83C145

INTEGRATED CIRCUITS DATA SH EET 83C145; 83C845 83C055; 87C055 Microcontrollers for TV and video (MTV) Product specification File under Integrated Circuits, IC20 1996 Mar 22 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) CONTENTS 1 2 3 4 5 5.1 6 6.1 6.2 7 8 9 9.1 10 10.1 10.2 11 11.1 11.2 11.3 11.4 12 12.1 12.2 13 13.1 13.2 13.3 13.4 13.5 13.6 13.7 13.8 13.9 FEATURES DESCRIPTION APPLICATIONS ORDERING INFORMATION BLOCK DIAGRAM Part options PINNING INFORMATION Pinning Pin description DESCRIPTION OF STANDARD FUNCTIONS INPUT/OUTPUT (I/O) DESCRIPTION OF DERIVATIVE FUNCTIONS General description 6-BIT PWM DACS PWM DAC operation Special Function Register PWMn (n = 0 to 7) 14-BIT PWM DAC (TDAC) 14-bit counter 14-bit DAC operation Special Function Register TDACL Special Function Register TDACH SOFTWARE ANALOG-TO-DIGITAL FACILITY Special Function Register SAD Software ADC operation ON SCREEN DISPLAY (OSD) OSD features General description of the OSD module OSD logic Character Generator ROM Display RAM organization OSD Special Function Registers OSD Control Register OSCON OSD Control Register OSMOD OSD Control Register OSORG 14 14.1 14.2 14.3 14.4 14.5 15 15.1 15.2 15.3 16 17 18 19 20 21 22 22.1 22.2 22.3 23 24 83C145; 83C845 83C055; 87C055 PROGRAMMING CONSIDERATIONS EPROM Characteristics Programming operation Erasure Characteristics Reading Signature Bytes EPROM Programming and Verification PROGRAMMING THE OSD EPROM Overview Character description and programming OSD EPROM bit map REGISTER MAP LIMITING VALUES HANDLING DC CHARACTERISTICS AC CHARACTERISTICS PACKAGE OUTLINES SOLDERING Introduction Soldering by dip or wave Repairing soldered joints DEFINITIONS LIFE SUPPORT APPLICATIONS 1996 Mar 22 2 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 1 FEATURES 83C145; 83C845 83C055; 87C055 • One 14-bit PWM for high-precision voltage integration • Digital-to-analog converter and comparator with 3 inputs multiplexer • Nine dedicated I/Os plus 28 port bits (15 port bits with alternative uses) • 4 high current open-drain port outputs • 12 high voltage (+12 V) open-drain outputs • Programmable video input and output polarities • 80C51 instruction set • No external memory capability • Plastic shrink dual in-line package (0.07 inch centre pins) • High-speed CMOS technology • Power supply: 5 V ±10%. 2 DESCRIPTION • Masked ROM sizes: – 8 kbytes (83C845) – 12 kbytes (83C145) – 16 kbytes (83C055) – 16 kbytes OTP (87C055) • RAM: 256 bytes • On Screen Display (OSD) controller • Three digital video outputs • Multiplexer/mixer and background intensity controls • Flexible formatting with OSD New Line option • 128 × 10 bits display RAM • Designed for reduced Radio Frequency Interference (RFI) • Character generator ROM: – character format 18 lines × 14 dots – 60 visible characters – 4 special characters • Eight text shadowing modes • Text colour selectable per character • Background colour selectable per word • Background colour versus video selectable per character • Eight 6-bit Pulse Width Modulators (PWM) for analog voltage integration 4 ORDERING INFORMATION The 83C055, Microcontroller for Television and Video (MTV) applications, is a derivative of Philips’ industry standard 80C51 microcontroller. The 83C055 is intended for use as the central control mechanism in a television receiver or tuner. 3 APPLICATIONS Providing tuner functions and an OSD facility, it represents a next generation replacement for the currently available parts. PACKAGE TYPE NUMBER NAME P83C055BBP P87C055BBP P83C145BBP P83C845BBP SDIP42 plastic shrink dual in-line package; 42 leads (600 mil) SOT270-1 DESCRIPTION VERSION TEMP. RANGE (°C) FREQ. (MHz) 0 to +70 3.5 to 12 1996 Mar 22 3 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 5 BLOCK DIAGRAM 83C145; 83C845 83C055; 87C055 handbook, full pagewidth T0 INT1 INT0 BF VID1 VCTRL VCLK1 HSYNC VID2 VID0 VCLK2 VSYNC VDD XTAL1 (IN) OSD BLOCK 8-BIT TIMER / EVENT COUNTER CHARACTER GENERATOR ROM 60 × 18 × 14 CPU ROM (1) RAM 256 bytes XTAL2 (OUT) DISPLAY RAM 128 × 10 8-bit internal bus RST 80C51 core excluding ROM / RAM PARALLEL I/O PORTS 8 x 6-BIT PWM 14-BIT PWM SOFTWARE CONTROL ADC V SS 8 P3 P2 8 4 P1 8 P0 8 PWM0 to PWM7 TDAC 3 ADI2 to ADI0 MBE766 (1) ROM sizes: see Table 1. Fig.1 Block diagram. 5.1 Part options Differences between the types TYPES MEMORY 83C845 83C145 12 kbytes − 83C055 16 kbytes − 87C055 − 16 kbytes Table 1 ROM EPROM (OTP) 8 kbytes − 1996 Mar 22 4 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 6 6.1 PINNING INFORMATION Pinning 83C145; 83C845 83C055; 87C055 handbook, halfpage handbook, halfpage VPP/TDAC/P0.0 1 2 3 4 5 6 7 8 9 42 VDD 41 P3.7 40 P3.6 39 P3.5 38 P3.4 37 P3.3/INT0 36 P3.2/T0 35 P3.1/INT1 34 P3.0 PROG/PWM1/P0.1 ASEL/PWM2/P0.2 PWM3/P0.3 PWM4/P0.4 PWM5/P0.5 PWM6/P0.6 PWM7/P0.7 ADI0/P1.0 ADI1/P1.1 10 ADI2/P1.2 11 PWM0/P1.3 12 P2.7 13 P2.6 14 P2.5 15 P2.4 16 P2.3 17 P2.2 18 P2.1 19 P2.0 20 VSS 21 83C145 83C845 83C055 87C055 33 RST 32 XTAL2 31 XTAL1 30 BF 29 VCLK2 28 VCLK1 27 VSYNC 26 HSYNC 25 VCTRL 24 VID2 23 VID1 22 VID0 MBE765 Fig.2 Pin configuration (SOT270-1). 1996 Mar 22 5 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 6.2 Pin description Pin description SDIP42 (SOT270-1) PIN DESCRIPTION 83C145; 83C845 83C055; 87C055 Table 2 SYMBOL Port 0 (notes 1, 2 and 4) P0.0/TDAC/VPP 1 P0.0: open-drain bidirectional port line; TDAC: output for the 14-bit high-precision PWM; VPP: 12 V programming supply voltage during EPROM programming. P0.1: open-drain bidirectional port line; PWM1: output for the 6-bit lower-precision PWM; PROG: input for EPROM programming pulses. P0.2: open-drain bidirectional port line; PWM2: output for the 6-bit lower-precision PWM; ASEL: input indicating the EPROM address bits that are applied to Port 2. P0.3 to P0.7: 5 open-drain bidirectional port lines; PWM3 to PWM7: 5 outputs for the 6-bit lower-precision PWM. P0.1/PWM1/PROG 2 P0.2/PWM2/ASEL 3 P0.3/PWM3 to P0.7/PWM7 4 to 8 Port 1 (notes 1, 2 and 5) P1.0/ADI0 to P1.2/ADI2 P1.3/PWM0 Port 2 P2.7 to P2.0 13 to 20 Port 2: 8-bit open-drain bidirectional port; P2.3 to P2.0 have high current capability (10 mA at 0.5 V) for driving LEDs. Port 2 pins that have logic 1s written to them float, and in that state can be used as high-impedance inputs. Any of the Port 2 pins are driven LOW if the port register bit is written as a logic 0. The state of the pin can always be read from the port register by the program. 9 to 11 P1.0 to P1.2: 3 open-drain bidirectional port lines; ADI0 to ADI2: inputs for the software analog-to-digital facility. P1.3: open-drain bidirectional port line; PWM0: output for the 6-bit lower-precision PWM. PWM0 can be externally pulled up as high as +12 V ±5% 12 Port 3 (note 1 and 3) P3.0 P3.1/INT1 P3.2/T0 P3.3/INT0 P3.4 to P3.7 General VSS VID2 to VID0 21 Ground: 0 V reference. 22 to 24 Digital Video bus: Three totem-pole outputs comprising digital RGB (or other colour encoding) from the OSD facility. The polarity of these outputs is controlled by a programmable register bit (register OSCON; bit Po). 25 Video Control: A totem-pole output indicating whether the OSD facility is currently presenting active video on the VID2 to VID0 outputs. Signal is used to control an external multiplexer (mixer) between normal video and the video derived from VID2 to VID0. The polarity of this output is controlled by a programmable register bit (register OSCON; bit Pc). 34 35 36 37 P3.0: open-drain bidirectional port line. P3.1: open-drain bidirectional port line; INT1: External interrupt 1. P3.2: open-drain bidirectional port line; T0: Timer 0 external input. P3.3: open-drain bidirectional port line; INT0: External interrupt 0. 38 to 41 P3.4 to P3.7: 4 open-drain bidirectional port lines. VCTRL 1996 Mar 22 6 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 83C145; 83C845 83C055; 87C055 DESCRIPTION SYMBOL HSYNC PIN 26 Horizontal Sync: A dedicated input for a TTL-level version of the horizontal sync pulse. The polarity of this pulse is programmable; its trailing edge is used by the OSD facility as the reference for horizontal positioning. Vertical Sync: A dedicated input for a TTL-level version of the vertical sync pulse. The polarity of this pulse is programmable, and either edge can serve as the reference for vertical timing. VCLK1: Video Clock 1; input for the horizontal timing reference for the OSD facility. VCLK2: Video Clock 2; output from the on-chip video oscillator. VCLK1 and VCLK2 are intended to be used with an external LC circuit to provide an on-chip oscillator. The period of the video clock is determined such that the width of a pixel in the OSD is equal to the inter-line separation of the raster. Background/Foreground: A totem-pole output which, when VCTRL is active, indicates whether the current video data represents a Foreground (LOW) or Background (HIGH) dot in a character. This signal can be used to reduce the intensity of the background colour and thus emphasize the text. XTAL1: Input to the inverting (oscillator) amplifier and clock generator circuit that provides the timing reference for all 83C055 logic other than the OSD facility. XTAL2: Oscillator output terminal for system clock. XTAL1 and XTAL2 can be used with a quartz crystal or ceramic resonator to provide an on-chip oscillator. Alternatively, XTAL1 can be connected to an external clock, and XTAL2 left unconnected. Reset: If this pin is HIGH for two machine cycles (24 oscillator periods) while the oscillator is running, the MTV is reset. This pin is also used as a serial input to enter a test or EPROM programming mode, as on the 87C751. Power supply: for normal and Power-down operation. VSYNC 27 VCLK1 VCLK2 28 29 BF 30 XTAL1 XTAL2 31 32 RST 33 VDD Notes 42 1. Port 0, Port 1 , and Port 3 pins that have logic 1s written to them float, and in that state can be used as high-impedance inputs. 