74LVC125PWDH

INTEGRATED CIRCUITS 74LVC125 Quad buffer/line driver; 3-State Product specification Supersedes data of February 1996 IC24 Data Handbook 1997 Mar 18 Philips Semiconductors Philips Semiconductors Product specification Quad buffer/line driver; 3-State 74LVC125 FEATURES • Wide supply voltage range of 1.2 to 3.6 V • In accordance with JEDEC standard no. 8-1A • Inputs accept voltages up to 5.5 V • CMOS lower power consumption • Direct interface with TTL levels • Output drive capability 50 W transmission lines at 85°C QUICK REFERENCE DATA GND = 0 V; Tamb = 25°C; tr = tf ≤ 2.5 ns SYMBOL tPHL/tPLH CI CPD PARAMETER Propagation delay nA to nY Input capacitance Power dissipation capacitance per buffer DESCRIPTION The 74LVC125 is a high performance, low-power, low-voltage Si-gate CMOS device and superior to most advanced CMOS compatible TTL families. The 74LVC125 consists of four non-inverting buffers/line drivers with 3-State outputs. The 3-State outputs (nY) are controlled by the output enable input (nOE). A HIGH at nOE causes the outputs to assume a high impedance OFF-state. CONDITIONS CL = 15 pF; VCC = 3.3 V Notes 1 and 2 TYPICAL 3.5 5.0 22 UNIT ns pF pF NOTES: 1. CPD is used to determine the dynamic power dissipation (PD in µW) PD = CPD × VCC2 × fi +Σ (CL × VCC2 × fo) where: fi = input frequency in MHz; CL = output load capacity in pF; fo = output frequency in MHz; VCC = supply voltage in V; Σ (CL × VCC2 × fo) = sum of the outputs. 2. The condition is VI = GND to VCC ORDERING INFORMATION PACKAGES 14-Pin Plastic SO 14-Pin Plastic SSOP Type II 14-Pin Plastic TSSOP Type I TEMPERATURE RANGE –40°C to +85°C –40°C to +85°C –40°C to +85°C OUTSIDE NORTH AMERICA 74LVC125 D 74LVC125 DB 74LVC125 PW NORTH AMERICA 74LVC125 D 74LVC125 DB 74LVC125PW DH PKG. DWG. # SOT108-1 SOT337-1 SOT402-1 PIN CONFIGURATION 1OE 1A 1Y 2OE 2A 2Y GND 1 2 3 4 5 6 7 14 13 12 11 10 9 8 VCC 4OE 4A 4Y 3OE 3A 3Y LOGIC SYMBOL 2 1A 1Y 3 1 5 1OE 2A 2Y 6 4 9 2OE 3A 3Y 8 10 3OE 4A 4Y 11 SV00455 12 PIN DESCRIPTION PIN NUMBER 1, 4, 10, 13 2, 5, 9, 12 3, 6, 8, 11 7 14 SYMBOL 1OE – 4OE 1A – 4A 1Y – 4Y GND VCC NAME AND FUNCTION Data enable inputs (active LOW) Data inputs Data Outputs Ground (0 V) Positive supply voltage 13 4OE SV00456 1997 Mar 18 2 853–1951 17865 Philips Semiconductors Product specification Quad buffer/line driver; 3-State 74LVC125 FUNCTION TABLE INPUTS nOE L L H NOTES: H = HIGH voltage level L = LOW voltage level X = don’t care Z = high impedance OFF-state nA L H X OUTPUT nY L H Z LOGIC SYMBOL (IEEE/IEC) 2 1 3 1 EN1 5 6 4 9 8 10 12 11 13 SV00457 RECOMMENDED OPERATING CONDITIONS SYMBOL VCC VCC VI VI/O VO Tamb tr, tf PARAMETER DC supply voltage (for max. speed performance) DC supply voltage (for low-voltage applications) DC input voltage range DC input voltage range for I/Os DC output voltage range Operating free-air temperature range Input rise and fall times VCC = 1.2 to 2.7V VCC = 2.7 to 3.6V CONDITIONS LIMITS MIN 2.7 1.2 0 0 0 –40 0 0 MAX 3.6 3.6 5.5 VCC VCC +85 20 10 UNIT V V V V V °C ns/V ABSOLUTE MAXIMUM RATINGS1 In accordance with the Absolute Maximum Rating System (IEC 134). Voltages are referenced to GND (ground = 0 V). SYMBOL VCC IIK VI VI/O IOK VOUT IOUT IGND, ICC Tstg PTOT PARAMETER DC supply voltage DC input diode current DC input voltage DC input voltage range for I/Os DC output diode current DC output voltage DC output source or sink current DC VCC or GND current Storage temperature range Power dissipation per package – plastic mini-pack (SO) – plastic shrink mini-pack (SSOP and TSSOP) above +70°C derate linearly with 8 mW/K above +60°C derate linearly with 5.5 mW/K VO uVCC or VO t 0 Note 2 VO = 0 to VCC VI t 0 Note 2 CONDITIONS RATING –0.5 to +6.5 –50 –0.5 to +5.5 –0.5 to VCC +0.5 "50 –0.5 to VCC +0.5 "50 "100 –60 to +150 500 500 UNIT V mA V V mA V mA mA °C mW NOTES: 1. Stresses beyond those listed may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 1997 Mar 18 3 Philips Semiconductors Product specification Quad buffer/line driver; 3-State 74LVC125 DC ELECTRICAL CHARACTERISTICS Over recommended operating conditions. Voltages are referenced to GND (ground = 0 V). LIMITS SYMBOL PARAMETER TEST CONDITIONS Temp = -40°C to +85°C MIN VIH HIGH