84140-00

Product Specification PE84140 Product Description The PE84140 is an ultra-high linearity, passive broadband Quad MOSFET array with high dynamic range performance capable of operation beyond 6.0 GHz. This quad array operates with differential signals at all ports (RF, LO, IF), allowing mixers to be built that use LO powers from -7 dBm to +20 dBm. Typical applications range from frequency up/downconversion to phase detection for Cellular/PCS Base Stations, Wireless Broadband Communications and STB/Cable modems. The PE84140 is optimized for stringent military applications. It is manufactured on Peregrine’s UltraCMOS™ process, a patented variation of silicon-on-insulator (SOI) technology on a sapphire substrate, offering the performance of GaAs with the economy and integration of conventional CMOS. Ultra-High Linearity UltraCMOS™ Broadband Quad MOSFET Array Features • Ultimate Quad MOSFET array • Ultra-high linearity, broadband performance beyond 6.0 GHz • Ideal for mixer applications • Up/down conversion • Low conversion loss • High LO Isolation • Optimized for stringent military applications Figure 1. Functional Diagram Figure 2. Package Type 8-lead MSOP LO IF RF Table 1. AC and DC Electrical Specifications @ +25 °C Symbol FTYP VDS VDS M atch VT R DS Characteristics Operating Frequency Range Drain-Source Voltage Drain-Source Voltage Match Threshold Voltage Drain-Source ‘ON’ Resistance 1 Min DC Typ 6.0 330 20 -100 8.25 Max Units GHz mV mV mV Ω Test Conditions VGS = +3V, IDS = 40 mA VDS = 0.1V; per ASTM F617-00 VGS = +3V, IDS = 40 mA Note 1: Typical untested operating frequency range of Quad MOSFET transistors. Document No. 70-0127-02 │ www.psemi.com ©2003-2006 Peregrine Semiconductor Corp. All rights reserved. Page 1 of 7 PE84140 Product Specification Figure 3. Pin Configuration (Top View) LOM LOP GND IFP 1 2 8 7 RFM RFP GND IFM Electrostatic Discharge (ESD) Precautions This MOSFET device has minimally protected inputs and is highly susceptible to ESD damage. When handling this UltraCMOS™ device, observe the same precautions that you would use with other ESD-sensitive devices. Latch-Up Avoidance Unlike conventional CMOS devices, UltraCMOS™ devices are immune to latch-up. Device Description PE84140 3 4 6 5 Table 2. Pin Descriptions Pin No. 1 2 3 4 5 6 7 8 Pin Name LOM LOP GND IFP IFM GND RFP RFM Description LO Input Connection (Gate) LO Input Connection (Gate) Ground Connection IF Output Connection (Drain) IF Output Connection (Drain) Ground Connection RF Input Connection (Source) RF Input Connection (Source) The PE84140 passive broadband Quad MOSFET array is designed for use in up-conversion and down-conversion applications for high performance systems. The PE84140 is an ideal mixer core for a wide range of mixer products, including module level solutions that incorporate baluns or other singleended matching structures enabling three-port operation. The performance level of this passive mixer is made possible by the very high linearity afforded by Peregrine’s UltraCMOS™ process. Table 3. Absolute Maximum Ratings Symbol TST TOP Parameter/Conditions Storage temperature range Operating temperature range Maximum DC plus peak AC voltage across DrainSource Maximum DC plus peak AC voltage across GateDrain or Gate-Source ESD Sensitive Device Min -65 -55 Max 150 125 Units °C °C VDC + AC ±3.3 V VDC+AC VESD ±4.2 250 V V Absolute Maximum Ratings are those values listed in the above table. Exceeding these values may cause permanent device damage. Functional operation should be restricted to the limits in the DC Electrical Specifications table. Exposure to absolute maximum ratings for extended periods may affect device reliability. ©2003-2006 Peregrine Semiconductor Corp. All rights reserved. Page 2 of 7 Document No. 70-0127-02 │ U ltraCMOS™ RFIC Solutions PE84140 Product Specification Evaluation Kit Figure 4. Evaluation Board Layout Peregrine Specification 101/0157 Applications Support If you have a problem with your evaluation kit or if you have applications questions, please contact applications support: E-Mail: help@psemi.com (fastest response) Phone: (858) 731-9400 Figure 5. Evaluation Board Schematic Peregrine Specification 102/0214 Note: This is the