2. The state of the pin can always be read from the port register by the program. 3. P3.0, P3.4, and P3.7 can be externally pulled up as high as +12 V ±5%; while P3.5 and P3.6 have 10 mA drive capability. 4. For each PWM block, a register bit (register PWMn; bit PWnE; n = 0 to 7) controls whether the corresponding pin is controlled by the block or by Port 0; Port 0 controls the pin immediately after a reset. Regardless of how each pin is controlled, it can be externally pulled up as high as +12 V ±5%. 5. Any of the Port 1 pins are driven LOW if the corresponding port register bit is written as a logic 0, or for P1.3 only, if the TDAC module presents a logic 0. 1996 Mar 22 7 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 7 DESCRIPTION OF STANDARD FUNCTIONS 83C145; 83C845 83C055; 87C055 For a description of the standard functions please refer to the “Data Handbook IC20; Section 2: 80C51 Technical Description” . 8 INPUT/OUTPUT (I/O) • The IP register is not used, and the IE register (address A8H) is similar to that on the 80C51;see Table 36. • The VSYNC input used by the OSD facility can generate an interrupt. The active polarity of the pulse is programmable (see Section 13.7); interrupt occurs at the leading edge of the pulse. • Since there is no serial port, there are no interrupts nor control bits relating to this interrupt. The interrupts and their vector addresses are shown in Table 3. • External Interrupt 1 is modified so that an interrupt is generated when the input switches are in either direction (on the 80C51, there is a programmable choice between interrupt on a negative edge or a LOW level on INT1). This facility allows for software pulse-width measurement handling of a remote control. Table 3 Program Memory address PROGRAM MEMORY ADDRESS 000H 003H 00BH 013H 01BH 023H The I/O structure of the 83C055 is similar to the standard I/O structure in the 80C51, except for the points described in Table 5. 9 9.1 DESCRIPTION OF DERIVATIVE FUNCTIONS General description Although the 83C055 is specifically referred to throughout this data sheet, the information applies to all the devices. The differences to 80C51 features and the derivative functions are described in the following Sections and Chapters. Figure 1 shows the block diagram of the 83C055. 9.1.1 NOT IMPLEMENTED FUNCTIONS EVENT Reset External INT0 Timer 0 External INT1 Timer 1 VSync Start 9.1.3 Standard functions to the 80C51 that are not implemented in the 83C055: • As Data and Program Memory are not externally expandable on the 83C055, the ALE, EA, and PSEN signals are not implemented. • Idle mode. • Power-down mode. 9.1.2 INTERRUPT FACILITIES DIFFERENCES PCON REGISTER DIFFERENCE The PCON register format is shown in Table 4. Bits GF1 and GF0 are general purpose flag bits. Table 4 7 − PCON Register format (address 87H) 6 − 5 − 4 − 3 GF1 2 GF0 1 − 0 − The interrupt facilities of the 83C055 differ from those of the 80C51 as follows: 9.1.4 Table 5 I/O Port 0 Port 1 Port 2 Port 3 I/O PORTS DIFFERENCES I/O ports differences STANDARD 80C51 external memory expansion 8-bit general purpose quasi-bidirectional quasi-bidirectional and can be used for external memory expansion 83C055 8-bit open-drain bidirectional port; and includes: alternative use for PWM outputs 4-bit open-drain port, and includes alternative uses for analog inputs and a PWM output open-drain and general purpose quasi-bidirectional; all eight bits have alternate uses 3 port bits have some of the same alternative uses as on the 80C51 but not necessarily on the same pins; 5 pins are open-drain and general purpose 1996 Mar 22 8 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 10 6-BIT PWM DACS Figure 3 shows the 6-bit PWM DAC logic circuit, consisting of 8 PWMn modules. The basic MCU clock is divided by 4 to get a waveform that clocks a 14-bit counter which is common to all the PWMs (including the 14-bit PWM). This divided clock is hereafter called the PWM clock. As illustrated in Fig.3, the lower-precision (6-bit) PWMs use the least significant part of the 14-bit counter. Figure 4 shows the circuit diagram of a 6-bit PWM module. Each PWM module has a Special Function Register PWMn; n = 0 to 7. The register format is shown in Table 6. 10.1 PWM DAC operation 83C145; 83C845 83C055; 87C055 When the value matches, the output flip-flop is cleared, so that the output pin is driven LOW. When the value rolls over to zero, the output flip-flop is set, so that the output pin is released. Thus the output waveform has a fixed period of 64 PWM clock cycles; its duty cycle is determined by contents of PWMn.5 to PWMn.0 (PVn5 to PVn0). Three of the nine total PWM modules (8 PWMn and the 14-bit PWM DAC) operate as previously described; for three others, both the rising and falling edges of the output are delayed by one PWM clock; for the remaining three, both edges are delayed by two PWM clocks. This feature reduces the radio-frequency emission that would otherwise occur when the counter rolled over to zero and all nine open-drain outputs were released. Value field PVn5 to PVn0 of each PWMn register (n = 0 to 7) is compared to the 6 LSBs of the common counter (14-bit counter). 10.2 Special Function Register PWMn (n = 0 to 7) Special Function Register PWMn (n = 0 to 7; addresses D4H to DFH) 6 − 5 PVn5 4 PVn4 3 PVn3 2 PVn2 1 PVn1 0 PVn0 Table 6 7 PWnE Table 7 BIT 7 Description of PWMn bits SYMBOL PWnE DESCRIPTION PWM module enable bit. If for a particular PWM block (n) the bit: PWnE = 1, then the block is active and controls its assigned port pin. PWnE = 0, the corresponding port pin is controlled by the port. 6 5 to 0 − Reserved. PVn5 to PVn0 Value field for PWMn register. 1996 Mar 22 9 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 83C145; 83C845 83C055; 87C055 handbook, full pagewidth ZERO P1.3 6 1st PWM MODULE (n = 0) 8 PWM0/P1.3 8 6 2nd PWM MODULE (n = 1) 8 P0.1 PWM1/P0.1 6 3rd to 7th PWM MODULE (n = 2 to 6) 8 P0.2 to P0.6 PWM2/P0.2 to PWM6/P0.6 6 8th PWM MODULE (n = 7) 8 6 LS 6-bits 14-BIT COUNTER PWM clock 4 fxtal 14-BIT PWM DAC BLOCK MBE771 - 1 P0.7 PWM7/P0.7 internal bus Fig.3 6-bit PWM DAC logic circuit. handbook, full pagewidth I/O port PWM module (n) ZERO LS 6-bits 6-bit COMPARATOR 6-bits (PVn0 to PVn5) 8 PVn0 PVn1 PVn2 PVn3 PVn4 PVn5 PWnE (1) (2) PWMn I/O pin internal bus PWM clock MBE770 (1) This flip-flop occurs in 5 of the 8 PWMn modules. (2) This flip-flop occurs in 3 of the 8 PWMn modules. Fig.4 A 6-bit PWM module. 1996 Mar 22 10 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 11 14-BIT PWM DAC (TDAC) 11.1 14-bit counter 11.2.2 83C145; 83C845 83C055; 87C055 HIGH PRECISION OPERATION The 14-bit counter was already mentioned in Section 10. The nature of the counter is such that it can achieve a stable output value through its MSB, and the value can propagate through logic like that shown in Fig.5. The logic output can be stable within: • one period of the PWM clock (e.g. 250 ns) if edge-triggered logic is used to capture the logic output, or • one phase of the PWM clock (e.g. 125 ns) if a phase of the PWM clock is used to capture the logic output. The 14-bit (TDAC) counter is a ripple counter (cost and die-size reasons). The 14-bit PWM DAC is controlled by two special function registers TDACL and TDACH. 11.2 14-bit DAC operation For the higher-precision aspect of this feature, the 7 MSBs of the counter are used in a logic block with the 7 LSBs of the programmed value. The 7th LSB (binary value 64) of the programmed value is ANDed with the 7th MSB (128) of the counter, the 6th LSB of the value is ANDed with the counter’s 6th and 7th MSBs being 10, and so on through the LSB of the programmed value being ANDed with the counter’s 7 MSBs being 100000. Then these 7 ANDed terms are ORed. If the result is true (logic 1) at the time the 7 LSBs of the counter match the MSBs of the programmed value, the output is forced high for 1 (additional) PWM clock cycle. The result is that, if the value-64 bit of the 14-bit value is programmed to a logic 1, every other cycle of 128 PWM counter clocks has its duty cycle stretched by one counter clock; if the value-32 bit is programmed to logic 1, every 4th cycle is stretched, and so on through, if the value-1 bit is programmed to logic 1, one cycle out of each 128 is stretched. 