SF63

SUPER FAST RECOVERY RECTIFIER SF61 THRU SF65 FEATURES • • • • • VOLTAGE RANGE CURRENT 50 to 400 Volts 6.0Ampere R-6 .052(1.3) .048(1.2) 1.0(25.4) MIN. DIA. Low coat construction Fast switching for high efficency. Low reverse leakage High forward surge current capability High temperature soldering guaranteed: 260℃/10 secods/.375”(9.5mm)lead length at 5 lbs(2.3kg) tension .360(9.1) .340(8.6) .360(9.1) .340(8.6) DIA. MECHANICAL DATA • • • • • • Case: Transfer molded plastic Epoxy: UL94V-O rate flame retardant Polarity: Color band denotes cathode end Lead: Plated axial lead, solderable per MIL-STD-202E method 208C Mounting position: Any Weight: 0.042ounce, 1.19grams 1.0(25.4) MIN. Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25OC ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% SYMBOLS Maximum Repetitive Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current 0.375”(9.5mm) lead length at T A= 55℃ Peak Forward Surge Current 8.3mS single half sine wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage @ 6.0A Maximum DC Reverse Current at Rated DC Blocking Voltage T A = 25℃ TA = 125℃ VRRM VRMS VDC I(AV) IFSM VF IR trr CJ RθJA TJ TSTG SF 61 50 35 50 SF 62 100 70 100 SF 63 150 105 150 6.0 150 SF 64 200 140 200 SF 65 300 210 300 UNITS Volts Volts Volts Amp Amps 0.95 5.0 50 35 60 30 (-55 to +150) (-55 to +150) 40 1.25 Volts µA ns PF ℃/W ℃ ℃ Maximum Reverse Recovery Time Test conditions IF=0.5A,IR=1.0A,IRR=0.25A Typical Thermal Capavitance (Measured at 1.0MHz and applied rever voltage of 4.0V) Typical Thermal Resistance(NOTE 1) Operating Junction Temperature Range Storage Temperature Range Notes: 1. Thermal resistance from junction to ambient with .375”(9.5mm)lead length, PCB. mounted. . Web Site: WWW.PS-PFS.COM SUPER FAST RECOVERY RECTIFIER SF61 THRU SF65 VOLTAGE RANGE CURRENT 50 to 400 Volts 6.0Ampere RATING AND CHRACTERISTIC CURVES SF61 THRU SF65 FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT FIG.1-TYPICAL FORWARD CURRENT DERATING CURVE 6.0 AVERAGE FORWARD CURRENT, 250 PEAK FORWARD SURGE 5.0 8.3ms Single Half Sine-Wave (JEDEC Method) Tj=Tjmax 4.0 (A) 3.0 2.0 1.0 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375"(9.5mm)Lead Length CURRENT, (A) 150 50 1 Cycle 0 1 2 0 0 25 50 55 75 100 125 150 175 4 6 8 10 20 40 60 100 AMBIENT TEMPERATURE, (° C) NUMBER OF CYCLES AT 60 Hz FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 100 FIG.4-TYPICAL REVERSE CHARACTERISTICS 10 INSTANTANEOUS FORWARD CURRENT, 10 INSTANTANEOUS REVERSE CURRENT, SF 61 -63 SF 64 -6 5 1.0 Tj =125 ° C (A) 1.0 (UA) 0.1 0.1 Tj =25° C Tj =25° C Pulse Width=300us 1% Duty Cycle 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) INSTANTANEOUS FORWARD VOLTAGE,(V) FIG.5-TYPICAL JUNCTION CAPACITANCE 100 JUNCTION CAPACITANCE,(pF) FIG.6-TEST CIRCUIT DIAGRAM AND REVERSE REXOVERY TIME CHARACTERISTIC Trr +0.5A 50Ω NONINDUCTIVE 10Ω N ONINDUCTIVE (-) 0 0.25A 10 (+) 25 Vdc （approx） (-) D.U.T PULSE GENERATIOR (NOTE 2) 1Ω NON INDUCTIVE OSCILLOSCOPE (NOTE 1) -1.0A 1cm TJ=25° C F=1MHz Vsig=50mVp-p SF61-SF63 SF64-SF65 1.0 0.1 1.0 10 100 NOTE: 1.Rise Time =7ns max.Input Impedance=1megohm.22pF 2.Rise time=10ns max.Source Impedance=50 ohms SET TIME BASE FOR 50 /100NS /cm REVERSE VOLTAGE,(V) Web Site: WWW.PS-PFS.COM