74AUP1G17GW

74AUP1G17 Low-power Schmitt-trigger buffer Rev. 01 — 26 July 2005 Product data sheet 1. General description The 74AUP1G17 is a high-performance, low-power, low-voltage, Si-gate CMOS device, superior to most advanced CMOS compatible TTL families. Schmitt-trigger action at all inputs makes the circuit tolerant to slower input rise and fall times across the entire VCC range from 0.8 V to 3.6 V. This device ensures a very low static and dynamic power consumption across the entire VCC range from 0.8 V to 3.6 V. This device is fully specified for partial Power-down applications using IOFF. The IOFF circuitry disables the output, preventing the damaging backflow current through the device when it is powered down. The 74AUP1G17 provides the single Schmitt-trigger buffer. It is capable of transforming slowly changing input signals into sharply defined, jitter-free output signals. 2. Features s Wide supply voltage range from 0.8 V to 3.6 V s High noise immunity s Complies with JEDEC standards: x JESD8-12 (0.8 V to 1.3 V) x JESD8-11 (0.9 V to 1.65 V) x JESD8-7 (1.2 V to 1.95 V) x JESD8-5 (1.8 V to 2.7 V) x JESD8-B (2.7 V to 3.6 V) s ESD protection: x HBM JESD22-A114-C exceeds 2000 V x MM JESD22-A115-A exceeds 200 V x CDM JESD22-C101-C exceeds 1000 V s Low static power consumption; ICC = 0.9 µA (maximum) s Latch-up performance exceeds 100 mA per JESD 78 Class II s Inputs accept voltages up to 3.6 V s Low noise overshoot and undershoot < 10 % of VCC s IOFF circuitry provides partial Power-down mode operation s Multiple package options s Specified from −40 °C to +85 °C and −40 °C to +125 °C Philips Semiconductors 74AUP1G17 Low-power Schmitt-trigger buffer 3. Quick reference data Table 1: Quick reference data GND = 0 V; Tamb = 25 °C; tr = tf ≤ 3 ns. Symbol Parameter Conditions CL = 5 pF; RL = 1 MΩ; VCC = 0.8 V CL = 5 pF; RL = 1 MΩ; VCC = 1.1 V to 1.3 V CL = 5 pF; RL = 1 MΩ; VCC = 1.4 V to 1.6 V CL = 5 pF; RL = 1 MΩ; VCC = 1.65 V to 1.95 V CL = 5 pF; RL = 1 MΩ; VCC = 2.3 V to 2.7 V CL = 5 pF; RL = 1 MΩ; VCC = 3.0 V to 3.6 V Ci CPD input capacitance power dissipation capacitance VCC = 1.8 V; f = 10 MHz VCC = 3.3 V; f = 10 MHz [1] [2] [1] [2] Min 2.9 2.5 2.2 2.0 1.9 - Typ 19.0 5.7 4.2 3.6 3.0 2.8 0.8 4.5 6.0 Max 11.7 7.2 5.9 4.8 4.3 - Unit ns ns ns ns ns ns pF pF pF tPHL, tPLH propagation delay A to Y [1] CPD is used to determine the dynamic power dissipation (PD in µW). PD = CPD × VCC2 × fi × N + Σ(CL × VCC2 × fo) where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; VCC = supply voltage in V; N = number of inputs switching; Σ(CL × VCC2 × fo) = sum of the outputs. The condition is VI = GND to VCC. [2] 4. Ordering information Table 2: Ordering information Package Temperature range Name 74AUP1G17GW 74AUP1G17GM −40 °C to +125 °C −40 °C to +125 °C TSSOP5 XSON6 Description plastic thin shrink small outline package; 5 leads; body width 1.25 mm Version SOT353-1 Type number plastic extremely thin small outline package; no leads; SOT886 6 terminals; body 1 × 1.45 × 0.5 mm 5. Marking Table 3: Marking Marking code pJ pJ Type number 74AUP1G17GW 74AUP1G17GM 9397 750 14677 © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Product data sheet Rev. 01 — 26 July 2005 2 of 20 Philips Semiconductors 74AUP1G17 Low-power Schmitt-trigger buffer 6. Functional diagram 2 A Y 4 2 4 mnb151 mnb150 Fig 1. Logic symbol Fig 2. IEC logic symbol A Y