11.2.3 14-BIT DAC OUTPUT When software wishes to change the 14-bit value (TD0 to TD13), it should first write to TDACL and then write to TDACH. Alternatively, if the required precision of the duty cycle is satisfied by 6 bits or less, software can simply write to TDACH (TD8 to TD13). 11.2.1 LOW PRECISION OPERATION Assuming the external integrator can handle all this, the net effect is a PWM DAC that has the period of a 7-bit design (which makes the integrator easier and more feasible to design) with the accuracy of a 14-bit one. An obvious prerequisite for such precision is that the load on the voltage must be very light, like a single op-amp or comparator. Figure 5 shows that this block includes an ‘extra’ 14-bit latch between TDACL - TDACH and the comparator and other logic. The programmed value is clocked into the operative latch when the 7 low-order bits of the counter roll over to zero, provided that the software is not in the midst of loading a new 14-bit value, i.e. it is not between writing TDACL and writing TDACH. In a similar fashion to the lower-precision PWMs, this facility has an output flip-flop that is set when the lower 7 bits of the counter overflow/wrap. The more significant 7 bits of the operative latch’s programmed value are compared for equality against the less significant 7 bits of the counter, and the output FF is cleared when they match. Thus this output has a fixed period of 128 PWM clock cycles, and the duty cycle is determined by the programmed value. 11.2.3.1 Note The TDAC feature differs from the corresponding features of predecessor parts in several ways: 1. The 14-bit value is functionally composed of major and minor portions of 7 bits each. 2. The 14-bit value is programmed as a contiguous multi-register value that can be manipulated straight-forwardly via arithmetic instructions. 3. As discussed for the 6-bit DACs, both of the preceding parts had a feature whereby the PWM output could be inverted, redundantly with complementing the 14-bit value. This feature has been eliminated. 1996 Mar 22 11 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 11.3 Special Function Register TDACL Special Function Register TDACL format (address D2H) 6 TD0 5 TD1 4 TD2 3 TD3 2 TD4 83C145; 83C845 83C055; 87C055 Table 8 7 TD7 Table 9 BIT 1 TD5 0 TD6 Description of TDACL bits SYMBOL TD7, TD0 to TD6 8 LSBs of the 14-bit value. DESCRIPTION 7 to 0 11.4 Special Function Register TDACH Table 10 Special Function Register TDACH format (address D3H) 7 TDE 6 − 5 TD13 4 TD12 3 TD11 2 TD10 1 TD9 0 TD8 Table 11 Description of TDACH bits BIT 7 6 5 to 0 SYMBOL TDE − Enable bit. Reserved. DESCRIPTION TD13 to TD8 6 MSBs of the 14-bit value. 1996 Mar 22 12 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 83C145; 83C845 83C055; 87C055 handbook, full pagewidth 7 7 INTERNAL BUS TDACH TDACL 8 8 14-BIT LATCH 7 MSB 7 8 8 7 LSB 7 7-BIT COMPARATOR 7 TDACH.7 TDAC/ P0.0 P0.0 7 7 7 LSB 7 MSB PWM clock 14-BIT COUNTER 4 fxtal MBE774 Fig.5 14-bit PWM logic circuit. 1996 Mar 22 13 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 12 SOFTWARE ANALOG-TO-DIGITAL FACILITY 83C145; 83C845 83C055; 87C055 Figure 6 shows the software analog-to-digital facility block diagram. The block includes Special Function Register SAD. 12.1 Special Function Register SAD Table 12 Special Function Register SAD format (address D8H) 7 VHi 6 CH1 5 CH0 4 St 3 SAD3 2 SAD2 1 SAD1 0 SAD0 Table 13 Description of SAD bits BIT 7 6 5 4 3 to 0 12.2 SYMBOL VHi CH1 CH0 St The St bit should be written as a logic 1 in order to initiate a voltage comparison. SAD3 to SAD0 4 LSBs of the SAD register. Table 14 Pin selection: P1.n/ADIn CH1 0 0 1 1 Note 1. Port 1 has open-drain drivers which will not materially affect an analog voltage as long as any and all pins used for software analog-to-digital measurement have corresponding logic 1s in the port register; n = 0, 1, 2. CH0 0 1 0 1 P1.n/ADIn(1) none P1.0/ADI0 P1.1/ADI1 P1.2/ADI2 DESCRIPTION The comparator output bit; bit addressable. The channel field controls which pin, if any, is connected to this facility; see Table 14. Software ADC operation Port pins P1.0/ADI0 to P1.2/ADI2 can be alternately selected as inputs of a linear voltage comparator. The other input of the comparator is connected to a 4-bit DAC. This DAC is controlled by bits SAD3 to SAD0 and produces a reference voltage: nominally 0.15625 to 4.84375 V in increments of 0.3125 V. The output of the comparator (HIGH or LOW) can be read by the program as the MSB of the SAD register i.e. bit VHi. After writing St = 1, the program should include intervening instructions totalling at least 6 machine cycles (72 clock periods or 6 µs at 12 MHz), before the instruction that accesses and tests VHi. 1996 Mar 22 14 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 83C145; 83C845 83C055; 87C055 handbook, full pagewidth I/O PORT P1.0/ADI0 VOLTAGE COMPARATOR I/O PORT P1.1/ADI1 ANALOG MUX I/O PORT P1.2/ADI2 4-BIT DAC SAD.6:5 SAD.3:0 internal bus MBE772 Fig.6 Software analog-to-digital facility. 1996 Mar 22 15 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 13 ON SCREEN DISPLAY (OSD) Figure 7 shows the OSD block diagram. It shows the CPU writing into the 128 × 10 display RAM, which is dual-ported to allow the CPU to write into it at any time, including when it is being read out by the OSD logic. The 10-bit wide data coming out of the display RAM is used to access the appropriate character in the Character Generator memory (6-bits) and to specify character and display control functions (4-bits). Timing for the OSD is controlled by the HSYNC, VSYNC, and dot clock input VCLK1. 13.1 OSD features 13.1.3 83C145; 83C845 83C055; 87C055 DUAL-PORTED DISPLAY RAM The OSD has a true display RAM instead of a character line buffer. This display RAM is dual-ported to allow updating the display RAM at any time instead of having to wait for a vertical retrace. Vertical Sync (VSYNC) interrupts are supported if flicker-free updates are required. 13.1.4 PROGRAMMABLE CHARACTER SIZE • Normal characters are displayed as 18 × 14 bit maps. • In an interlaced display: – 2 fields are displayed so that one actually sees a 36 × 14 pixel size character. – The part has a double height and width mode which displays 36 × 28 pixel size bit maps per field. • For use in non-interlaced systems, the part has a double height mode so that the displayed characters have the same pixel size (36 × 14) as on an interlaced display. 13.1.5 CHARACTER SHADOWING The 83C055 features an advanced OSD function with some unique features as described in Sections 13.1.1 to 13.1.10. 13.1.1 USER-DEFINABLE DISPLAY FORMAT The OSD does not restrict the user to a fixed number of lines with a fixed number of characters per line: • Using a fixed number of lines restricts the generation of displays that can be differentiated from others that use the same chip and places limits on screen content. • Using a fixed number of characters per line wastes display RAM if a line has less than the full number of displayable characters (it has to be padded with non-visible characters). The OSD on the 83C055 defines a control character: • New Line, that has the same function as a Carriage Return and Line Feed. When the OSD circuitry fetches this character from display RAM it stops displaying further characters, waits for the next horizontal scan line, and starts displaying the next character in display RAM after the New Line character was received. The number of lines is thus up to the user, within the limits of the display and memory, as are the number of characters per line. This allows far better control of the appearance of the OSD. 13.1.2 COLOURS SELECTABLE BY CHARACTER When characters are displayed overlaid on a background of base video, a black border around the characters makes them highly legible. This feature is called shadowing. The 83C055 has 8 shadowing modes to allow the user to select various partial shadow modes as well as full surround shadow; see Fig.8 and Table 28. 13.1.6 PROGRAMMABLE POLARITIES Inputs to and outputs from the OSD can be programmed to be recognized as active LOW or HIGH. In conjunction with the 12 V outputs, this allows direct interfacing to most video signal processing circuits. 13.1.7 CHARACTER GENERATOR MEMORY IN EPROM On the 87C055, the Character Generator memory is in EPROM. This feature allows quick and inexpensive font development and refinement against the alternative of creating a masked ROM version to see how the final fonts will appear. 13.1.8 HSYNC LOCKED DOT CLOCK OSCILLATOR Characters can be displayed on a background of the base video or a programmable background colour. The background colour is selectable by word and the choice of background (base video/user programmed colour) by character. The 83C055 is designed to use an LC oscillator circuit that is started at the trailing edge of HSYNC and stopped at its leading edge. In practice, this gives a highly consistent delay from HSYNC to oscillator start and is stable from scan line to scan line so that no left margin effects are seen. 1996 Mar 22 16 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 13.1.9 SHORT ROWS 83C145; 83C845 83C055; 87C055 Figure 7 shows the 3 major elements of the OSD facility: • OSD logic • Display RAM • Character Generator ROM. 13.3 OSD logic This mode only displays 4 horizontal lines and is used for generating underlines. 