complete evaluation board schematic; which can be used for multiple configurations. Not all components need be populated. Refer to the typical schematic on the following page. Document No. 70-0127-02 │ www.psemi.com ©2003-2006 Peregrine Semiconductor Corp. All rights reserved. Page 3 of 7 PE84140 Product Specification Figure 6. Typical Schematic ©2003-2006 Peregrine Semiconductor Corp. All rights reserved. Page 4 of 7 Document No. 70-0127-02 │ U ltraCMOS™ RFIC Solutions PE84140 Product Specification Figure 7. Package Drawing 8-lead MSOP TOP VIEW 0.65BSC 8 7 6 5 .525BSC 12o REF 2.45±0.10 2X 3.00±0.10 GAGE PLANE 0.25 12o REF R 0.90 MIN R 0.90 MIN 0o 6o 0.55 ±0.15 0.95 BSC 0.51±0.13 -B1 2 3 4 .25 A B C 0.51±0.13 2.95±0.10 -C0.86±0.08 2.95±0.10 1.10 MAX -A0.10 A 0.33+0.07 -0.08 0.08 ABC 3.00±0.10 FRONT VIEW SIDE VIEW 0.10±0.05 3.00±0.10 4.90±0.15 Document No. 70-0127-02 │ www.psemi.com ©2003-2006 Peregrine Semiconductor Corp. All rights reserved. Page 5 of 7 PE84140 Product Specification Figure 8. Tape and Reel Specifications 8-lead MSOP Pin1 Table 7. Ordering Information Order Code 84140-01 84140-02 84140-00 Part Marking 84140 84140 PE84140-EK Description PE84140-08MSOP-50A PE84140-08MSOP-2000C PE84140-08MSOP-EK Package 8-lead MSOP 8-lead MSOP Evaluation Kit Shipping Method 50 units / Tube 2000 units / T&R 1 / Box ©2003-2006 Peregrine Semiconductor Corp. All rights reserved. Page 6 of 7 Document No. 70-0127-02 │ U ltraCMOS™ RFIC Solutions PE84140 Product Specification Sales Offices The Americas Peregrine Semiconductor Corporation 9450 Carroll Park Drive San Diego, CA 92121 Tel: 858-731-9400 Fax: 858-731-9499 North Asia Pacific Peregrine Semiconductor K.K. Teikoku Hotel Tower 10B-6 1-1-1 Uchisaiwai-cho, Chiyoda-ku Tokyo 100-0011 Japan Tel: +81-3-3502-5211 Fax: +81-3-3502-5213 Europe Peregrine Semiconductor Europe Bâtiment Maine 13-15 rue des Quatre Vents F-92380 Garches, France Tel: +33-1-4741-9173 Fax : +33-1-4741-9173 Peregrine Semiconductor, Korea #B-2402, Kolon Tripolis, #210 Geumgok-dong, Bundang-gu, Seongnam-si Gyeonggi-do, 463-480 S. Korea Tel: +82-31-728-4300 Fax: +82-31-728-4305 South Asia Pacific Peregrine Semiconductor, China Shanghai, 200040, P.R. China Tel: +86-21-5836-8276 Fax: +86-21-5836-7652 Space and Defense Products Americas: Tel: 858-731-9453 Europe, Asia Pacific: 180 Rue Jean de Guiramand 13852 Aix-En-Provence Cedex 3, France Tel: +33-4-4239-3361 Fax: +33-4-4239-7227 For a list of representatives in your area, please refer to our Web site at: www.psemi.com Data Sheet Identification Advance Information The product is in a formative or design stage. The data sheet contains design target specifications for product development. Specifications and features may change in any manner without notice. The information in this data sheet is believed to be reliable. However, Peregrine assumes no liability for the use of this information. Use shall be entirely at the user’s own risk. No patent rights or licenses to any circuits described in this data sheet are implied or granted to any third party. Peregrine’s products are not designed or intended for use in devices or systems intended for surgical implant, or in other applications intended to support or sustain life, or in any application in which the failure of the Peregrine product could create a situation in which personal injury or death might occur. Peregrine assumes no liability for damages, including consequential or incidental damages, arising out of the use of its products in such applications. The Peregrine name, logo, and UTSi are registered trademarks and UltraCMOS and HaRP are trademarks of Peregrine Semiconductor Corp. Preliminary Specification The data sheet contains preliminary data. Additional data may be added at a later date. Peregrine reserves the right to change specifications at any time without notice in order to supply the best possible product. Product Specification The data sheet contains final data. In the event Peregrine decides to change the specifications, Peregrine will notify customers of the intended changes by issuing a DCN (Document Change Notice). Document No. 70-0127-02 │ www.psemi.com ©2003-2006 Peregrine Semiconductor Corp. All rights reserved. Page 7 of 7