PI5V330SQEX

PI5V330S Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux Features Description • • • • • • • • • High-performance solution to switch between video sources Wide bandwidth: 570 MHz (typical) Low On-Resistance: 5Ω (typical) Low crosstalk at 10 MHz: –80dB Ultra-low quiescent power (0.1µA typical) Single supply operation: +5.0V Fast switching: 10ns ESD > 5KV HBM, 10KV I/O to GND Packaging (Pb-free & Green Available): – 16-pin 150-mil wide plastic SOIC (W) – 16-pin 150-mil wide plastic QSOP (Q) Pericom Semiconductor’s PI5V330S is a true bidirectional Quad 2-channel multiplexer/demultiplexer recommended for both RGB and composite video switching applications. The video switch can be driven from a current output RAMDAC or voltage output composite video source. Low On-Resistance and wide bandwidth make it ideal for video and other applications. Also this device has exceptionally high current capability which is far greater than most analog switches offered today. A single 5V supply is all that is required for operation. Block Diagram Pin Configuration S1A The PI5V330S offers a high-performance, low-cost solution to switch between video sources. The application section describes the PI5V330S replacing the HC4053 multiplier and buffer/amplifier. IN S1A DA S2A S2A S1B DA S1B DB S2B S1C S2B DC S2C S1D DB GND DD S2D DECODER/DRIVERS EN 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 VDD EN S1D S2D DD S1C S2C DC Pin Description Pin Name IN Truth Table S1A, S1B, S1C, S1D S2A, S2B, S2C, S2D Analog Video I/O IN Select Input EN Enable EN IN 0 0 S1A, S1B, S1C, S1D D A, D B DC, DD Analog Video I/O 0 1 S2A, S2B, GND Ground 1 X Disabled VDD Power 13-0016 ON Switch Description S2C, S2D 1 PS7032I 12/12/12 PI5V330S Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature...........................................................–65°C to +150°C Ambient Temperature with Power Applied..........................–40°C to +85°C Supply Voltage to Ground Potential (Inputs & VDD Only)...–0.5V to +7.0V Supply Voltage to Ground Potential (Outputs & D/O Only).–0.5V to +7.0V DC Input Voltage...................................................................–0.5V to +7.0V DC Output Current..............................................................................120mA Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Power Dissipation..................................................................................0.5W DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VDD = 5V ±5%) Parameters Description VANALOG Analog Signal Range VIH Input HIGH Voltage VIL Test Conditions(1) Min. Typ.(2) Max. 0 2.0 Guaranteed Logic HIGH Level 2.0 - Input LOW Voltage Guaranteed Logic LOW Level –0.5 0.8 IIH Input HIGH Current VDD = Max., VIN = VDD ±1 IIL Input LOW Current VDD = Max., VIN = GND ±1 IO Analog Output Leakage Current 0 ≤ S1, S2 or D ≤ VDD, Switch OFF ±1 VIK Clamp Diode Voltage VDD = Min., IIN = -18mA VH Input Hysteresis at Control Pins Switch On-Resistance(3) RON Notes: 1. 2. 3. -0.7 -1.2 Units V µA V 150 - VDD = Min., VIN = 1.0V, ION = 13mA 5 7 VDD = Min., VIN = 2.0V, ION = 26mA 7 mV Ω 10 For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. Typical values are at VDD = 5.0V, TA = 25°C ambient and maximum loading. Measured by the voltage drop between S1, S2, and D I/O pins at indicated current through the switch. On-Resistance is determined by the lower of the voltages on the S1, S2, and D I/O pins. 13-0016 2 PS7032I 12/12/12 PI5V330S Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux Dynamic Characteristics (Over the Operating Range, TA = –40°C to +85°C, VDD = 5V ±5%) Parameters Description Test Conditions Min. Typ. Max. tON Turn On Time RL = 75Ω, CL = 20PF, See Fig. 4 2.5 5 tOFF Turn Off Time 1.1 5 BW(1) RL = 75Ω, CL = 20PF, See Fig. 4 -3 dB Bandwidth See Fig. 5 XTALK Crosstalk 10MHz, See Fig. 5, CL = 0pF CIN Input/Enable Capacitance VIN = 0V, f = 1 MHz 6 COFF Capacitance, Switch Off VIN = 0V, f = 1 MHz 6 CON(1) Capacitance, Switch On VIN = 0V, f = 1 MHz 9 OIRR Off Isolation 10MHz, See Fig 5, CL = 0pF (1) (1) 570 -80 Unit ns MHz dB -48 pF dB Notes: 1. This parameter is determined by device characterization but is not production tested. Power Supply Characteristics Parameters Test Conditions(1) Description ICC Quiescent Power Supply Current VDD = Max. IN = GND or VDD ∆ICC Supply Current per Input @ TTL HIGH VDD = Max. IN = 3.4V(3) ICCD Supply Current per Input per MHz(4) VDD = Max., S1, S2 and D Pins Open EN = GND Control Input Toggling 50% Duty Cycle Min. Typ(2) Max. Units 0.1 3.0 µA 2.5 mA 0.25 mA/ MHz Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at VDD = 5.0V, +25°C ambient. 