mnb152 Fig 3. Logic diagram 7. Pinning information 7.1 Pinning 17 n.c. n.c. A 1 2 5 VCC 1 6 VCC A 2 5 n.c. 17 GND 3 4 Y 4 001aab808 GND 3 Y 001aab809 Transparent top view Fig 4. Pin configuration SOT353-1 (TSSOP5) Fig 5. Pin configuration SOT886 (XSON6) 7.2 Pin description Table 4: Symbol n.c. A GND Y n.c. VCC Pin description Pin TSSOP5 1 2 3 4 5 XSON6 1 2 3 4 5 6 not connected data input A ground (0 V) data output Y not connected supply voltage Description 9397 750 14677 © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Product data sheet Rev. 01 — 26 July 2005 3 of 20 Philips Semiconductors 74AUP1G17 Low-power Schmitt-trigger buffer 8. Functional description 8.1 Function table Table 5: Input A L H [1] H = HIGH voltage level; L = LOW voltage level. Function table [1] Output Y L H 9. Limiting values Table 6: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Symbol Parameter VCC IIK VI IOK VO IO ICC IGND Tstg Ptot [1] [2] Conditions VI < 0 V [1] Min −0.5 −0.5 [1] [1] Max +4.6 −50 +4.6 ±50 +4.6 ±20 +50 −50 +150 250 Unit V mA V mA V mA mA mA °C mW supply voltage input clamping current input voltage output clamping current VO > VCC or VO < 0 V output voltage output current quiescent supply current ground current storage temperature total power dissipation Tamb = −40 °C to +125 °C [2] active mode Power-down mode VO = 0 V to VCC −0.5 −0.5 −65 - VCC + 0.5 V The input and output voltage ratings may be exceeded if the input and output current ratings are observed. For TSSOP5 packages: above 87.5 °C the value of Ptot derates linearly with 4.0 mW/K. For XSON6 packages: above 45 °C the value of Ptot derates linearly with 2.4 mW/K. 10. Recommended operating conditions Table 7: Symbol VCC VI VO Tamb Recommended operating conditions Parameter supply voltage input voltage output voltage ambient temperature active mode Power-down mode; VCC = 0 V Conditions Min 0.8 0 0 0 −40 Max 3.6 3.6 VCC 3.6 +125 Unit V V V V °C 9397 750 14677 © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Product data sheet Rev. 01 — 26 July 2005 4 of 20 Philips Semiconductors 74AUP1G17 Low-power Schmitt-trigger buffer 11. Static characteristics Table 8: Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Tamb = 25 °C VOH HIGH-state output voltage VI = VIH or VIL IO = −20 µA; VCC = 0.8 V to 3.6 V IO = −1.1 mA; VCC = 1.1 V IO = −1.7 mA; VCC = 1.4 V IO = −1.9 mA; VCC = 1.65 V IO = −2.3 mA; VCC = 2.3 V IO = −3.1 mA; VCC = 2.3 V IO = −2.7 mA; VCC = 3.0 V IO = −4.0 mA; VCC = 3.0 V VOL LOW-state output voltage VI = VIH or VIL IO = 20 µA; VCC = 0.8 V to 3.6 V IO = 1.1 mA; VCC = 1.1 V IO = 1.7 mA; VCC = 1.4 V IO = 1.9 mA; VCC = 1.65 V IO = 2.3 mA; VCC = 2.3 V IO = 3.1 mA; VCC = 2.3 V IO = 2.7 mA; VCC = 3.0 V IO = 4.0 mA; VCC = 3.0 V ILI IOFF ∆IOFF ICC ∆ICC Ci Co input leakage current power-off leakage current VI = GND to 3.6 V; VCC = 0 V to 3.6 V VI or VO = 0 V to 3.6 V; VCC = 0 V 0.8 1.7 0.1 0.3 × VCC 0.31 0.31 0.31 0.44 0.31 0.44 ±0.1 ±0.2 ±0.2 0.5 40 V V V V V V V V µA µA µA µA µA pF pF VCC − 0.1 1.11 1.32 2.05 1.9 2.72 2.6 V V V V V V V V 0.75 × VCC Conditions Min Typ Max Unit additional power-off leakage VI or VO = 0 V to 3.6 V; current VCC = 0 V to 0.2 V quiescent supply current additional quiescent supply current input capacitance output capacitance VI = GND or VCC; IO = 0 A; VCC = 0.8 V to 3.6 V VI = VCC − 0.6 V; IO = 0 A; VCC = 3.3 V VI = GND or VCC; VCC = 0 V to 