level Input voltage level Input voltage VCC = 1.2V VCC = 2.7 to 3.6V LOW level Input voltage level Input voltage VCC = 1.2V VCC = 2.7 to 3.6V VCC = 2.7V; VI = VIH or VIL; IO = –12mA VO OH HIGH level output voltage level output voltage VCC = 3.0V; VI = VIH or VIL; IO = –100µA VCC = 3.0V; VI = VIH or VIL; IO = –12mA VCC = 3.0V; VI = VIH or VIL; IO = –24mA VCC = 2.7V; VI = VIH or VIL; IO = 12mA VOL LOW level output voltage VCC = 3.0V; VI = VIH or VIL; IO = 100µA VCC = 3.0V; VI = VIH or VIL; IO = 24mA II IIHZ/IILZ IOZ ICC ∆ICC Input leakage current Input leakage current Input current for common I/O pins 3-State output OFF-state current Quiescent supply current Additional quiescent supply current per input pin VCC = 3.6V; VI = 5.5V or GND or GND VCC = 3.6V; VI = VCC or GND VCC = 3.6V; VI = VIH or VIL; VO = VCC or GND VCC = 3.6V; VI = VCC or GND; IO = 0 VCC = 2.7V to 3.6V; VI = VCC –0.6V; IO = 0 Not for I/O pins for I/O "0.1 "0.1 0.1 0.1 5 GND VCC*0.5 VCC*0.2 VCC*0.6 VCC*1.0 0.40 0.20 0.55 "5 "15 "10 20 500 µA µA µA µA µA V VCC V VCC 2.0 GND V 0.8 TYP1 MAX V UNIT VIL NOTE: 1. All typical values are at VCC = 3.3V and Tamb = 25°C. 1997 Mar 18 4 Philips Semiconductors Product specification Quad buffer/line driver; 3-State 74LVC125 AC CHARACTERISTICS GND = 0 V; tr = tf = 2.5 ns; CL = 50 pF; RL = 500W; Tamb = –40_C to +85_C. LIMITS SYMBOL PARAMETER WAVEFORM VCC = 3.3V ±0.3V MIN tPHL tPLH tPZH tPZL tPHZ tPLZ Propagation delay nA to nY 3-state output enable time nOE to nY 3-state output disable time nOE to nY Figure 1, 3 Figure 2, 3 Figure 2, 3 TYP1 3.5 3.8 3.3 MAX 6.5 7.0 5.5 MIN VCC = 2.7V TYP 3.9 4.4 4.0 MAX 7.0 8.0 6.5 VCC = 1.2V TYP ns ns ns UNIT NOTE: 1. These typical values are at VCC = 3.3V and Tamb = 25°C. AC WAVEFORMS VM = 1.5 V at VCC w 2.7 V VM = 0.5 × VCC at VCC < 2.7 V VOL and VOH are the typical output voltage drop that occur with the output load. VX = VOL + 0.3 V at VCC ≥ 2.7 V; VX = VOL + 0.1 × VCC at VCC < 2.7 V; VY = VOH – 0.3 V at VCC ≥ 2.7 V; VY = VOH – 0.1 × VCC at VCC < 2.7 V. Vl nA INPUT GND t PHL V OH nY OUTPUT V OL VM t PLH VM TEST CIRCUIT VCC S1 2 < VCC Open GND PULSE GENERATOR VI D.U.T. RT VO 500Ω CL 50pF 500Ω Test VCC t 2.7V 2.7V – 3.6V VI VCC 2.7V tPLH/tPHL tPLZ/tPZL tPHZ/tPZH S1 Open 2 < VCC GND SY00003 Figure 3. Load circuitry for switching times. SV00459 Figure 1. Input (nA) to output (nY) propagation delays. VI nOE Input GND tPLZ VCC OUTPUT LOW-to-OFF OFF-to-LOW VOL tPHZ VOH OUTPUT HIGH-to-OFF OFF-to-HIGH GND outputs enabled VY VM outputs disabled outputs enabled tPZL VM VX tPZH VM SV00458 Figure 2. 3-State enable and disable times. 1997 Mar 18 5 Philips Semiconductors Product specification Quad buffer/line driver; 3-State 74LVC125 SO14: plastic small outline package; 14 leads; body width 3.9 mm SOT108-1 1997 Mar 18 6 Philips Semiconductors Product specification Quad buffer/line driver; 3-State 74LVC125 SSOP14: plastic shrink small outline package; 14 leads; body width 5.3 mm SOT337-1 1997 Mar 18 7 Philips Semiconductors Product specification Quad buffer/line driver; 3-State 74LVC125 TSSOP14: plastic thin shrink small outline package; 14 leads; body width 4.4 mm SOT402-1 1997 Mar 18 8 Philips Semiconductors Product specification Quad buffer/line driver; 3-State 74LVC125 NOTES 1997 Mar 18 9 Philips Semiconductors Product specification Quad buffer/line driver; 3-State 74LVC125 DEFINITIONS Data Sheet Identification Objective Specification Product Status Formative or in Design Definition This data sheet contains the design target or goal specifications for product development. Specifications may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes at any time without notice, in order to improve design and supply the best possible product. Preliminary Specification Preproduction Product Product Specification Full Production Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. LIFE SUPPORT APPLICATIONS Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices, or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale. Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381 © Copyright Philips Electronics North America Corporation 1997 All rights reserved. Printed in U.S.A. Philips Semiconductors 1997 Mar 18 10