MUR160

MUR105 THRU MUR1100 Features • • • • High Surge Capability Low Forward Voltage Drop High Current Capability Super Fast Switching Speed For High Efficiency Maximum Ratings • • 1 Amp Super Fast Recovery Rectifier 50 to 1000 Volts Maximum DC Blocking Voltage 50V 100V 150V 200V 400V 600V 800V 1000V Operating Temperature: -50°C to +150 °C Storage Temperature: -50°C to +150 °C Maximum Recurrent Peak Reverse Voltage 50V 100V 150V 200V 400V 600V 800V 1000V DO-41 Part Number MUR105 MUR110 MUR115 MUR120 MUR140 MUR160 MUR180 MUR1100 Maximum RMS Voltage 35V 70V 105V 140V 280V 420V 560V 700V D Electrical Characteristics @ 25° C Unless Otherwise Specified Average Forward IF(AV) 1A TA = 55°C Current Peak Forward Surge IFSM 35A 8.3ms, half sine Current Maximum Instantaneous Forward Voltage IFM = 1.0A; VF .975V MUR105-115 1.35V MUR120-160 TA = 25°C 1.75V MUR180-1100 Maximum DC IR Reverse Current At 5µA TA = 25°C Rated DC Blocking 50µA TA = 150°C Voltage Maximum Reverse Recovery Time 45ns IF=0.5A, IR=1.0A, MUR105-120 Trr 60ns Irr=0.25A MUR140-160 MUR180-1100 75ns Typical Junction Measured at 20pF CJ Capacitance 1.0MHz, VR=4.0V *Pulse Test: Pulse Width 300µsec, Duty Cycle 1% A Cathode Mark B D C DIMENSIONS INCHES MIN .166 .080 .028 1.000 MM MIN 4.10 2.00 .70 25.40 DIM A B C D MAX .205 .107 .034 --- MAX 5.20 2.70 .90 --- NOTE Web Site: WWW.PS-PFS.COM MUR105 thru MUR1100 Figure 1 Typical Forward Characteristics 20 10 6 4 1.25 2 25°C Amps 1 .6 .4 .2 MUR120-160 .1 .06 .04 .02 .01 .5 .7 .9 1.1 1.3 1.5 0 .25 Single Phase, Half Wave 60Hz Resistive or Inductive Load 50 75 100 °C Average Forward Rectified Current - Amperes versus Ambient Temperature - °C 125 150 175 MUR180-1100 MUR105-115 .5 Amps 1.0 1.5 Figure 2 Forward Derating Curve .75 25 Volts Instantaneous Forward Current - Amperes versus Instantaneous Forward Voltage - Volts Figure 3 Junction Capacitance 100 60 40 20 pF 10 6 4 2 1 .1 .2 .4 1 Volts 2 4 10 20 40 100 200 400 1000 TJ=25°C Junction Capacitance - pF versus Reverse Voltage - Volts Web Site: WWW.PS-PFS.COM MUR105 thru MUR110 Figure 4 Typical Reverse Characteristics 100 60 40 20 10 6 4 2 TA=100 °C µAmps 1 .6 .4 .2 .1 TA =25°C .06 .04 .02 .01 20 40 60 80 Volts Instantaneous Reverse Leakage Current - MicroAmperes versus Percent Of Rated Peak Reverse Voltage - Volts Figure 6 Reverse Recovery Time Characteristic And Test Circuit Diagram 50Ω 10Ω trr +0.5A 0 25Vdc Pulse Generator Note 2 1Ω Notes: 1. Rise Time = 7ns max. Input impedance = 1 megohm, 22pF 2. Rise Time = 10ns max. Source impedance = 50 ohms 3. Resistors are non-inductive Oscilloscope Note 1 - 0.25 100 120 140 Amps TA =150 °C 60 50 40 30 20 10 0 1 2 4 6 8 10 20 Cycles Peak Forward Surge Current - Amperes versus Number Of Cycles At 60Hz - Cycles 40 60 80 100 Figure 5 Peak Forward Surge Current - 1.0 1 cm Set Time Base for 20/100ns/cm Web Site: WWW.PS-PFS.COM