1.00" (25.4)
.375" (9.5)
.500" (12.7)
The proper choice is HSTT100-48-5 since the tube will recover more than HSTT75-48-5. The HSTT75-48-5
will fit over the .700" (17.8mm) outside diameter; however, this is not the proper choice since it is smaller than
the HSTT100-48-5. In general, heat shrink should recover at least 10-20% to reduce stress and yield the
longest service life.
Thick Wall Heat Shrink and Power Connector Selection Guide
Panduit thick wall heat shrink tubing, HST, provides excellent insulation, abrasion protection and strain relief
for Panduit’s lugs and splices. The HST, with internal hot melt adhesive, is UL Listed per UL486D and CSA
Certified for direct burial. It is suitable for outdoor use and wet locations. The following charts on page 32 have
been designed to assist in the selection of the correct thick wall heat shrink for a specific lug or splice size.
31
PANDUIT ® WET -SHRINK ™ Thick Wall Heat Shrink and Power Connector Selection Guide
Lugs
Standard Barrel Copper
Long Barrel Copper
Lug Part
Numb ers
# of
Ho les
Heat Shrink
Part Numb ers
Lug Part
Numbers
LCA8
LCA6
LCA4
LCA2
LCA1
LCA1/0
LCA2/0
LCA3/0
LCA4/0
LCA250
LCA300
LCA350
LCA400
LCA500
LCA600
LCD8
LCD6
LCD4
LCD2
LCD1
LCD1/0
LCD2/0
LCD3/0
LCD4/0
LCD250
LCD300
LCD350
LCD400
LCD500
LCD600
LCD750
LCD1000
NONE OR 1
NONE OR 1
NONE OR 1
NONE OR 1
NONE OR 1
NONE OR 1
NONE OR 1
NONE OR 1
NONE OR 1
NONE OR 1
1
1
1
1
1
2
2
2
2
2
NONE OR 2
NONE OR 2
NONE OR 2
NONE OR 2
NONE OR 2
NONE OR 2
NONE OR 2
NONE OR 2
NONE OR 2
NONE OR 2
NONE OR 2
NONE OR 2
HST0.4-3-Q
HST0.8-6-X
HST0.8-6-X
HST0.8-6-X
HST1.1-6-X
HST1.1-6-X
HST1.1-6-X
HST1.5-9-X
HST1.5-9-X
HST1.5-9-X
HST1.5-9-X
HST2.0-9-5
HST2.0-9-5
HST2.0-9-5
HST2.0-9-5
HST0.4-3-Q
HST0.8-6-X
HST0.8-6-X
HST0.8-6-X
HST1.1-6-X
HST1.1-6-X
HST1.1-6-X
HST1.5-9-X
HST1.5-9-X
HST1.5-9-X
HST1.5-9-X
HST2.0-9-5
HST2.0-9-5
HST2.0-9-5
HST2.0-9-5
HST3.0-12-2
HST3.0-12-2
LCB8
LCB6
LCB4
LCB2
LCB1
LCB1/0
LCB2/0
LCB3/0
LCB4/0
LCB250
LCB300
LCB350
LCB400
LCB500
LCB600
LCB750
LCB800
LCB1000
LCC8
LCC6
LCC4
LCC2
LCC1
LCC1/0
LCC2/0
LCC3/0
LCC4/0
LCC250
LCC300
LCC350
LCC400
LCC500
LCC600
LCC750
LCC800
LCC1000
# of
Holes
Heat Sh rink
Part Numbers
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
NON E OR
NON E OR
NON E OR
NON E OR
NON E OR
NON E OR
NON E OR
NON E OR
NON E OR
NON E OR
NON E OR
NON E OR
NON E OR
NON E OR
NON E OR
NON E OR
2
NON E OR
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Short Barrel Copper
Lug Part
Numb ers
# of
Heat Sh rin k
Holes Part Numbers
Aluminum Lugs
Lu g Part
Num bers
# of
Heat Shrink
Holes Part Numbers
HST0.4-3-Q
LCAS8
1
HST0.4-3-Q
LAA6
1
HST0.8-6-X
HST0.8-6-X
LCAS6
1
HST0.8-6-X
LAA4
1
HST0.8-6-X
HST0.8-6-X
LCAS4
1
HST0.8-6-X
LAA2
1
HST0.8-6-X
HST0.8-6-X
LCAS2
1
HST0.8-6-X
LAA1
1
HST1.1-6-X
HST1.1-6-X
LCAS1
1
HST1.1-6-X
LCA1
1
HST1.1-6-X
HST1.1-6-X
LCAS1/0
1
HST1.1-6-X
LAA1/0
1
HST1.1-6-X
HST1.1-6-X
LCAS2/0
1
HST1.1-6-X
LAA2/0
1
HST1.1-6-X
HST1.5-9-X
LCAS3/0
1
HST1.5-9-X
LAA3/0
1
HST1.5-9-X
HST1.5-9-X
LCAS4/0
1
HST1.5-9-X
LAA4/0
1
HST1.5-9-X
1
HST1.5-9-X
LCAS250
HST1.5-9-X
LAA250
1
HST1.5-9-X
HST1.5-9-X
LAA300
1
HST1.5-9-X
HST2.0-9-5
LAA350
1
HST2.0-9-5
HST2.0-9-5
LAA400
1
HST2.0-9-5
HST2.0-9-5
LAA500
1
HST2.0-9-5
HST2.0-9-5
LAA750
1
HST3.0-12-2
HST3.0-12-2
LAA1000
1
HST3.0-12-2
HST3.0-12-2
LAB1/0
2
HST1.1-6-X
HST3.0-12-2
LAB2/0
2
HST1.1-6-X
HST0.4-3-Q
LAB3/0
2
HST1.5-9-X
HST0.8-6-X
LAB4/0
2
HST1.5-9-X
HST0.8-6-X
LAB250
2
HST1.5-9-X
HST0.8-6-X
LAB300
2
HST1.5-9-X
HST0.8-6-X
LAB350
2
HST2.0-9-5
HST1.1-6-X
LAB400
2
HST2.0-9-5
HST1.1-6-X
LAB500
2
HST2.0-9-5
HST1.5-9-X
LAB600
2
HST2.0-9-5
HST1.5-9-X
LAB750
2
HST3.0-12-2
HST1.5-9-X
LAB800
2
HST3.0-12-2
HST1.5-9-X
LAB1000
2
HST3.0-12-2
HST2.0-9-5
HST2.0-9-5
HST2.0-9-5
HST2.0-9-5
Lug Notes:
HST3.0-12-2
Heat Shrink tubing selected should cover the lug barrel and a minimum
HST3.0-12-2 of 1 1/2" (2" on tubing size 1.5" and higher) of cable insulation.
HST3.0-12-2 Shrink tubing at lug end first and continue toward cable end.
Splices
Standard Barrel Copper
Splice
Part Numb ers
SCS8
SCS6
SCS4
SCS2
SCS1
SCS1/0
SCS2/0
SCS3/0
SCS4/0
SCS250
SCS300
SCS350
SCS400
SCS500
SCS600
SCS750
SCS1000
Heat Shrink
Part Num bers
HST0.4-6-X
HST0.8-6-X
HST0.8-6-X
HST0.8-6-X
HST1.1-6-X
HST1.1-6-X
HST1.1-6-X
HST1.5-9-X
HST1.5-9-X
HST1.5-9-X
HST1.5-9-X
HST2.0-9-5
HST2.0-9-5
HST2.0-9-5
HST2.0-9-5
HST3.0-12-2
HST3.0-12-2
Long Barrel Copper
Sp lice
Part Numbers
SCL8
SCL6
SCL4
SCL2
SCL1
SCL1/0
SCL2/0
SCL3/0
SCL4/0
SCL250
SCL300
SCL350
SCL400
SCL500
SCL600
SCL750
SCL1000
Heat Shrink
Part Numb ers
HST0.4-6-X
HST0.8-6-X
HST0.8-6-X
HST0.8-6-X
HST1.1-6-X
HST1.1-6-X
HST1.1-6-X
HST1.5-9-X
HST1.5-9-X
HST1.5-9-X
HST1.5-9-X
HST2.0-9-5
HST2.0-9-5
HST2.0-9-5
HST2.0-9-5
HST3.0-12-2
HST3.0-12-2
Short Barrel Copper
Splice
Part Numb ers
SCSS8
SCSS6
SCSS4
SCSS2
SCSS1
SCSS1/0
SCSS2/0
SCSS3/0
SCSS4/0
SCSS250
Heat Sh rin k
Part Numbers
HST0.4-6-X
HST0.8-6-X
HST0.8-6-X
HST0.8-6-X
HST1.1-6-X
HST1.1-6-X
HST1.1-6-X
HST1.5-9-X
HST1.5-9-X
HST1.5-9-X
Aluminum Long Barrel
Splice
Part Numb ers
SA6
SA4
SA2
SA1
SA1/0
SA2/0
SA3/0
SA4/0
SA250
SA300
SA350
SA400
SA500
SA600
SA750
SA800
SA1000
Heat Sh rin k
Part Numbers
HST0.8-6-X
HST0.8-6-X
HST0.8-6-X
HST1.1-6-X
HST1.1-6-X
HST1.1-6-X
HST1.5-9-X
HST1.5-9-X
HST1.5-9-X
HST1.5-9-X
HST2.0-9-5
HST2.0-9-5
HST2.0-9-5
HST2.0-9-5
HST3.0-12-2
HST3.0-12-2
HST3.0-12-2
Splice Notes:
Heat Shrink tubing selected should cover the splice barrel and a minimum of 1 1/2" (2" on tubing size 1.5" and higher) of cable insulation on each side of the splice.
Shrink tubing at the center of the splice first, continue toward one cable end and then the other.
Power connector part no. is prefix which indicates lug type and cable size, see Power Connector Catalog (SA101N15C-NL) for complete part numbers.
32
PANDUIT ® DRY -SHRINK ™, DAMP-S HRINK
(Cross-linked)
HSTTV
HIGHLY FLEXIBLE
POLYOLEFIN
(Cross-linked)
HSTTR
SEMI-RIGID
POLYOLEFIN
(Cross-linked)
HSTTVA
DUAL WALL
POLYOLEFIN
(Cross-linked)
HSTTRA
DUAL WALL
POLYOLEFIN
(Cross-linked)
HSTTA
DUAL WALL
POLYOLEFIN
(Cross-linked)
HST
Key
Characteristics
Standard Sizes
Expanded I.D.
Flexible Heat Shrink Tubing.
Flame retardant.
Class 2 (Clear) is not
flame retardant.
3/64" to 4"
(1.2 to 101.6mm)
Material
FLEXIBLE
POLYOLEFIN
HEAVY-WALL
DUAL WALL
POLYOLEFIN
(Cross-linked)
Highly flexible heat shrink
tubing, highly flame retardant,
VW-1 rated. Fast shrink time.
Semi-rigid.
High strength.
Flame retardant.
HSTTT
FLUOROPLASTIC
TEFLON (TFE) –
Polytetrafluorethylene
HSTTT4X FLUOROPLASTIC
TEFLON (TFE) –
Polytetrafluorethylene
HSTTF
FLUOROPLASTIC
TEFLON (FEP) –
F luorinated Ethylene
Propylene
Standard
Colors
Packaging
AMS-DTL-23053/5
Black
6" pcs.
Class 1
Clear
4' lengths,
(black & colors)
White
25' to
Class 2 (Clear)
Red
1000' reels
UL Recognized
Yellow
depending on
(except clear).
Blue
diameter
CSA Certified
Green
1/2" and 1" cut
(except clear).
Yellow/Green
pieces
3/32" to 1 1/2" UL (VW-1) Recognized
Black
4' lengths
(2.4 to 38.1mm)
CSA Certified
Red
100' to
AMS-DTL-23053/5
Yellow
1000' reels
Class 3
Blue
depending on
White
diameter
3/64" to 1"
AMS-DTL-23053/6
Black
4' lengths
(1.2 to 25.4mm)
Class 1 (Black)
Black
6" pcs.
4' lengths
Adhesive lined, flexible, flame
retardant outer thin wall
tubing. High shrink ratio.
1/8" to 1"
(3.2 to 25.4mm)
AMS-DTL-23053/4
Class 1
Black
4' lengths
Adhesive lined, flexible, flame
retardant outer thin wall
tubing. High shrink ratio.
3/16" to 1 1/2"
(4.8 to 38.1mm)
AMS-DTL-23053/4
Class 3
Black
6" pcs.
