SMF5.0A_R1_00001

SMF5.0A~SMF175A SURFACE MOUNT TRANSIENT VOLTAGE SUPPRESSOR VOLTAGE 5 to 175 Volt SOD-123FL 200 Watt POWER Unit：inch(mm) 0.075(1.90) 0.067(1.70) • For surface mounted applications in order to optimize board space. • Ultra Thin Profile Package for Space Constrained Utilization • Package suitable for Automated Handling 0.115(2.90) 0.106(2.70) 0.044(1.10) 0.031(0.80) FEATURES 0.044(1.10) 0.035(0.90) • Low inductance • High temperature soldering : 260OC/10 seconds at terminals • ESD IEC-61000-4-2 Air + 30kV, Contact + 30kV • Lead free in compliance with EU RoHS 2.0 • Green molding compound as per IEC 61249 standard 0.145(3.70) 0.137(3.50) 0.008(0.20) 0.004(0.10) 0.030(0.75) 0.017(0.45) MECHANICAL DATA • Case: SOD-123FL, Plastic • Terminals: Solderable per MIL-STD-750, Method 2026 • Polarity: Color band denotes cathode end • Weight: 0.0006 ounces, 0.0173 grams • Standrad Packaging: 8mm tape (EIA-481) 1 Cathode 2 Anode o MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS (TA=25 C unless otherwise noted) PARAMETER SYMBOL VALUE UNITS Peak Pulse Power Dissipation on TA = 25OC (Notes 1,2,5) Fig.1 PPPM 200 W Peak Forward Surge Current per (Notes 3) I FSM 20 A Peak Pulse Current on tp=10/1000μs waveform (Notes 1) Fig.3 I PPM Steady State Power Dissipation (Notes 4) PM(AV) 1 W ESD IEC-61000-4-2 (Air) ESD IEC-61000-4-2 (Contact) VESD +30 +30 kV TJ,TSTG -55 to +150 O C RθJA 180 O C Operating Junction and Storage Temperature Range Typical thermal resistance see Table 1 A NOTES : 1.Non-repetitive current pulse, per Fig.3 and derated above T A=25 OC per Fig.2 . 2.Mounted on 5mm2 copper pads to each terminal. 3.8.3ms single half sine-wave, or equivalent square wave, duty cycle = 4 pulses per minutes maximum. 4.Lead temperature at 75OC =TL . 5.Peak pulse power waveform is tp=10/1000μs. 6.A transient suppressor is selected according to the working peak reverse voltage(VRWM ), which should be equal to or greater than the DC or continuous peak operating voltage level. March 9,2018-REV.12 PAGE . 1 SMF5.0A~SMF175A Part Number V RWM (No te 6 ) V V BR @ IT IR @ VRWM M i n. Ma x. IT V V mA μA VC @ IPP Marking Code V A 200W Transient Voltage Suppressor SMF5.0A 5 6.4 7 10 200 9.2 21.7 HE SMF6.0A 6 6.7 7.4 10 100 10.3 19.4 HG SMF6.5A 6.5 7.2 8 10 75 11.2 17.9 HK SMF7.0A 7 7.8 8.6 10 50 12 16.7 HM SMF7.5A 7.5 8.3 9.2 1 50 12.9 15.5 HP SMF8.0A 8 8.9 9.8 1 25 13.6 14.7 HR SMF8.5A 8.5 9.4 10.4 1 10 14.4 13.9 HT SMF9.0A 9 10 11.1 1 5 15.4 13 HV SMF10A 10 11.1 12.3 1 2.5 17 11.8 HX SMF11A 11 12.2 13.5 1 2.5 18.2 11 HZ SMF12A 12 13.3 14.7 1 2.5 19.9 10.1 IE SMF13A 13 14.4 15.9 1 1 21.5 9.3 IG SMF14A 14 15.6 17.2 1 1 23.2 8.6 IK SMF15A 15 16.7 18.5 1 1 24.4 8.2 IM SMF16A 16 17.8 19.7 1 1 26 7.7 IP SMF17A 17 18.9 20.9 1 1 27.6 7.2 IR SMF18A 18 20 22.1 1 1 29.2 6.8 IT SMF20A 20 22.2 24.5 1 1 32.4 6.2 IV SMF22A 22 24.4 26.9 1 1 35.5 5.6 IX SMF24A 24 26.7 29.5 1 1 38.9 5.1 IZ SMF26A 26 28.9 31.9 1 1 42.1 4.8 JE SMF28A 28 31.1 34.4 1 1 45.4 4.4 JG SMF30A 30 33.3 36.8 1 1 48.4 4.1 JK SMF33A 33 36.7 40.6 1 1 53.3 3.8 JM SMF36A 36 40 44.2 1 1 58.1 3.4 JP SMF40A 40 44.4 49.1 1 1 64.5 3.1 JR SMF43A 43 47.8 52.8 1 1 69.4 2.9 JT SMF45A 45 50 55.3 1 1 72.7 2.8 JV SMF48A 48 53.3 58.9 1 1 77.4 2.6 JX SMF51A 51 56.7 62.7 1 1 82.4 2.4 JZ SMF54A 54 60 66.3 1 1 87.1 2.3 RE SMF58A 58 64.4 71.2 1 1 93.6 2.1 RG SMF60A 60 66.7 73.7 1 1 96.8 1.8 RK SMF64A 64 71.1 78.6 1 1 103 1.7 RM SMF70A 70 77.8 86 1 1 113 1.5 RP SMF75A 75 83.3 92.1 1 1 121 1.4 RR SMF78A 78 86.7 95.8 1 1 126 1.4 RT SMF85A 85 94.4 104 1 1 137 1.3 RV SMF90A 90 100 111 1 1 146 1.2 RX SMF100A 100 111 123 1 1 162 1.1 RZ SMF110A 110 122 135 1 1 177 1 SE SMF120A 120 133 147 1 1 193 0.9 SG SMF130A 130 144 159 1 1 209 0.8 SK SMF150A 150 167 185 1 1 243 0.7 SM SMF160A 160 178 197 1 1 259 0.7 SP SMF170A 170 189 209 1 1 275 0.6 SR SMF175A 175 198 214 1 1 284 0.6 S5 March 9,2018-REV.12 PAGE . 