13.1.10 PROGRAMMABLE HORIZONTAL AND VERTICAL POSITIONS Bit pairs HS4 to HS0 and VS2 to VS0 in register OSORG (Table 30) define the starting point of the display. 13.2 General description of the OSD module For a standard NTSC TV signal with an HSYNC frequency of 15.750 kHz and a VSYNC frequency of nominally 60 Hz, there are roughly 50 µs of active horizontal scan line available. A typical pixel clock frequency is 8 MHz, and therefore roughly 400 pixels of resolution can be obtained. At 14 dots per character, this means 28 character per horizontal scan line. If the 12 dot per character display mode is used, that means 33 character per horizontal scan line. Allowing for edge effects, 26 characters (14 across) or 31 characters (12 across) can be displayed. Note that VGA rates and higher can be used. The minimum character dot size will be a function of the VGA frequency used. For a 640 × 480 display, running at 33 kHz, the equivalent 83C055 pixel resolution is about 160 across (because of the 8 MHz clock and allowing for overscan). This means that status and diagnostic information can be displayed on video monitors. 13.3.1 ON-CHIP VIDEO OSCILLATOR This block is the largest of the additions that are specific to this product. Its basic function is to superimpose text on the television video image, to indicate various parameters and settings of the receiver or tuner. External circuitry handles the mixing (multiplexing) of the text and the TV video. The OSD block has 4 input pins: • Two for a video clock: VCLK1 and VCLK2 • Horizontal sync signal: HSYNC • Vertical sync signal: VSYNC. The block has 4 outputs: • 3 colour video signals • a control signal. Since this block is the major feature of the part, its main inputs and outputs are dedicated pins, without alternate port bits. The OSD of the 83C055 differs from that in preceding devices in one major way: • It does not fix the number and size of displayed rows of text. Several predecessor parts allowed two displayed rows of 16 characters each. The 83C055 simply has 128 locations of Display RAM, each of which can contain: • a displayed character, or • a New Line character that indicates the end of a row. A variant of the New Line character is used to indicate the end of displayed data. A number of changes in the OSD architecture have reduced the number of other Special Function Registers involved in the feature, below the number needed with predecessor devices: 1. The elimination of certain options such as 4, 6, or 8 × character sizes and alternate use of two of the video outputs. 2. The moving of certain other options from central registers to Display RAM, such as foreground colour codes (Fcolor) and background (B) selection. The video clock pins (VCLK1 and VCLK2) are used to connect a LC circuit to an on-chip video oscillator that is independent of the normal MCU clock. The L and C values are chosen so that a video pulse, of a duration equal to the VCLK period, will produce a more-or-less square dot on the screen, that is, a dot having a width approximately equal to the vertical distance between consecutive scan lines. The video oscillator is stopped (with VCLK2 = LOW) while: • HSYNC (Horizontal Sync) is maintained, and • is released to operate at the trailing edge of HSYNC. This technique helps provide uniform horizontal positioning of characters/dots from one scan line to the next. 1996 Mar 22 17 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 13.4 Character Generator ROM 13.5 83C145; 83C845 83C055; 87C055 Display RAM organization Character Generator ROM. Containing 60 displayable bit maps, i.e. 64 minus 4, comprising: • One for each of new line: New Line, and • Three space characters: – Space – BSpace – SplitBSpace. Each bit map includes 18 scan lines by 14 dots. The Character Generator ROM is maskable or programmable along with the Program ROM to allow for various character sets and languages. Each Display RAM location includes: • 6 data bits, and • 4 attribute bits. The 6 data bits from Display RAM, along with a line-within-row count, act as addresses into the Character Generator ROM. Except in special test modes that are beyond the scope of this data sheet, Display RAM cannot be read by the MCU program. dbook, full pagewidth HSYNC OSD LOGIC VSYNC 7 VCLK2 VCLK1 internal bus 7 OSD RAM 128 × 10 4 ATTRIBUTE CONTROL VCTRL VID2 6 RGB DIGITAL VIDEO OUT VID1 CHARACTER GENERATOR ADDRESS LOGIC 6 CHARACTER GENERATOR 60 × 18 × 14 VID0 MBG323 Fig.7 OSD block diagram. 1996 Mar 22 18 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 13.6 OSD Special Function Registers 83C145; 83C845 83C055; 87C055 The programming interface to Display RAM is provided by three Special Function Registers as shown in Tables 15, 17 and 20. Writing OSAT simply latches the attribute bits into a register, while writing OSDT causes the data bus information, plus the contents of the OSAT register, to be written into display RAM. Thus, for a given Display RAM location, OSAT should be written before OSDT. If successive characters are to be written into Display RAM with the same attributes, OSAT 13.6.1 SPECIAL FUNCTION REGISTER OSAD need not be rewritten for each character, only prior to writing OSDT for the first character with those particular attributes. The OSAT attribute bits associated with the BSpace, SplitBSpace and New Line characters (see Table 19) are interpreted differently from those that accompany other data characters. With BSpace and SplitBSpace, B is interpreted as described above, but the 3 colour bits specify the background colour (Bcolor) for subsequent characters. For BSpace, a change in B and Bcolor becomes effective at the left edge of the character’s bit map. Table 15 Special Function Register OSAD (On Screen ADdress; address 9AH) 7 − 6 OSAD6 5 OSAD5 4 OSAD4 3 OSAD3 2 OSAD2 1 OSAD1 0 OSAD0 Table 16 Description of OSAD bits BIT 7 6 to 0 SYMBOL − OSAD6 to OSAD0 Reserved. These 7-bits hold the Display RAM address into which data will be loaded. OSAD is automatically incremented by one each time OSDT and Display RAM are written to. DESCRIPTION 13.6.2 SPECIAL FUNCTION REGISTER OSDT Writing OSDT causes the data bus information, plus the contents of the OSAT register, to be written into display RAM. Table 17 Special Function Register OSDT (On Screen DaTa; address 99H) 7 − 6 − 5 OSDT5 4 OSDT4 3 OSDT3 2 OSDT2 1 OSDT1 0 OSDT0 Table 18 Description of OSDT bits BIT 7 to 6 5 to 0 SYMBOL − OSDT5 to OSDT0 Reserved. Character data; see Table 19. In reality, there is a potential conflict between the timing of a write to OSDT and an access to display RAM by the OSD logic for data display. This is resolved by the use of a true dual-ported RAM for display memory. DESCRIPTION 1996 Mar 22 19 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) Table 19 Special characters related to OSDT register SPECIAL CHARACTER New Line Space (normal) BSpace SplitBspace 13.6.3 OSDT5 1 1 1 1 OSDT4 1 1 1 1 OSDT3 1 1 1 1 OSDT2 1 1 1 1 83C145; 83C845 83C055; 87C055 OSDT1 0 0 1 1 OSDT0 1 0 0 1 SPECIAL FUNCTION REGISTER OSAT Table 20 Special Function Register OSAT ( On Screen ATtributes; address 98H) WITH OSDT = New Line BSpace SplitBSpace Any other character 7 − − − − 6 − − − − 5 − − − − 4 E B B B 3 − − − − 2 SR BC2 BC2 FC2 1 D BC1 BC1 FC1 0 Sh BC0 BC0 FC0 Table 21 Description of OSAT bits BIT 7 to 5, 3 SYMBOL − Reserved. DESCRIPTION With OSDT = New Line; note 1 4 2 1 0 E SR D Sh End; If the E bit is 1, no further rows are displayed on the screen. Short row; If E = 0 and SR = 1, the next row is a ‘short row’, i.e. it is only 4 or 8 scan lines high rather than 18 or 36. Short rows can be used for underlined text. Double height; If E = 0 and D = 1, all of the characters in the following row are displayed with ‘double height and width’. Shadowing; If E = 0 and Sh = 1, all of the characters in the following row are displayed with ‘shadowing’; see Section 13.8. With OSDT = BSpace or SplitBspace; note 2 4 2 to 0 B Background; B indicates whether ‘background pixels’ should show the current background colour (B = 1), or television video (B = 0). BC2 to BC0 Bcolor: Background colour (notes 3 and 4; see Table 22). With OSDT = Any other character 4 2 to 0 B Background; B indicates whether ‘background pixels’ should show the current background colour (B = 1), or television video (B = 0). FC2 to FC0 Fcolor: Foreground colour. Fcolor indicates the colour of ‘foreground pixels’ in the ROM bit map for this character (see Table 22). 1996 Mar 22 20 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) Notes to the description of OSAT bits 83C145; 83C845 83C055; 87C055 1. The latches in which the E,SR, D, and Sh bits are captured are cleared to zero at the start of each vertical scan. This means that if the first text line on the screen is a short row, or if it contains either double size or shadowing, the text must be preceded by a New Line character. Like all such characters, this initial New Line advances the vertical screen position; the VStart value (see register OSORG; Section 13.9) should take this fact into account. 