4' lengths
0.4" to 3.0"
(10.1 to 76.2mm)
AMS-DTL-23053/15
UL Listed
CSA Certified
Black
Red
3" pcs.
6" pcs.
9" pcs.
12" pcs.
4' lengths
25' to
1000' reels
depending on
diameter
25' and 100'
Reels
Excellent environmental
protection, for use either
above or below ground.
Encapsulating inner wall.
ELASTOMER
NEOPRENE
(Cross-linked)
Applicable
Specifications
AMS-DTL-23053/4
Class 2
HSTTN
FLUOROPLASTIC
KYNAR
Heat Shrink Tubing
1/8" to 1 1/2"
(3.2 to 38.1mm)
POLYVINYLCHLORIDE – Flexible, highly flame
PVC
retardant tubing. Resistant
(Cross-linked/Heat
to most fuels and oils.
Shrinkable)
HSTTK
™
Adhesive lined, flexible,
flame retardant outer wall
thin wall tubing.
HSTTP
(Cross-linked)
and WET-SHRINK
Technical Data
General Information
Product
Type
HSTT
™
Highly flexible, highly abrasion
resistant, heavy duty, tough
tubing. Highly flame retardant
material. Extended operating
temperature.
Excellent abrasion and
chemical resistance, highly
flame retardant, semi-rigid,
transparent insulation.
3/64" to 2"
UL(VW-1) Recognized
(1.2 to 50.8mm)
CSA Certified
1/4" to 3"
(6.4mm to
76.2mm)
AMS-DTL-23053/1
Class 2
Meets VW-1
3/64" to 1"
AMS-DTL-23053/8
(1.2 to 25.4mm) UL (VW-1) Recognized
Black
Black
Clear
4' lengths
Highly heat resistant, highly
chemical resistant, widest
temperature range of any
plastic material. Excellent
outdoor exposure. A low
coefficient of friction.
30 to 0 AWG and
9/16" to 1 1/2"
(0.9 to 38.1mm)
AMS-DTL-23053/12
Class 3
Milky Clear
4' lengths
Highly heat resistant, highly
chemical resistant, widest
temperature range of any
plastic material. Excellent
outdoor exposure. A low
coefficient of friction.
High shrink ratio.
5/64" to 1 1/4"
(2.0 to 31.8mm)
AMS-DTL-23053/12
Class 5
Milky Clear
4' lengths
Same as HSTTT
characteristics plus it
has lower shrink
temperature.
24 to 0AWG and
1/2" to 2"
(0.8 to 50.8mm)
AMS-DTL-25053/11
Class 1
Clear
4' lengths
KYNAR is a registered trademark of ELF Atochem
TEFLON is a registered trademark of E.I. DuPont Co.
33
PANDUIT ® D RY-SHRINK ™ , DAMP -S HRINK
™
and WET-SHRINK ™ Heat Shrink Tubing
Technical Data
General Information
Product
Type
Material
Shrink
Temp.
Shrink
Ratio Longitudinal
‡
Shrinkage
Typical Applications
248°F
(120°C)
2:1
+5%
-5%
Economical and easy way to insulate, protect,
harness and identify electrical and electronic
components in a wide variety of applications.
Black is U.V. Resistant.
HSTTV
HIGHLY FLEXIBLE -67°F (-55° C)
POLYOLEFIN
to
(Cross-linked)
257°F (125°C)
185°F
(85°C)
2:1
+1%
-10%
Use where UL recognition with VW-1 rating is 11-13
required. Use where the wire component
cannot tolerate higher shrink temperatures,
reduces application time to insulate, protect,
identify, etc. Black is U.V. Resistant.
HSTTR
SEMI-RIGID
POLYOLEFIN
-67°F (-55° C)
to
275°F (135°C)
275°F
(135° C)
2:1
+5%
-5%
Strain relief and insulation of soldered or
crimped connections when protection is
needed, tough covering for delicate
components, capacitor covers, diodes and
resistors. Black is U.V. Resistant.
14
DUAL WALL
POLYOLEFIN
-67°F (-55° C)
to
230°F (110°C)
250°F
(121°C)
2:1
+1%
-5%
Seals and protects components from
moisture and corrosion. Use where a flexible
tubing is needed. Suitable for damp locations.
20
DUAL WALL
POLYOLEFIN
-67°F (-55° C)
to
230°F (110°C)
392°F
(200°C)
2.5:1
+1%
-10%
Environmentally seals and protects
components forming a rugged and heavy duty
covering. The 2.5:1 shrink ratio is a benefit
when working with connector to cable
transitions. Encapsulated components.
Suitable for damp locations.
22
DUAL WALL
POLYOLEFIN
-67°F (-55° C)
to
230°F (110°C)
250°F
(121°C)
3:1
+1%
-15%
Environmentally seals and protects
components. The 3:1 shrink ratio is a benefit
when working with connector to cable
transitions. Encapsulated components.
Suitable for damp locations.
21
HEAVY-WALL
DUAL WALL
POLYOLEFIN
-85°F (-65° C)
to
230°F (110°C)
250°F
(121°C)
3:1
+1%
-10%
Seals and protects electrical connections and
splices above or below ground, 3:1 shrink
ratio. Suitable for outdoor and wet locations.
23
POLYVINYL
CHLORIDE – PVC
-4°F (-20°C)
to
221°F (105°C)
250°F
(121°C)
2:1
+1%
-20%
Ripple free conformance around sharp bends
as in appliance handles and bus bars. Good
cut through and solder-iron resistance.
Black is U.V. Resistant.
15
ELASTOMER
NEOPRENE
-94°F (-70° C)
to
250°F (121°C)
275°F
(135°C)
2:1
+1%
-10%
Insulation and abrasion resistance, extensive
military uses on vehicles and ship-board.
Excellent chemical resistant especially to
fuels and oils. Black is U.V. Resistant.
16
HSTTK
FLUOROPLASTIC -67°F (-55° C)
to
KYNAR
(Cross-linked)
347°F (175°C)
350°F
(176°C)
2:1
+10%
-10%
Protection and strain relief for wires or
connectors in a high temperature or solvent
rich environment. Insulation of heater leads.
19
HSTTT
FLUOROPLASTIC -88°F (-67° C)
TEFLON (TFE) –
to
Polytetrafluorethylene
482°F (250°C)
625°F
(329°C).
See
instructions
on page 29
2:1
+20%
-20%
High insulation and abrasion resistance. High
temperature, strain relief, resists corrosive
atmospheres, self lubrication and nonwetting. Can be used with fiber optics and as
a strain relief for high density connectors.
U.V. Resistant
17
HSTTT4X FLUOROPLASTIC -88°F (-67° C)
625°F
(329°C).
See
instructions
on page 29
4:1
+20%
-20%
High insulation and abrasion resistance. High
temperature, strain relief, resists corrosive
atmospheres, self lubrication and nonwetting. Can be used with fiber optics and as
a strain relief for high density connectors.
U.V. Resistant
17
350°F
(176°C)
1.3:1
+15%
-15%
All the advantages of TFE tubing plus the
advantage of a lower shrink temperature. Can
be used with fiber optics and as a strain relief
for high density connectors.
U.V. Resistant
18
(Cross-linked)
(Cross-linked)
HSTTVA
(Cross-linked)
HSTTRA
(Cross-linked)
HSTTA
(Cross-linked)
HST
(Cross-linked)
HSTTP
(Cross-linked/Heat
Shrinkable)
HSTTN
(Cross-linked)
TEFLON
(TFE) –
to
Polytetrafluorethylene 482°F (250°C)
HSTTF
FLUOROPLASTIC -88°F (-67° C)
TEFLON (FEP) –
to
Fluorinated Ethylene
392°F (200°C)
Propylene
‡ Dimensions are approximate. Refer to the ordering information for exact Minimum Expanded and Maximum Recovered I.D
34
Page
No.
-67°F (-55° C)
to
275°F (135°C)
HSTT
FLEXIBLE
POLYOLEFIN
Operating
Temperature
Range
KYNAR is a registered trademark of ELF Atochem
T EF LON is a registered trademark of E.I. DuPont Co.
4-10
PANDUIT ® D RY-SHRINK ™ , DAMP -S HRINK
™
and WET-SHRINK ™ Heat Shrink Tubing
Technical Data
Specifications/Test Methods for PANDUIT Heat Shrink Tubing
Product
Type
Low
Temperature
Flexibility
Tensile
Strength
Ultimate
Elongation
Heat
Aging
Heat
Shock
1500 P.S.I.
(10.3 MPa) MIN.
ASTM D638
200% (MIN.)
ASTM D638
175°C/168 hrs.
100% MIN.
Elongation
-55°C/4 hrs.
No cracking
1500 P.S.I.
(10.3 MPa) MIN.
ASTM D638
200% (MIN.)
ASTM D638
150°C/168 hrs.
100% MIN.
Elongation
2000 P.S.I.
(13.8 MPa) MIN.
ASTM D638
200% (MIN.)
ASTM D638
175°C/168 hrs.
100% MIN.
Elongation
1500 P.S.I.
(10.3 MPa) MIN.
ASTM D638
200% (MIN.)
ASTM D638
1500 P.S.I.
(10.3 MPa) MIN.
ASTM D638
200% (MIN.)
ASTM D638
1300 P.S.I.
(9.0 MPa) MIN.
ASTM D638
250% (MIN.)
ASTM D638
1200 P.S.I.
(8.3 MPa) MIN.
ASTM D638
200% (MIN.)
ASTM D638
175°C/168 hrs.
No dripping
No flowing
No cracking
175°C/168 hrs.
No dripping
No flowing
No cracking
175°C/168 hrs.
No dripping
No flowing
No cracking
175°C/168 hrs.
100% MIN.
Elongation
2000 P.S.I.
(13.8 MPa) MIN.
ASTM D638
200% (MIN.)
ASTM D638
135°C/168 hrs.
130% MIN
Elongation
250°C/4 hrs.
No dripping,
No flowing,
No cracking
250°C/4 hrs.
No dripping,
No flowing,
No cracking
250°C/4 hrs.
No dripping,
No flowing,
No cracking
250°C/4 hrs.
No dripping,
No flowing,
No cracking
250°C/4 hrs.
No dripping,
No flowing,
No cracking
250°C/4 hrs.
No dripping,
No flowing,
No cracking
225°C/4 hrs.
No dripping,
No flowing,
No cracking
200°C/4 hrs.
No dripping,
No flowing,
No cracking
225% (MIN.)
ASTM D412
121°C/168 hrs.
175% MIN.
Elongation
-70°C/4 hrs.
No cracking
HSTTK
FLUOROPLASTIC
KYNAR
(Cross-linked)
5000 P.S.I.
(34.5 MPa) MIN.
ASTM D638
150% (MIN.)
ASTM D638
250°C/168 hrs.
50% MIN.
Elongation
-55°C/4 hrs.
No cracking
HSTTT
FLUOROPLASTIC
TEFLON (TFE) –
2500 P.S.I.
(17.3 MPa) MIN.
ASTM D638
200% (MIN.)
ASTM D638
350°C/96 hrs.
200% MIN.
Elongation
120,000 P.S.I
(690 MPa)
MIN.
ASTM D882
N/A
2500 P.S.I.
(17.3 MPa) MIN.
ASTM D638
200% (MIN.)
ASTM D638
350°C/96 hrs.
200% MIN.
Elongation
2000 P.S.I.
(13.8 MPa) MIN.
ASTM D638
200% (MIN.)
ASTM D638
250°C/96 hrs.
200% MIN.
Elongation
200°C/4 hrs.
No dripping,
No flowing,
No cracking
300°C/4 hrs.
No dripping,
No flowing,
No cracking
400°C/4 hrs.
No dripping,
No flowing,
No cracking
400°C/4 hrs.
No dripping,
No flowing,
No cracking
N/A
N/A
(C ross-linked)
1500 P.S.I.
(10.3 MPa) MIN.