3.6 V VO = GND; VCC = 0 V 9397 750 14677 © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Product data sheet Rev. 01 — 26 July 2005 5 of 20 Philips Semiconductors 74AUP1G17 Low-power Schmitt-trigger buffer Table 8: Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Tamb = −40 °C to +85 °C VOH HIGH-state output voltage VI = VIH or VIL IO = −20 µA; VCC = 0.8 V to 3.6 V IO = −1.1 mA; VCC = 1.1 V IO = −1.7 mA; VCC = 1.4 V IO = −1.9 mA; VCC = 1.65 V IO = −2.3 mA; VCC = 2.3 V IO = −3.1 mA; VCC = 2.3 V IO = −2.7 mA; VCC = 3.0 V IO = −4.0 mA; VCC = 3.0 V VOL LOW-state output voltage VI = VIH or VIL IO = 20 µA; VCC = 0.8 V to 3.6 V IO = 1.1 mA; VCC = 1.1 V IO = 1.7 mA; VCC = 1.4 V IO = 1.9 mA; VCC = 1.65 V IO = 2.3 mA; VCC = 2.3 V IO = 3.1 mA; VCC = 2.3 V IO = 2.7 mA; VCC = 3.0 V IO = 4.0 mA; VCC = 3.0 V ILI IOFF ∆IOFF ICC ∆ICC input leakage current power-off leakage current VI = GND to 3.6 V; VCC = 0 V to 3.6 V VI or VO = 0 V to 3.6 V; VCC = 0 V 0.1 0.3 × VCC 0.37 0.35 0.33 0.45 0.33 0.45 ±0.5 ±0.5 ±0.6 0.9 50 V V V V V V V V µA µA µA µA µA VCC − 0.1 0.7 × VCC 1.03 1.30 1.97 1.85 2.67 2.55 V V V V V V V V Conditions Min Typ Max Unit additional power-off leakage VI or VO = 0 V to 3.6 V; current VCC = 0 V to 0.2 V quiescent supply current additional quiescent supply current VI = GND or VCC; IO = 0 A; VCC = 0.8 V to 3.6 V VI = VCC − 0.6 V; IO = 0 A; VCC = 3.3 V 9397 750 14677 © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Product data sheet Rev. 01 — 26 July 2005 6 of 20 Philips Semiconductors 74AUP1G17 Low-power Schmitt-trigger buffer Table 8: Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Tamb = −40 °C to +125 °C VOH HIGH-state output voltage VI = VIH or VIL IO = −20 µA; VCC = 0.8 V to 3.6 V IO = −1.1 mA; VCC = 1.1 V IO = −1.7 mA; VCC = 1.4 V IO = −1.9 mA; VCC = 1.65 V IO = −2.3 mA; VCC = 2.3 V IO = −3.1 mA; VCC = 2.3 V IO = −2.7 mA; VCC = 3.0 V IO = −4.0 mA; VCC = 3.0 V VOL LOW-state output voltage VI = VIH or VIL IO = 20 µA; VCC = 0.8 V to 3.6 V IO = 1.1 mA; VCC = 1.1 V IO = 1.7 mA; VCC = 1.4 V IO = 1.9 mA; VCC = 1.65 V IO = 2.3 mA; VCC = 2.3 V IO = 3.1 mA; VCC = 2.3 V IO = 2.7 mA; VCC = 3.0 V IO = 4.0 mA; VCC = 3.0 V ILI IOFF ∆IOFF ICC ∆ICC input leakage current power-off leakage current VI = GND to 3.6 V; VCC = 0 V to 3.6 V VI or VO = 0 V to 3.6 V; VCC = 0 V 0.11 0.41 0.39 0.36 0.50 0.36 0.50 ±0.75 ±0.75 ±0.75 1.4 75 V V V V V V V µA µA µA µA µA 0.33 × VCC V VCC − 0.11 0.6 × VCC 0.93 1.17 1.77 1.67 2.40 2.30 V V V V V V V V Conditions Min Typ Max Unit additional power-off leakage VI or VO = 0 V to 3.6 V; current VCC = 0 V to 0.2 V quiescent supply current additional quiescent supply current VI = GND or VCC; IO = 0 A; VCC = 0.8 V to 3.6 V VI = VCC − 0.6 V; IO = 0 A; VCC = 3.3 V 9397 750 14677 © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Product data sheet Rev. 01 — 26 July 2005 7 of 20 Philips Semiconductors 74AUP1G17 Low-power Schmitt-trigger buffer 12. Dynamic characteristics Table 9: Dynamic characteristics Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 7 Symbol tPHL, tPLH Parameter propagation delay A to Y Conditions see Figure 6 VCC = 0.8 V VCC = 1.1 V to 1.3 V VCC = 1.4 V to 1.6 V VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 3.0 V to 3.6 V Tamb = 25 °C; CL = 10 pF tPHL, tPLH propagation delay A to Y see Figure 6 VCC = 0.8 V VCC = 1.1 V to 1.3 V VCC = 1.4 V to 1.6 V VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 3.0 V to 3.6 V Tamb = 25 °C; CL = 15 pF tPHL, tPLH propagation delay A to Y see Figure 6 VCC = 0.8 V VCC = 1.1 V to 1.3 V VCC = 1.4 V to 1.6 V VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 3.0 V to 3.6 V Tamb = 25 °C; CL = 30 pF tPHL, tPLH propagation delay A to Y see Figure 6 VCC = 0.8 V VCC = 1.1 V to 1.3 V VCC = 1.4 V to 1.6 V VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 3.0 V to 3.6 V 5.0 4.2 3.9 3.6 3.5 36.7 9.6 7.0 6.0 5.1 4.8 18.1 12.2 9.7 7.8 6.7 ns ns ns ns ns ns 3.8 3.3 3.0 2.8 2.7 26.4 7.4 5.4 4.7 4.0 3.8 14.8 9.3 7.5 6.1 5.4 ns ns ns ns ns ns 3.4 2.9 2.6 2.4 2.3 22.9 6.6 4.9 4.2 3.6 3.3 13.5 8.3 6.7 5.5 4.9 ns ns ns ns ns ns 2.9 2.5 2.2 2.0 1.9 19.0 5.7 4.2 3.6 3.0 2.8 11.7 7.2 5.9 4.8 4.3 ns ns ns ns ns ns Min Typ [1] Max Unit Tamb = 25 °C; CL = 5 pF 9397 750 14677 © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Product data sheet Rev. 01 — 26 July 2005 8 of 20 Philips Semiconductors 74AUP1G17 Low-power Schmitt-trigger buffer Table 9: Dynamic characteristics …continued Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 7 Symbol CPD Parameter Conditions [2] [3] Min Typ [1] Max Unit Tamb = 25 °C power dissipation capacitance f = 10 MHz VCC = 0.8 V VCC = 1.1 V to 1.3 V VCC = 1.4 V to 1.6 V VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 3.0 V to 3.6 V [1] [2] All typical values are measured at nominal VCC. CPD is used to determine the dynamic power dissipation (PD in µW). PD = CPD × VCC2 × fi × N + Σ(CL × VCC2 × fo) where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; VCC = supply voltage in V; N = number of inputs switching; Σ(CL × VCC2 × fo) = sum of the outputs. The condition is VI = GND to VCC. - 3.4 3.9 4.2 4.5 5.4 6.0 - pF pF pF pF pF pF [3] Table 10: Dynamic characteristics Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 7 Symbol CL = 5 pF tPHL, tPLH propagation delay A to Y see Figure 6 VCC = 1.1 V to 1.3 V VCC = 1.4 V to 1.6 V VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 3.0 V to 3.6 V CL = 10 pF tPHL, tPLH propagation delay A to Y see Figure 6 VCC = 1.1 V to 1.3 V VCC = 1.4 V to 1.6 V VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 3.0 V to 3.6 V 3.1 2.6 2.4 2.2 2.2 14.9 9.6 7.9 6.4 5.7 3.1 2.6 2.4 2.2 2.2 16.4 10.6 8.7 7.1 6.3 ns ns ns ns ns 2.7 2.3 2.0 1.8 1.7 13.0 8.4 7.0 5.6 5.0 2.7 2.3 2.0 1.8 1.7 14.3 9.3 7.7 6.2 5.5 ns ns ns ns ns Parameter Conditions −40 °C to +85 °C Min Max −40 °C to +125 °C Min Max Unit 9397 750 14677 © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Product data sheet Rev. 01 — 26 July 2005 9 of 20 Philips Semiconductors 74AUP1G17 Low-power Schmitt-trigger buffer Table 10: Dynamic characteristics …continued Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 7 Symbol CL = 15 pF tPHL, tPLH propagation delay A to Y see Figure 6 VCC = 1.1 V to 1.3 V VCC = 1.4 V to 1.6 V VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 3.0 V to 3.6 V CL = 30 pF tPHL, tPLH propagation delay A to Y see Figure 6 VCC = 1.1 V to 1.3 V VCC = 1.4 V to 1.6 V VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 3.0 V to 3.6 V 4.5 3.8 3.5 3.3 3.3 19.8 14.4 11.6 9.3 7.7 4.5 3.8 3.5 3.3 3.3 21.8 15.9 12.8 10.3 8.5 ns ns ns ns ns 3.5 2.9 2.7 2.5 2.5 16.7 10.9 8.8 7.2 6.2 3.5 2.9 2.7 2.5 2.5 18.4 12.0 9.7 8.0 6.9 ns ns ns ns ns Parameter Conditions −40 °C to +85 °C Min Max −40 °C to +125 °C Min Max Unit 