4141-52

Product Specification PE4141 Ultra-linear UltraCMOS™ Broadband Quad MOSFET Array Product Description Features  Ultimate Quad MOSFET array The PE4141 is an ultra-high linearity passive broadband Quad MOSFET array with high dynamic range performance capable of operation up to 1.0 GHz. This quad array operates with differential signals at all ports (RF, LO, IF), allowing an analog multiplexer to be built that uses LO ports as digital controls, RF and IF port as single-ended or differential inputs/outputs. The PE4141 switches the differential input to the differential output at the LO switching rate. Packaged in an 8-lead MSOP package, the PE4141 is ideal for highly magnetic environments such as Magnetic Resonance Imaging (MRI).  Very high linearity  Low magnetic  Ideal for mixer applications  Up/down conversion  Low conversion loss  High LO Isolation  8-lead MSOP package ideal for magnetic environments The PE4141 is manufactured on Peregrine’s UltraCMOS™ process, a patented variation of silicon-on-insulator (SOI) technology on a sapphire substrate, offering the performance of GaAs with the economy and integration of conventional CMOS. Applications The PE4141 is ideally suited for broadband analog multiplexer design in:  Medical instrumentation  Magnetic Resonance Imaging (MRI)  Data acquisition and ADC/DAC Figure 1. Functional Diagram muxing  RF modulation/demodulation  Precision instrumentation  Analog or digital video switch matrices LO2 LO1 IF1 IF2 Figure 2. Package Type 8-lead MSOP RF1 RF2 Table 1. AC and DC Electrical Specifications @ +25 °C Symbol Characteristics Test Conditions 1 FTYP Operating Frequency Range VDS Drain-Source Voltage VDS Match Drain-Source Voltage Match VT Threshold Voltage VDS = 0.1V; per ASTM F617-00 R DS Drain-Source ‘ON’ Resistance VGS = +3V, IDS = 40 mA Min Typ Max Units 1.0 GHz 320 380 mV 12 40 mV DC VGS = +3V, IDS = 40 mA 260 mV -100 6.5 7.75 9.5 Ω Note: 1. Typical untested operating frequency range of Quad MOSFET transistors. Document No. DOC-86561-2 │ www.psemi.com ©2018 Peregrine Semiconductor Corp. All rights reserved. Page 1 of 5 PE4141 Product Specification Electrostatic Discharge (ESD) Precautions Figure 3. Pin Configuration (Top View) IF1 1 8 IF2 GND 2 7 GND This MOSFET device has minimally protected inputs and is highly susceptible to ESD damage. When handling this UltraCMOS™ device, observe the same precautions that you would use with other ESD-sensitive devices. 6 LO1 Latch-Up Avoidance 4141 RF1 RF2 3 4 5 Unlike conventional CMOS devices, UltraCMOS™ devices are immune to latch-up. LO2 Device Description Table 2. Pin Descriptions Pin No. Pin Name The performance level of this MOSFET array is made possible by the very high linearity afforded by Peregrine’s UltraCMOS™ process. The 8-lead MSOP package is suitable for highly magnetic applications including Magnetic Resonance Imaging (MRI.) Description 1 IF1 2 GND IF Output Connection (Drain) Ground 3 RF1 RF Input Connection (Source) 4 RF2 RF Input Connection (Source) 5 LO2 LO Input Connection (Gate) 6 LO1 LO Input Connection (Gate) 7 GND Ground 8 IF2 The PE4141 is an ideal MOSFET array core for a wide range of MOSFET array products, including module level solutions that incorporate baluns or other single-ended matching structures enabling three-port operation. IF Output Connection (Drain) Table 3. Absolute Maximum Ratings Symbol Parameters/ Conditions TST Storage temperature range TOP Operating temperature range Min Max Units Marking -65 150 °C 0 70 °C VDC + AC Maximum DC plus peak AC voltage across DrainSource ±3.3 V VDC+AC Maximum DC plus peak AC voltage across GateDrain or Gate-Source ±4.2 V ESD Sensitive Device 100 V VESD Packaged devices are marked with part number “4141”, date code and lot code. Exceeding absolute maximum ratings may cause permanent damage. Operation should be restricted to the limits in the Operating Ranges table. Operation between operating range maximum and absolute maximum for extended periods may reduce reliability. ©2018 Peregrine Semiconductor Corp. All rights reserved. Page 2 of 5 Document No. DOC-86561-2 │ UltraCMOS™ RFIC Solutions PE4141 Product Specification Evaluation Kit Figure 4. Evaluation Board Layout Peregrine Specification 101-0157-02 Figure 5. Evaluation Board Schematic Peregrine Specification 102-0512-02 Document No. DOC-86561-2 │ www.psemi.com ©2018 Peregrine Semiconductor Corp. All rights reserved. Page 3 of 5 PE4141 Product Specification Figure 6. Package Drawing 8-lead MSOP TOP VIEW 0.65BSC .525BSC 7 8 6 12o REF 5 R 0.90 MIN 2.45±0.10 2X R 0.90 MIN GAGE PLANE 3.00±0.10 0o 0.25 6o 12o REF 0.55 ±0.15 0.51±0.13 -B- 0.51±0.13 1 2 3 4 2.95±0.10 .25 0.95 BSC A B C -C0.86±0.08 2.95±0.10 1.10 MAX -A0.10 +0.07 0.33 -0.08 A 0.08 0.10±0.05 A B C 3.00±0.10 4.90±0.15 3.00±0.10 FRONT VIEW ©2018 Peregrine Semiconductor Corp. All rights reserved. Page 4 of 5 SIDE VIEW Document No. DOC-86561-2 │ UltraCMOS™ RFIC Solutions PE4141 Product Specification Figure 7. Tape and Reel Specification 8-lead MSOP Table 4. Dimensions Dimension Ao Bo Ko F P1 W MSOP-8 5.30 ± 0.1 3.40 ± 0.1 1.40 ± 0.1 5.50 ± 0.05 8 ± 0.1 12 ± 0.3 Table 5. Ordering Information Order Codes 4141-52 PE4141B-W 4141-00 EK4141-02 Description PE4141 quad MOSFET array PE4141 quad MOSFET array PE4141 evaluation kit PE4141 evaluation kit Package Green 8-lead MSOP Green 8-lead MSOP Evaluation kit Evaluation kit Shipping Method 2000 units / T&R 2000 units / T&R 1 / Box 1 / Box Sales Contact and Information For additional information, contact Sales at sales@psemi.com. Advance Information: The product is in a formative or design stage. The datasheet contains design target specifications for product development. Specifications and features may change in any manner without notice. Preliminary Specification: The datasheet contains preliminary data. Additional data may be added at a later date. Peregrine reserves the right to change specifications at any time without notice in order to supply the best possible product. Product Specification: The datasheet contains final data. In the event Peregrine decides to change the specifications, Peregrine will notify customers of the intended changes by issuing a CNF (Customer Notification Form). The information in this document is believed to be reliable. However, Peregrine assumes no liability for the use of this information. Use shall be entirely at the user’s own risk. Document No. DOC-86561-2 │ www.psemi.com No patent rights or licenses to any circuits described in this datasheet are implied or granted to any third party. Peregrine’s products are not designed or intended for use in devices or systems intended for surgical implant, or in other applications intended to support or sustain life, or in any application in which the failure of the Peregrine product could create a situation in which personal injury or death might occur. Peregrine assumes no liability for damages, including consequential or incidental damages, arising out of the use of its products in such applications. Peregrine products are protected under one or more of the following U.S. patents: patents.psemi.com. ©2018 Peregrine Semiconductor Corp. All rights reserved. Page 5 of 5