ASTM D412
HSTT
Material
FLEXIBLE
POLYOLEFIN
(C ross-linked)
HSTTV
HIGHLY FLEXIBLE
POLYOLEFIN
(C ross-linked)
HSTTR
SEMI-RIGID
POLYOLEFIN
(C ross-linked)
HSTTVA
DUAL WALL
POLYOLEFIN
(C ross-linked)
HSTTRA
DUAL WALL
POLYOLEFIN
(C ross-linked)
HSTTA
DUAL WALL
POLYOLEFIN
(C ross-linked)
HST
HEAVY-WALL DUAL
WALL POLYOLEFIN
(C ross-linked)
HSTTP
POLYVINYLCHLORIDE –
PVC
(C ross-linked/Heat
Shrinkable)
HSTTN
ELASTOMER
NEOPRENE
Polytetrafluorethylene
HSTTT4X FLUOROPLASTIC
TEFLON
(TFE) –
Polytetrafluorethylene
HSTTF
FLUOROPLASTIC
TEFLON (FEP) –
Fluorinated Ethylene
Propylene
KYNAR is a registered trademark of ELF Atochem
-25°C/4 hrs.
No cracking
-55°C/4 hrs.
No cracking
N/A
N/A
N/A
-55°C/4 hrs.
No cracking
No cracking
ASTM 746
-65°C/4 hrs.
No cracking
Secant
Modulus
25,000 P.S.I.
(172.4 MPa)
MAX.
ASTM D882
25,000 P.S.I.
(172.4 MPa)
MAX.
ASTM D882
25,000 P.S.I.
(172.4 MPa)
MIN.
ASTM D882
25,000 P.S.I.
(172.4 MPa)
MAX.
ASTM D882
25,000 P.S.I.
(172.4 MPa)
MIN.
ASTM D882
25,000 P.S.I.
(172.4 MPa)
MAX.
ASTM D882
25,000 P.S.I.
(172.4 MPa)
MAX.
ASTM D882
25,000 P.S.I.
(172.4 MPa)
MAX.
ASTM D882
-65°C/4 hrs.
No cracking
N/A
-65°C/4 hrs.
No cracking
N/A
TEFLON is a registered trademark of E.I. DuPont Co.
35
PANDUIT ® DRY-SHRINK ™ , DAMP -SHRINK ™ and WET-SHRINK ™ Heat Shrink Tubing
Technical Data
Specifications/Test Methods for PANDUIT Heat Shrink Tubing
Produ ct
Type
Material
Sp ecific
Gravity
Flamm ab ility
Water
Absorption
Fluid
Resistan ce
101 4 MIN.
ASTM
D876
500 V/MIL.
(19.7 Kv/mm) MIN.
ASTM D2671
11-13
101 4 MIN.
ASTM
D876
500 V/MIL.
(19.7 Kv/mm) MIN.
ASTM D2671
14
101 2 MIN.
ASTM
D876
500 V/MIL.
(19.7 Kv/mm) MIN.
ASTM D2671
20
101 5 MIN.
ASTM
D876
500 V/MIL.
(19.7 Kv/mm) min.
ASTM D2671
22
101 2 MIN.
ASTM
D876
300 V/MIL.
(11.8 Kv/mm) MIN.
ASTM D2671
21
101 3 MIN.
ASTM
D876
200 V/MIL.
(7.9 Kv/mm) MIN.
ASTM D2671
23
101 1 MIN.
ASTM
D876
400 V/MIL.
(15.8 Kv/mm) MIN.
ASTM D2671
15
175°C/
Self
0.5% MAX. Tensile Strength 1000
16 hrs. Extinguishing
ASTM
P.S.I. MIN. (6.9MPa)
No
ASTM D2671
D570
Dielectric Strength
corrosion Procedure C
400 V/MIL MIN. (15.8
Kv/mm)
SEMI-RIGID
1.35
150°C/
Self
0.5% MAX. Tensile Strength 1600
POLYOLEFIN
ASTM
16 hrs. Extinguishing
ASTM
P.S.I. MIN. (11.1MPa)
(Cross-linked)
D792
No
ASTM D2671
D570
Dielectric Strength
corrosion Procedure B
400 V/MIL MIN.
(15.8 Kv/mm)
DUAL WALL
N/A
121°C/
Self
0.5% MAX. Tensile Strength 1000
POLYOLEFIN
16 hrs. Extinguishing
ASTM
P.S.I. MIN. (6.9 MPa)
(Cross-linked)
No
ASTM D2671
D570
Dielectric Strength
corrosion Procedure B
400 V/MIL MIN.
(15.8 Kv/mm)
DUAL WALL
N/A
121°C/
N/A
0.5% MAX. Tensile Strength 1000
POLYOLEFIN
16 hrs.
ASTM
P.S.I. MIN. (6.9 MPa)
(Cross-linked)
No
D570
Dielectric Strength
corrosion
400 V/MIL MIN.
(15.8 Kv/mm)
DUAL WALL
N/A
121°C/
Self
1.0% MAX. Tensile Strength 900
POLYOLEFIN
16 hrs. Extinguishing
ASTM
P.S.I. MIN. (6.2 MPa)
(Cross-linked)
No
ASTM D2671
D570
Dielectric Strength
corrosion Procedure B
200 V/MIL MIN.
(7.9 Kv/mm)
HEAVY-WALL
1.2 MAX. 120°C/
Self
0.5% MAX. Tensile Strength 750
DUAL WALL
16 hrs. Extinguishing
ASTM
P.S.I. MIN. (5.2 MPa)
POLYOLEFIN
No
ASTM D2671
D570
Dielectric Strength
(Cross-linked)
corrosion Procedure C
200 V/MIL MIN.
(7.9 Kv/mm)
POLYVINYL1.35 MAX. 135°C/
Self
1.0% MAX. Tensile Strength 1800
CHLORIDE – PVC
168 hrs. Extinguishing
ASTM
P.S.I. MIN. (MPa)
(Cross-linked/H eat
No
ASTM D876
D570
Dielectric Strength
Shrinkable)
corrosion
280 V/MIL MIN.
HSTTA
HST
HSTTP
HSTTN
HSTTK
HSTTT
HSTTT4X
HSTTF
36
150°C/
Self
1.0% MAX. Tensile Strength 1000 101 1 MIN.
300V/MIL.
16 hrs. Extinguishing
ASTM
P.S.I. MIN. (6.9 MPa)
ASTM
(11.8 Kv/mm) MIN.
(Cross-linked)
No
ASTM D876
D570
Dielectric Strength
D876
ASTM D2671
corrosion
250 V/MIL MIN.
(9.8 Kv/mm)
FLUOROPLASTIC 1.8 MAX. ** NonPass
0.5% MAX. Tensile Strength 5000 101 3 MIN. Size to .500" (12.7mm)
ASTM
corrosive
MIL-DTLASTM
P.S.I. MIN. (34.5 MPa) ASTM
800V/MIL.
KYNAR
(Cross-linked)
D792
23053/8B
D570
Dielectric Strength
D876
(31.5 Kv/mm)min.
4.6.15.3
500 V/MIL MIN.
Over .500" (12.7mm)
(19.7 Kv/mm)
600 V/MIL
(23.6 Kv/mm) min.
ASTM D2671
FLUOROPLASTIC 2.2 MAX. ** NonN/A
0.01%
No change
101 8 MIN.
800 V/MIL.
ASTM
corrosive
NonMAX.
N/A
ASTM
(31.5 Kv/mm) MIN.
TEFLON (TFE) –
Polytetrafluorethylene
D792
flammable
ASTM
D876
ASTM D2671
D570
FLUOROPLASTIC 2.2 MAX. ** NonN/A
0.01%
No change
101 8 MIN.
800 V/MIL.
TEFLON (TFE) –
ASTM
corrosive
NonMAX.
N/A
ASTM
(31.5 Kv/mm) MIN.
Polytetrafluorethylene
D792
flammable
ASTM
D876
ASTM D2671
D570
FLUOROPLASTIC 2.2 MAX. ** NonN/A
0.01%
No change
101 7 MIN.
500 V/MIL. MIN.
TEFLON (FEP) –
corrosive
NonMAX.
N/A
ASTM
(19.7Kv/mm) MIN.
Fluorinated Ethylene
flammable
ASTM
D876
ASTM D2671
Propylene
D570
ELASTOMER
NEOPRENE
Page
No.
4-10
HSTTV
HSTTRA
Dielectric
Strength
500 V/MIL.
(19.7 Kv/mm) MIN.
ASTM D2671
FLEXIBLE
POLYOLEFIN
HSTTVA
Volu me
Resistivity
175°C/
Class 1 Self 0.5% MAX. Tensile Strength 1000 101 4 MIN.
16 hrs. Extinguishing
ASTM
P.S.I. MIN. (6.9MPa)
ASTM
No
Class 2 N/A
D570
Dielectric Strength
D876
corrosion ASTM D2671
400 V/MIL MIN. (15.8
Procedure B
Kv/mm)
HSTT
HSTTR
Class 1,
1.35
(Cross-linked)
Class 2,
1.0
ASTM
D792
HIGHLY FLEXIBLE
1.50
POLYOLEFIN
ASTM
(Cross-linked)
D792
Co pper
Corro sion
1.30
ASTM
D792
** Material is non-corrosive at operating temperatures
KYNAR is a registered trademark of ELF Atochem
TEFLON is a registered trademark of E.I. DuPont Co.
16
19
17
17
18
Power Connectors used with DRY -SHRINK ™ , DAMP -S HRINK ™ and WET-S HRINK ™
Heat Shrink
PANDUIT ® offers a broad line of Power Connectors and Tools for virtually any application in
sizes #14 AWG thru 1000 MCM. See Power Connector Catalog, SA101N15C-NL or Network
Grounding Systems Catalog, SA101N516-NL for complete information.
Selection
Panduit offers two basic styles of connectors, compression and mechanical, for use in grounding
and power cable connections.
Compression Connectors
Compression connectors provide reliable, permanently crimped
connections in sizes matched for each conductor size. They are easy to
install and provide a simplified means of inspection of a proper crimp.
Panduit WET-S HR IN K Type HST Thick Wall Heat Shrink and Panduit
Compression Splice Connectors are UL listed to standard 486D, for direct
burial applications.
WET-SHR IN K Type HST Thick Wall Heat Shrink insulates
Panduit Compression Lug barrels in a wide variety of applications.
Custom Lugs
Panduit has incorporated manufacturing processes that permit quick
custom lug capabilities. Panduit offers a wide variety of dimensional
choices for #8 AWG to 250 MCM copper compression lugs. Contact
factory for complete details.
Panduit DRY -SH RINK Thin Wall Heat Shrink is available in custom cut
lengths. Contact factory for details.
Mechanical Connectors
Panduit offers this economical, reusable type of connector in many styles
in both copper and dual rated aluminum types. Each size connector can
be used for a wide range of conductor sizes which reduces inventory
costs. Special installation tools are not required.
Tooling
Panduit’s broad line of crimping tools include hand operated controlledcycle, hydraulic and battery powered. Also available are UNI-DIE ™
dieless tools.
For complete product and specification information visit our website —
www.panduit.com or call: 866-405-6659
37
Non-Shrink PVC Tubing
PVC Tubing
• Provides insulation and protection for lead
wires, wire harness assemblies, soldered
joints and components in electrical and
electronic equipment
• Material: Polyvinyl chloride (PVC)
• Voltage Rating: 300V and 600V
• All purpose, flexible, non-shrinkable
• Resistant to heat and moisture
• Applicable Specifications:
UL224 VW-1
CSA C22.2 No. 198.1 (OFT)
ASTM D-922, Grade CFR
MIL-I-631, Type F, Form U, Grade C
Class 1, Category 1
VW-1
OFT
The Functional Part Number System Makes Ordering Easy
Non-Shrink PVC Tubing Part Number System
TV105 - 19 M
Type
TV105
38
24
22
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
NominalSize
- 24 AWG
4 - 4 AWG
- 22 AWG
3 - 3 AWG
- 20 AWG
2 - 2 AWG
- 19 AWG
1 - 1 AWG
- 18 AWG
0 - 0 AWG
- 17 AWG
.25 - 1/4"
- 16 AWG
.31 - 5/16"
- 15 AWG
.38 - 3/8"
- 14 AWG
.44 - 6/16"
- 13 AWG
.50 - 1/2"
- 12 AWG
.56 - 9/16"
- 11 AWG
.63 - 5/8"
- 10 AWG
.75 - 3/4"
- 9 AWG
.88 - 7/8"
- 8 AWG
1.0 - 1"
- 7 AWG
1.25 - 1 1/4"
- 6 AWG
1.50 - 1 1/2"
- 5 AWG
Package Quantity
L - 50' (15.2M)
C - 100' (30.5M)
TL - 250' (76.2M)
D - 500' (152.4M)
M - 1000' (304.8M)
2.5M - 2500' (762M)
Non-Shrink PVC Tubing
Type
Materials
Polyvinyl Chloride
TV105
VW-1
OFT
300V/600V**
-4°F to 221° F
(-20°C to 105°C )
MIL-I-631,Type F,
Form U Grade C
Class 1, Cat 1
Highly Flexible
Oil Resistant
Highly Flame
Retardant VW-1
PVC Tubing Ordering Information
Part Number
Clear
Part Number
Black
Nominal Inside Diameter- In. (mm)
Size/
Trade
Name
Maximum
Minimum
Wall
Max.