2. For SplitBSpace, a change in B and Bcolor occurs halfway through the character horizontally. 3. The normal Space character has no effect on the Bcolor value. 4. The Bcolor value is not cleared between vertical scans, so that if a single background colour is all that is needed in an application, it can be set via a single BSpace character during program initialization, and never changed thereafter. In order for such a BSpace to actually affect the 83C055 internal Bcolor register the Mode field of the OSMOD register must be set to ‘01B’ (or higher) so that the OSD hardware is operating (see register OSMOD; Section 13.8). Table 22 OSD outputs related to character bit map value, Fcolor, Bcolor and B bits OSD OUTPUTS (notes 1 and 2) CHARACTER BIT MAP VALUE VID2 logic 1 logic 0 Notes 1. Bcolor (BC2,BC1,BC0) values ‘000’ and ‘111’ minimize the occurrence of transient states among the VID2 to VID0 outputs. 2. The background colour defined by the most recently encountered BSpace or SplitBSpace character is maintained on the VID2 to VID0 pins except at the following times: a) During the active time of HSYNC. b) During the active time of VSYNC. c) During those pixels of an active character that correspond to a logic 1 in the character’s bit map. d) During a ‘shadow’ bit. FC2 BC2 VID1 FC1 BC1 VID0 FC0 BC0 VCTRL driven active B 1996 Mar 22 21 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 13.7 OSD Control Register OSCON 83C145; 83C845 83C055; 87C055 Table 23 OSD Control Register OSCON (address C0H) 7 IV 6 Pv 5 Lv 4 Ph 3 Pc 2 Po 1 DH 0 BFe Table 24 Description of OSCON bits (see note 1) BIT 7 SYMBOL IV DESCRIPTION Interrupt flag for the OSD feature. Bit IV is set by the leading edge of the VSYNC pulse, and is cleared by the hardware when the VSYNC interrupt routine is vectored to. It can also be set or cleared by software writing a logic 1 or logic 0 to this bit. Pv defines the active VSYNC input polarity. If Pv = 0, then VSYNC input is active HIGH; if Pv = 1, then VSYNC input is active LOW. One effect of bit Pv is that the VID2 to VID0 and VCTRL outputs are blocked (held at black/inactive) during the active time of VSYNC. The IV bit is set on the leading edge of the VSYNC pulse; thus Pv controls whether the OSD interrupt occurs in response to a HIGH-to-LOW or LOW-to-HIGH transition on VSYNC. Lv defines the active edge of VSYNC. The active edge (leading or trailing) of VSYNC (as defined by Pv), clears the state counter which determines the vertical start of on screen data. Time reference for the video field is the leading edge of VSYNC, if Lv = 0, or the trailing edge of VSYNC, if Lv = 1. Ph defines the active HSYNC input polarity. If Ph = 0, then HSYNC input is active HIGH; if Ph = 1, then HSYNC input is active LOW. Pc defines the active VCTRL output polarity; VCTRL output active means: show the colour on VID2 to VID0. If Pc = 0, then VCTRL output is active HIGH; If Pc = 1, then VCTRL output is active LOW. Po defines the VID2 to VID0 outputs polarity; bit is needed only because the Shadowing feature needs to generate black pixels without reference to a register value. Internally, the 3-bit code ‘000B’ always designates black. If Po = 0, a logic 0 internal to the 83C055 corresponds to a LOW on one of the VID2 to VID0 pins. If Po = 1, a logic 1 internal to the 83C055 corresponds to a LOW on one of the VID2 to VID0 pins. 1 DH If DH = 1, character sizes are doubled vertically but not horizontally. This feature allows the 83C055 to be used in ‘improved definition’ systems that are not interlaced. The vertical doubling imposed by DH does not affect the VStart logic as described in Table 30; it operates in HSync units regardless of DH or D. Background/Foreground enable; output BF. If BFe = 1, then the BF output tracks whether each bit in displayed characters is a Foreground bit (LOW), or a Background bit (HIGH). If BFe = 0, then the BF pin remains HIGH. 6 Pv 5 Lv 4 3 Ph Pc 2 Po 0 BFe Note 1. It is theoretically possible that a VSYNC interrupt could be missed, or an extra one generated, if OSCON is read, then modified internally (e.g. in ACC), and the result written back to OSCON. However, none of the other bits in OSCON are reasonable candidates for dynamic change. Special provisions are included in the 83C055 logic so that IV will not be changed by a single ‘read-modify-write’ instruction such as SETB or CLR, unless the instruction specifically changes IV. 1996 Mar 22 22 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 13.8 OSD Control Register OSMOD 83C145; 83C845 83C055; 87C055 Under some conditions writing to OSMOD while the display is active can cause a temporary flicker during that display field. This can be avoided by only writing to OSMOD during the vertical sync interval. Table 25 OSD Control Register OSMOD (address C1H) 7 Wc 6 − 5 Mode1 4 Mode0 3 − 2 SHM2 1 SHM1 0 SHM0 Table 26 Description of OSMOD bits (see note ) BIT 7 SYMBOL Wc DESCRIPTION If Wc = 1, then each displayed character is horizontally terminated after 12 bits have been output, as opposed to after 14 bits if Wc = 0. This allows text to be ‘packed’ more tightly so that more characters can be displayed per line. In effect, the 2 bits out of the display ROM, which would otherwise be the rightmost 2 of the 14, are ignored when Wc is 1. Clearly, if this feature is to be used, it must be accounted for in the design of the bit maps in the display ROM. Reserved. Display mode select bits; see Table 27. Reserved. Shadowing mode (ShMode); determines how characters are shadowed in rows for which the row attribute Sh = 1 (register OSAT; see Table 21); for the shadowing modes see Fig.8 and Table 28. 6 5 4 3 2 to 0 − Mode1 Mode0 − SHM2 to SHM0 Table 27 Selection of Display Modes Mode1 Mode0 0 0 1 0 1 0 DISPLAY MODE Mode 0 The OSD feature is disabled. VCLK oscillator is disabled, VID2 to VID0 are set to black, and VCTRL is held inactive.This is the mode to which the 83C055 OSD logic is reset; note 1. Mode 1 The VCLK oscillator is enabled and the OSD logic operates normally internally, but VID2 to VID0 are set to black and VCTRL is held inactive; note 2. Mode 2 Normal OSD operation. Active characters can be shown against TV video (for characters with B = 0) or (for characters with B = 1) against a background of the colour defined as an attribute of BSpace and SplitBSpace characters. Mode 3 Characters can be displayed but all of the receiver’s normal video is inhibited by holding VCTRL asserted throughout the active portion of each scan line; see note 3. 1 Notes 1 1. A direct transition from this mode to ‘active display’ (Mode1, Mode0 = 1X) would result in undefined operation and visual effects for the duration of the current video field (until the next VSYNC). 2. The OSD feature can be toggled between this state and ‘active display’ as desired to achieve real-time special effects such as ‘vertical wiping’. 3. Since VID2 to VID0 are driven with the current background colour during this time, except during the foreground portion of displayed characters, this produces text against a solid background. This mode is useful for extensive displays that require user concentration. 1996 Mar 22 23 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 83C145; 83C845 83C055; 87C055 Table 28 Shadowing modes determined by bits SHM2 to SHM0 (register OSMOD) and Sh (register OSAT) SHM2 0 0 0 0 1 1 1 1 X Note 1. The mode names are based on the position of an apparent light source, ranging from the lower left (South-west) clockwise to the lower right (South-east); see Fig.8. 13.9 OSD Control Register OSORG SHM1 0 0 1 1 0 0 1 1 X SHM0 0 1 0 1 0 1 0 1 X Sh 1 1 1 1 1 1 1 1 0 South-west West North-west North North-east East South-east Full surround No Shadowing SHADOWING MODE(1) Table 29 OSD Control Register OSORG (address C2H) 7 HS4 6 HS3 5 HS2 4 HS1 3 HS0 2 VS2 1 VS1 0 VS0 Table 30 Description of OSORG bits (note 1) BIT 7 to 3 SYMBOL HS4 to HS0 DESCRIPTION HStart field; defines the horizontal start position of all the on-screen character rows, as approximately a multiple of 4 VCLK clock cycles. Active display begins after the trailing edge of HSYNC at the position: HP = [ 4 × ( HStart ) + 1 ] × VCLK clock cycle + ( one single-sized character width ) Where (HStart) is the decimal value of bits (HS4 to HS0); note 2. 2 to 0 VS2 to VS0 VStart field; defines the vertical start position of the first on-screen character row, as approximately a multiple of 4 HSYNC pulses. Active display begins after the field’s time reference point (a range of 3 to 31)at the position: VP = [ 4 × ( VStart ) – 1 ] × HSYNC pulses Where (VStart) is the decimal value of bits (VS2 to VS0); note 3. Notes 1. Neither the Hstart nor Vstart parameter is affected by the D line attribute that is used to display double-sized characters. 2. Counting variations in Wc, there may be 17 to 143 VCLK clock cycles from the end of HSYNC to the start of the first character of each row. 3. Subsequent character rows occur directly below the first, such that the last scan line of one row is directly followed by the first scan line of the next row. Successive New Line characters (with or without the Short Row designation) can be used to vertically separate text rows on the screen. 