FR201

FAST RECOVERY RECTIFIER FR201 THRU FR207 VOLTAGE CURRENT RANGE 50 to 1000 Volts 2.0 Ampere FEATURES
Low cost construction.
Fast switching for high efficiency.
Low reverse leakage
High forward surge current capability.
High temperature soldering guaranteed: 260/10 seconds, 0.375" (9.5mm)lead length at 5 lbs (2.3kg) tension. MECHANICAL DATA
Case: transfer molded plastic
Epoxy: UL94V - 0 rate flame retardant.
Polarity: Color band denotes cathode end.
Lead: Plated axial lead, solderable per MIL - STD - 202E method 208C
Mounting position: Any
Weight: 0.014 ounce, 0.39grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25 ambient temperature unless otherwise specified
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive load derate current by 20% SYMBOLS FR201 FR202 VRRM 50 100 VRMS 35 70 VDC 50 100 I(AV) FR203 200 140 200 FR204 400 280 400        150 25 40 (-65 to +150) (-65 to +150) 250 500 FR205 600 420 600 FR26 FR207 UNIT   Volts   Volts   Volts Amps Maximum Repetitive Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current, 0.375" (9.5mm) lead length at TA =75 Peak Forward Surge Current 8.3ms single half sine - wave superimposed on rated load (JEDEC method ) Maximum Instantaneous Forward Voltage at 2.0A Maximum DC Reverse Current at rated TA = 25 TA  DC blocking voltage Maximum Reverse Recovery Time (Note 3) Tj = 25 Typical Junction Capacitance (Note 1) Typical Thermal Resistance (Note2) Operating and Storage Temperature Range Storage Temperature Range NOTES: 1. Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts. IFSM VF IR trr CJ R
 TJ TSTG Amps Volts A nS pF /W   2. Thermal Resistance from Junction to Ambient at 0.375" (9.5mm) lead length, P.C. board mounted. 3. Reverse Recovery Test Condition: IF =0.5A, IR = 1.0A, IRR = 0.25A Web Site: WWW.PS-PFS.COM RATINGS AND CHARACTERISTIC CURVES FR201 THRU FR207 FIG.1-TYPICAL FORWARD CURRENT FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 70 60 PEAK FORWARD SURGE 50 CURRENT, (A) 8.3ms Single Half Sine-Wave (JEDEC Method) =T T j j max 40 30 20 0.375"(9.5mm) 10 0 1 1 Cycle 2 4 6 8 10 20 40 60 80 100 NUMBER OF CYCLES AT 60 Hz FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 20 FIG.4-TYPICAL REVERSE CHARACTERISTICS 10 INSTANTANEOUS FORWARD CURRENT, 10 INSTANTANEOUS REVERSE CURRENT, T =100 ° C j (A) 1.0 1.0 T =25 ° C Pulse Width=300uS 1% Duty Cycle j (uA) 0.1 0.1 T =25 ° C j 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0.01 0 20 40 60 80 100 120 140 INSTANTANEOUS FORWARD VOLT AGE,(V) PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) FIG.5-TYPICAL JUNCTION CAPACITANCE 100 FIG.6-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC Trr JUNCTION CAPACITANCE,(pF) 50 NONINDUCTIVE 10 NONINDUCTIVE (-) +0.5A 10 (+) 25 Vdc (approx.) (-) D.U.T. PULSE GENERATIOR (NOTE 2) (+) OSCILLOSCOPE (NOTE 1) 0 -0.25A 1 NON INDUCTIVE Tj =25 ° C f=1MHz V sig =50mV p-p NOTES: 1.Rise Time =7ns max. Input Impedance= 1 megohm. 22pF 2.Rise time=10ns max. Source Impedance= -1.0A 1cm SET TIME BASE FOR 50/100ns/cm 1 0.1 1.0 10 100 50 ohms REVRESE VOLTAGE,(V) Web Site: WWW.PS-PFS.COM