Thickness
Volt
In. (mm) Rating**
TV105-242.5M TV105-242.5M20 24 AWG .027" (0.68) .020" (0.51) .012" (.30)
TV105-222.5M TV105-222.5M20 22 AWG .032" (0.81) .025" (0.69) .012" (.30)
TV105-20M
TV105-20M20 20 AWG .039" (0.99) .032" (0.81) .016" (.41)
TV105-19M
TV105-19M20 19 AWG .042" (1.06) .036" (0.91) .016" (4.1)
TV105-18M
TV105-18M20 18 AWG .049" (1.24) .040" (1.02) .016" (.41)
TV105-17M
TV105-17M20 17 AWG .053" (1.34) .045" (1.14) .016" (4.1)
TV105-16M
TV105-16M20 16 AWG .061" (1.54) .051" (1.30) .016" (.41)
TV105-15M
TV105-15M20 15 AWG .066" (1.67) .057" (1.45) .016" (4.1)
TV105-14M
TV105-14M20 14 AWG .072" (1.82) .064" (1.63) .016" (.41)
TV105-13M
TV105-13M20 13 AWG .080" (2.03) .072" (1.83) .016" (4.1)
TV105-12D
TV105-12D20 12 AWG .089" (2.26) .081" (2.06) .016" (.41)
TV105-11D
TV105-11D20 11 AWG .101" (2.56) .091" (2.31) .016" (4.1)
TV105-10D
TV105-10D20 10 AWG .112" (2.84) .102" (2.59) .016" (.41)
9 AWG .124" (3.14) .114" (2.90) .020" (.51)
TV105-9D
TV105-9D20
8 AWG .141" (3.58) .129" (3.28) .020" (.51)
TV105-8D
TV105-8D20
7 AWG .158" (4.01) .144" (3.66) .020" (.51)
TV105-7D
TV105-7D20
6
AWG .178" (4.52) .162" (4.11) .020" (.51)
TV105-6TL
TV105-6TL20
5 AWG .198" (5.02) .182" (4.62) .020" (.51)
TV105-5TL
TV105-5TL20
4 AWG .224" (5.68) .204" (5.18) .020" (.51)
TV105-4TL
TV105-4TL20
3 AWG .249" (6.32) .229" (5.82) .020" (.51)
TV105-3TL
TV105-3TL20
2 AWG .278" (7.06) .258" (6.55) .020" (.51)
TV105-2TL
TV105-2TL20
1 AWG .311" (7.89) .289" (7.34) .020" (.51)
TV105-1TL
TV105-1TL20
0 AWG .347" (8.81) .325" (8.26) .020" (.51)
TV105-0TL
TV105-0TL20
1/4"
.265" (6.73) .245" (6.22) .020" (.51)
TV105-.25TL
TV105-.25TL20
5/16"
.334" (8.48) .313" (7.95) .025" (.64)
TV105-.31TL
TV105-.31TL20
3/8"
.399" (10.13) .375" (9.53) .025" (.64)
TV105-.38TL
TV105-.38TL20
7/16"
.462" (11.73) .438" (11.13) .025" (.64)
TV105-.44TL
TV105-.44TL20
1/2"
.524" (13.30) .500" (12.70) .025" (.64)
TV105-.50TL
TV105-.50TL20
9/16"
.585" (14.85) .563" (14.30) .030" (.76)
TV105-.56C
TV105-.56C20
5/8"
.655"(16.63) .625" (15.88) .030" (.76)
TV105-.63C
TV105-.63C20
3/4"
.786" (19.96) .750" (19.05) .035" (.89)
TV105-.75C
TV105-.75C20
7/8"
.911" (23.13) .875" (22.23) .035" (.89)
TV105-.88C
TV105-.88C20
1"
1.036"
(26.31) 1.000" (25.40) .035" (.89)
TV105-1.0L
TV105-1.0L20
1 1/4" 1.290" (32.76) 1.250" (31.75) .040" (1.02)
TV105-1.25L
TV105-1.25L20
1 1/2" 1.550" (39.37) 1.500" (38.10) .045" (1.14)
TV105-1.50L
TV105-1.50L20
* Order in multiples of Std. Pkg. Qty.
300V
300V
300V
300V
300V
300V
300V
300V
300V
300V
300V
300V
300V
300V
300V
300V
300V
300V
300V
300V
300V
300V
300V
300V
600V
600V
600V
600V
600V
600V
600V
600V
600V
600V
600V
Std.
Pkg.
Qty.*
Std.
Ctn.
Qty.
1 Reel, 2500' (762M)
1 Reel, 2500' (762M)
1 Reel, 1000' (304.8M)
1 Reel, 1000' (304.8M)
1 Reel, 1000' (304.8M)
1 Reel, 1000' (304.8M)
1 Reel, 1000' (304.8M)
1 Reel, 1000' (304.8M)
1 Reel, 1000' (304.8M)
1 Reel, 1000' (304.8M)
1 Reel, 500' (152.4M)
1 Reel, 500' (152.4M)
1 Reel, 500' (152.4M)
1 Reel, 500' (152.4M)
1 Reel, 500' (152.4M)
1 Reel, 500' (152.4M)
1 Reel, 250' (76.2M)
1 Reel, 250' (76.2M)
1 Reel, 250' (76.2M)
1 Reel, 250' (76.2M)
1 Reel, 250' (76.2M)
1 Reel, 250' (76.2M)
1 Reel, 250' (76.2M)
1 Reel, 250' (76.2M)
1 Reel, 250' (76.2M)
1 Reel, 250' (76.2M)
1 Reel, 250' (76.2M)
1 Reel, 250' (76.2M)
1 Reel, 100' (30.5M)
1 Reel, 100' (30.5M)
1 Reel, 100' (30.5M)
1 Reel, 100' (30.5M)
1 Reel, 50' (15.2M)
1 Reel, 50' (15.2M)
1 Reel, 50' (15.2M)
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
2 Reels
** UL Voltage Rating is a function of wall thickness.
39
Spiral Wrapping
Abrasion Protection Products
Spiral Wrapping
Features and Benefits
U.L. Recognized
• Largest variety of colors, materials and sizes
• Available in seven different materials and twelve
different colors
• Colors conform to Communications Wiring Standards
• Color code wire bundles
• Flexible, neat, fast
• Allows breakouts of single/multiple wires and
rerouting of replacement wires
• Harness multiple cables into a single
manageable bundle
• Abrasion protection for wires, cables, hoses and tubing
• Reusable
• Tool supplied in each package
Spiral Wrapping Suggested Applications
Use Panduit Spiral Wrapping in office and industrial environments for the following applications:
• Organize wires for communication and computer
equipment where access to the wires is required
• In OEM applications for protecting tubes
and harnesses
• Abrasion protection for control panel wiring
• Personal computer and printer wire organization
• Protect glass tubes from abrasion and breakage
• Kink-proofing for all kinds of tubing... ideal
for laboratories
• Eliminates lacing cord and tie-offs
• Use orange spiral wrapping for protecting and
identifying fiber optic cables
40
Spiral Wrapping
The Functional Part Number System Makes Ordering Easy
Spiral Wrap Part Number Description
T 25 F - C 16
Type
T Spiral
Wrap
Outside Diameter
12 = 1/8"
25 = 1/4"
38 = 3/8"
50 = 1/2"
62 = 5/8"
75 = 3/4"
100 = 1"
Material
F = Polyethylene and
Weather Resistant
Polyethylene
R = Fire Resistant
FR = Flame Retardant
N = Nylon
T = Teflon‡
Package Size
X = 10'
Q = 25'
L - 50'
C - 100'
T = 200'
TL - 250'
D - 500'
M - 1000'
Color Suffix
See Table Below
Color Availability
Material
Color
Color
Suffix*
Natural
(Clear)
Leave
Blank
Weather
Resistant
Black
0
Brown
1
Red
2
Orange
3
Yellow
4
Green
5
Blue
6
Purple
7
Gray
8
White
10
Pink
16
Black
20
Polyethylene
Weather
Resistant
Polyethylene
Fire Resistant
Polyethylene
Flame Retardant
Polyethylene
Natural Color
is White
Natural Color
is White
Weather
Resistant
Nylon
Nylon
TEFLON‡
Blank = Not applicable
* Colors are stocked for 1/4" and 1/2" Polyethylene. Other sizes available. Contact factory.
41
Spiral Wrapping
Ordering Information — Spiral Wrapping
B
A
U.L. Recognized
T
Ordering Information — Spiral Wrapping
Part
Number
Material
Polyethylene
T12F-C
T19F-C
T25F-X
T25F-C
T25F-C1
T25F-C10
T25F-C16
T25F-C2
T25F-C3
T25F-C4
T25F-C5
T25F-C6
T25F-C7
T25F-C8
T38F-C
T50F-X
T50F-C
T50F-C1
T50F-C10
T50F-C16
T50F-C2
T50F-C3
T50F-C4
T50F-C5
T50F-C6
T50F-C7
T50F-C8
T62F-C
T75F-C
T100F-C
Weather
T12F-C0
Resistant
T19F-X0
T25F-X0 Polyethylene
T25F-C0
T38F-C0
T50F-X0
T50F-C0
T62F-C0
T75F-C0
T100F-C0
Color
Natural
Natural
Natural
Natural
Brown
White
Pink
Red
Orange
Yellow
Green
Blue
Purple
Gray
Natural
Natural
Natural
Brown
White
Pink
Red
Orange
Yellow
Green
Blue
Purple
Gray
Natural
Natural
Natural
Black
Black
Black
Black
Black
Black
Black
Black
Black
Black
A
In. (mm)
0.125" (3.2)
0.188" (4.8)
0.25" (6.4)
0.25" (6.4)
0.25" (6.4)
0.25" (6.4)
0.25" (6.4)
0.25" (6.4)
0.25" (6.4)
0.25" (6.4)
0.25" (6.4)
0.25" (6.4)
0.25" (6.4)
0.25" (6.4)
0.375" (9.5)
0.5" (12.7)
0.5" (12.7)
0.5" (12.7)
0.5" (12.7)
0.5" (12.7)
0.5" (12.7)
0.5" (12.7)
0.5" (12.7)
0.5" (12.7)
0.5" (12.7)
0.5" (12.7)
0.5" (12.7)
0.625" (15.9)
0.75" (19.1)
1" (25.4)
0.125" (3.2)
0.188" (4.8)
0.25" (6.4)
0.25" (6.4)
0.375" (9.5)
0.5" (12.7)
0.5" (12.7)
0.625" (15.9)
0.75" (19.1)
1" (25.4)
B
In. (mm)
0.218" (5.5)
0.250" (6.4)
0.375" (9.5)
0.375" (9.5)
0.375" (9.5)
0.375" (9.5)
0.375" (9.5)
0.375" (9.5)
0.375" (9.5)
0.375" (9.5)
0.375" (9.5)
0.375" (9.5)
0.375" (9.5)
0.375" (9.5)
0.437" (11.1)
0.5" (12.7)
0.5" (12.7)
0.5" (12.7)
0.5" (12.7)
0.5" (12.7)
0.5" (12.7)
0.5" (12.7)
0.5" (12.7)
0.5" (12.7)
0.5" (12.7)
0.5" (12.7)
0.5" (12.7)
0.625" (15.9)
0.875" (22.2)
1.125" (28.6)
0.218" (5.5)
0.250" (6.4)
0.375" (9.5)
0.375" (9.5)
0.437" (11.1)
0.5" (12.7)
0.5" (12.7)
0.625" (15.9)
0.875" (22.2)
1.125" (28.6)
T
Bundle Size
In. (mm)
In. (mm)
0.03" (.76)
1/16" (1.6) – 1/2" (12.7)
0.035" (0.89)
1/8" (3.2) - 1" (25.4)
0.04" (1.02)
3/16" (4.8) – 2" (50.8)
0.04" (1.02)
3/16" (4.8) – 2" (50.8)
0.04" (1.02)
3/16" (4.8) – 2" (50.8)
0.04" (1.02)
3/16" (4.8) – 2" (50.8)
0.04" (1.02)
3/16" (4.8) – 2" (50.8)
0.04" (1.02)
3/16" (4.8) – 2" (50.8)
0.04" (1.02)
3/16" (4.8) – 2" (50.8)
0.04" (1.02)
3/16" (4.8) – 2" (50.8)
0.04" (1.02)
3/16" (4.8) – 2" (50.8)
0.04" (1.02)
3/16" (4.8) – 2" (50.8)
0.04" (1.02)
3/16" (4.8) – 2" (50.8)
0.04" (1.02)
3/16" (4.8) – 2" (50.8)
0.055" (1.4)
5/16" (7.9) – 3" (76.2)
0.06" (1.5)
3/8" (9.5) – 4" (101.6)
0.06" (1.5)
3/8" (9.5) – 4" (101.6)
0.06" (1.5)
3/8" (9.5) – 4" (101.6)
0.06" (1.5)
3/8" (9.5) – 4" (101.6)
0.06" (1.5)
3/8" (9.5) – 4" (101.6)
0.06" (1.5)
3/8" (9.5) – 4" (101.6)
0.06" (1.5)
3/8" (9.5) – 4" (101.6)
0.06" (1.5)
3/8" (9.5) – 4" (101.6)
0.06" (1.5)
3/8" (9.5) – 4" (101.6)
0.06" (1.5)
3/8" (9.5) – 4" (101.6)
0.06" (1.5)
3/8" (9.5) – 4" (101.6)
0.06" (1.5)
3/8" (9.5) – 4" (101.6)
0.062" (1.57) 1/2" (12.7) – 4 1/2" (114.3)
0.065" (1.65)
5/8" (15.9) – 5" (127)
0.07" (1.78)
7/8" (22.2) – 6" (152.4)
0.03" (.76)
1/16" (1.6) – 1/2" (12.7)
0.035" (0.89)
1/8" (3.2) - 1" (25.4)
0.04" (1.02)
3/16" (4.8) – 2" (50.8)
0.04" (1.02)
3/16" (4.8) – 2" (50.8)
0.055" (1.4)
5/16" (7.9) – 3" (76.2)
0.06" (1.5
3/8" (9.5) – 4" (101.6)
0.06" (1.5)
3/8" (9.5) – 4" (101.6)
0.062" (1.57) 1/2" (12.7) – 4 1/2" (114.3)
0.065" (1.65)
5/8" (15.9) – 5" (127)
0.07" (1.78)
7/8" (22.2) – 6" (152.4)
*Order in multiples of Std. Pkg. Qty.