13. Waveforms VI A input GND t PHL VOH Y output VOL VM mnb153 VM t PLH Measurement points are given in Table 11. Logic levels: VOL and VOH are typical output voltage drop that occur with the output load. Fig 6. The data input (A) to output (Y) propagation delays Table 11: VCC 0.8 V to 3.6 V Measurement points Output VM 0.5 × VCC Input VM 0.5 × VCC VI VCC tr = tf ≤ 3.0 ns Supply voltage 9397 750 14677 © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Product data sheet Rev. 01 — 26 July 2005 10 of 20 Philips Semiconductors 74AUP1G17 Low-power Schmitt-trigger buffer VCC VEXT 5 kΩ PULSE GENERATOR VI VO DUT RT CL RL 001aac521 Test data is given in Table 12. Definitions for test circuit: RL = Load resistor CL = Load capacitance including jig and probe capacitance RT = Termination resistance should be equal to the output impedance Zo of the pulse generator Fig 7. Load circuitry for switching times Table 12: VCC 0.8 V to 3.6 V [1] Test data Load CL RL [1] Supply voltage VEXT tPLH, tPHL tPZH, tPHZ GND tPZL, tPLZ 2 × VCC 5 pF, 10 pF, 5 kΩ or 1 MΩ open 15 pF and 30 pF For measuring enable and disable times RL = 5 kΩ, for measuring propagation delays, setup and hold times and pulse width RL = 1 MΩ. 14. Transfer characteristics Table 13: Transfer characteristics Voltages are referenced to GND (ground = 0 V). Symbol V(th)LH Parameter Conditions Min Typ Max Unit Tamb = 25 °C positive-going see Figure 8 and Figure 9 threshold voltage VCC = 0.8 V VCC = 1.1 V VCC = 1.4 V VCC = 1.65 V VCC = 2.3 V VCC = 3.0 V V(th)HL negative-going see Figure 8 and Figure 9 threshold voltage VCC = 0.8 V VCC = 1.1 V VCC = 1.4 V VCC = 1.65 V VCC = 2.3 V VCC = 3.0 V 0.30 0.53 0.74 0.91 1.37 1.88 0.10 0.26 0.39 0.47 0.69 0.88 0.60 0.90 1.11 1.29 1.77 2.29 0.60 0.65 0.75 0.84 1.04 1.24 V V V V V V V V V V V V 9397 750 14677 © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Product data sheet Rev. 01 — 26 July 2005 11 of 20 Philips Semiconductors 74AUP1G17 Low-power Schmitt-trigger buffer Table 13: Transfer characteristics …continued Voltages are referenced to GND (ground = 0 V). Symbol Vhys Parameter hysteresis voltage (V(th)LH − V(th)HL) Conditions see Figure 8, Figure 9, Figure 10 and Figure 11 VCC = 0.8 V VCC = 1.1 V VCC = 1.4 V VCC = 1.65 V VCC = 2.3 V VCC = 3.0 V Tamb = −40 °C to +85 °C V(th)LH positive-going see Figure 8 and Figure 9 threshold voltage VCC = 0.8 V VCC = 1.1 V VCC = 1.4 V VCC = 1.65 V VCC = 2.3 V VCC = 3.0 V V(th)HL negative-going see Figure 8 and Figure 9 threshold voltage VCC = 0.8 V VCC = 1.1 V VCC = 1.4 V VCC = 1.65 V VCC = 2.3 V VCC = 3.0 V Vhys hysteresis voltage (V(th)LH − V(th)HL) see Figure 8, Figure 9, Figure 10 and Figure 11 VCC = 0.8 V VCC = 1.1 V VCC = 1.4 V VCC = 1.65 V VCC = 2.3 V VCC = 3.0 V Tamb = −40 °C to +125 °C V(th)LH positive-going see Figure 8 and Figure 9 threshold voltage VCC = 0.8 V VCC = 1.1 V VCC = 1.4 V VCC = 1.65 V VCC = 2.3 V VCC = 3.0 V 0.30 0.53 0.74 0.91 1.37 1.88 0.62 0.92 1.13 1.31 1.80 2.32 V V V V V V 0.07 0.08 0.18 0.27 0.53 0.79 0.50 0.46 0.56 0.66 0.92 1.31 V V V V V V 0.30 0.53 0.74 0.91 1.37 1.88 0.10 0.26 0.39 0.47 0.69 0.88 0.60 0.90 1.11 1.29 1.77 2.29 0.60 0.65 0.75 0.84 1.04 1.24 V V V V V V V V V V V V 0.07 0.08 0.18 0.27 0.53 0.79 0.50 0.46 0.56 0.66 0.92 1.31 V V V V V V Min Typ Max Unit 9397 750 14677 © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Product data sheet Rev. 01 — 