1996 Mar 22 24 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 83C145; 83C845 83C055; 87C055 handbook, full pagewidth foreground colour pixel black pixel background colour pixel apparent light source ShMode = 010 ShMode = 011 ShMode = 100 ShMode = 001 No Shadowing ShMode = 101 ShMode = 000 ShMode = 111 ShMode = 110 MBE773 ShMode = (SHM2, SHM1, SHM0) Fig.8 Effect of shadowing on the letter ‘E’. 1996 Mar 22 25 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 14 PROGRAMMING CONSIDERATIONS 14.1 EPROM Characteristics 83C145; 83C845 83C055; 87C055 The 87C055 is programmed by using a modified Quick-Pulse Programming algorithm similar to that used for devices such as the 87C751. It differs from these devices in that a serial data stream is used to place the 87C055 in the programming mode. Figure 9 shows a block diagram of the programming configuration for the 87C055. Table 31 Pin usage for Programming PIN XTAL1 RESET USAGE Oscillator input and receives the master system clock. This clock should be between 1.2 and 6 MHz. Used to accept the serial data stream that places the 87C055 into various programming modes. This pattern consists of a 10-bit code with the LSB sent first. Each bit is synchronized to the clock input, XTAL1. Port 0 VPP/TDAC/P0.0 Port 2 P2.7 to P2.0 Port 3 P3.7 to P3.0 Used as a bidirectional data bus during programming and verify operations. During programming mode, it accepts the byte to be programmed. During verify mode, it provides the contents of the EPROM location specified by the address which has been supplied to Port 2. Address input for the byte to be programmed and accepts both the high- and low-order components of the 11-bit address; note 1. Used as the programming voltage supply input (VPP signal). PROG/PWM1/P0.1 Used as the program PROG signal. This pin is used for the 25 programming pulses. Note 1. Multiplexing of these address components is performed using the ASEL input: a) ASEL input is driven HIGH and then drive Port 2 with the high-order bits of the address. ASEL should remain HIGH for at least 13 clock cycles. b) ASEL may then be driven LOW which latches the high-order bits of the address internally. The high-order address should remain on Port 2 for at least 2 clock cycles after ASEL is driven LOW. c) Port 2 may then be driven with the low byte of the address. The low-order address will be internally stable 13 clock cycles later. The address will remain stable provided that the low byte placed on Port 2 is held stable and ASEL is kept LOW. d) ASEL needs to be pulsed HIGH only to change the high byte of the address. 1996 Mar 22 26 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 14.2 Programming operation 14.3 83C145; 83C845 83C055; 87C055 Erasure Characteristics Figures 10 and 11 show the timing diagrams for the Program/Verify cycle. Programming operation: 1. RST should initially be held HIGH for at least 2 machine cycles. P0.1 (PROG) and P0.0 (VPP) will be at VOH as a result of the RST operation. At this point, these pins function as normal quasi-bidirectional I/O ports and the programming equipment may pull these lines LOW. However, prior to sending the 10-bit code on the RST pin, the programming equipment should drive these pins HIGH (VIH). 2. The RST pin may now be used as the serial data input for the data stream which places the 87C055 in the Programming Mode. Data bits are sampled during the clock HIGH time and thus should only change during the time that the clock is LOW. Following transmission of the last data bit, the RST pin should be held LOW. 3. Next the address information for the location to be programmed is placed on Port 2 and ASEL is used to perform the address multiplexing, as previously described (see Table 31; note 1). a) At this time, Port 1 functions as an output. b) A high voltage VPP level is then applied to the VPP input (P0.0). This sets Port 1 as an input port. c) The data to be programmed into the EPROM array is then placed on Port 3. This is followed by a series of programming pulses applied to the PROG pin (P0.1). These pulses are created by driving P0.1 LOW and then HIGH. This pulse is repeated until a total of 25 programming pulses have occurred. At the conclusion of the last pulse, the PROG signal should remain HIGH. 4. The VPP signal may now be driven to the VOH level, placing the 87C055 in the Verify Mode; Port 3 is now used as an output port. After four machine cycles (48 clock periods), the contents of the addressed location in the EPROM array will appear on Port 3. 5. The next programming cycle may now be initiated by: a) Placing the address information at the inputs of the multiplexed buffers. b) Driving the VPP pin to the VPP voltage level. c) Providing the byte to be programmed to Port 3 and issuing the 26 programming pulses on the PROG pin. d) Bringing VPP back down to the VOH level and verifying the byte (see Table 33). Erasure of the EPROM begins to occur when the chip is exposed to light with wavelengths shorter than approximately 4000 Angstroms. Since sunlight and fluorescent lighting have wavelengths in this range, exposure to these light sources over an extended time (about 1 week in sunlight, or 3 years in room level fluorescent lighting) could cause inadvertent erasure. For this and secondary effects, it is recommended that an opaque label be placed over the window. For elevated temperature or environments where solvents are being used, apply Kapton tape Fluorless (part number 2345-5) or equivalent. The recommended erasure procedure is exposure to ultraviolet light (at 2537 Angstroms) to an integrated dose of at least 15 Ws/cm2. Exposing the EPROM to an ultraviolet lamp of 12000 µW/cm2 rating for 20 to 39 minutes, at a distance of about 1 inch, should be sufficient. Erasure leaves the array in an all logic 1s state. 14.4 Reading Signature Bytes The Signature Bytes are read by the same procedure as a normal verify of locations 30H and 31H (the values are shown in Table 32), except that the serial code indicated in Table 33 for reading signature bytes should be used. Table 32 Programming and Verification codes ADDRESS 30H 31H CONTENT 15H 4BH INDICATION manufactured by Philips 87C055 Table 33 Implementing Program/Verify Modes OPERATION Program user EPROM Verify user EPROM Read Signature Bytes Note 1. Pulsed from VIH to VIL and returned to VIH. SERIAL P0.1 CODE (PROG) 286H 286H 280H −(1) VIH VIH P0.0 (VPP) VPP VIH VIH 1996 Mar 22 27 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 83C145; 83C845 83C055; 87C055 handbook, full pagewidth 8 A0-A15 ADDRESS STROBE PROGRAMMING PULSES VPP/VIH VOLTAGE SOURCE CLK SOURCE RESET CONTROL LOGIC P2.0-2.7 P0.2/ASEL P0.1 VDD VSS 5V 87C055 P0.0 P3.0-P3.7 XTAL1 8 DATA BUS RESET MBE767 Fig.9 Programming Configuration. handbook, full pagewidth XTAL1 min 2 machine cycles 10-bit serial code RESET BIT 0 BIT 1 BIT 2 BIT 3 BIT 4 BIT 5 BIT 6 BIT 7 BIT 8 BIT 9 P0.0 undefined P0.1 undefined MBE768 Fig.10 Entry into Program/Verify Modes. 1996 Mar 22 28 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 14.5 EPROM Programming and Verification VDD = 5 V ±10%; VSS = 0 V; Tamb = 21 to 27 °C. SYMBOL 1/tCLCL tAVGL(1) tGHAX tDVGL tGHDX tSHGL tGHSL tGLGH tAVQV(1) tGHGL tSYNL tSYNH tMASEL tHAHLD tHASET tADSTA Note 1. Address should be valid at least 24tCLCL before the rising edge of P0.0 (VPP). PARAMETER Oscillator/clock frequency Address setup to P0.1 (PROG) LOW Address hold after P0.1 (PROG) HIGH Data setup to P0.1 (PROG) LOW Data hold after P0.1 (PROG) HIGH VPP setup to P0.1 (PROG) LOW VPP hold after P0.1 (PROG) HIGH P0.1 (PROG) width VPP (VDD) LOW to data valid P0.1 (PROG) HIGH to P0.1 (PROG) LOW P0.0 (sync pulse) LOW P0.0 (sync pulse) HIGH ASEL HIGH time Address hold time Address setup to ASEL Low address to address stable MIN. 1.2 10 + 24tCLCL 48tCLCL 38tCLCL 36tCLCL 10 10 90 − 10 4tCLCL 8tCLCL 13tCLCL 2tCLCL 13tCLCL 13tCLCL 83C145; 83C845 83C055; 87C055 MAX. 6 − − − − − − 110 48tCLCL − − − − − − − UNIT MHz µs µs µs µs µs µs µs µs µs µs µs µs µs µs µs handbook, full pagewidth 12.75 V 5V tSHGL 25 PULSES 5V tGHSL P0.0 [V (p-p)] P0.1 (PROG) tGLGH 98µs MIN 10µs MIN tGHGL tMASEL P0.2 (ASEL) tHASET tHAHLD LOW ADDRESS tDVGL tGHDX tAVQV INVALID DATA VALID DATA PORT 2 HIGH ADDRESS tADSTA PORT 3 INVALID DATA verify mode VALID DATA DATA TO BE PROGRAMMED program mode verify mode MBE769 Fig.11 Program/Verify cycle. 1996 Mar 22 29 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 15 PROGRAMMING THE OSD EPROM 15.1 Overview 83C145; 83C845 83C055; 87C055 Each character is 14 bits wide by 18 lines high.A character is split about a vertical axis into two sections UPPER and LOWER as illustrated in Table 34: • Each section contains 7 bits of the character, such that: – the LOWER section contains bits 7 to 1, and – the UPPER section contains bits 14 to 8. • The LOWER section of the character is programmed when the LSB of the program address equals a logic 0, and the UPPER section when the LSB equals a logic 1. During Programming and Verification, each section is programmed using bytes of program data. The MSB of the program data is not used; however, the MSB location physically exists, and so will Program and Verify. The OSD EPROM space starts at location C000H and ends at location CFFFH. However, due to the addressing scheme of the OSD, not all locations within this space are used.The start location of the next character can be calculated by adding 40H to the start location of the previous character. For example, character 1 starts at C000H; then characters 2, 3, and 4 start at C040H, C080H, and C0C0H, respectively. 