NOTE: Custom cut-to-length sizes are available upon request. Contact factory for details.
42
Length
100' (30.5M)
100' (30.5M)
10' (3.0M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
10' (3.0M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
10' (3.0M)
10' (3.0M)
100'(30.5M)
100' (30.5M)
10' (3.0M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
Std.
Pkg.
Qty*
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
1 Pkg.
Spiral Wrapping
B
A
U.L. Recognized
T
Ordering Information — Spiral Wrapping
Part
Number
Material
Color
A
In. (mm)
B
In. (mm)
Fire
White 0.125" (3.2)
0.218" (5.5)
T12R-C
Resistant
White 0.188" (4.8)
0.250" (6.4)
T19R-C
Polyethylene White
0.25" (6.4)
0.375" (9.5)
T25R-C
Black
0.25" (6.4)
0.375" (9.5)
T25R-C20
White 0.375" (9.5) 0.437" (11.1)
T38R-C
White
0.5" (12.7)
0.5" (12.7)
T50R-C
White 0.625" (15.9) 0.625" (15.9)
T62R-C
White 0.75" (19.1) 0.875" (22.2)
T75R-C
White
1" (25.4)
1.125" (28.6)
T100R-C
Flame
White 0.125" (3.2)
0.218" (5.5)
T12FR-C
Black
0.125" (3.2)
0.218" (5.5)
T12FR-C20 Retardant
0.250" (6.4)
T19FR-C Polyethylene White 0.188" (4.8)
Black
0.188" (4.8)
0.250" (6.4)
T19FR-C20
White
0.25" (6.4)
0.375" (9.5)
T25FR-C
Black
0.25" (6.4)
0.375" (9.5)
T25FR-C20
White 0.375" (9.5) 0.437" (11.1)
T38FR-C
Black
0.375" (9.5) 0.437" (11.1)
T38FR-C20
White
0.5" (12.7)
0.5" (12.7)
T50FR-C
Black
0.5" (12.7)
0.5" (12.7)
T50FR-C20
White 0.625" (15.9) 0.625" (15.9)
T62FR-C
Black 0.625" (15.9) 0.625" (15.9)
T62FR-C20
White 0.75" (19.1) 0.875" (22.2)
T75FR-C
Black
0.75" (19.1) 0.875" (22.2)
T75FR-C20
White
1" (25.4)
1.125" (28.6)
T100FR-C
Black
1" (25.4)
1.125" (28.6)
T100FR-C20
Nylon
Natural 0.125" (3.2)
0.218" (5.5)
T12N-C
0.125" (3.2)
0.218" (5.5)
T12N-C0 (Black Nylon Black
is
Natural 0.188" (4.8)
0.250" (6.4)
T19N-C
weather
Black
0.188" (4.8)
0.250" (6.4)
T19N-C0
resistant)
Natural 0.25" (6.4)
0.375" (9.5)
T25N-C
Black
0.25" (6.4)
0.375" (9.5)
T25N-C0
Natural 0.375" (9.5) 0.437" (11.1)
T38N-C
Black
0.375" (9.5) 0.437" (11.1)
T38N-C0
Natural 0.5" (12.7)
0.5" (12.7)
T50N-C
Black
0.5" (12.7)
0.5" (12.7)
T50N-C0
Natural 0.625" (15.9) 0.625" (15.9)
T62N-C
Black 0.625" (15.9) 0.625" (15.9)
T62N-C0
Natural 0.75" (19.1) 0.875" (22.2)
T75N-C
Black
0.75" (19.1) 0.875" (22.2)
T75N-C0
Natural
1" (25.4)
1.125" (28.6)
T100N-C
Black
1" (25.4)
1.125" (28.6)
T100N-C0
TEFLON‡
Natural 0.125" (3.2)
0.218" (5.5)
T12T-C
Natural 0.188" (4.8)
0.250" (6.4)
T19T-C
Natural 0.25" (6.4)
0.375" (9.5)
T25T-L
Natural 0.5" (12.7)
0.5" (12.7)
T50T-Q
Natural 0.625" (15.9) 0.625" (15.9)
T62T-Q
Natural 0.75" (19.1) 0.875" (22.2)
T75T-X
Natural
1" (25.4)
1.125" (28.6)
T100T-X
T
In. (mm)
Bundle Size
In. (mm)
0.03" (.76)
0.035" (0.89)
0.04" (1.02)
0.04" (1.02)
0.055" (1.4)
0.06" (1.5)
0.062" (1.57)
0.065" (1.65)
0.07" (1.78)
0.03" (.76)
0.03" (.76)
0.032" (0.81)
0.032" (0.81)
0.04" (1.02)
0.04" (1.02)
0.055" (1.4)
0.055" (1.4)
0.06" (1.5)
0.06" (1.5)
0.062" (1.57)
0.062" (1.57)
0.065" (1.65)
0.065" (1.65)
0.07" (1.78)
0.07" (1.78)
0.015" (.38)
0.015" (.38)
0.020" (0.51)
0.020" (0.51)
0.023" (.58)
0.023" (.58)
0.03" (.76)
0.03" (.76)
0.032" (.81)
0.032" (.81)
0.035" (.89)
0.035" (.89)
0.04" (1.01)
0.04" (1.01)
0.045" (1.0)
0.045" (1.0)
0.02" (.5)
0.03" (.76)
0.03" (.76)
0.03" (.76)
0.03" (.76)
0.03" (.76)
0.04" (1.01)
1/16" (1.6) – 1/2" (12.7)
1/8" (3.2) – 1" (25.4)
3/16" (4.8) – 2" (50.8)
3/16" (4.8) – 2" (50.8)
5/16" (7.9) – 3" (76.2)
3/8" (9.5) – 4" (101.6)
1/2" (12.7) – 4 1/2" (114.3)
5/8" (15.9) – 5" (127)
7/8" (22.2) – 6" (152.4)
1/16" (1.6) – 1/2" (12.7)
1/16" (1.6) – 1/2" (12.7)
1/8" (3.2) – 1" (25.4)
1/8" (3.2) – 1" (25.4)
3/16" (4.8) – 2" (50.8)
3/16" (4.8) – 2" (50.8)
5/16" (7.9) – 3" (76.2)
5/16" (7.9) – 3" (76.2)
3/8" (9.5) – 4" (101.6)
3/8" (9.5) – 4" (101.6)
1/2" (12.7) – 4 1/2" (114.3)
1/2" (12.7) – 4 1/2" (114.3)
5/8" (15.9) – 5" (127)
5/8" (15.9) – 5" (127)
7/8" (22.2) – 6" (152.4)
7/8" (22.2) – 6" (152.4)
1/16" (1.6) – 1/2" (12.7)
1/16" (1.6) – 1/2" (12.7)
1/8" (3.2) – 1" (25.4)
1/8" (3.2) – 1" (25.4)
3/16" (4.8) – 2" (50.8)
3/16" (4.8) – 2" (50.8)
5/16" (7.9) – 3" (76.2)
5/16" (7.9) – 3" (76.2)
3/8" (9.5) – 4" (101.6)
3/8" (9.5) – 4" (101.6)
1/2" (12.7) – 4 1/2" (114.3)
1/2" (12.7) – 4 1/2" (114.3)
5/8" (15.9) – 5" (127)
5/8" (15.9) – 5" (127)
7/8" (22.2) – 6" (152.4)
7/8" (22.2) – 6" (152.4)
1/16" (1.6) – 1/2" (12.7)
1/8" (3.2) – 1" (25.4)
3/16" (4.8) – 2" (50.8)
3/8" (9.5) – 4" (101.6)
1/2" (12.7) – 4 1/2" (114.3)
5/8" (15.9) – 5" (127)
7/8" (22.2) – 6" (152.4)
Length
Std.
Pkg.
Qty*
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
100' (30.5M) 1
50' (15.2M) 1
25' (7.6M) 1
25' (7.6M) 1
10' (3.0M) 1
10' (3.0M) 1
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
Pkg.
*Order in multiples of Std. Pkg. Qty.
‡ TEFLON or equivalent fluorocarbon PTFE material is used. TEFLON is a registered trademark of E.I. DuPont Co.
NOTE: Custom cut-to-length sizes are available upon request. Contact factory for details.
43
Grommet Edging
PANDUIT
®
Grommet Edging
Grommet Edging Suggested Applications
Features and Benefits
• Nylon grommet edging strips conform
to the Military Standard MS21266
• Use the slotted wall in irregularly
shaped and round panel holes
• Use the solid wall product on
straight edges
Use these tables as a guide to determine PANDUIT Grommet Edging Sizes.
The common sheet metal dimensions listed below are based on the
"Manufacturers Standard Gauge for Steel."
Manufacturer
Standard Gage
Gage for Steel (In.)
Grommet Edging
Military Cross
Reference
GE52-C
GE85-C
GE128-C
GE192-L
GE255-L
GE318-L
GE380-Q
GE510-Q
MS21266-1N
MS21266-2N
MS21266-3N
MS21266-4N
MS21266-5N
MS21266-6N
MS21266-7N
MS21266-8N
5
6
7
8
9
10
11
12
13
0.2092
0.1943
0.1793
0.1644
0.1495
0.1345
0.1196
0.1046
0.0897
Gage
Manufacturer
Standard Gage
for Steel (In.)
14
15
16
17
18
19
20
21
22
0.0747
0.0673
0.0598
0.0538
0.0478
0.0418
0.0359
0.0329
0.0299
Manufacturer
Standard Gage
for Steel (In.)
