MUR460_AY_00101

MUR460 SUPERFAST RECOVERY RECTIFIERS 600 Volt VOLTAGE CURRENT 4 Ampere DO-201AD Unit: inch(mm) FEATURES .052(1.3) .048(1.2) 1.0(25.4)MIN. • Superfast recovery times-epitaxial construction • Low forward voltage, high current capability • Hermetically sealed • Low leakage .375(9.5) • Plastic package has Underwriters Laboratories Flammability Classification 94V-O utilizing Flame Retardant Epoxy Molding Compound. .210(5.3) .188(4.8) 1.0(25.4)MIN. • Lead free in compliance with EU RoHS 2.0 .285(7.2) • High surge capability MECHANICALDATA • Case: Molded plastic, DO-201AD • Terminals: Axial leads, solderable to MIL-STD-750,Method 2026 • Polarity: Color band denotes cathode end • Approx. Weight: 0.0396 ounce, 1.122 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. Resistive or inductive load, 60Hz. PARAMETER SYMBOL MUR460 UNITS Maximum Recurrent Peak Reverse Voltage VRRM 600 V Maximum RMS Voltage VRMS 420 V Maximum DC Blocking Voltage VDC 600 V Maximum Average Forward Current .375"(9.5mm) lead length at TA=55OC IF(AV) 4.0 A Peak Forward Surge Current : 8.3ms single half sine-wave superimposed on rated load(JEDEC method) IFSM 125 A Maximum Forward Voltage at 4.0A VF 1.28 V Maximum DC Reverse Current at Rated DC Blocking Voltage TA=25OC Maximum DC Reverse Current at Rated DC Blocking Voltage TA=125OC IR 5 300 μA Maximum Reverse Recovery Time(Note 1) trr 50 ns Typical Junction capacitance (Note 2) CJ 35 pF RθJA RθJC 20 13 TJ,TSTG -55 to +150 Typical Thermal Resistance(Note 3) Operating and Storage Temperature RangeTJ,TSTG C/W O C O NOTES:1. Reverse Recovery Test Conditions: IF=.5A, IR=1A, Irr=.25A 2. Measured at 1 MHz and applied reverse voltage of 4.0 VDC 3. Thermal resistance from junction to ambient and from junction to lead length 0.375"(9.5mm) P.C.B. mounted September 17,2020 MUR460_(L0)-REV.00 PAGE . 1 MUR460 50 W Naninductive 10 W Naninductive t rr + 0.5A (- ) 0 (+ ) 25Vdc (appr ox) (- ) PULSE GENERATOR NOTE 2 1W Naninductive (+ ) OSCILLOSCOPE NOTE 1 - 0.25 - 1.0 SET TIME BASE FOR 10ns/cm NOTES:1.Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF 2.Rise Time = 10ns max. Source Impedance = 50 Ohms 1cm FORWARD SURGE CURRENT, AMPERES pk (HALF-SING WAVE) RATING AND CHARACTERISTIC CURVES 175 150 8.3ms SINGLE HALF SINE-WAVE JEDEC M ETHOD 125 100 75 50 25 1 5 2 10 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.1 REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM AVERAGE FORWARD RECIFIED CURRENT AMPERES 4 3 2 MAXIMUM AVERAGE CURRENT RATING SINGLE PHASE, HALF-WAVE, 60Hz RESISTIVE OR INDUCTIVE LOAD .375" (9mm) LEAD LENGTHS 1 0 0 20 40 60 80 100 120 140 160 180 O AMBIENT TEMPERATURE, C 100 10 1.0 O T= 25 C J PULSE WIDTH= 300 mS 2%DUTY CYCLE 0.1 .3 1000 .5 .7 .9 1.1 1.3 1.5 1.7 1.9 INSTANTANEOUS FORWARD VOLTAGE VOLTS FIG.4 TYPICAL JUNCTION CAPACITANCE TJ= 125 O C 100 100 O TJ= 75 C JUNCTION CAPACITANCE, pF IR - REVERSE LEAKAGE CURRENT. MICRO AMPERES FIG.3 MAXIMUM AVERAGE FORWARD CURRENT RATING INSTANTANEOUS FORWARD CURRENT AMPERES FIG.2 MAXIMUM NON-REPEITIVE SURGE CURRENT 10 1.0 O TJ= 25 C 0.1 20 40 60 80 100 120 10 1 PERCENT OF INSTANTANEOUS REVERSE VOLTAGE,(%) FIG.5 TYPICAL REVERSE CHARACTERISTICS September 17,2020 1 10 100 REVERSE VOLTAGE, VOLTS FIG.6 TYPICAL JUNCTION CAPACITANCE MUR460_(L0)-REV.00 PAGE . 2 MUR460 Part No. Packing Code Version Part No. Packing Code Package Type Packing Type Marking Version MUR460_AY_00101 DO-201AD 1250pcs / Ammo MUR460 Halogen free MUR460_B0_00101 DO-201AD 500pcs / Box MUR460 Halogen free MUR460_R2_00101 DO-201AD 1250pcs / 13” reel MUR460 Halogen free September 17,2020 MUR460_(L0)-REV.00 PAGE . 3 MUR460 Disclaimer • Reproducing and modifying information of the document is prohibited without permission from Panjit International Inc.. • Panjit International Inc. reserves the rights to make changes of the content herein the document anytime without notification. Please refer to our website for the latest document. • Panjit International Inc. disclaims any and all liability arising out of the application or use of any product including damages incidentally and consequentially occurred. • Panjit International Inc. does not assume any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. • Applications shown on the herein document are examples of standard use and operation. Customers are responsible in comprehending the suitable use in particular applications. Panjit International Inc. makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. • The products shown herein are not designed and authorized for equipments requiring high level of reliability or relating to human life and for any applications concerning life-saving or life-sustaining, such as medical instruments, transportation equipment, aerospace machinery et cetera. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Panjit International Inc. for any damages resulting from such improper use or sale. • Since Panjit uses lot number as the tracking base, please provide the lot number for tracking when complaining. September 17,2020 MUR460_(L0)-REV.00 PAGE . 4