MVS-2600

DATASHEET Lighting Imaging Telecom Machine Vision Illumination Systems MVS-2600 Series Machine Vision Strobes Description The PerkinElmer MVS 2600 Series Machine Vision Strobe systems produce high intensity pulsed light for industrial vision applications. The light output of the strobe may be coupled directly to a fiber optic bundle, a slit projector, or an optical assembly to project light to an area remote from the instrument. When used with a CCD/CID camera system, the MVS 2600 Series strobes freeze motion, thereby eliminating blur and enhancing camera image quality. The MVS 2600 Series strobes consist of a power supply, a diode pac, a discharge board, and a Lite-Pac® containing a flashlamp. A nose piece and an adapter are used to interface fiber optic bundles to the flashlamp. A heat sink is used to secure the nose piece or a structured light assembly to the flashlamp. MVS 2600 Series strobe systems are available in configurations to satisfy various user requirements. The standard MVS 2601 operates up to 60 Hz. An MVS 2612 (400 Hz maximum) or MVS 2613 (1000 Hz maximum) are available at lower light output energies. The MVS 2611 produces 1 µ sec pulses at 1 kHz maximum. Features • Remote illumination via fiber bundles from flashlamp • Flash rates of 60, 400, and 1000 Hz • Microsecond flash durations • Long lamp life • Remote intensity control capability . www.perkinelmer.com/opto MVS-2600 Series Optical Specifications Spectral bandwidth (1) Flashlamp arc length Flash rate (2) Flashlamp life (4) Flash duration (2) (3) Flash to flash variation Light output (2) Note 1: Note 2: Note 3: Note 4: MVS-2600 Series 300 to 1100+ nm 0.06 in (1.5mm) 60 Hz maximum 108 flashes 6 microseconds typical 70% of initial intensity Environmental Specifications Operating temperature Storage temperature Shock and vibration -10 to +110°C (-23 to +43°F) -40 to +194°C (-40 to +90°F) 1.5 g. 5 to 20 Hz per MIL-STD 810C Electrical Specifications Type Line input voltage Input current Output voltage (1) Output power (2) Reference voltage (3) Tirgger input: (4) Trigger Pulse duration Note 1: Note 2: Note 3: Note 4: MVS-2601 115/230 ±10% VAC 50/60 Hz (115 factory set) 1.2 amps maximum (115 VAC) 225 to 750 volts 43 watts maximum 3 to 10VDC MVS-2602 15 to 28 VDC 4 amps peak at 24 VDC 200 to 750 volts 43 watts maximum 2 to 10 VDC +5 volt pulse into opto-isolator with 150 ohm nominal series resistor 10 to 100 microseconds Output measured @ front face of bulb. Up to 20 watts with heat sink and natural convection cooling. Above 20 watts forced air cooling is required. Output voltage may be adjusted using an external voltage reference source. MVS 2601, 75 volts per volt of reference. MVS 2602, 100 volts per volt of reference. Delay between flash command and light output is 8 microseconds typical. Mechanical Specifications MATING INPUT CONNECTOR(S) SUPPLIED 0.218 X 0.281 MOUNTING SLOT (4 PLCS) 8.50 (215.9) NEMA 13 ENCLOSURE WEIGHT 6.5 LBS (3.0 kg) DIMENSIONS ARE IN INCHES (MILLIMETERS) 7.00 (177.8) 4.12 (104.8) 4.25 (108.0) 9.25 (235.0) NOSEPIECE, BLANK ADAPTER AND HEAT SINK SUPPLIED WITH ALL MVS-2600 SERIES UNITS For more information e-mail us at opto@perkinelmer.com or visit our web site at www.perkinelmer.com/opto. All values are nominal; specifications subject to change without notice. USA: PerkinElmer Optoelectronics 35 Congress Street Salem, MA 01970 Toll Free: (800) 950-3441 (USA) Phone: (978) 745-3200 Fax: (978) 745-0894 © 2001 PerkinElmer inc. All rights reserved. Europe: PerkinElmer Optoelectronics Wenzel-Jaksch-Str. 31, D-65199 Weisbaden, Germany Phone: +49 (0) 611-492-437 Fax: +49 (0)611-492-159 Asia: PerkinElmer Optoelectronics 47 Ayer Rajah Crescent #06-12 Singapore 139947 Phone: +65 775 2022 Fax: +65 775 1008 . 0601 www.perkinelmer.com/opto