0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
83502-00

83502-00

  • 厂商:

    PEREGRINE(游隼半导体)

  • 封装:

  • 描述:

    83502-00 - 3.5 GHz Low Power UltraCMOS Divide-by-4 Prescaler Military Operating Temperature Range - ...

  • 数据手册
  • 价格&库存
83502-00 数据手册
Product Specification PE83502 Product Description The PE83502 is a high-performance monolithic UltraCMOS™ prescaler with a fixed divide ratio of 4. Its operating frequency range is 1.5 GHz to 3.5 GHz. The PE83502 operates on a nominal 3 V supply and draws only 12 mA. It is packaged in a small 8-lead MSOP and is ideal for microwave PLL synthesis solutions. The PE83502 is manufactured on Peregrine’s UltraCMOS™ process, a patented variation of silicon-on-insulator (SOI) technology on a sapphire substrate, offering the performance of GaAs with the economy and integration of conventional CMOS. Figure 1. Functional Schematic Diagram 3.5 GHz Low Power UltraCMOS™ Divide-by-4 Prescaler Military Operating Temperature Range Features • High-frequency operation: 1.5 GHz to 3.5 GHz • Fixed divide ratio of 4 • Low-power operation: 12 mA typical @ 3 V across frequency • Small package: 8-lead MSOP • Low Cost Figure 2. Package Type 8-lead MSOP D IN Pre-Amp Q D Q OUT Output Buffer CLK QB CLK QB Table 1. Electrical Specifications (ZS = ZL = 50 Ω) 2.85 V ≤ VDD ≤ 3.15 V; -55° C ≤ TA ≤ 125° C, unless otherwise specified Parameter Supply Voltage Supply Current Input Frequency (FIN) Input Power (PIN) Conditions Minimum 2.85 Typical 3.0 13 Maximum 3.15 19 3.5 +10 +10 Units V mA GHz dBm dBm dBm 1.5 1500 MHz ≤ Fin ≤ 3200 MHz 3200 MHz < Fin ≤ 3500 MHz -5 0 -5 Output Power Document No. 70-0125-02 │ www.psemi.com ©2003-2006 Peregrine Semiconductor Corp. All rights reserved. Page 1 of 8 PE83502 Product Specification Figure 3. Pin Configuration (Top View) Electrostatic Discharge (ESD) Precautions When handling this UltraCMOS™ device, observe the same precautions that you would use with other ESD-sensitive devices. Although this device contains circuitry to protect it from damage due to ESD, precautions should be taken to avoid exceeding the rating specified in Table 3. Latch-Up Avoidance Unlike conventional CMOS devices, UltraCMOS™ devices are immune to latch-up. VDD 1 8 GND IN 2 7 OUT PE83502 DEC 3 6 GND GND 4 5 GND Table 2. Pin Descriptions Pin No. 1 2 Pin Name VDD IN Description Power supply pin. Bypassing is required. Input signal pin. Should be coupled with a capacitor (eg 15 pF) Power supply decoupling pin. Place a capacitor as close as possible and connect directly to the ground plane (eg 10 nF and 10 pF). Ground pin. Ground pattern on the board should be as wide as possible to reduce ground impedance. Ground pin. Ground pin. Divided frequency output pin. This pin should be coupled with a capacitor (eg 100 pF). Ground pin. Device Functional Considerations The PE83502 takes an input signal frequency from 1.5 GHz to 3.5 GHz and produces an output signal frequency one-fourth that of the supplied input. In order for the prescaler to work properly, several conditions need to be adhered to. It is crucial that pin 3 be supplied with a bypass capacitor to ground. In addition, the input and output signals (pins 2 & 7, respectively) need to be AC coupled via an external capacitor as shown in the test circuit in Figure 4. The ground pattern on the board should be made as wide as possible to minimize ground impedance. 