3. Per TTL driven input (VIN = 3.4V, control inputs only); S1, S2, and D pins do not contribute to ICC. 4. This current applies to the control inputs only and represent the current required to switch internal capacitance at the specified frequency. The S1, S2, and D I/O pins generate no significant AC or DC currents as they transition. This parameter is not tested, but is guaranteed by design. 13-0016 3 PS7032I 12/12/12 PI5V330S Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux Definitions Symbol Description RON Resistance between source and drain with switch in the ON state. IO Output leakage current measured at S1, S2, and D with the switch OFF. VIN Digital voltage at the IN pin that selects between S1 and S2 analog inputs. VEN A voltage that ENABLES the chip. CIN Capacitance at the digital inputs. COFF Capacitance at analog I/O (S1, S2, D) with switch OFF. CON Capacitance at analog I/O (S1, S2, D) with switch ON. VIH Minimum input voltage for logic HIGH. VIL Minimum input voltage for logic LOW. IIH (IIL) Input current of the digital input. tON Propagation delay measured between 50% of the digital input to 90% of the analog output when switch is turned ON. The peak analog voltage is 0.714V. tOFF Propagation delay measured between 50% of the digital input to 90% of the analog output when switch is turned OFF. The peak analog voltage is 0.714V. BW Frequency response of the switch in the ON state measured at 3dB down. XTALK Is an unwanted signal coupled from channel to channel. Measured in –dB. Xtalk = 20 LOG Vout/Vin. This is non-adjacent crosstalk. OIRR Off isolation is the resistance (measured in –dB) between the input and output with the switch off (NO). 13-0016 4 PS7032I 12/12/12 PI5V330S Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux Figure 1. Gain vs Frequency Figure 2. Off Isolation vs Frequency 13-0016 5 PS7032I 12/12/12 PI5V330S Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux Figure 3. Crosstalk vs Frequency +5.0V 3V S VDD D 75Ω 50% tOFF 20pF IN GND 50% Digital Input VOUT 90% Analog Output EN 90% tON Figure 4. Switching Time HP4396B S1 R1 T1 PI5V330S HP11667A Figure 5. Gain/Phase, Crosstalk, Off-Isolation 13-0016 6 PS7032I 12/12/12 DATE: 06/15 PI5V330S Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux Packaging Mechanical: 16-pin SOIC (W) DATE: 06/15/12 DESCRIPTION: 16-Pin, 150mil Wide SOIC PACKAGE CODE: W DOCUMENT CONTROL #: PD-1004 REVISION: F 2012-0398 13-0016 7 PS7032I 12/12/12 PI5V330S Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux Packaging Mechanical: 16-pin QSOP (Q) DOCUMENT CONTROL NO. PD - 1201 REVISION: G 16 .008 0.20 MIN. .150 .157 3.81 3.99 .008 .013 0.20 0.33 Guage Plane .010 0.254 1 DATE: 11/07/07 Detail A .189 .197 4.80 5.00 0˚-6˚ .016 .035 0.41 0.89 .041 1.04 REF .015 x 45° 0.38 1 .008 0.203 REF .053 1.35 .069 1.75 Detail A .007 0.178 .010 0.254 SEATING PLANE .025 BSC 0.635 .228 .244 5.79 6.19 .004 0.101 .010 0.254 .008 .012 0.203 0.305 X.XX DENOTES DIMENSIONS IN MILLIMETERS X.XX Note: 1) Controlling dimensions in inches. 2) Ref: JEDEC MO-137B/AB. 3) Dimensions do not include mold flash, protrusions or gate burrs Pericom Semiconductor Corporation 3545 N. 1st Street, San Jose, CA 95134 1-800-435-2335 • www.pericom.com DESCRIPTION: 16-Pin 150-Mil Wide QSOP PACKAGE CODE: Q Ordering Information Ordering Code Package Code Package Description PI5V330SWE W Pb-free & Green, 16-pin 150-mil wide plastic SOIC PI5V330SQE Q Pb-free & Green, 16-pin 150-mil wide plastic QSOP Notes: 1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ 2. E = Pb-free and Green 3. Adding an X suffix = Tape/Reel Pericom Semiconductor Corporation • 1-800-435-2336  •  www.pericom.com 13-0016 8 PS7032I 12/12/12