ER2D_R1_00001

ER2A~ER2J SURFACE MOUNT RECTIFIER VOLTAGE 50 to 600 Volt CURRENT 2 Ampere FEATURES • For surface mounted applications in order to optimize board space • High temperature metallurgically bonded-no compression contacts as found in other diode-constructed rectifiers • Glass passivated junction • Easy pick and place • Plastic package has Underwriters Laboratory Flammability Classification 94V-O • Lead free in compliance with EU RoHS 2.0 • Green molding compound as per IEC 61249 standard MECHANICAL DATA • Case: JEDEC DO-214AA molded plastic • Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 • Polarity: Color band denotes cathode end • Standard packaging: 16mm tape (EIA-481) • Weight: 0.0032 ounces, 0.092 grams 1 2 Cathode Anode MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. PARAMETER SYMBOL ER2A ER2B ER2C ER2D ER2E ER2G ER2J UNITS Maximum Recurrent Peak Reverse Voltage VRRM 50 100 150 200 300 400 600 V Maximum RMS Voltage VRMS 35 70 105 140 210 280 420 V Maximum DC Blocking Voltage VDC 50 100 150 200 300 400 600 V Maximum Average Forward Current TL=110OC IF(AV) 2 A Peak Forward Surge Current : 8.3ms single half sine-wave superimposed on rated load IFSM 50 A Maximum Forward Voltage at 2A VF 0.95 1.25 1.7 V IR 1 150 μA Maximum Reverse Recovery Time (Note 1) trr 35 ns Typical Junction Capacitance (Note 2) CJ 25 pF Typical Thermal Resistance (Note 3) RθJL 20 O Typical Thermal Resistance (Note 3) RθJC 15 O TJ,TSTG -55 to +150 Maximum DC Reverse Current at Rated DC Blocking Voltage Operating Junction and Storage Temperature Range TJ=25OC TJ=100OC C/W C/W C O NOTES:1. Reverse Recovery Test Conditions: I F=0.5A, I R=-1A, I rr=-0.25A 2. Measured at 1 MHz and applied Vr = 4 volts. 3. Mounted on a FR4 PCB, single-sided copper, with 100cm 2 copper pad area. May 7,2018­REV.10 PAGE . 1 ER2A~ER2J RATING AND CHARACTERISTIC CURVES 70 60 2.4 2 .0 CAPACITANCE, pF AVERAGE FORWARD RECIFIED CURRENT AMPERES 2.8 1.6 1 .2 .8 SINGLE PHASE, HALF-WAVE, 60Hz RESISTIVE OR INDUCTIVE LOAD P.C.B MOUNTED ON 0.3 x 0.3" (8.0 x 8.0 mm)COPPER PAD AREAS .4 20 40 60 80 40 30 20 O TJ = 25 C f = 1.0MHZ Vsig = 50mVp-p 10 0 0 50 100 120 140 160 180 0 0.1 LEAD TEMPERATURE, OC 1 10 100 1000 REVERSE VOLTAGE, VOLTS FIG.2 TYPICAL JUNCTION CAPACITANCE FIG.1 MAXIMUM AVERAGE FORWARD CURRENT RATING 100 INSTANTANEOUS FORWARD CURRENT AMPERES INVSTANTANEOUS REVERSE CURRENT, MICROAMPERES 1000 O TJ= 125 C 100 O TJ= 75 C 10 1.0 0.1 O TJ= 25 C 20 40 60 80 100 10 50-200V 300-400V 1.0 600V 0.1 O T J = 25 C 120 .01 0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 PERCENT OF RATED PEAK INVERSE VOLTGE, VOLTS INSTANTANEOUS FORWARD VOLTAGE VOLTS FIG.3 TYPICAL REVERSE CHARACTERISTICS FIG.4 TYPICAL FORWARD CHARACTERISTICS FORWARD SURGE CURRENT, AMPERES (HALF-SING WAVE) 60 50 40 30 20 10 8.3ms SINGLE HALF SINE-WAVE JEDC METHOD 0 1 5 10 50 100 NUMBER OF CYCLES AT 60Hz FIG.5 MAXIMUM NON-REPEITIVE SURGE CURRENT May 7,2018­REV.10 PAGE . 2 ER2A~ER2J MOUNTING PAD LAYOUT ORDER INFORMATION • Packing information T/R - 3K per 13" plastic Reel T/R - 0.8K per 7" plastic Reel May 7,2018­REV.10 PAGE . 3 ER2A~ER2J Part No_packing code_Version ER2A_R1_00001 ER2A_R2_00001 For example : RB500V-40_R2_00001 Serial number Version code means HF Packing size code means 13" Part No. Packing type means T/R Packing Code XX Packing type Tape and Ammunition Box (T/B) Tape and Reel (T/R) Bulk Packing (B/P) Tube Packing (T/P) Tape and Reel (Right Oriented) (TRR) Tape and Reel (Left Oriented) (TRL) FORMING May 7,2018­REV.10 Version Code XXXXX 1st Code Packing size code A N/A 0 HF 0 serial number R 7" 1 RoHS 1 serial number B 13" 2 T 26mm X S 52mm Y L F PANASERT T/B CATHODE UP (PBCU) PANASERT T/B CATHODE DOWN (PBCD) 2nd Code HF or RoHS 1st Code 2nd~5th Code U D PAGE . 4 ER2A~ER2J Disclaimer • Reproducing and modifying information of the document is prohibited without permission from Panjit International Inc.. • Panjit International Inc. reserves the rights to make changes of the content herein the document anytime without notification. Please refer to our website for the latest document. • Panjit International Inc. disclaims any and all liability arising out of the application or use of any product including damages incidentally and consequentially occurred. • Panjit International Inc. does not assume any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. • Applications shown on the herein document are examples of standard use and operation. Customers are responsible in comprehending the suitable use in particular applications. Panjit International Inc. makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. • The products shown herein are not designed and authorized for equipments requiring high level of reliability or relating to human life and for any applications concerning life-saving or life-sustaining, such as medical instruments, transportation equipment, aerospace machinery et cetera. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Panjit International Inc. for any damages resulting from such improper use or sale. • Since Panjit uses lot number as the tracking base, please provide the lot number for tracking when complaining. May 7,2018­REV.10 PAGE . 5