Gage
23
24
25
26
27
28
29
30
0.0269
0.0239
0.0209
0.0179
0.0164
0.0149
0.0135
0.0120
The Functional Part Number System Makes Ordering Easy
Grommet Edging Part Number Description
Example: GEE 36 F-A-C 0
Part Description
G. Edging/Strips = GE
G. Edging/Slotted = GEE
G. Edging/Solid = GES
44
Max. Panel Thickness
36 = .036" thickness
62 = .062" thickness
F Material
F = Polyethylene
N = Nylon
Adhesive
A = Rubber
Based
Package Size
Q = 25'
L = 50'
C = 100'
Color Suffix
0 = Weather Resistant
Black
Leave Blank = Natural
Grommet Edging
PANDUIT
®
Grommet Edging
Protects and insulates wires and cables from chafing against sharp edges
Choose from five materials:
Nylon
• Self extinguishing
• For indoor use up to 149°F (65°C)
Polyethylene
• General purpose material for indoor use up to 122°F(50°C)
• Style GEE and GES provided in .030" (0.8mm) thick material,
makes them highly flexible
• Available with slotted or solid wall construction
Weather Resistant Polyethylene
• For outdoor use up to 122°F (50°C)
• Excellent resistance to acid rain and ultra-violet light
Flame Retardant Polyethylene
• Will not support a flame
• Available with slotted or solid wall construction
Adhesive Lined Polyethylene
• Base is lined with a pressure sensitive adhesive
• Available in natural and weather resistant
• Adhesive ensures that the product will stay where it is installed
Adhesive Lined
45
Grommet Edging
Ordering Information—Grommet Edging
Dimensions— In. (mm)
Panduit
Part Number
GEE36F-C
GEE36F-C0
GEE62F-C
GEE62F-C0
GEE99F-C
GEE99F-C0
GEE144F-C
GEE144F-C0
GES36F-C
GES36F-C0
GES62F-C
GES62F-C0
GES99F-C
GES99F-C0
GES144F-C
GES144F-C0
GES189F-C
GES189F-C0
GEE62F-A-C
GEE62F-A-C0
GEE99F-A-C
GEE99F-A-C0
GEE144F-A-C
GEE144F-A-C0
GES62F-A-C
GES62F-A-C0
GES99F-A-C
GES99F-A-C0
GES144F-A-C
GES144F-A-C0
GEE36FR-C
GEE62FR-C
GEE99FR-C
GEE144FR-C
GES36FR-C
GES62FR-C
GES99FR-C
GES144FR-C
GEE47N-C
GEE55N-C
GEE71N-C
GEE98N-C
GEE134N-C
Material
Color
Panel Thickness
In. (mm)
Continuous
Polyethylene
(Slotted Wall)
Natural
Black
Natural
Black
Natural
Black
Natural
Black
Natural
Black
Natural
Black
Natural
Black
Natural
Black
Natural
Black
Natural
Black
Natural
Black
Natural
Black
Natural
Black
Natural
Black
Natural
Black
Natural
Natural
Natural
Natural
Natural
Natural
Natural
Natural
Natural
Natural
Natural
Natural
Natural
.026" (.7) – .036" (.9)
.026" (.7) – .036" (.9)
.036" (.9) – .062" (1.6)
.036" (.9) – .062" (1.6)
.062" (1.6) – .099" (2.5)
.062" (1.6) – .099" (2.5)
.099" (2.5) – .144" (3.7)
.099" (2.5) – .144" (3.7)
.026" (.7) – .036" (.9)
.026" (.7) – .036" (.9)
.036" (.9) – .062" (1.6)
.036" (.9) – .062" (1.6)
.062" (1.6) – .099" (2.5)
.062" (1.6) – .099" (2.5)
.099" (2.5) – .144" (3.7)
.099" (2.5) – .144" (3.7)
.144" (3.7) – .189" (4.8)
.144" (3.7) – .189" (4.8)
036" (.9) – .062" (1.6)
.036" (.9) – .062" (1.6)
.062" (1.6) – .099" (2.5)
.062" (1.6) – .099" (2.5)
.099" (2.5) – .144" (3.7)
.099" (2.5) – .144" (3.7)
036" (.9) – .062" (1.6)
.036" (.9) – .062" (1.6)
.062" (1.6) – .099" (2.5)
.062" (1.6) – .099" (2.5)
.099" (2.5) – .144" (3.7)
.099" (2.5) – .144" (3.7)
.026" (.7) – .036" (.9)
.036" (.9) – .062" (1.6)
.062" (1.6) – .099" (2.5)
.099" (2.5) – .144" (3.7)
.026" (.7) – .036" (.9)
.036" (.9) – .062" (1.6)
.062" (1.6) – .099" (2.5)
.099" (2.5) – .144" (3.7)
.020" (.5) – .047" (1.2)
.047" (1.2) – .055" (1.4)
.055" (1.4) – .071" (1.8)
.071" (1.8) – .098" (2.5)
.098" (2.5) – .134" (3.4)
Continuous
Polyethylene
(Solid Wall)
Continuous
Polyethylene
With ADHESIVE
(Slotted Wall)
Continuous
Polyethylene
With ADHESIVE
(Solid Wall)
Flame Retardant
Polyethylene
(Slotted Wall)
Flame Retardant
Polyethylene
(Solid Wall)
Continuous
Nylon
(Slotted Wall)
A
.106" (2.7)
.106" (2.7)
.131" (3.3)
.131" (3.3)
.169" (4.3)
.169" (4.3)
.213" (5.4)
.213" (5.4)
.106" (2.7)
.106" (2.7)
.131" (3.3)
.131" (3.3)
.169" (4.3)
.169" (4.3)
.213" (5.4)
.213" (5.4)
.297" (7.6)
.297" (7.6)
.131" (3.3)
.131" (3.3)
.169" (4.3)
.169" (4.3)
.213" (5.4)
.213" (5.4)
.131" (3.3)
.131" (3.3)
.169" (4.3)
.169" (4.3)
.213" (5.4)
.213" (5.4)
.106" (2.7)
.131" (3.3)
.169" (4.3)
.213" (5.4)
.106" (2.7)
.131" (3.3)
.169" (4.3)
.213" (5.4)
.130" (3.3)
.133" (3.4)
.150" (3.8)
.180" (4.6)
.210" (5.3)
Feet
Per
Pkg.
B
.117"
.117"
.160"
.160"
.186"
.186"
.222"
.222"
.117"
.117"
.160"
.160"
.186"
.186"
.222"
.222"
.301"
.301"
.160"
.160"
.186"
.186"
.222"
.222"
.160"
.160"
.186"
.186"
.222"
.222"
.117"
.160"
.155"
.232"
.117"
.160"
.155"
.232"
.140"
.140"
.140"
.140"
.140"
(3.0)
(3.0)
(4.1)
(4.1)
(4.7)
(4.7)
(5.6)
(5.6)
(3.0)
(3.0)
(4.1)
(4.1)
(4.7)
(4.7)
(5.6)
(5.6)
(7.7)
(7.7)
(4.1)
(4.1)
(4.7)
(4.7)
(5.6)
(5.6)
(4.1)
(4.1)
(4.7)
(4.7)
(5.6)
(5.6)
(3.0)
(4.1)
(3.9)
(5.9)
(3.0)
(4.1)
(3.9)
(5.9)
(3.5)
(3.5)
(3.5)
(3.5)
(3.5)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
100' (30.5M)
Std.
Pkg. Polyethylene
Qty.*
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
Roll
B
Style GEE
Slotted Wall
Continuous
(100 Ft.) Rolls
A
Polyethylene
B
Style GES
Solid Wall
Continuous
(100 Ft.) Rolls
A
Adhesive Lined
Polyethylene
B
Style GEE-A
Slotted Wall
Continuous
(100 Ft.) Rolls
A
Adhesive Lined
Polyethylene
B
Style GES-A
Solid Wall
Continuous
(100 Ft.) Rolls
A
*Order in multiples of Std. Pkg. Qty.
Nylon
Panduit
Part Number
GE52-C
GE52-C69
GE85-C
GE85-C69
GE128-C
GE128-C69
GE192-L
GE192-L69
GE255-L
GE318-L
GE380-Q
GE510-Q
Material
Color
Panel Thickness
In. (mm)
Military
Standard
MS21266
12.75"
Nylon Strips
**
(-69)
designates
Flame
Retardant)
Natural
Natural
Natural
Natural
Natural
Natural
Natural
Natural
Natural
Natural
Natural
Natural
.015" (.4) – .052" (1.3)
.015" (.4) – .052" (1.3)
.052" (1.3) – .085" (2.2)
.052" (1.3) – .085" (2.2)
.085" (2.2) – .128" (3.3)
.085" (2.2) – .128" (3.3)
.128" (3.3) – .192" (4.9)
.128" (3.3) – .192" (4.9)
.192" (4.9) – .255" (6.5)
.255" (6.5) – .318" (8.1)
.318" (8.1) – .380" (9.7)
.380" (9.7) – .510" (13.0)
Pieces
Per
Pkg.
Dimensions — In. (mm)
.150" (3.8)
.150" (3.8)
.175" (4.5)
.175" (4.5)
.220" (5.6)
.220" (5.6)
.325" (8.3)
.325" (8.3)
.385" (9.8)
.455" (11.3)
.515" (13.1)
.640" (16.3)
.155"
.155"
.155"
.155"
.155"
.155"
.230"
.230"
.240"
.255"
.255"
.255"
(3.9)
(3.9)
(3.9)
(3.9)
(3.9)
(3.9)
(5.8)
(5.8)
(6.1)
(6.5)
(6.5)
(6.5)
100 (30.5M)
100 (30.5M)
100 (30.5M)
100 (30.5M)
100 (30.5M)
100 (30.5M)
50 (15.2M)
50 (15.2M)
50 (15.2M)
50 (15.2M)
25 (7.6M)
25 (7.6M)
*Order in multiples of Std. Pkg. Qty.
** Military Standard Nylon Strips (GE Series), order the number of strips required in multiples of Std. Pkg. Qty.
This material is not listed under Military Standard MS21266.
46
Std.
Pkg.
Qty.*
B
B
A
A
Continuous
(100 Ft.) Rolls
Style GEE
Slotted Wall
Strips
Strips
Strips
Strips
Strips
Strips
Strips Nylon
Strips
Strips
Strips B
A
Strips
Strips Style GE
Slotted Wall
12 3/4" strips
Corrugated Loom Tubing
Corrugated Loom Tubing
• PANDUIT ® Corrugated Loom Tubing is offered
for applications where spiral wrapping or braided
expandable sleeving may be difficult to install or
where they do not offer the amount of
protection required.
• Available in Nylon or Polyethylene, this product
features a lengthwise slit which makes it easy to
install onto a bundle of wires or a pre-assembled
harness assembly.
Features and Benefits
• Protects and reduces the risk of damage to wiring
• Crush, impact and abrasion resistant
• Slit wall design for ease of installation
• Available in easy to handle 100' lengths
• Available in black and orange polyethylene and black
heat stabilized nylon
• Mount it in place with push type cable ties, adhesive
or push type mounts.
Corrugated Loom Tubing Suggested Applications
• Bundle wires in control panels
• Contain and organize loose and bundled wiring
harnesses
• Route wires in automotive, truck, trailer, bus,
conversion van, emergency service and recreational
vehicle applications
• Protect wires in off road/mobile equipment
• Use in mining equipment
• Marine applications for protecting wires on boats
and ships
Wiring Accessories for Corrugated Loom Tubing
• Tie Harness Mounts have a specially designed
location tab on the mount that aligns with grooves
in corrugated loom tubing to ensure proper mount
location during assembly. Refer to PANDUIT
Cable Tie and Wiring Accessories Catalog,
SA101N275C-WC for more information.
