DI108_T0_00001

DI100~DI1010 DUAL-IN-LINE GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER VOLTAGE 50 to 1000 Volt 1 Ampere CURRENT Recongnized File #E111753 FEATURES • Low leakage • Surge overload rating-- 30 amperes peak • Ideal for printed circuit board 0.255(6.5) 0.245(6.2) 0.315(8.00) 0.285(7.24) • Plastic material used carries Underwriters Laboratory recognition 94V-O 0.350(8.9) 0.300(7.6) 0.335(8.51) 0.316(8.05) 0.098(2.5) 0.086(2.2) • Lead free in compliance with EU RoHS 2011/65/EU directive • Green molding compound as per IEC61249 Std. . (Halogen Free) MECHANICALDATA 0.045(1.14) 0.035(0.89) • Case: Reliable low cost construction utilizing molded plastic technique results in 0.022(0.56) 0.018(0.46) 0.185(4.69) 0.150(3.81) inexpensive product • Terminals: Lead solderable per MIL-STD-750, Method 2026 • Polarity: Polarity symbols molded or marking on body 0.075(1.90) 0.055(1.39) • Weight: 0.012 ounces, 0.33 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified.Single phase, half wave, 60Hz, Resistive or inductive load. For capacitive load, derate current by 20% PARAM ETER SY M BO L DI 1 00 DI 101 DI 102 DI 10 4 DI 106 DI 10 8 DI 1010 UNI TS M aximum Recur r ent Peak Rever se Volt age V RRM 50 100 200 40 0 600 800 1000 V M aximum RM S Br idge I nput Volt age V RM S 35 70 140 28 0 420 560 700 V M aximum DC Bloc king Volt age V DC 50 100 200 40 0 600 800 1000 V M aximum Aver age For w ar d Cur r e nt I AV 1 A Peak For w ar d Sur ge Cur r ent : 8. 3ms s ingle half s ine- w ave s uper impos ed on r at ed load I FSM 30 A I 2 t Rat ing f or f us ing ( t < 8. 35ms ) I 2t 3. 735 A 2t M aximum For w ar d Volt age Dr op per Br idge Element at 1A VF 1. 1 V IR 5 500 uA CJ 25 pF R θ JA R θJ L 40 15 T J , T STG - 55 t o + 150 M aximum DC Rever s e Cur r ent at Rat ed DC Bloc k ing Volt age Ty pic al J unc t ion Cap acit anc e ( Not e 1) Ty pic al Ther mal Resist a nc e Per Leg ( Not e 2 ) O per at ing J uns t ion and St or age Temper at ur e Range T J = 25 O C T J = 125 O C O C / W O C NOTES : 1. Measured at 1 MHz and applied reverse voltage of 4 Volts 2. Thermal resistance from junction to ambient and from junction to lead mounted on P.C.B. with 0.5 X 0.5"(13 X 13mm) copper pads March 11,2016-REV.02 PAGE . 1 DI100~DI1010 3.0 2.5 2.0 1.5 1.0 0.5 0 0 50 100 150 INSTANTANEOUS FWD CUTTENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES RATING AND CHARACTERISTIC CURVES O T J =25 C Pulse Width = 200uS O AMBIENT TEMPERATURE, C INSTANTANEOUS FWD VOLTAGE, VOLTS 10 O TA = 100 C 1.0 0.1 TA= 25 O C 0.01 0 20 40 60 80 100 120 140 PERCENT OF PEAK REVERSE VOLTAGE, % FIG.3 TYPICAL REVERSE CHARACTERISTICS March 11,2016-REV.02 FIG.2 TYPICAL FORWARD CHARACTERISTICS FORWARD SURGE CURRENT, AMPERES pk (HALF SINE-WAVE) INSTANTANEOUS REVERSE CURRENT,uA F I G . 1 D E R AT I N G C U RV E F O R O U T P U T RECTIFIED CURRENT 50 40 30 20 10 0 1 2 6 10 20 40 60 100 NO. OF CYCLES AT 60Hz FIG.4 MAX NON-REPETITIVE SURGE CURRENT PAGE . 2 DI100~DI1010 Part No_packing code_Version DI100_T0_00001 For example : RB500V-40_R2_00001 Serial number Part No. Version code means HF Packing size code means 13" Packing type means T/R Packing Code XX Packing type Tape and Ammunition Box (T/B) Tape and Reel (T/R) Bulk Packing (B/P) Tube Packing (T/P) Tape and Reel (Right Oriented) (TRR) Tape and Reel (Left Oriented) (TRL) FORMING March 11,2016-REV.02 Version Code XXXXX 1st Code Packing size code A N/A 0 HF 0 serial number R 7" 1 RoHS 1 serial number B 13" 2 T 26mm X S 52mm Y L F PANASERT T/B CATHODE UP (PBCU) PANASERT T/B CATHODE DOWN (PBCD) 2nd Code HF or RoHS 1st Code 2nd~5th Code U D PAGE . 3 DI100~DI1010 Disclaimer • Reproducing and modifying information of the document is prohibited without permission from Panjit International Inc.. • Panjit International Inc. reserves the rights to make changes of the content herein the document anytime without notification. Please refer to our website for the latest document. • Panjit International Inc. disclaims any and all liability arising out of the application or use of any product including damages incidentally and consequentially occurred. • Panjit International Inc. does not assume any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. • Applications shown on the herein document are examples of standard use and operation. Customers are responsible in comprehending the suitable use in particular applications. Panjit International Inc. makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. • The products shown herein are not designed and authorized for equipments requiring high level of reliability or relating to human life and for any applications concerning life-saving or life-sustaining, such as medical instruments, transportation equipment, aerospace machinery et cetera. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Panjit International Inc. for any damages resulting from such improper use or sale. • Since Panjit uses lot number as the tracking base, please provide the lot number for tracking when complaining. March 11,2016-REV.02 PAGE . 4