BU2730

Philips Semiconductors Preliminary specification Silicon Diffused Power Transistor BU2730AL GENERAL DESCRIPTION New generation, high-voltage, high-speed switching npn transistor in a plastic envelope intended for use in horizontal deflection circuits of large screen colour television receivers. QUICK REFERENCE DATA SYMBOL VCESM VCEO IC ICM Ptot VCEsat ICsat ts PARAMETER Collector-emitter voltage peak value Collector-emitter voltage (open base) Collector current (DC) Collector current peak value Total power dissipation Collector-emitter saturation voltage Collector saturation current Storage time CONDITIONS VBE = 0 TYP. 9 3.5 MAX. 1700 825 16 40 125 5.0 4.5 UNIT V V A A W V A µs Tmb ≤ 25 ˚C IC = 9 A; IB = 1.8 A f = 32 kHz ICsat = 9 A; f = 32 kHz PINNING - SOT430 PIN 1 2 3 base collector emitter DESCRIPTION PIN CONFIGURATION SYMBOL c b 1 2 3 heat collector sink e LIMITING VALUES Limiting values in accordance with the Absolute Maximum Rating System (IEC 134) SYMBOL VCESM VCEO IC ICM IB IBM -IB(AV) -IBM Ptot Tstg Tj PARAMETER Collector-emitter voltage peak value Collector-emitter voltage (open base) Collector current (DC) Collector current peak value Base current (DC) Base current peak value Reverse base current Reverse base current peak value 1 Total power dissipation Storage temperature Junction temperature CONDITIONS VBE = 0 V MIN. -55 MAX. 1700 825 16 40 10 15 200 10 125 150 150 UNIT V V A A A A mA A W ˚C ˚C average over any 20 ms period Tmb ≤ 25 ˚C THERMAL RESISTANCES SYMBOL Rth j-mb Rth j-a PARAMETER Junction to mounting base Junction to ambient CONDITIONS in free air TYP. 35 MAX. 1.0 UNIT K/W K/W 1 Turn-off current. April 1997 1 Rev 1.000 Philips Semiconductors Preliminary specification Silicon Diffused Power Transistor BU2730AL STATIC CHARACTERISTICS Tmb = 25 ˚C unless otherwise specified SYMBOL ICES ICES IEBO BVEBO VCEsat VBEsat hFE hFE PARAMETER Collector cut-off current 2 CONDITIONS VBE = 0 V; VCE = VCESMmax VBE = 0 V; VCE = VCESMmax; Tj = 125 ˚C VEB = 7.5 V; IC = 0 A IB = 1 mA IC = 9 A; IB = 1.8 A IC = 9 A; IB = 1.8 A IC = 1 A; VCE = 5 V IC = 9 A; VCE = 5 V MIN. 7.5 5 TYP. 14 0.91 17 7.5 MAX. 1.0 2.0 1.0 5.0 9.5 UNIT mA mA mA V V V Emitter cut-off current Base-emitter breakdown voltage Collector-emitter saturation voltage Base-emitter saturation voltage DC current gain DYNAMIC CHARACTERISTICS Tmb = 25 ˚C unless otherwise specified SYMBOL PARAMETER Switching times (32 kHz line deflection dynamic test circuit). ts tf Turn-off storage time Turn-off fall time CONDITIONS ICsat = 9 A; LC = 200 µH; Cfb = 9 nF; VCC = 142 V; IB(end) = tbf ; -IBM = 4.5 A; -VBB = 4 V; LB = 5 µH TYP. MAX. UNIT 3.5 tbf 4.5 tbf µs µs 2 Measured with half sine-wave voltage (curve tracer). April 1997 2 Rev 1.000 Philips Semiconductors Preliminary specification Silicon Diffused Power Transistor BU2730AL MECHANICAL DATA Dimensions in mm Net Mass: 9 g 20.5 max 3.1 3.5 6.0 4.0 25.5 26.5 10.0 3.0 1.5 seating plane 3.0 5.3 max 3.0 2.5 19.5 min 1.5 2.5 max 3.5 max 0.8 1.0 0.4 M 5.45 5.45 0.8 max 3.0 max Fig.1. SOT430; pin 2 connected to mounting base. April 1997 3 Rev 1.000 Philips Semiconductors Preliminary specification Silicon Diffused Power Transistor BU2730AL DEFINITIONS Data sheet status Objective specification Product specification Limiting values Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of this specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. © Philips Electronics N.V. 1997 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, it is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights. This data sheet contains target or goal specifications for product development. This data sheet contains final product specifications. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. April 1997 4 Rev 1.000