47
Corrugated Loom Tubing
The Functional Part Number System Makes Ordering Easy
Corrugated Loom Tubing Part Number Description
Example: CLT 100 N-C 630
Part Description
Corrugated Loom
Tubing
CLT= Slit Wall
CLTS= Solid Wall
Bundle Diameter
25 = 1/4"
35 = 5/16"
38 = 3/8"
50 = 1/2"
62 = 5/8"
75 = 3/4"
100 = 1"
125 = 1 1/4"
150 = 1 1/2"
188 = 1 7/8"
Material
N = Heat Stabilized Nylon
F = Polyethylene
Package Size
X = 10’
L = 50'
C = 100'
T = 200’
D = 500'
Color Suffix
630 = Heat Stabilized
Black Nylon
20 = Black Polyethylene
3= Orange
4= Yellow
Ordering Information — Corrugated Loom Tubing
PANDUIT® Part Number
Slit
CLT25F-C20
CLT35F-C20
CLT38F-C20
CLT50F-C20
CLT62F-C20
CLT75F-C20
CLT100F-C20
CLT125F-L20
CLT150F-X20
CLT150F-T20
CLT150F-D20
CLT188F-X20
CLT188F-C20
CLT188F-6C20
CLT25F-C3
CLT35F-C3
CLT38F-C3
CLT50F-C3
CLT62F-C3
CLT75F-C3
CLT100F-C3
CLT125F-L3
CLT150F-X3
CLT150F-T3
CLT150F-D3
CLT188F-X3
CLT188F-C3
CLT188F-6C3
CLT125F-L4
CLT150F-X4
CLT150F-T4
CLT150F-D4
CLT188F-X4
CLT188F-C4
CLT188F-6C4
CLT25N-C630
CLT35N-C630
CLT38N-C630
CLT50N-C630
CLT62N-C630
CLT75N-C630
CLT100N-C630
CLT125N-L630
CLT150N-D630
CLT188N-6C630
Solid
CLTS25F-C
CLTS35F-C
CLTS38F-C
CLTS50F-C
CLTS62F-C
CLTS75F-C
CLTS100F-C
CLTS125F-L
**
**
CLTS150F-D
**
**
**
CLTS25F-C3
CLTS35F-C3
CLTS38F-C3
CLTS50F-C3
CLTS62F-C3
CLTS75F-C3
CLTS100F-C3
CLTS125F-L3
**
**
CLTS150F-D3
**
**
**
**
**
**
**
**
**
**
CLTS25N-C
CLTS35N-C
CLTS38N-C
CLTS50N-C
CLTS62N-C
CLTS75N-C
CLTS100N-C
CLTS125N-L
CLTS150N-D
**
Material
Color
Polyethylene
Black
Polyethylene
Orange
Polyethylene
Yellow
Heat Stabilized
Black Nylon
Black
Inside
Diameter
Outside
Diameter
Feet Per
Pkg.
.265" (6.7)
.350" (8.9)
.414" (10.5)
.505" (12.8)
.665" (16.9)
.760" (19.3)
.915" (23.2)
1.290" (32.8)
1.550" (39.1)
1.550" (39.1)
1.550" (39.1)
1.881" (47.8)
1.881" (47.8)
1.881" (47.8)
.265" (6.7)
.350" (8.9)
.414" (10.5)
.505" (12.8)
.665" (16.9)
.760" (19.3)
.915" (23.2)
1.290" (32.8)
1.550" (39.1)
1.550" (39.1)
1.550" (39.1)
1.881" (47.8)
1.881" (47.8)
1.881" (47.8)
1.290" (32.8)
1.550" (39.1)
1.550" (39.1)
1.550" (39.1)
1.881" (47.8)
1.881" (47.8)
1.881" (47.8)
.265" (6.7)
.350" (8.9)
.414" (10.5)
.505" (12.8)
.665" (16.9)
.760" (19.3)
.915" (23.2)
1.290" (32.8)
1.550" (39.1)
1.881" (47.8)
.390" (9.9)
.500" (12.7)
.556" (14.1)
.670" (17.0)
.830" (21.1)
.935" (23.7)
1.090" (27.7)
1.500" (38.1)
1.860" (47.2)
1.860" (47.2)
1.860" (47.2)
2.169" (55.1)
2.169" (55.1)
2.169" (55.1)
390" (9.9)
.500" (12.7)
.556" (14.1)
.670" (17.0)
.830" (21.1)
.935" (23.7)
1.090" (27.7)
1.500" (38.1)
1.860" (47.2)
1.860" (47.2)
1.860" (47.2)
2.169" (55.1)
2.169" (55.1)
2.169" (55.1)
1.500" (38.1)
1.860" (47.2)
1.860" (47.2)
1.860" (47.2)
2.169" (55.1)
2.169" (55.1)
2.169" (55.1)
.390" (9.9)
.500" (12.7)
.556" (14.1)
.670" (17.0)
.830" (21.1)
.935" (23.7)
1.090" (27.7)
1.500" (38.1)
1.860" (47.2)
2.169" (55.1)
100'
100'
100'
100'
100'
100'
100'
50'
10'
200'
500'
10'
100'
600'
100'
100'
100'
100'
100'
100'
100'
50'
10'
200'
500'
10'
100'
600'
50'
10'
200'
500'
10'
100'
600'
100'
100'
100'
100'
100'
100'
100'
50'
500'
600'
*Order number of rolls required.
**Contact factory for additional sizes, materials, colors, and bulk packaging.
48 NOTE: Custom cut-to-length sizes are available upon request. Contact factory for details.
Pkg.
Qty.*
1 Roll
1 Roll
1 Roll
1 Roll
Braided Expandable Sleeving
Braided Expandable Sleeving — Polyethylene Terephthalate — PET
• Provides continuous abrasion resistance for wires, cables and
tubing
• Lightweight, durable protection
• Highly flexible open weave will not trap heat or humidity
• Rated for use up to 257°F (125°C)
• Allows for use with irregular shapes
• Stock colors: Black, gray and white
• See page 50 for cutting tools
The Functional Part Number System Makes Ordering Easy
Braided Expandable Sleeving Part Number Description
Example: SE 25 PFR-M R 0
Part Description
Sleeving
Expandable
Nom. I.D. Size
12 = 1/8" (3.2)
25 = 1/4" (6.4)
38 = 3/8" (9.5)
50 = 1/2" (12.7)
75 = 3/4" (19.1)
125 = 1 1/4 " (31.8)
Material
P = Polyethylene Terephthalate (PET)
PFR = Polyethylene Terephthalate (PET)
Flame Retardant
PFRLD = PET Light duty braid construction
(Flame Retardant)
PLD = PET Light duty braid construction
Package Size
R = Reel
L = 50' (15.2M)
C = 100' (30.5M)
T = 200' (61.0M)
D = 500' (152.4M)
M = 1000' (304.8M)
Color Suffix
0 = Black
8 = Gray
10 = White
150 = 1 1/2 " (38.1)
175 = 1 3/4 " (44.5)
Ordering Information — Braided Expandable Sleeving
Part Number
Black
SE12P-TR0
SE12P-MR0
SE25P-TR0
SE25P-MR0
SE25PLD-MR0
SE38P-TR0
SE38P-MR0
SE50P-CR0
SE50P-DR0
SE75P-CR0
SE75P-DR0
SE125P-LR0
SE125P-TR0
SE150P-LR0
SE150P-TR0
SE175P-TR0
Part Number
Gray
SE12P-TR8
SE12P-MR8
SE25P-TR8
SE25P-MR8
—
SE38P-TR8
SE38P-MR8
SE50P-CR8
SE50P-DR8
SE75P-CR8
SE75P-DR8
SE125P-LR8
SE125P-TR8
SE150P-LR8
SE150P-TR8
—
* Order number of reels required.
Part Number
White
—
SE12P-MR10
—
SE25P-MR10
—
—
SE38P-MR10
—
SE50P-DR10
—
SE75P-DR10
—
SE125P-TR10
—
SE150P-TR10
—
Nominal
I.D.
Inches (mm)
Nominal
Diameter Range
Inches (mm)
Std.
Pkg.
Qty.*
Std.
Ctn.
Qty.
.125" (3.2)
.094" to .250"
(2.4) to (6.4)
.125" to .375"
(3.2) to (9.5)
1 Reel, 200' (61.0M)
1 Reel, 1000' (304.8M)
1 Reel, 200' (61.0M)
1 Reel, 1000' (304.8M)
1 Reel, 1000’ (304.8M)
1 Reel, 200' (61.0M)
1 Reel, 1000' (304.8M)
1 Reel, 100' (30.5M)
1 Reel, 500' (152.4M)
1 Reel, 100' (30.5M)
1 Reel, 500' (152.4M)
1 Reel, 50' (15.2M)
1 Reel, 200' (61.0M)
1 Reel, 50' (15.2M)
1 Reel, 200' (61.0M)
1 Reel, 200' (61.0M)
4 Reels
2 Reels
4 Reels
2 Reels
2 Reels
4 Reels
2 Reels
4 Reels
2 Reels
4 Reels
2 Reels
4 Reels
2 Reels
4 Reels
2 Reels
2 Reels
.250" (6.4)
.375" ((9.5)
.500" (12.7)
.750" (19.1)
1.25" (31.8)
1.50" (38.1)
1.75" (44.5)
.188" to .562"
(4.7) to (14.3)
.250" to .750"
(6.4) to (19.1)
.500" to 1.25"
(12.7) to (31.8)
.750" to 1.50"
(19.1) to (38.1)
1.00" to 2.25"
(25.4) to (57.2)
1.25" to 2.75"
(31.8) to (69.8)
49
Flame Retardant Braided Expandable Sleeving
Braided Expandable Sleeving —
Flame Retardant Polyethylene Terephthalate — PET
• Provides continuous abrasion resistance for wires, cables and
tubing
• Lightweight, durable protection
• Highly flexible open weave will not trap heat or humidity
• Rated for use up to 257°F (125°C)
• Allows for use with irregular shapes
• Self extinguishing, meets UL VW-1
• Stock colors: Black or gray with white tracer, or in white with
black tracer to identify flame retardant material
• See bottom of this page for cutting tools
Ordering Information — Flame Retardant Braided Expandable Sleeving
Part Number
Black
Part Number
Gray
SE12PFR-TR0
SE12PFR-MR0
SE25PFR-TR0
SE25PFR-MR0
SE25PFRLD-MR0
SE38PFR-TR0
SE38PFR-MR0
SE50PFR-CR0
SE50PFR-DR0
SE75PFR-CR0
SE75PFR-DR0
SE125PFR-LR0
SE125PFR-TR0
SE150PFR-LR0
SE150PFR-TR0
SE175PFR-TR0
Part Number
White
SE12PFR-TR8
SE12PFR-MR8
SE25PFR-TR8
SE25PFR-MR8
—
SE38PFR-TR8
SE38PFR-MR8
SE50PFR-CR8
SE50PFR-DR8
SE75PFR-CR8
SE75PFR-DR8
SE125PFR-LR8
SE125PFR-TR8
SE150PFR-LR8
SE150PFR-TR8
—
—
SE12PFR-MR10
—
SE25PFR-MR10
—
—
SE38PFR-MR10
—
SE50PFR-DR10
—
SE75PFR-DR10
—
SE125PFR-TR10
—
SE150PFR-TR10
—
Nominal
I.D.
Inches (mm)
Nominal
Diameter Range
Inches (mm)
Std.
Pkg.
Qty.*
Std.
Ctn.
Qty.
.125" (3.2)
.094" to .250"
(2.4) to (6.4)
.125" to .375"
(3.2) to (9.5)
1 Reel, 200' (61.0M)
1 Reel, 1000' (304.8M)
1 Reel, 200' (61.0M)
1 Reel, 1000' (304.8M)
1 Reel, 1000’ (304.8M)
1 Reel, 200' (61.0M)
1 Reel, 1000' (304.8M)
1 Reel, 100' (30.5M)
1 Reel, 500' (152.4M)
1 Reel, 100' (30.5M)
1 Reel, 500' (152.4M)
1 Reel, 50' (15.2M)
1 Reel, 200' (61.0M)
1 Reel, 50' (15.2M)
1 Reel, 200' (61.0M)
1 Reel, 200' (61.0M)
4 Reels
2 Reels
4 Reels
2 Reels
2 Reels
4 Reels
2 Reels
4 Reels
2 Reels
4 Reels
2 Reels
4 Reels
2 Reels
4 Reels
2 Reels
2 Reels
.250" (6.4)
.375" (9.5)
.500" (12.7)
.750" (19.1)
1.25" (31.8)
1.50" (38.1)
1.75" (44.5)
.188" to .625"
(4.7) to (15.9)
.250" to .750"
(6.4) to (19.1)
.500" to 1.25"
(12.7) to (31.8)
.750" to 1.50"
(19.1) to (38.1)
1.00" to 2.25"
(25.4) to (57.2)
1.25" to 2.75"
(31.8) to (69.8)
* Order number of reels required.
Tooling Head (HKBS)
Bench Mount Cutter/End Sealer
Sleeving Cutter/End Sealer Blade —
Available Directly from Manufacturer
Used with popular soldering guns to cut and seal sleeving.
Part Number
Description
HKBS
For dual straight shank soldering guns with .500" spacing
Typical Guns: WELLER straight shank Model 8200; WEN
Model 199 or 100
* Order number of blades required.
50
Std.
Pkg.
Qty*
1
Pearson Industries
P.O. Box 36
Prattville, AL 36067
(334) 365-5416
Flammability Tests and Classifications
Abrasion Protection Products Flammability Tests and Classifications
• A number of test procedures have been developed
which can be used for the evaluation and comparison
of various materials to suppor t combustion.