26 July 2005 12 of 20 Philips Semiconductors 74AUP1G17 Low-power Schmitt-trigger buffer Table 13: Transfer characteristics …continued Voltages are referenced to GND (ground = 0 V). Symbol V(th)HL Parameter Conditions Min 0.10 0.26 0.39 0.47 0.69 0.88 Typ Max 0.60 0.65 0.75 0.84 1.04 1.24 Unit V V V V V V negative-going see Figure 8 and Figure 9 threshold voltage VCC = 0.8 V VCC = 1.1 V VCC = 1.4 V VCC = 1.65 V VCC = 2.3 V VCC = 3.0 V Vhys hysteresis voltage (V(th)LH − V(th)HL) see Figure 8, Figure 9, Figure 10 and Figure 11 VCC = 0.8 V VCC = 1.1 V VCC = 1.4 V VCC = 1.65 V VCC = 2.3 V VCC = 3.0 V 0.07 0.08 0.18 0.27 0.53 0.79 0.50 0.46 0.56 0.66 0.92 1.31 V V V V V V 15. Waveforms transfer characteristics VO VI V(th)LH Vhys V(th)HL VO Vhys V(th)HL V(th)LH VI mnb154 mnb155 V(th)LH and V(th)HL limits at 70 % and 20 %. Fig 8. Transfer characteristic Fig 9. Definition of V(th)LH, V(th)HL and Vhys 9397 750 14677 © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Product data sheet Rev. 01 — 26 July 2005 13 of 20 Philips Semiconductors 74AUP1G17 Low-power Schmitt-trigger buffer 1.2 ICC (mA) 0.8 001aad025 0.4 0 0 0.4 0.8 1.2 1.6 VI (V) 2.0 Fig 10. Typical transfer characteristics; VCC = 1.8 V 4 ICC (mA) 3 001aad026 2 1 0 0 1 2 VI (V) 3 Fig 11. Typical transfer characteristics; VCC = 3.0 V 9397 750 14677 © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Product data sheet Rev. 01 — 26 July 2005 14 of 20 Philips Semiconductors 74AUP1G17 Low-power Schmitt-trigger buffer 16. Application information The slow input rise and fall times cause additional power dissipation, this can be calculated using the following formula: Pad = fi × (tr × ICC(AV) + tf × ICC(AV)) × VCC where: Pad = additional power dissipation (µW); fi = input frequency (MHz); tr = input rise time (ns); 10 % to 90 %; tf = input fall time (ns); 90 % to 10 %; ICC(AV) = average additional supply current (µA). Average ICC differs with positive or negative input transitions, as shown in Figure 12. 001aad027 1.2 ICC (mA) 0.8 (1) 0.4 (2) 0 0.8 1.8 2.8 VCC (V) 3.8 (1) Positive-going edge. (2) Negative-going edge. Fig 12. Average ICC as a function of VCC 9397 750 14677 © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Product data sheet Rev. 01 — 26 July 2005 15 of 20 Philips Semiconductors 74AUP1G17 Low-power Schmitt-trigger buffer 17. Package outline TSSOP5: plastic thin shrink small outline package; 5 leads; body width 1.25 mm SOT353-1 D E A X c y HE vMA Z 5 4 A2 A1 (A3) θ A 1 e e1 bp 3 wM detail X Lp L 0 1.5 scale 3 mm DIMENSIONS (mm are the original dimensions) UNIT mm A max. 1.1 A1 0.1 0 A2 1.0 0.8 A3 0.15 bp 0.30 0.15 c 0.25 0.08 D(1) 2.25 1.85 E(1) 1.35 1.15 e 0.65 e1 1.3 HE 2.25 2.0 L 0.425 Lp 0.46 0.21 v 0.3 w 0.1 y 0.1 Z(1) 0.60 0.15 θ 7° 0° Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. OUTLINE VERSION SOT353-1 REFERENCES IEC JEDEC MO-203 JEITA SC-88A EUROPEAN PROJECTION ISSUE DATE 00-09-01 03-02-19 Fig 13. Package outline SOT353-1 (TSSOP5) 9397 750 14677 © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Product data sheet Rev. 01 — 26 July 2005 16 of 20 Philips Semiconductors 74AUP1G17 Low-power Schmitt-trigger buffer XSON6: plastic extremely thin small outline package; no leads; 6 terminals; body 1 x 1.45 x 0.5 mm SOT886 b 1 2 3 4× L1 L (2) e 6 e1 5 e1 4 6× (2) A A1 D E terminal 1 index area 0 DIMENSIONS (mm are the original dimensions) UNIT mm A (1) max 0.5 A1 max 0.04 b 0.25 0.17 D 1.5 1.4 E 1.05 0.95 e 0.6 e1 0.5 L 0.35 0.27 L1 0.40 0.32 1 scale 2 mm Notes 1. Including plating thickness. 