ER1E_R1_00001

ER2000FCT~ER2006FCT ISOLATION SUPERFAST RECOVERY RECTIFIER VOLTAGE 50 to 600 Volt 20 Ampere CURRENT FEATURES • Plastic package has Underwriters Laboratory Flammability Classification 94V-O. Flame Retardant Epoxy Molding Compound. • Low power loss, high efficiency. • Low forward voltage, high current capability • High surge capacity. • Super fast recovery times, high voltage. • Epitaxial chip construction. • Lead free in compliance with EU RoHS 2.0 • Green molding compound as per IEC 61249 standard MECHANICALDATA • Case: ITO-220AB Molded plastic • Terminals: Lead solderable per MIL-STD-750, Method 2026 • Polarity: As marked. • Standard packaging: Any • Weight: 0.056 ounces, 1.6 grams. MAXIMUM RATING AND ELECTRICAL CHARACTERISTICSS Ratings at 25°C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% PARAMETER SYMBOL ER2000FCT ER2001FCT ER2001AFCT ER2002FCT ER2003FCT ER2004FCT ER2006FCT UNITS Maximum Recurrent Peak Reverse Voltage VRRM 50 100 150 200 300 400 600 V Maximum RMS Voltage VRMS 35 70 105 140 210 280 420 V Maximum DC Blocking Voltage VDC 50 100 150 200 300 400 600 V Maximum Average Forward Current IF(AV) 20 A Peak Forward Surge Current : 8.3ms single half sine-wave superimposed on rated load IFSM 150 A Maximum Forward Voltage at 10A VF Maximum DC Reverse Current at Rated DC Blocking Voltage TJ= 25 OC TJ= 100 OC 0.95 1.3 V 1 500 IR Maximum Reverse Recovery Time (Note 2) trr Typical Junction Capacitance (Note 1) CJ 85 Typical thermal Resistance (Note 3) RθJc 3 TJ,TSTG -50 to +150 Operating Junction and Storage Temperature Range 1.7 35 μA 50 ns pF O C/W O C NOTES: 1. Measured at 1 MHz and applied reverse voltage of 4 VDC. 2. Reverse Recovery Test Conditions: IF=0.5A, IR=1A, Irr=0.25A. 3. Both Bonding and Chip structure are available. July 17,2017­REV.08 PAGE . 1 ER2000FCT~ER2006FCT 20 16 12 6 RESISTIVEORINDUCTIVE LOAD 4 0 0 20 40 60 80 100 120 140 160 INSTANTANEOUS FORWARD CURRENT AMPERES AVERAGE FORWARD CURRENT, AMPERES RATING AND CHARACTERISTIC CURVES 50 50-200V 10 300-400V 1.0 600V T J= 25 OC Pulse Width=200us 0.1 0 .8 1.0 . 1.2 1.4 1.6 1.8 O CASE TEMPERAURE, C INSTANTANEOUS FORWARD VOLTAGE, VOLTS Fig.2- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTIC Fig.1- FORWARD CURRENT DERATING CURVE O TJ= 125 C 100 180 PEAK FORWARD SURGE CURRENT, INVSTANTANEOUS REVERSE CURRENT, MICROAMPERES 1000 O TJ= 75 C 10 150 8.3ms Single Half Since-Wave JEDEC Method 120 90 60 25 0 1 2 5 10 20 50 100 NO. OF CYCLE AT 60HZ 1.0 O TJ= 25 C Fig.4- MAXIMUM NON - REPETITIVE SURGE CURRENT 0.1 20 40 60 80 100 120 90 PERCENT OF RATED PEAK INVERSE VOLTGE, VOLTS 80 FIG.3 TYPICAL REVERSE CHARACTERISTICS CAPACITANCE, pF 70 60 O TJ = 25 C 50 40 30 20 10 1 2 5 10 20 50 100 200 500 REVERSE VOLTAGE, VOLTS Fig.5- TYPICAL JUNCTION CAPACITANCE July 17,2017­REV.08 PAGE . 2 ER2000FCT~ER2006FCT Part No_packing code_Version ER2000FCT_T0_00001 For example : RB500V-40_R2_00001 Serial number Part No. Version code means HF Packing size code means 13" Packing type means T/R Packing Code XX Packing type Tape and Ammunition Box (T/B) Tape and Reel (T/R) Bulk Packing (B/P) Tube Packing (T/P) Tape and Reel (Right Oriented) (TRR) Tape and Reel (Left Oriented) (TRL) FORMING July 17,2017­REV.08 Version Code XXXXX 1st Code Packing size code A N/A 0 HF 0 serial number R 7" 1 RoHS 1 serial number B 13" 2 T 26mm X S 52mm Y L F PANASERT T/B CATHODE UP (PBCU) PANASERT T/B CATHODE DOWN (PBCD) 2nd Code HF or RoHS 1st Code 2nd~5th Code U D PAGE . 3 ER2000FCT~ER2006FCT Disclaimer • Reproducing and modifying information of the document is prohibited without permission from Panjit International Inc.. • Panjit International Inc. reserves the rights to make changes of the content herein the document anytime without notification. Please refer to our website for the latest document. • Panjit International Inc. disclaims any and all liability arising out of the application or use of any product including damages incidentally and consequentially occurred. • Panjit International Inc. does not assume any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. • Applications shown on the herein document are examples of standard use and operation. Customers are responsible in comprehending the suitable use in particular applications. Panjit International Inc. makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. • The products shown herein are not designed and authorized for equipments requiring high level of reliability or relating to human life and for any applications concerning life-saving or life-sustaining, such as medical instruments, transportation equipment, aerospace machinery et cetera. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Panjit International Inc. for any damages resulting from such improper use or sale. • Since Panjit uses lot number as the tracking base, please provide the lot number for tracking when complaining. July 17,2017­REV.08 PAGE . 4