• Review the following classifications to find which
category is designed to suit your abrasion and
protection applications.
UL94 Vertical Burning Test
Samples of material, with dimension 5" by 1/2" and the thickness of the intended end use product, are tested
in a unaged “as manufactured” state and in an aged state (7 days at 158F° ,70°C). The test requires the
placement of a precisely controlled flame under a vertically supported specimen for a 10 second period.
The flame is removed and the duration of flaming is recorded. If the flame extinguishes, the specimen is
immediately subjected to a second 10 second ignition period. Duration of flaming is again recorded. A piece
of surgical cotton is placed under the specimen. If drips ignite the cotton, this fact is also recorded.
MATERIALS CLASSIFIED 94V-0
Materials classified 94V-0 shall:
• Not have any specimens which burn with flaming combustion for more than 10 seconds after either
application of the test flame.
• Not have a total flaming combustion time exceeding 50 seconds for the 10 flame applications for each set
of five specimens.
• Not have any specimens which burn with flaming or glowing combustion up to the holding clamp.
• Not have any specimens which drip flaming particles that ignite the dr y absorbent surgical cotton located
12" (305mm) below the test specimen.
• Not have any specimens with glowing combustion which persists for more than 30 seconds after the
second removal of the test flame.
(Cont. on page 52)
51
Flammability Tests and Classifications
MATERIALS CLASSIFIED 94V-1
Materials classified 94V-1 shall:
• Not have a total flaming combustion time exceeding 250 seconds for the 10 flame applications for each
set of five specimens.
• Not have any specimens which burn with flaming or glowing combustion up to the holding clamp.
• Not have any specimens which drip flaming par ticles that ignite the dry absorbent surgical cotton located
12"(305mm) below the test specimen.
• Not have an specimens with glowing combustion which persists for more than 60 seconds after the
second removal of the test flame.
MATERIALS CLASSIFIED 94V-2
Materials classified 94V-2 shall:
• Not have any specimens which burn with flaming combustion for more than 30 seconds after either
application of the test flame.
• Not have a total flaming combustion time exceeding 250 seconds for the 10 flame applications for each set
of five specimens.
• Not have any specimens which burn with flaming or glowing combustion up to the holding clamp.
• Be permitted to have specimens which drip flaming particles which burn only briefly some of which ignite
the dry absorbent surgical cotton located 12" (305mm) below the test specimen.
• Not have any specimens with glowing combustion which persists for more than 60 seconds after the
second removal of the test flame.
MATERIALS CLASSIFIED UL-94 HB
• Specimens shall have a maximum burn rate of 1.5 in./min over 3 inches of thickness of 0.120" to 0.5".
• Specimens shall have a maximum burn rate of 2.5 in./min over 3 inches for a thickness less than 0.120".
UL224 VERTICAL WIRE FLAME TEST
Samples of fully recovered tubing are placed over a length of fine spring steel music wire. The test requires
the precise placement of a controlled flame that contacts the heat shrink tubing. The flame is applied in five
fifteen second intervals with a time period between applications. If the flame extinguishes immediately after
the first flame removal, subsequent flame applications are made to the tubing. Duration of specimen flaming
is noted. A piece of surgical cotton is placed under the specimen. If a flaming or glowing piece of tubing
drips and ignites the cotton, this is also noted.
MATERIALS CLASSIFIED AS VW-1 SHALL:
• Not flame or glow longer than 60 seconds following any of the five applications of the flame.
• Not ignite or damage more than 25% of kraft paper flag that is placed around the top of the tubing.
• Not have any specimens which drip flaming par ticles and ignite the surgical cotton located 9 1/2 inches
below the test specimen.
52
CLT
Nylon
Our Nylon is strong, durable, selfextinguishing material for indoor use up
to 149°F. It offers a combination of
lightweight, wide temperature range,
and high abrasion resistance. T his
material is suitable for applications
where heavy vibration or stress exists on
the wiring or tubing.
Weather Resistan t Nylon
T his material has the same
properties as natural Nylon and also has
additives which allow it to resist the
effects of ultraviolet light in an outdoor
environment. T his product is available in
black only.
T EF LON‡
T his material is a non-flammable,
fluorocarbon resin material.
Suitable for use in any application
(including nuclear containment). It is
rated up to 356°F.
Color: Natural with a bluish cast.
Polyethylene Terephthalate (PET)
T his material is a thermoplastic polyester
material designed for indoor applications.
It is rated for use up to 257°F.
Colors: Black, White and Gray.
F lam e Ret. Polyethylene
Terephth alate (PET)
T his material is a self-extinguishing
thermoplastic polyester that can be used
indoors. It is also rated for use up to
257°F and is provided in black with white
tracer (to identify the flame retardant
material).
Natural Polyethylene
Our lowest cost material is for
continuous use at temperatures
-40°F (-40°C) to 176°F (80°C).
Nylon
Nylon is a strong, durable, high abrasion
resistant material for continuous use at
temperatures
-40°F (-40°C) to 248°F (120°C).
.03%
Resistant
below 140°F
(60°C) except
to chlorinated
solvents
Resistant
Resistant
except to
No
oxidizing Discoloration
acids
Resistant
Resistant
except to
Some
oxidizing Discoloration
acids
Resistant
Resistant
except to
Some
oxidizing Discoloration
acids
Resistant
Resistant
to most
No
weak
Discoloration
acids
Resistant
Resistant
to most
No
weak
Discoloration
acids
Resistant
Resistant
except to
No
fluorine
Discoloration
and some
halogens
22 mg
1400
(D638)
Petro-Ch em icals
2000
(D638)
Minimum Tensile
@ 23°C (psi)
Resistant
except to
Some
oxidizing Discoloration
acids
Specific
Gravity
(D792)
Resistant
Abrasio n
Resistan ce
(Lower n umber
is better)
.01%
Resistant
below 140°F
(60°C) except
to chlorinated
solvents
.91
.93
HB
239°F
(115°C)
HB
239°F
(115°C)
20 mg
.93
1.09
V-2
239°F
(115°C)
27 mg
1.00
1.30
1400
(D638)
.02%
V-0
270°F
(132°C)
22 mg
1.38
1200
.02%
-40°F
(-40°C)
to
149°F
(65°C)
V-2
491°F
(255°C)
7 mg
1.03
1.15
12,400
(D638)
1.5%
Resistant
except to
phenols
and formic
acid
-40°F
(-40°C)
to
149°F
(65°C)
V-2
491°F
(255°C)
7 mg
1.03
1.15
12,400
(D638)
1.5%
Resistant
except to
phenols
and formic
acid
-40°F
(-40°C)
to
365°F
(180°C)
V-0
520°F
(271°C)
7 mg
2.10
2.20
2500
(D638)
.01%
-94°F
(-70°C)
to
257°F
(125°C)
HB
500°F
(260°C)
Contact
Factory
1.31
100,000
(D638)
.08%
Not
Not
No
Resistant
Recommended Recommended
Discoloration
-94°F
(-70°C)
U.L. 224: 445°F
to
VW-1 (230°C)
257°F
(125°C)
Contact
Factory
1.39
37,500
(D638)
.08%
Not
Not
No
Recommended Recommended Resistant Discoloration
-40°F
(-40°C)
to
122°F
(50°C)
-40°F
(-40°C)
to
122°F
(50°C)
-40°F
(-40°C)
to
140°F
(60°C)
Resistant
below 140°F
(60°C) except
to chlorinated
solvents
Resistant
below 140°F
(60°C) except
to chlorinated
solvents
Resistant
Acid s
Melting
Temperature
Weather Resistan t Po lyethylene
T his material has the same
properties as natural polyethylene, and
also has additives which allow it to resist
the effects of ultraviolet light and acid rain
in an outdoor environment. This product
is available in black only.
F lam e Retardan t Polyethylene UL94V2 Rating
T his material is self extinguishing and
passes the UL94 flame
retardant test with a V2 rating
F lam e Retardan t Polyethylene UL94V0 Rating
T his material is self extinguishing and
passes the UL94 flame
retardant test with a V0 rating
Ch emical Resistan ce
Alkalies
-40°F
(-40°C)
to
122°F
(50°C)
Physical Properties
Organic
Solvents
UL
Temperature
Index
Natural Polyethylene
Our lowest cost material for indoor use
up to 122°F. Natural is available in all
sizes. Colors are available in 1/4" and
1/2".
Rating s and Approvals
Water Absorptio n
(Max. 24 hrs.)
Abrasion
Protection
Materials
Technical Data
Flammability
(UL 94)
SLEEVING
SPIRAL
WRAPPING
SPIRAL WRAPPING & GROMMET EDGING
Abrasion Protection Products Technical Data
N/A
HB
Contact
Factory
Contact
Factory
.926.940
1529 Contact
(D638) Factory
Excellent
Excellent
Excellent
Good
N/A
HB
437°F
(225°C)
Contact
Factory
1.061.16
10,000 Contact
(D638) Factory
Excellent
Good
Fair
Good
NOTE: Typical operating temperature ranges are extended based on end use application and specific environmental tests.
‡Teflon or equivalent fluorocarbon PTFE is used. Teflon is the registered trademark of E. I. DuPont.
53
Abrasion Protection Products Technical Data
The approximate required length of spiral wrapping based on the bundle diameter can be determined by using the graphs below;
they show length required (in feet) per foot of bundle.
54
Alphabetical Part Number Index
Part
Number
CLT
Page
*F - * ......................................................48
*N - *......................................................48
CLTS
*F - * ......................................................48
*N - *......................................................48
GE
* - * ........................................................46
GEE
*F - * ......................................................46
*F - A - *.................................................46
*FR - *....................................................46
*N - *......................................................46
GES
*F - * ......................................................46
*F - A - *.................................................46
*FR - *....................................................46
HKBS ..............................................................50
HSEC *.* - *......................................................24
HSG
-115V - 300............................................27
-115V - 500............................................27
-115V - 650............................................27
HSG - A1 to HSG - A4.........................................27
HSG - P1 to HSG - P7.........................................27
HST
.* - * - *...................................................23
HSTT * - * ........................................................4 - 7
* - 48 - *.................................................4 - 7
* - *F ......................................................10
* - *FC....................................................10
* - *K ......................................................10
* - *KC ...................................................10
* - Q.......................................................4 - 7
* - Y .......................................................8
* - YK1...................................................9
* - YK2...................................................9
HSTTA * - 48 - *.................................................21
* - Y .......................................................21
Part
Number
Page
HSTTD * - 48 - *.................................................10
HSTTF * - 48 - *.................................................18
HSTTK * - 48 - *.................................................19
HSTTN * - 48 - *.................................................16
HSTTP * - *........................................................ 15
HSTTR * - 48 - *.................................................14
HSTTRA* - 48 - *.................................................22
HSTTT * - 48 - *.................................................17
HSTTT4X* - 48 - * ...............................................17
HSTTV * - *........................................................ 11
* - 48 - *.................................................11
* - D....................................................... 12
* - M....................................................... 12
* - Q....................................................... 13
* - T ....................................................... 12
* - Y ....................................................... 13
HSTTVA* - 48 - *5
* - Y ....................................................... 20
SE
*P - *...................................................... 49
*PFR - *.................................................50
T
*F - *...................................................... 42
*FR - * ................................................... 43
*N - *...................................................... 43
*R - *...................................................... 43
*T - *...................................................... 43
TV105 -*............................................................ 39
55
Proof Positive of
Panduit Quality
With all the talk about high quality, it’s nice to hear a completely
objective voice now and then. ISO 9001 certification is proof positive
that Panduit’s focus on quality is from top to bottom and everywhere
in between.
The ISO 9001 recognition indicates that we meet the most
comprehensive international standards in design, purchasing,
manufacturing, testing, documentation, shipping and service.
And this means Panduit’s high-quality products and services help
you meet your ISO 9000 requirements while also reducing your
quality and inspection costs.
The following Panduit products are manufactured at
ISO 9001 registered Panduit facilities:
Cable Ties
Heat Shrink and Abrasion Protection Products
Identification/Safety Products
Network Connectivity Products
Power Connectors
Stainless Steel Ties & Accessories
Surface Raceway
Terminals
Wiring Accessories
Wiring Duct
Focused on t he Future
Tin ley Park, IL 60477-3091
Fax 708-532-1811
Internet Email: info@pandu it.com
Website: www.p anduit.com/eeg
56
工商网监
湘ICP备2023018690号
