GPJ8A~GPJ8M
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
VOLTAGE FEATURES
• Plastic material has Underwriters Laboratory, Flammability Classification 94V-O
.112(3.1)
50 to 1000 Volts CURRENT
8.0 Ampere
G PJ
Unit: inch (mm)
• Ideal for printed circuit board • Reliable low cost construction utilizing molded plastic technique • High temperature soldering guaranteed: 260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
.133(3.4)
1.192(30.3) 1.169(29.7)
.133(3.4) .112(3.1)
.208(5.3) .189(4.8) .171(4.35) .159(4.05)
.165(4.2) .149(3.8)
.709(18.0) .669(17.0)
MECHANICALDATA
• Case: Reliable low cost construction utilizing • molded plastic technique • Terminals: Leads solderable per MIL-STD-750,Method 2026 • Mounting position: Any • Mounting torque: 5 in. lb. Max. • Weight: 0.15 ounce, 4.0 grams
.087(2.2) .070(1.8) .044(1.1) .035(0.9) .401(10.2) .385(9.8)
.133(3.4) .125(3.2)
.304(7.7) .288(7.3)
.304(7.7) .288(7.3)
.032(0.8) .024(0.6)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz. For Capacitive load derate current by 20%.
PA RA M E TE R M a xi m um R e c ur r e nt P e a k R e ve r s e V o l t a g e M a x i m u m R M S B r i d g e In p u t V o l t a g e M a xi m um D C B l o c k i ng V o l t a g e M a xi m um A ve r a g e F o r w a r d T C = 1 0 0 OC R e c t i f i e d O ut p ut C ur r e nt a t T A = 4 0 OC I2 t R a t i n g f o r f u s i n g ( t < 8 . 3 m s ) P e a k F o r w a r d S ur g e C ur r e nt s i ng l e s i ne - w a ve s up e r i m p o s e d o n r a t e d l o a d ( J E D E C m e t ho d ) M a x i m u m In s t a n t a n e o u s F o r w a r d V o l t a g e D r o p p e r e l e m e n t a t 4 .0 A M a xi m um R e ve r s e L e a k a g e C ur r e nt a t R a t e d @ T J = 2 5 OC D c B l o c k i ng V o l t a g e @ T J = 1 0 0 OC Ty p i c a l T h e r m a l R e s i s t a n c e p e r l e g ( N o t e 2 ) (No te 3 ) O p e r a t i n g J u n c t i o n a n d S t o r a g e Te m p e r a t u r e R a n g e
S YM B O L
GP J 8 A GP J 8 B GP J 8 D 50 35 50 100 70 100 200 140 200
G P J 8 G G P J 8 J G P J 8 K G P J 8 M U N IT S 400 280 400 8 .0 6 .0 166 200 1 .1 10 500 8 .6 3 .1
O
V RRM V RMS V DC IF ( A V ) I2 t IF S M VF IR
R θJ A R θJ C
600 420 600
800 560 800
1000 700 1000
.480(12.2) .464(11.8)
• Pb free product are available : 99% Sn above can meet RoHS environment substance diective request
.799(20.3) .775(19.7)
V V V A A2sec Apk Vpk uA C /W
T J ,T S T G
-5 5 to + 1 5 0
O
C
NOTES: 1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw. 2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads. 3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate.
STAD-MAY.23.2006
PAGE . 1
GPJ8A~GPJ8M
RATING AND CHARACTERISTIC CURVES
FORWARD SURGE CURRENT, AMPERES pk (HALF SINE-WAVE)
AVERAGE FORWARD CURRENT AMPERES
8.0
200
6.0
160
4.0
HEAT-SINK MOUNTING, T C (4 x 4 x 0.15cm)THK COPPER PLATE
120
80
2.0
MOUNTED ON PC BOARD, TA 0.5 (12.7mm)LEAD LENGTH 60Hz RESISTIVE OR INDUCTIVE LOAD
40
0 0 50 100
O
150
0
1
2
6
10
20
40
60
100
TEMPERATURE, C
NO. OF CYCLES AT 60Hz
Fig.1 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT
Fig.2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT
10
INSTANTANEOUS FORWARD CURRENT, AMPERES
4
100 40 20 10 4.0 2.0 1.0
10
3
REVERSE CURRENT,uA
10
2
T J =150 OC
10
1
10
0
T J =25 C
O
10
-1
0.4 0.2 0.1 0.7 0.8 0.9 1.0 1.1
TJ=25 C Pulse Width = 300us 1% DULY Cycle
O
10
-2
0
10 20
30 40
50
60
70
80
90 100 110
1.2
1.3
1.4
PERCENT OF PEAK REVERE VOLTAGE,%
INSTANTANEOUS FORWARD VOLTAGE, VOLTS
Fig.3 - TYPICAL REVERSE CHARACTERISTICS
Fig.4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER ELEMENT
STAD-MAY.23.2006
PAGE . 2
很抱歉,暂时无法提供与“GPJ8J”相匹配的价格&库存,您可以联系我们找货
免费人工找货