4140-52

Product Specification PE4140 Ultra-High Linearity UltraCMOS™ Broadband Quad MOSFET Array Product Description Features The PE4140 is an ultra-high linearity passive broadband Quad MOSFET array with high dynamic range performance capable of operation beyond 6.0 GHz. This quad array operates with differential signals at all ports (RF, LO, IF), allowing mixers to be built that use LO powers from -7 dBm to +20 dBm. Typical applications range from frequency up/down-conversion to phase detection for Cellular/PCS Base Stations, Wireless Broadband Communications and STB/Cable modems.  Ultimate Quad MOSFET array  Ultra-high linearity, broadband performance beyond 6.0 GHz  Ideal for mixer applications  Up/down conversion  Low conversion loss The PE4140 is manufactured on pSemi’s UltraCMOS™ process, a patented variation of silicon-on-insulator (SOI) technology on a sapphire substrate, offering the performance of GaAs with the economy and integration of conventional CMOS. Figure 1. Functional Diagram  High LO Isolation  Packaged in small 6-lead 3x3 mm DFN Figure 2. Package Type 6-lead DFN Table 1. AC and DC Electrical Specifications @ +25 °C Symbol Characteristics Test Conditions FTYP Operating Frequency Range1 VDS Drain-Source Voltage VDS Match Drain-Source Voltage Match VT Threshold Voltage VDS = 0.1V; per ASTM F617-00 R DS Drain-Source ‘ON’ Resistance VGS = +3V, IDS = 40 mA Min Typ Max Units 6.0 GHz 320 380 mV 12 40 mV DC VGS = +3V, IDS = 40 mA 260 -100 6.5 7.75 mV 9.5 Ω Note 1: Typical untested operating frequency range of Quad MOSFET transistors. Document No. DOC-87599-3 │ www.psemi.com ©2018-2020 pSemi Corp. All rights reserved. Page 1 of 10 PE4140 Product Specification Figure 3. Pin Configuration (Top View) Electrostatic Discharge (ESD) Precautions This MOSFET device has minimally protected inputs and is highly susceptible to ESD damage. When handling this UltraCMOS™ device, observe the same precautions that you would use with other ESD-sensitive devices. Latch-Up Avoidance Unlike conventional CMOS devices, UltraCMOS™ devices are immune to latch-up. Device Description The PE4140 passive broadband Quad MOSFET array is designed for use in up-conversion and down-conversion applications for high performance systems such as cellular infrastructure equipment and STB/CATV systems. Table 2. Pin Descriptions Pin No. Pin Name 1 IF1 IF Output Connection (Drain) 2 RF1 RF Input Connection (Source) 3 RF2 RF Input Connection (Source) 4 LO2 LO Input Connection (Gate) 5 LO1 LO Input Connection (Gate) 6 IF2 IF Output Connection (Drain) Description The PE4140 is an ideal mixer core for a wide range of mixer products, including module level solutions that incorporate baluns or other singleended matching structures enabling three-port operation. The performance level of this passive mixer is made possible by the very high linearity afforded by pSemi’s UltraCMOS™ process. Table 3. Absolute Maximum Ratings Parameters/ Conditions Min Max Units TST Storage temperature range -65 150 °C TOP Operating temperature range -40 85 °C Symbol VDC + AC Maximum DC plus peak AC voltage across DrainSource ±3.3 V VDC+AC Maximum DC plus peak AC voltage across GateDrain or Gate-Source ±4.2 V HBM1 ESD Voltage 100 V VESD Marking Packaged devices are marked with part number “4140”, date code and lot code. Moisture Sensitivity Level The Moisture Sensitivity Level rating for the PE4140 in the 6-lead 3x3 DFN package is MSL1. Note 1: ML_STD 883 Method 3015.7 Exceeding absolute maximum ratings may cause permanent damage. Operation should be restricted to the limits in the Operating Ranges table. Operation between operating range maximum and absolute maximum for extended periods may reduce reliability. ©2018-2020 pSemi Corp. All rights reserved. Page 2 of 10 Document No. DOC-87599-3 │ UltraCMOS™ RFIC Solutions PE4140 Product Specification Evaluation Kit Figure 4. Evaluation Board Layout pSemi Specification 101/0090 Applications Support If you have