3 DEC 4 5 6 7 8 GND GND GND OUT GND Table 3. Absolute Maximum Ratings Symbol VDD TST TOP VESD PINMAX Parameter/Conditions Supply voltage Storage temperature range Operating temperature range ESD voltage (Human Body Model) Maximum input power Min Max 4.0 Units V °C °C V dBm -65 -55 150 125 250 15 Absolute Maximum Ratings are those values listed in the above table. Exceeding these values may cause permanent device damage. Exposure to absolute maximum ratings for extended periods may affect device reliability. ©2003-2006 Peregrine Semiconductor Corp. All rights reserved. Page 2 of 8 Document No. 70-0125-02 │ U ltraCMOS™ RFIC Solutions PE83502 Product Specification Figure 4. Test Circuit Block Diagram VDD 3 V +/- 0.15 V + - 10 pF 1000 pF 1 8 7 100 pF 50 Ω Spectrum Analyzer 50 Ω 15 pF 2 PE83502 3 Signal Generator 4 5 6 10 nF 10 pF Figure 5. High Frequency System Application The wideband frequency of operation of the PE83502 makes it an ideal part for use in a DBS downconverter system. INPUT FROM DBS 1ST IF BPF SAW AGC FM DEMOD BASEBAND OUTPUT DIVIDE-BY-4 PE3293 PE83502 LOW NOISE PLL SYNTH LPF Document No. 70-0125-02 │ www.psemi.com ©2003-2006 Peregrine Semiconductor Corp. All rights reserved. Page 3 of 8 PE83502 Product Specification Typical Performance Data: VDD = 3.0 V Figure 6. Input Sensitivity Figure 7. Device Current Figure 8. Output Power ©2003-2006 Peregrine Semiconductor Corp. All rights reserved. Page 4 of 8 Document No. 70-0125-02 │ U ltraCMOS™ RFIC Solutions PE83502 Product Specification Evaluation Kit Evaluation Kit Operation The MSOP Prescaler Evaluation Board was designed to help customers evaluate the PE83502 Divide-by-4 Prescaler. On this board, the device input (pin 2) is connected to connector J1 through a 50 Ω transmission line. A series capacitor (C3) provides the necessary DC block for the device input. It is important to note that the value of this capacitance will impact the performance of the device. A value of 15pF was found to be optimal for this board layout; other applications may require a different value. The device output (pin 7) is connected to connector J3 through a 50 Ω transmission line. A series capacitor (C1) provides the necessary DC block for the device output. Note that this capacitor must be chosen to have a low impedance at the desired output frequency the device. The value of 100pF was chosen to provide a wide operating range for the evaluation board. The board is constructed of a two-layer FR4 material with a total thickness of 0.031”. The bottom layer provides ground for the RF transmission lines. The transmission lines were designed using a coplanar waveguide above ground plane model with trace width of 0.030”, trace gaps of 0.007”, dielectric thickness of 0.028”, metal thickness of 0.0014” and εr of 4.4. Note that the predominate mode for these transmission lines is coplanar waveguide. J2 provides DC power to the device. Starting from the lower left pin, the second pin to the right (J2-3) is connected to the device VDD pin (1). Two decoupling capacitors (10 pF, 1000 pF) are included on this trace. It is the responsibility of the customer to determine proper supply decoupling for their design application. The DEC pin (3) must be connected to a low impedance AC ground for proper device operation. On the board, two decoupling capacitors (C6 = 10 nF, C4 = 10 pF), located on the back of the board, perform this function. Applications Support If you have a problem with your evaluation kit or if you have applications questions call (858) 731-9400 and ask for applications support. You may also contact us by fax or e-mail: Fax: (858) 731-9499 E-Mail: help@psemi.com Figure 9. Evaluation Board Layouts Peregrine Specification 101/0035 Figure 10. Evaluation Board Schematic Peregrine Specification 102/0200 Document No. 70-0125-02 │ www.psemi.com ©2003-2006 Peregrine Semiconductor Corp. All rights reserved. Page 5 of 8 PE83502 Product Specification Figure 11. Package Drawing 8-lead