GPJ8B

GPJ8A~GPJ8M GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER VOLTAGE FEATURES • Plastic material has Underwriters Laboratory, Flammability Classification 94V-O .112(3.1) 50 to 1000 Volts CURRENT 8.0 Ampere G PJ Unit: inch (mm) • Ideal for printed circuit board • Reliable low cost construction utilizing molded plastic technique • High temperature soldering guaranteed: 260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension .133(3.4) 1.192(30.3) 1.169(29.7) .133(3.4) .112(3.1) .208(5.3) .189(4.8) .171(4.35) .159(4.05) .165(4.2) .149(3.8) .709(18.0) .669(17.0) MECHANICALDATA • Case: Reliable low cost construction utilizing • molded plastic technique • Terminals: Leads solderable per MIL-STD-750,Method 2026 • Mounting position: Any • Mounting torque: 5 in. lb. Max. • Weight: 0.15 ounce, 4.0 grams .087(2.2) .070(1.8) .044(1.1) .035(0.9) .401(10.2) .385(9.8) .133(3.4) .125(3.2) .304(7.7) .288(7.3) .304(7.7) .288(7.3) .032(0.8) .024(0.6) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz. For Capacitive load derate current by 20%. PA RA M E TE R M a xi m um R e c ur r e nt P e a k R e ve r s e V o l t a g e M a x i m u m R M S B r i d g e In p u t V o l t a g e M a xi m um D C B l o c k i ng V o l t a g e M a xi m um A ve r a g e F o r w a r d T C = 1 0 0 OC R e c t i f i e d O ut p ut C ur r e nt a t T A = 4 0 OC I2 t R a t i n g f o r f u s i n g ( t < 8 . 3 m s ) P e a k F o r w a r d S ur g e C ur r e nt s i ng l e s i ne - w a ve s up e r i m p o s e d o n r a t e d l o a d ( J E D E C m e t ho d ) M a x i m u m In s t a n t a n e o u s F o r w a r d V o l t a g e D r o p p e r e l e m e n t a t 4 .0 A M a xi m um R e ve r s e L e a k a g e C ur r e nt a t R a t e d @ T J = 2 5 OC D c B l o c k i ng V o l t a g e @ T J = 1 0 0 OC Ty p i c a l T h e r m a l R e s i s t a n c e p e r l e g ( N o t e 2 ) (No te 3 ) O p e r a t i n g J u n c t i o n a n d S t o r a g e Te m p e r a t u r e R a n g e S YM B O L GP J 8 A GP J 8 B GP J 8 D 50 35 50 100 70 100 200 140 200 G P J 8 G G P J 8 J G P J 8 K G P J 8 M U N IT S 400 280 400 8 .0 6 .0 166 200 1 .1 10 500 8 .6 3 .1 O V RRM V RMS V DC IF ( A V ) I2 t IF S M VF IR R θJ A R θJ C 600 420 600 800 560 800 1000 700 1000 .480(12.2) .464(11.8) • Pb free product are available : 99% Sn above can meet RoHS environment substance diective request .799(20.3) .775(19.7) V V V A A2sec Apk Vpk uA C /W T J ,T S T G -5 5 to + 1 5 0 O C NOTES: 1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw. 2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads. 3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate. STAD-MAY.23.2006 PAGE . 1 GPJ8A~GPJ8M RATING AND CHARACTERISTIC CURVES FORWARD SURGE CURRENT, AMPERES pk (HALF SINE-WAVE) AVERAGE FORWARD CURRENT AMPERES 8.0 200 6.0 160 4.0 HEAT-SINK MOUNTING, T C (4 x 4 x 0.15cm)THK COPPER PLATE 120 80 2.0 MOUNTED ON PC BOARD, TA 0.5 (12.7mm)LEAD LENGTH 60Hz RESISTIVE OR INDUCTIVE LOAD 40 0 0 50 100 O 150 0 1 2 6 10 20 40 60 100 TEMPERATURE, C NO. OF CYCLES AT 60Hz Fig.1 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT Fig.2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 10 INSTANTANEOUS FORWARD CURRENT, AMPERES 4 100 40 20 10 4.0 2.0 1.0 10 3 REVERSE CURRENT,uA 10 2 T J =150 OC 10 1 10 0 T J =25 C O 10 -1 0.4 0.2 0.1 0.7 0.8 0.9 1.0 1.1 TJ=25 C Pulse Width = 300us 1% DULY Cycle O 10 -2 0 10 20 30 40 50 60 70 80 90 100 110 1.2 1.3 1.4 PERCENT OF PEAK REVERE VOLTAGE,% INSTANTANEOUS FORWARD VOLTAGE, VOLTS Fig.3 - TYPICAL REVERSE CHARACTERISTICS Fig.4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER ELEMENT STAD-MAY.23.2006 PAGE . 2