ER1001F

DATA SHEET ER1000F~ER1004F ISOLATION SUPERFAST RECOVERY RECTIFIERS VOLTAGE FEATURES .112(2.85) .100(2.55) .272(6.9) .248(6.3) 50 to 400 Volts CURRENT 10 Amperes ITO-220AC Unit : inch (mm) • Plastic package has Underwriters Laboratory Flammability Classification 94V-O. Flame Retardant Epoxy Molding Compound. • Exceeds environmental standards of MIL-S-19500/228 • Low power loss, high efficiency. • High surge capacity. • Super fast recovery times, high voltage. • Both normal and Pb free product are available : Normal : 80~95% Sn, 5~20% Pb Pb free: 98.5% Sn above • Low forwrd voltge, high current capability .406(10.3) .381(9.7) .134(3.4) .118(3.0) .189(4.8) .165(4.2) .130(3.3) .114(2.9) .606(15.4) .583(14.8) MECHANICALDATA Case: ITO-220AC Molded plastic Terminals: Lead solderable per MIL-STD-202, Method 208 Polarity: As marked. Standard packaging: Any Weight: 0.08 ounces, 2.24grams. .055(1.4) .039(1.0) .035(0.9) .011(0.3) .1 (2.55) .1 (2.55) .161(4.1)MAX .543(13.8) .512(13.0) .071(1.8) .055(1.4) .114(2.9) .098(2.5) .032(.8) MAX MAXIMUM RATING AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% PA RA M E TE R M a xi m um R e c ur r e nt P e a k R e ve r s e V o l t a g e M a xi m um R M S V o l t a g e M a xi m um D C B l o c k i ng V o l t a g e M a xi m um A ve r a g e F o r w a r d C ur r e nt . 3 7 5 " ( 9 . 5 m m ) l e a d l e n g t h a t Tc = 1 0 0 O C P e a k F o r w a r d S ur g e C ur r e nt , 8 . 3 m s s i ng l e ha l f s i ne - w a ve s up e r i m p o s e d o n r a t e d l o a d ( J E D E C m e t ho d ) M a xi m um F o r w a r d V o l t a g e a t 1 0 A , p e r e l e m e nt M a x i m u m D C R e v e r s e C u r r e n t a t TA = 2 5 O C R a t e d D C B l o c k i n g V o l t a g e TA = 1 0 0 O C M a x i m u m R e v e r s e R e c o v e r y Ti m e ( N o t e 2 ) Ty p i c a l J u n c t i o n c a p a c i t a n c e ( N o t e 1 ) M a xi m um The r m a l R e s i s t a nc e O p e r a t i n g J u n c t i o n a n d S t o r a g e Te m p e r a t u r e R a n g e S YM B O L V RRM V RMS V DC IAV IF S M VF IR T RR CJ R θJ C T J , T S TG E R1 0 0 0 F 50 35 50 E R1 0 0 1 F 100 70 100 E R1 0 0 1 A F 150 105 150 1 0 .0 150 E R1 0 0 2 F 200 140 200 E R1 0 0 3 F 300 210 300 E R1 0 0 4 F 400 280 400 U N IT S V V V A A 0 .9 5 10 500 35 62 3 .0 - 5 0 TO + 1 5 0 1 .3 0 V uA 50 ns pF O C/W O C NOTES: 1. Measured at 1 MHz and applied reverse voltage of 4.0 VDC. 2. Reverse Recovery Test Conditions: IF=.5A, IR=1A, Irr=.25A. 3. Both Bonding and Chip structure are available. STAD-APR.19.2004 PAGE . 1 RATING AND CHARACTERISTIC CURVES AVERAGE FORWARD CURRENT, AMPERES 8 6 4 .375"9.5mm LEADLENGHTS RESISTIVEORINDUCTIVE LOAD PEAK FORWARD SURGE CURRENT, 10 150 125 100 75 50 25 0 8.3ms Single Half Since-Wave JEDEC Method 2 0 0 20 40 60 80 100 O 120 140 160 1 2 5 10 20 50 100 CASE TEMPERAURE, C Fig.1- FORWARD CURRENT DERATING CURVE NO. OF CYCLE AT 60HZ Fig.2- MAXIMUM NON - REPETITIVE SURGE CURRENT 10 3 40 FORWARD CURRENT, AMPERES 20 10 8 6 4 2 1.0 .8 .6 .4 .2 50-200V REVERSE CURRENT, uA 10 2 T J =125 C O 300-400V 10 1 10 0 10 -1 T J =25 C O T A =25 C O 10 -2 .1 20 40 60 80 100 120 .6 .7 .8 .9 1.0 1.1 1.2 1.3 PERCENT OF RATED PEAK REVERSE VOLTAGE, % FORWARD VOLATGE, VOLTS Fig.3- TYPICAL REVERSE CHARACTERISTIC Fig.4- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTIC STAD-APR.19.2004 PAGE . 2