MSOP TOP VIEW 0.65BSC 8 7 6 5 .525BSC 2.45±0.10 2X 3.00±0.10 0.51±0.13 -B1 2 3 4 .25 A B C 0.51±0.13 2.95±0.10 -C0.86±0.08 2.95±0.10 1.10 MAX -A0.10 A 0.33+0.07 -0.08 0.08 ABC 3.00±0.10 FRONT VIEW SIDE VIEW 0.10±0.05 3.00±0.10 4.90±0.15 ©2003-2006 Peregrine Semiconductor Corp. All rights reserved. Page 6 of 8 Document No. 70-0125-02 │ U ltraCMOS™ RFIC Solutions PE83502 Product Specification Figure 12. Tape and Reel Specifications 8-lead MSOP Pin1 Table 4. Ordering Information Order Code 83502-21 83502-22 83502-00 Part Marking 83502 83502 PE83502-EK Description PE83502-08MSOP-100A PE83502-08MSOP-2000C PE83502-08MSOP-EK Package 8-lead MSOP 8-lead MSOP Evaluation Board Shipping Method 50 pcs. / Tube 2000 pcs. / T&R 1 / Box Document No. 70-0125-02 │ www.psemi.com ©2003-2006 Peregrine Semiconductor Corp. All rights reserved. Page 7 of 8 PE83502 Product Specification Sales Offices The Americas Peregrine Semiconductor Corporation 9450 Carroll Park Drive San Diego, CA 92121 Tel: 858-731-9400 Fax: 858-731-9499 North Asia Pacific Peregrine Semiconductor K.K. Teikoku Hotel Tower 10B-6 1-1-1 Uchisaiwai-cho, Chiyoda-ku Tokyo 100-0011 Japan Tel: +81-3-3502-5211 Fax: +81-3-3502-5213 Europe Peregrine Semiconductor Europe Bâtiment Maine 13-15 rue des Quatre Vents F-92380 Garches, France Tel: +33-1-4741-9173 Fax : +33-1-4741-9173 Peregrine Semiconductor, Korea #B-2402, Kolon Tripolis, #210 Geumgok-dong, Bundang-gu, Seongnam-si Gyeonggi-do, 463-480 S. Korea Tel: +82-31-728-4300 Fax: +82-31-728-4305 South Asia Pacific Peregrine Semiconductor, China Shanghai, 200040, P.R. China Tel: +86-21-5836-8276 Fax: +86-21-5836-7652 Space and Defense Products Americas: Tel: 858-731-9453 Europe, Asia Pacific: 180 Rue Jean de Guiramand 13852 Aix-En-Provence Cedex 3, France Tel: +33-4-4239-3361 Fax: +33-4-4239-7227 For a list of representatives in your area, please refer to our Web site at: www.psemi.com Data Sheet Identification Advance Information The product is in a formative or design stage. The data sheet contains design target specifications for product development. Specifications and features may change in any manner without notice. The information in this data sheet is believed to be reliable. However, Peregrine assumes no liability for the use of this information. Use shall be entirely at the user’s own risk. No patent rights or licenses to any circuits described in this data sheet are implied or granted to any third party. Peregrine’s products are not designed or intended for use in devices or systems intended for surgical implant, or in other applications intended to support or sustain life, or in any application in which the failure of the Peregrine product could create a situation in which personal injury or death might occur. Peregrine assumes no liability for damages, including consequential or incidental damages, arising out of the use of its products in such applications. The Peregrine name, logo, and UTSi are registered trademarks and UltraCMOS and HaRP are trademarks of Peregrine Semiconductor Corp. Preliminary Specification The data sheet contains preliminary data. Additional data may be added at a later date. Peregrine reserves the right to change specifications at any time without notice in order to supply the best possible product. Product Specification The data sheet contains final data. In the event Peregrine decides to change the specifications, Peregrine will notify customers of the intended changes by issuing a DCN (Document Change Notice). ©2003-2006 Peregrine Semiconductor Corp. All rights reserved. Page 8 of 8 Document No. 70-0125-02 │ U ltraCMOS™ RFIC Solutions
83502-00 价格&库存

很抱歉,暂时无法提供与“83502-00”相匹配的价格&库存,您可以联系我们找货

免费人工找货