2 P PPM ,PEAK PULSE FORWARD ,KW SMF5.0A~SMF175A 100 Non-Repetitve Pulse Waveform Shown in Figure.3 T A = 25 OC 10 1.0 0.1 0.1 10 1.0 100 1000 10000 PEAK PULSE FORWARD (P PP) OR CURRENT (I PP) DERATING IN PERCENTAGE % 100 75 50 25 0 0 25 td ,PULSE WIDTH, micro sec 75 100 125 150 175 200 T A ,AMBIENT TEMPERATURE, OC Fig.1 PEAK PULSE POWER RATING CURVE Fig.2 DERATING CURVE 10,000 150 I PPM ,PEAK PULSE CURRENT,% 50 O tf = 10usec Ha lf Va lue -Ip p 2 10/1000 msec Waveform as Defined by R.E.A. 50 e -kt td 0 0 1.0 2.0 3.0 4.0 CJ , CAPACITANCE , pF Peak Value Ippm 100 T J = 25 C f= 1.0MHZ Vsig = 50mVp -p O T A = 25 C Pulse Width (td) is Defined as the Point where the Peak Current Decayst to 50% of Ipp 1,000 Mea sured a t Ze ro Bia s 100 Me a sure d a t Sta nd -Off Volta ge (VRWM) T,TIME,ms Fig.3 PULSE WAVEFORM I FSM , PEAK FORWARD SURGE CURRENT, AMPERES 10 1.0 2.0 5.0 10 20 50 100 200 50 V(RWM) , REVERSE STAND-OFF VOLTAGE , VOLTS T J=T J MAX 8.3ms Single Half Sine-Wave JEDEC Method 40 Fig.4 TYPICAL JUNCTION CAPACITANCE 30 20 10 0 1 2 4 10 20 40 100 NUMBER OF CYCLES AT 60Hz Fig.5 MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT March 9,2018-REV.12 PAGE . 3 SMF5.0A~SMF175A PART NO PACKING CODE VERSION Part No Packing Code Package Type Packing Type Marking Version SMF5.0A_R1_00001 SOD-123FL 3K / 7" Reel HE Halogen free MOUNTING PAD LAYOUT SOD-123FL Unit：inch(mm) 0.167 (4.25) 0.048 (1.22) 0.122 (3.10) 0.045 (1.15) March 9,2018-REV.12 PAGE . 4 SMF5.0A~SMF175A Disclaimer • Reproducing and modifying information of the document is prohibited without permission from Panjit International Inc.. • Panjit International Inc. reserves the rights to make changes of the content herein the document anytime without notification. Please refer to our website for the latest document. • Panjit International Inc. disclaims any and all liability arising out of the application or use of any product including damages incidentally and consequentially occurred. • Panjit International Inc. does not assume any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. • Applications shown on the herein document are examples of standard use and operation. Customers are responsible in comprehending the suitable use in particular applications. Panjit International Inc. makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. • The products shown herein are not designed and authorized for equipments requiring high level of reliability or relating to human life and for any applications concerning life-saving or life-sustaining, such as medical instruments, transportation equipment, aerospace machinery et cetera. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Panjit International Inc. for any damages resulting from such improper use or sale. • Since Panjit uses lot number as the tracking base, please provide the lot number for tracking when complaining. March 9,2018-REV.12 PAGE . 5