15.2 Character description and programming An example of an OSD character bit map, and the program data to obtain that character is shown in Table 34. 15.3 OSD EPROM bit map The mapping for the full OSD EPROM is shown in Table 35. To program the example character into the first character location of the OSD EPROM would require the data at the address as shown in Table 34. Table 34 Example of an OSD Character Bit Map (note 1) CHARACTER BIT MAP LINE Line 1 Line 2 Line 3 Line 4 Line 5 Line 6 Line 7 Line 8 Line 9 Line 10 Line 11 Line 12 Line 13 Line 14 Line 15 Line 16 Line 17 Line 18 Note 1. X can be a logic 0 or logic 1, and will Program and Verify correctly. UPPER (BIT 14 TO 8) 0000000 0000000 0011110 0011110 0011110 0011110 0011110 0011110 0011111 0011111 0011111 0011110 0011110 0011110 0011110 0011110 0000000 0000000 LOWER (BIT 7 TO 1) 0000000 0000000 0001100 0001100 0001100 0001100 0001100 0001100 1111100 1111100 1111100 0001100 0001100 0001100 0001100 0001100 0000000 0000000 PROGRAM DATA UPPER X0000000 X0000000 X0011110 X0011110 X0011110 X0011110 X0011110 X0011110 X0011111 X0011111 X0011111 X0011110 X0011110 X0011110 X0011110 X0011110 X0000000 X0000000 LOWER X0000000 X0000000 X0001100 X0001100 X0001100 X0001100 X0001100 X0001100 X1111100 X1111100 X1111100 X0001100 X0001100 X0001100 X0001100 X0001100 X0000000 X0000000 ADDRESS (HEX) UPPER C001 C003 C005 C007 C009 C00B C00D C00F C011 C013 C015 C017 C019 C01B C01D C01F C021 C023 LOWER C000 C002 C004 C006 C008 C00A C00C C00E C010 C012 C014 C016 C018 C01A C01C C01E C020 C022 1996 Mar 22 30 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) Table 35 OSD EPROM Bit Map ADDRESS (HEX) CHARACTER NO. LOWER BYTE 0 C000 C002 C004 C006 C008 C00A C00C C00E C010 C012 C014 C016 C018 C01A C01C C01E C020 C022 C024 to C03F 1(1) 2(1) 3 to 59(1) C040 to C063 C064 to C07F C080 to C0A3 C0A4 to C0BF − CF00 to CF23 CF24 to CF3F 61(2) 62(2) 63(2) CF40 to CF63 CF64 to CF7F CF80 to CFA3 CFA4 to CFBF CFC0 to CFE3 CFE4 to CFFF Notes 60(2) UPPER BYTE C001 C003 C005 C007 C009 C00B C00D C00F C011 C013 C015 C017 C019 C01B C01D C01F C021 C023 83C145; 83C845 83C055; 87C055 CHARACTER LINE NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 not used 1 to 18 not used 1 to 18 not used − 1 to 18 not used 1 to 18 not used 1 to 18 not used 1 to 18 not used 1. Characters 1 to 59 are setup in the similar way as character 0; due to space and simplicity this is not fully displayed. 2. Locations 60, 61, 62 and 63 should be programmed to logic 0s. The character names are: character no. 60 = Normal Space; character no. 61 = New Line; character no. 62 = BSpace; character no. 63 = SplitBSpace. 1996 Mar 22 31 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 16 REGISTER MAP 83C145; 83C845 83C055; 87C055 Table 36 Register map Values within parenthesis show the bit state after a reset operation; ‘X’ denotes an undefined state. ADDR. (HEX) E0 F0 83 82 A8 9A REGISTER ACC(1) B(1) DPH DPL IE(1) OSAD 7 ACC7 (0) B7 (0) DPH7 (0) DPL7 (0) EA (0) − (X) − (X) − (X) − (X) − (X) IV (X) Wc (X) HS4 (X) P07 (1) P17 (1) P27 (1) P37 (1) − (0) CY (0) PW0E (0) 6 ACC6 (0) B6 (0) DPH6 (0) DPL6 (0) − (X) OSAD6 (X) − (X) − (X) − (X) − (X) Pv (X) − (X) HS3 (X) P06 (1) P16 (1) P26 (1) P36 (1) − (X) AC (0) − (0) 5 ACC5 (0) B5 (0) DPH5 (0) DPL5 (0) − (0) OSAD5 (X) − (X) − (X) − (X) OSDT5 (X) Lv (X) Mode1 (X) HS2 (X) P05 (1) P15 (1) P25 (1) P35 (1) − (X) F0 (0) PV05 (0) 4 ACC4 (0) B4 (0) DPH4 (0) DPL4 (0) EVS (0) OSAD4 (X) E (X) B (X) B (X) OSDT4 (X) Ph (X) Mode0 (X) HS1 (X) P04 (1) P14 (1) P24 (1) P34 (1) − (X) RS1 (0) PV04 (0) 3 ACC3 (0) B3 (0) DPH3 (0) DPL3 (0) ET1 (0) OSAD3 (X) − (X) − (X) − (X) OSDT3 (X) Pc (X) − (X) HS0 (X) P03 (1) P13 (1) P23 (1) P33 (1) GF1 (X) RS0 (0) PV03 (0) 2 ACC2 (0) B2 (0) DPH2 (0) DPL2 (0) EX1 (0) OSAD2 (X) SR (X) BC2 (X) FC2 (X) OSDT2 (X) Po (X) SHM2 (X) VS2 (X) P02 (1) P12 (1) P22 (1) P32 (1) GF0 (X) OV (0) PV02 (0) 1 ACC1 (0) B1 (0) DPH1 (0) DPL1 (0) ET0 (0) OSAD1 (X) D (X) BC1 (X) FC1 (X) OSDT1 (X) DH (X) SHM1 (X) VS1 (X) P01 (1) P11 (1) P21 (1) P31 (1) − (X) − (0) PV01 (0) 0 ACC0 (0) B0 (0) DPH0 (0) DPL0 (0) EX0 (0) OSAD0 (X) Sh (X) BC0 (X) FC0 (X) OSDT0 (X) BFe (X) SHM0 (X) VS0 (X) P00 (1) P10 (1) P20 (1) P30 (1) − (X) P (0) PV00 (0) 9F to 98 OSAT(1)(2) OSAT(1)(3) OSAT(1)(4) 99 C0 C1 C2 80 90 A0 B0 87 D0 D4 OSDT OSCON(1) OSMOD OSORG P0(1) P1(1) P2(1) P3(1) PCON PSW(1) PWM0 1996 Mar 22 32 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 83C145; 83C845 83C055; 87C055 4 PV14 (0) PV24 (0) PV34 (0) PV44 (0) PV54 (0) PV64 (0) PV74 (0) St (0) SP4 (0) TD12 (0) TD2 (0) TR0 (0) TH04 (0) TH14 (0) TL04 (0) TL14 (0) M0 (0) 3 PV13 (0) PV23 (0) PV33 (0) PV43 (0) PV53 (0) PV63 (0) PV73 (0) SAD3 (0) SP3 (0) TD11 (0) TD3 (0) IE1 (0) TH03 (0) TH13 (0) TL03 (0) TL13 (0) GATE (0) 2 PV12 (0) PV22 (0) PV32 (0) PV42 (0) PV52 (0) PV62 (0) PV72 (0) SAD2 (0) SP2 (0) TD10 (0) TD4 (0) IT1 (0) TH02 (0) TH12 (0) TL02 (0) TL12 (0) C/T (0) 1 PV11 (0) PV21 (0) PV31 (0) PV41 (0) PV51 (0) PV61 (0) PV71 (0) SAD1 (0) SP1 (0) TD9 (0) TD5 (0) IE0 (0) TH01 (0) TH11 (0) TL01 (0) TL11 (0) M1 (0) 0 PV10 (0) PV20 (0) PV30 (0) PV40 (0) PV50 (0) PV60 (0) PV70 (0) SAD0 (0) SP0 (0) TD8 (0) TD6 (0) IT0 (0) TH00 (0) TH10 (0) TL00 (0) TL10 (0) M0 (0) ADDR. (HEX) D5 D6 D7 DC DD DE DF D8 81 D3 D2 8F 8C 8D 8A 8B 89 C3 C4 Notes REGISTER PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7 SAD(1) SP TDACH TDACL TCON(1) TH0 TH1 TL0 TL1 TMOD RAMCHR RAMATT 7 PW1E (0) PW2E (0) PW3E (0) PW4E (0) PW5E (0) PW6E (0) PW7E (0) VHi (0) SP7 (0) TDE (0) TD7 (0) TF1 (0) TH07 (0) TH17 (0) TL07 (0) TL17 (0) GATE (0) 6 − (0) − (0) − (0) − (0) − (0) − (0) − (0) CH1 (0) SP6 (0) − (0) TD0 (0) TR1 (0) TH06 (0) TH16 (0) TL06 (0) TL16 (0) C/T (0) 5 PV15 (0) PV25 (0) PV35 (0) PV45 (0) PV55 (0) PV65 (0) PV75 (0) CH0 (0) SP5 (0) TD13 (0) TD1 (0) TF0 (0) TH05 (0) TH15 (0) TL05 (0) TL15 (0) M1 (0) for test purposes only for test purposes only 1. Bit addressable. 2. With OSDT = New Line. 3. With OSDT = BSpace or SplitBSpace. 4. With OSDT = Any other character. 1996 Mar 22 33 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 17 LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 34); see notes 1 and 2. SYMBOL VDD VI IOH IOL Ptot Tamb Tstg Notes supply voltage input voltage on any pin with respect to ground (VSS) maximum source current for all port lines maximum sink current for all port lines total power dissipation operating ambient temperature storage temperature PARAMETER MIN. 4.5 −0.5 − − − 0 −65 83C145; 83C845 83C055; 87C055 MAX. 5.5 6.5 −1.5 15 1.5 70 150 V V UNIT mA mA W °C °C 1. Stresses above those listed under Limiting Values may cause permanent damage to the device. 2. Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to VSS unless otherwise noted. 18 HANDLING Inputs and outputs are protected against electrostatic discharge in normal handling. However it is good practice to take normal precautions appropriate to handling MOS devices (see “Handling MOS devices” ). 1996 Mar 22 34 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 83C145; 83C845 83C055; 87C055 19 DC CHARACTERISTICS VDD = 5 V ±10% Tamb = 0 to +70 °C; all voltages with respect to VSS; unless otherwise specified. SYMBOL Supply VDD IDD VIL VIL1 VIH VIH1 VIH2 VIH3 operating supply voltage operating supply current LOW level input voltage LOW level input voltage; VSYNC and HSYNC HIGH level input voltage; XTAL, VCLK1 and RST HIGH level input voltage; P1.2 to P1.0, P3.6 to P3.5 and P3.3 to P3.1 HIGH level input voltage; P1.3, P3.7,P3.4 and P3.0 HIGH level input voltage; VSYNC and HSYNC note 2 VDD = 5.5 V; note 1 4.5 − −0.5 −0.5 0.7VDD 5.0 − − − − 5.5 30 0.15VDD VDD + 0.5 VDD + 0.5 12.6 VDD + 0.5 VDD + 0.5 V mA V V V V V V PARAMETER CONDITIONS MIN. TYP. MAX. UNIT 0.2VDD − 0.1 V 0.2VDD + 0.9 − 0.2VDD + 0.9 − 0.67VDD 0.7VDD − − VIH − VDD HIGH level input voltage with respect to VDD; Port 0, P1.3, P3.7, P3.4 and P3.0 VOL1 VOL2 VOL3 VOH RRST CIO HYS Notes LOW level output voltage; P2.7 to P2.0 IOL = 10 mA; note 3 and P3.6 to P3.5 LOW level output voltage; TDAC and PWM0 to PWM7 LOW level output voltage; all other outputs HIGH level output voltage; Port 1, VID2 to VID0, VCTRL and BF Reset (RST) pull-down resistor Pin capacitance; except P0.0 and P0.7 test freq. = 1 MHz; Tamb = 25 °C; note 5 Hysteresis; VSYNC and HSYNC IOL = 700 µA; note 4 IOL = 1.6 mA IOH = −60 µA − − − 2.4 50 − 0.8 − − − − − − − 0.5 0.5 0.45 − 300 10 − V V V V kΩ pF V 1. IDD measured with OSD block initialized and RST remaining LOW. 2. This maximum applies at all times, including during power switching, and must be accounted for in power supply design. During a Power-on process, the +12 V source used for external pull-up resistors should not precede the VDD of the 83C055 up their respective voltage ramps by more than this margin, nor, during a Power-down process, should VDD precede +12 V down their respective voltage ramps by more than this margin. 