2. Can be visible in some manufacturing processes. OUTLINE VERSION SOT886 REFERENCES IEC JEDEC MO-252 JEITA EUROPEAN PROJECTION ISSUE DATE 04-07-15 04-07-22 Fig 14. Package outline SOT886 (XSON6) 9397 750 14677 © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Product data sheet Rev. 01 — 26 July 2005 17 of 20 Philips Semiconductors 74AUP1G17 Low-power Schmitt-trigger buffer 18. Abbreviations Table 14: Acronym CMOS TTL HBM ESD MM CDM Abbreviations Description Complementary Metal Oxide Semiconductor Transistor Transistor Logic Human Body Model ElectroStatic Discharge Machine Model Charged Device Model 19. Revision history Table 15: Revision history Release date 20050726 Data sheet status Product data sheet Change notice Doc. number 9397 750 14677 Supersedes Document ID 74AUP1G17_1 9397 750 14677 © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Product data sheet Rev. 01 — 26 July 2005 18 of 20 Philips Semiconductors 74AUP1G17 Low-power Schmitt-trigger buffer 20. Data sheet status Level I II Data sheet status [1] Objective data Preliminary data Product status [2] [3] Development Qualification Definition This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). III Product data Production [1] [2] [3] Please consult the most recently issued data sheet before initiating or completing a design. The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. 21. Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status ‘Production’), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. 23. Trademarks Notice — All referenced brands, product names, service names and trademarks are the property of their respective owners. 22. Disclaimers Life support — These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors 24. Contact information For additional information, please visit: http://www.semiconductors.philips.com For sales office addresses, send an email to: sales.addresses@www.semiconductors.philips.com 9397 750 14677 © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Product data sheet Rev. 01 — 26 July 2005 19 of 20 Philips Semiconductors 74AUP1G17 Low-power Schmitt-trigger buffer 25. Contents 1 2 3 4 5 6 7 7.1 7.2 8 8.1 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick reference data . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 4 Function table . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4 Recommended operating conditions. . . . . . . . 4 Static characteristics. . . . . . . . . . . . . . . . . . . . . 5 Dynamic characteristics . . . . . . . . . . . . . . . . . . 8 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Transfer characteristics. . . . . . . . . . . . . . . . . . 11 Waveforms transfer characteristics . . . . . . . . 13 Application information. . . . . . . . . . . . . . . . . . 15 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 16 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 18 Data sheet status . . . . . . . . . . . . . . . . . . . . . . . 19 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Contact information . . . . . . . . . . . . . . . . . . . . 19 © Koninklijke Philips Electronics N.V. 2005 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 26 July 2005 Document number: 9397 750 14677 Published in The Netherlands