PE500C-13UV

DATASHEET Lighting Imaging Telecom Cermax® Xenon Arc Lamps PE500C-13F and PE500C-13UV CERMAX® FOCUSED XENON ARC LAMPS Description The Cermax® xenon arc lamp is an innovative lamp design in the specialty lighting industry. These lamps were introduced in the early 1980’s and are now used in endoscopes in most major hospitals worldwide, in high brightness projection display systems, and for a wide variety of other high performance applications. The PE500C-13F and PE500C-13UV Cermax® lamps have an integrated elliptical reflector, enabling high intensity, focused output of ultraviolet, visible, and infrared radiation. With their internal reflector and rugged ceramic body construction, Cermax® lamps are the safest and most compact alternative to conventional quartz xenon lamps. This makes them ideal for applications that require a high degree of illumination control. Current-regulated or power-regulated power supplies with output ripples of less than 5% are recommended. Single shot ignition pulses are advised because radio frequency starters may damage the lamps internal reflector. In addition to lamps, PerkinElmer Optoelectronics manufactures Cermax® arc lamp power supplies, lamp holders, OEM lighting systems, and fiber optic light sources. Applications • Medical and industrial fiber optic illu- • • • • • • minators Machine vision Infrared and visible spotlights/beacons Spectroscopy Microscopy UV Curing Video projection . www.perkinelmer.com/opto PE500C-13F and PE500C-13UV Operational Specifications Description Power Current Operating Voltage Ignition Voltage Temperature Lifetime* Nominal 500 watts 32 amps (DC) 15.5 volts (DC) 150º C (maximum) 1000 hours (500 hour warranty) Range 350-525 watts 25-35 amps (DC) 14-16,5 volts (DC) Physical Specifications Description Arc Gap Reflector Geometry Weight Window Diameter Specification .045 inch (1.14mm) Ellipsoidal 1= X2/M2 +Y2/N2 191 grams 1 inch (25.4 mm) 30 kilovolts (recommended minimum) Focused Output Description 6mm aperture 3mm aperture Visible Output* 7200 Lumens 3600 Lumens Total Output 70 watts 35 watts * End of lamp life is defined as 50% of initial output. Output at Nominal Power F= UV Filtered Output/ UV = UV Enhanced Output Description Radiant Output* UV Output* IR Output* Visible Output* Color Temperature Peak Instabilities PE500C-13F 112 watts 5 watts 65 watts 10500 Lumens 5900 Kelvin 4% PE500C-13UV 112 watts 10.3 watts 63 watts 9550 Lumens 5050 Kelvin 4% 0.7” at 50% pts .23” at 10% pts * Nominal values at 500 watts after 2 hour burn-in Notes 1. 2. 3. 4. Lamp must not be operated with window facing upwards within 45º of vertical. Seal temperature must not exceed 150º C. Current/power regulated power supplies and PerkinElmer lamp housing units are recommended. Lamp must be operated within recommended current and power range. Over powering may lead to arc instability, hard starting and premature aging. CERMAX lamps are much safer lamps to use than their quartz xenon arc lamp equivalents. However, caution must be practiced when operating lamps because they are under high pressure, require high voltage, reach temperatures up to 200º C, and their IR and UV radiation can cause skin burns and eye damage. Read hazard sheet included with each lamp shipment. Spot Size at Crossover .07” at 50% pts Spot Size at Crossover .23” at 10% pts *These values indicate total output in all directions. Wavelengths = UV770nm, Visible 390nm to 770nm. ** Beam Geometry defined as half angle at 10% PTS after 01/100/1000 hours. 5. Dimensions 1.00 (25.4) 1.298 (32.97) 1.67 (42.4) .241 (6.12) .259 (6.58) .75 (19.05) 1.00 (25.4) Spectral Output F UV F + HOT MIRROR 100 .25 (6.35) .40 (10.2) 2.17 (55.1) .666 (16.92) .008 (.203) .212 (5.39) .645 (16.4) .035 (.89) 1.750 (44.45) M=1.3647 N=0.731 RELATIVE OUTPUT 80 60 40 20 Focal Point Cathode C Ellipse L Refector Edge 0 200 300 400 500 600 700 800 900 1000 1100 WAVELENGTH (NM) Dimensions in parentheses are in millimeters PerkinElmer welcomes inquiries about special lamps. We would be pleased to discuss the requirements of your application and the feasibility of designing a lamp specifically suited to your needs. For more information e-mail us at opto@perkinelmer.com or visit our web site at www.perkinelmer.com/opto. All values are nominal; specifications subject to change without notice. USA: PerkinElmer Optoelectronics 44370 Christy St. Fremont, CA 94538 Phone: (510) 979-6500 Fax: (510) 687-1140 Toll Free: (800) 775-6786 Europe: PerkinElmer Optoelectronics GmbH Wenzel-Jaksch-Str. 31 65199 Wiesbaden Germany Phone: +49 611 492 0 Fax: +49 611 492 369 Asia: PerkinElmer Optoelectronics 47 Ayer Rajah Crescent #06-12 Singapore 139947 Phone: +65 775 2022 Fax: +65 775 1008 . © 2000 PerkinElmer inc. All rights reserved. DS-169 Rev C 1101 www.perkinelmer.com/opto