3. No more than 6 (any 6) of these 10 high current outputs may be used at the VOL1 (IOL = 10 mA) specification. The other 4 should comply with the VOL3 specification (IOL = 1.6 mA). 4. The specified current rating applies when any of these pins is used as a Pulse Width Modulated (PWM) output. For use as a port output, the rating is as given subsequently. 5. The capacitance of pins P0.0 and P0.7 for the 87C055 exceeds 10 pF; for P0.0 this is maximum 40 pF, while for P0.7 it is maximum 20 pF. 1996 Mar 22 35 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 83C145; 83C845 83C055; 87C055 20 AC CHARACTERISTICS VDD = 5 V ±10%; Tamb = 0 to +70 °C; all voltages with respect to VSS; unless otherwise specified. SYMBOL 1/tCLCL tCHCX tCLCX tCLCH tCHCL 1/tVCLCL tVCOH − tVCOL tVCOH1 − tVCOH2 tVCOL1 − tVCOL2 Notes 1. The 83C055 is tested at its maximum XTAL frequency, but not at any other (lower) rate. 2. These parameters apply only when an external clock signal is used. 3. These parameters assume equal loading at CL = 100 pF, for all the referenced outputs. These parameters are specified but not tested. XTAL frequency XTAL1 clock HIGH time XTAL1 clock LOW time XTAL1 clock rise time XTAL1 clock fall time VCLK frequency Rise versus fall time skew on any one of VID2 to VID0, VCTRL and BF Rise time skew between any two of VID2 to VID0, VCTRL and BF Fall time skew between any two of VID2 to VID0, VCTRL and BF note 3 PARAMETER CONDITIONS note 1 note 2 MIN. 6 20 20 − 5 5 − − − TYP. − − − − − − − − − MAX. 12 − − 20 20 8 40 30 30 UNIT MHz ns ns ns ns MHz ns ns ns 1996 Mar 22 36 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 21 PACKAGE OUTLINES SDIP42: plastic shrink dual in-line package; 42 leads (600 mil) 83C145; 83C845 83C055; 87C055 SOT270-1 seating plane D ME A2 A L A1 c Z e b1 wM (e 1) MH b 42 22 pin 1 index E 1 21 0 5 scale 10 mm DIMENSIONS (mm are the original dimensions) UNIT mm A max. 5.08 A1 min. 0.51 A2 max. 4.0 b 1.3 0.8 b1 0.53 0.40 c 0.32 0.23 D (1) 38.9 38.4 E (1) 14.0 13.7 e 1.778 e1 15.24 L 3.2 2.9 ME 15.80 15.24 MH 17.15 15.90 w 0.18 Z (1) max. 1.73 Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT270-1 REFERENCES IEC JEDEC EIAJ EUROPEAN PROJECTION ISSUE DATE 90-02-13 95-02-04 1996 Mar 22 37 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) 22 SOLDERING 22.1 Introduction 83C145; 83C845 83C055; 87C055 There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these cases reflow soldering is often used. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our “IC Package Databook” (order code 9398 652 90011). 22.2 Soldering by dip or wave The device may be mounted to the seating plane, but the temperature of the plastic body must not exceed the specified storage maximum. If the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. 22.3 Repairing soldered joints Apply a low voltage soldering iron (less than 24 V) to the lead(s) of the package, below the seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is less than 300 °C it may remain in contact for up to 10 seconds. If the bit temperature is between 300 and 400 °C, contact may be up to 5 seconds. The maximum permissible temperature of the solder is 260 °C; solder at this temperature must not be in contact with the joint for more than 5 seconds. The total contact time of successive solder waves must not exceed 5 seconds. 23 DEFINITIONS Data sheet status Objective specification Preliminary specification Product specification Limiting values Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. 24 LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. This data sheet contains target or goal specifications for product development. This data sheet contains preliminary data; supplementary data may be published later. This data sheet contains final product specifications. 1996 Mar 22 38 Philips Semiconductors Product specification Microcontrollers for TV and video (MTV) NOTES 83C145; 83C845 83C055; 87C055 1996 Mar 22 39 Philips Semiconductors – a worldwide company Argentina: see South America Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113, Tel. (02) 805 4455, Fax. (02) 805 4466 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. (01) 60 101-1256, Fax. (01) 60 101-1250 Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6, 220050 MINSK, Tel. (172) 200 733, Fax. (172) 200 773 Belgium: see The Netherlands Brazil: see South America Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor, 51 James Bourchier Blvd., 1407 SOFIA, Tel. (359) 2 689 211, Fax. (359) 2 689 102 Canada: PHILIPS SEMICONDUCTORS/COMPONENTS: Tel. (800) 234-7381, Fax. (708) 296-8556 Chile: see South America China/Hong Kong: 501 Hong Kong Industrial Technology Centre, 72 Tat Chee Avenue, Kowloon Tong, HONG KONG, Tel. (852) 2319 7888, Fax. (852) 2319 7700 Colombia: see South America Czech Republic: see Austria Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S, Tel. (032) 88 2636, Fax. (031) 57 1949 Finland: Sinikalliontie 3, FIN-02630 ESPOO, Tel. (358) 0-615 800, Fax. (358) 0-61580 920 France: 4 Rue du Port-aux-Vins, BP317, 92156 SURESNES Cedex, Tel. (01) 4099 6161, Fax. (01) 4099 6427 Germany: P.O. Box 10 51 40, 20035 HAMBURG, Tel. (040) 23 53 60, Fax. (040) 23 53 63 00 Greece: No. 15, 25th March Street, GR 17778 TAVROS, Tel. (01) 4894 339/4894 911, Fax. (01) 4814 240 Hungary: see Austria India: Philips INDIA Ltd, Shivsagar Estate, A Block, Dr. Annie Besant Rd. Worli, BOMBAY 400 018 Tel. (022) 4938 541, Fax. (022) 4938 722 Indonesia: see Singapore Ireland: Newstead, Clonskeagh, DUBLIN 14, Tel. (01) 7640 000, Fax. (01) 7640 200 Israel: RAPAC Electronics, 7 Kehilat Saloniki St, TEL AVIV 61180, Tel. (03) 645 04 44, Fax. (03) 648 10 07 Italy: PHILIPS SEMICONDUCTORS, Piazza IV Novembre 3, 20124 MILANO, Tel. (0039) 2 6752 2531, Fax. (0039) 2 6752 2557 Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108, Tel. (03) 3740 5130, Fax. (03) 3740 5077 Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL, Tel. (02) 709-1412, Fax. (02) 709-1415 Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR, Tel. (03) 750 5214, Fax. (03) 757 4880 Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905, Tel. 9-5(800) 234-7831, Fax. (708) 296-8556 Middle East: see Italy Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB, Tel. (040) 2783749, Fax. (040) 2788399 New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND, Tel. (09) 849-4160, Fax. (09) 849-7811 Norway: Box 1, Manglerud 0612, OSLO, Tel. (022) 74 8000, Fax. (022) 74 8341 Philippines: PHILIPS SEMICONDUCTORS PHILIPPINES Inc., 106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI, Metro MANILA, Tel. (63) 2 816 6380, Fax. (63) 2 817 3474 Poland: Ul. Lukiska 10, PL 04-123 WARSZAWA, Tel. (022) 612 2831, Fax. (022) 612 2327 Portugal: see Spain Romania: see Italy Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231, Tel. (65) 350 2000, Fax. (65) 251 6500 Slovakia: see Austria Slovenia: see Italy South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale, 2092 JOHANNESBURG, P.O. Box 7430 Johannesburg 2000, Tel. (011) 470-5911, Fax. (011) 470-5494 South America: Rua do Rocio 220 - 5th floor, Suite 51, CEP: 04552-903-SÃO PAULO-SP, Brazil, P.O. Box 7383 (01064-970), Tel. (011) 821-2333, Fax. (011) 829-1849 Spain: Balmes 22, 08007 BARCELONA, Tel. (03) 301 6312, Fax. (03) 301 4107 Sweden: Kottbygatan 7, Akalla. S-16485 STOCKHOLM, Tel. (0) 8-632 2000, Fax. (0) 8-632 2745 Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH, Tel. (01) 488 2211, Fax. (01) 481 77 30 Taiwan: PHILIPS TAIWAN Ltd., 23-30F, 66, Chung Hsiao West Road, Sec. 1, P.O. Box 22978, TAIPEI 100, Tel. (886) 2 382 4443, Fax. (886) 2 382 4444 Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd., 209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260, Tel. (66) 2 745-4090, Fax. (66) 2 398-0793 Turkey: Talatpasa Cad. No. 5, 80640 GÜLTEPE/ISTANBUL, Tel. (0212) 279 2770, Fax. (0212) 282 6707 Ukraine: PHILIPS UKRAINE, 2A Akademika Koroleva str., Office 165, 252148 KIEV, Tel. 380-44-4760297, Fax. 380-44-4766991 United Kingdom: Philips Semiconductors LTD., 276 Bath Road, Hayes, MIDDLESEX UB3 5BX, Tel. (0181) 730-5000, Fax. (0181) 754-8421 United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409, Tel. (800) 234-7381, Fax. (708) 296-8556 Uruguay: see South America Vietnam: see Singapore Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD, Tel. (381) 11 825 344, Fax. (359) 211 635 777 Internet: http://www.semiconductors.philips.com/ps/ For all other countries apply to: Philips Semiconductors, Marketing & Sales Communications, Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31-40-2724825 SCDS48 © Philips Electronics N.V. 1996 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Printed in The Netherlands 457041/1100/01/pp40 Document order number: Date of release: 1996 Mar 22 9397 750 00752