a problem with your evaluation kit or if you have applications questions, please contact applications support: E-Mail: help@psemi.com (fastest response) Phone: (858) 731-9400 Figure 5. Evaluation Board Schematic pSemi Specification 102/0115 Note: This is the complete evaluation board schematic; which can be used for multiple configurations. Not all components need be populated. Refer to 'typical schematics' on following pages. Document No. DOC-87599-3 │ www.psemi.com ©2018-2020 pSemi Corp. All rights reserved. Page 3 of 10 PE4140 Product Specification Figure 6. Typical Schematic for a PCS Application Table 4. Typical Performance in a PCS Application @ +25 °C Parameter Minimum Typical Maximum Units LO 1630 -- 2130 MHz RF 1700 -- 2200 MHz Frequency Range** 70 MHz 8.5 dB LO-RF 36 dB LO-IF 26 dB Input IP3** 32 dBm Input 1 dB Compression** 22 dBm IF Conversion Loss** (Includes balun losses) Isolation** ** Data taken on an Evaluation Board narrow-band tuned to cover the PCS band, IF = 73MHz low-side, LO drive = 17dBm. ©2018-2020 pSemi Corp. All rights reserved. Page 4 of 10 Document No. DOC-87599-3 │ UltraCMOS™ RFIC Solutions PE4140 Product Specification Typical Performance Plots in a PCS Application @ +25 °C (LO=17 dBm, IF=73 MHz Low-side) Figure 7. IIP3 vs. Frequency Figure 8. Conversion Loss vs. Frequency Figure 9. LO-RF & LO-IF Isolation Document No. DOC-87599-3 │ www.psemi.com ©2018-2020 pSemi Corp. All rights reserved. Page 5 of 10 PE4140 Product Specification Figure 10. Typical Schematic for a CATV Application (Reference Designators Refer to locations on Evaluation Board: 101/0090) J3 LO Input 1 4.7nH L1 ETC1.6-4-2-3 4 T1 3 U1 4 5 6 2 5 ETC1.6-4-2-3 T 2 1 5 1 3 2 1 3 2 J4 1 2 RF Input MLP6-3X3 L2 4.7nH R16 3.0pF 3 4 1 (Cut short between pads) 5 4 T3 ETC1-1-13 1 J6 IF Out Note: L1 and L2 provide LO port matching for optimum performance. Typical gate capacitance is approximately 2.5 pF. Table 5. Typical Performance in a CATV Application @ +25 °C Parameter Minimum Typical Maximum Units LO 1116 -- 1926 MHz RF 54 -- 864 MHz Frequency Range** 1062 MHz 6.5 dB LO-RF 40 dB LO-IF 28 dB Input IP3** 23 dBm Input 1 dB Compression** 13 dBm IF Conversion Loss** (Includes balun losses) Isolation** ** Data taken on an Evaluation Board tuned for a broadband CATV application, IF = 1062 MHz, RF drive = -5 dBm, LO drive = 10 dBm. ©2018-2020 pSemi Corp. All rights reserved. Page 6 of 10 Document No. DOC-87599-3 │ UltraCMOS™ RFIC Solutions PE4140 Product Specification Typical Performance Plots in a CATV Application @ +25 °C Figure 11. IIP3 vs. Frequency Figure 12. Conversion Loss vs. Frequency Figure 13. LO-RF & LO-IF Isolation Document No. DOC-87599-3 │ www.psemi.com ©2018-2020 pSemi Corp. All rights reserved. Page 7 of 10 PE4140 Product Specification Figure 14. Package Drawing 06L SLP (3x3mm) 6-lead DFN NOTE: The exposed solder pad (on the bottom of the package) is not electrically connected to any other pin (isolated). Figure 15. Marking Specifications ©2018-2020 pSemi Corp. All rights reserved. Page 8 of 10 Document No. DOC-87599-3 │ UltraCMOS™ RFIC Solutions PE4140 Product Specification Figure 16. Tape and Reel Specifications 6-lead DFN Tape Feed Direction Table 6. Dimensions Dimension DFN 3x3 mm Ao 3.23 ± 0.1 Bo 3.17 ± 0.1 Ko 1.37 ± 0.1 P 4 ± 0.1 W 8 +0.3, -0.1 T 0.254 ± 0.02 R7 Quantity 3000 R13 Quantity N.A. Note: R7 = 7 inch Lock Reel, R13 = 13 inch Lock Reel Document No. DOC-87599-3 │ www.psemi.com ©2018-2020 pSemi Corp. All rights reserved. Page 9 of 10 PE4140 Product Specification Table 7. Ordering Infomation Order Code Part Marking Description Package Shipping Method PE4140B-Z 4140 PE4140G-06DFN 3x3mm-3000C Green 6-lead 3x3 mm DFN 3000 units / T&R EK4140-01 PE4140-EK PE4140-06DFN 3x3mm-EK Evaluation Kit 1 / Box Sales Contact and Information For additional information, contact Sales at sales@psemi.com. ©2018-2020 pSemi Corp. All rights reserved. Page 10 of 10 Document No. DOC-87599-3 │ UltraCMOS™ RFIC Solutions