CBT3125DB

INTEGRATED CIRCUITS CBT3125 Quadruple FET bus switch Product data File under Integrated Circuits — ICL03 2001 Dec 12 Philips Semiconductors Philips Semiconductors Product data Quadruple FET bus switch CBT3125 DESCRIPTION The CBT3125 quadruple FET bus switch features independent line switches. Each switch is disabled when the associated Output Enable (OE) input is HIGH. PIN CONFIGURATION 1OE 1A 1B 1 2 3 4 5 6 7 14 VCC 13 4OE 12 4A 11 4B 10 3OE 9 8 3A 3B FEATURES • Standard ’125-type pinout (D, DB, and PW packages) • 5 Ω switch connection between two ports • TTL-compatible input levels • Latch-up testing is done to JESDEC Standard JESD78 which exceeds 500 mA 2OE 2A 2B GND SA00562 Figure 1. SO14, SSOP14, and TSSOP14 • ESD protection exceeds 2000 V HBM per JESD22-A114, 200 V MM per JESD22-A115, and 1000 V CDM per JESD22-C101 NC 1OE 1A 1B 2OE 2A 2B GND 1 2 3 4 5 6 7 8 16 VCC 15 4OE 14 4A 13 4B 12 3OE 11 3A 10 3B 9 NC SA00563 NC = no internal connection Figure 2. SSOP(QSOP)16 ORDERING INFORMATION PACKAGES 14-Pin Plastic SO 14-Pin Plastic SSOP 16-Pin Plastic SSOP(QSOP) 14-Pin Plastic TSSOP TEMPERATURE RANGE –40 to +85 °C –40 to +85 °C –40 to +85 °C –40 to +85 °C ORDER CODE CBT3125D CBT3125DB CBT3125DS CBT3125PW DRAWING NUMBER SOT108-1 SOT337-1 SOT519-1 SOT402-1 Standard packing quantities and other packaging data is available at www.philipslogic.com/packaging. 2001 Dec 12 2 853-2309 27452 Philips Semiconductors Product data Quadruple FET bus switch CBT3125 LOGIC DIAGRAM 1A 2 3 1B FUNCTION TABLE (each bus switch) INPUT OE L FUNCTION A=B disconnect 1OE 1 H 6 2B 2A 5 2OE 4 3A 9 8 3B 3OE 10 4A 12 11 4B 4OE 13 SA00564 Pin numbers shown are for 14-pin package-types. Figure 3. CBT3125 logic diagram (positive logic) ABSOLUTE MAXIMUM RATINGS1 Over operating free-air temperature range, unless otherwise noted. SYMBOL VCC VI IK Tstg supply voltage range input voltage range continuous channel current input clamp current storage temperature range VI/O < 0 see Note 2 PARAMETER CONDITIONS MIN. –0.5 –0.5 — — –65 MAX. 7 7 128 –50 +150 UNIT V V mA mA °C NOTES: 1. Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 3. The package thermal impedance is calculated in accordance with JESD 51-7. RECOMMENDED OPERATING CONDITIONS1 SYMBOL VCC VIH VIL Tamb supply voltage high-level control input voltage low-level control input voltage operating ambient temperature in free-air PARAMETER CONDITIONS MIN. 4.5 2 — –40 MAX. 5.5 — 0.8 +85 UNIT V V V °C NOTE: 1. All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. 2001 Dec 12 3 Philips Semiconductors Product data Quadruple FET bus switch CBT3125 DC ELECTRICAL CHARACTERISTICS Over recommended operating free-air temperature range, unless otherwise noted. SYMBOL VIK II ICC ∆ICC CI CIO(OFF) VP PARAMETER Input clamp voltage Input leakage current Quiescent supply current Additional supply current per input pin (Note 2) Input capacitance Power-off leakage current Pass gate voltage CONDITIONS VCC = 4.5 V; II = –18 mA VCC = 5.5 V; VI = 5.5 V or GND VCC = 5.5 V; IO = 0; VI = VCC or GND control inputs control inputs VCC = 5.5 V; one input at 3.4 V, other inputs at VCC or GND VI = 3 V or 0 VO = 3 V or 0; OE = VCC VCC = 5.0 V; VI = 5.0 V VCC = 4.5 V; VI = 0 V; II = 64 mA ron On-resistance (Note 3) VCC = 4.5 V; VI = 0 V; II = 30 mA VCC = 4.5 V; VI = 2.4 V; II = –15 mA MIN. — — — TYP.1 — — — MAX. –1.2 ±1 3 UNIT V µA µA mA pF pF V Ω Ω Ω — — — — — — — — 1.7 3.4 3.8 5 5 10 2.5 — — — 7 7 15 NOTES: 1. All typical values are at VCC = 5 V, unless otherwise noted. Tamb = 25 °C. 2. This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. 3. Measured by the voltage drop between the A and the B terminals at the indicated current through the switch. On-state resistance is determined by the lower of the voltages of the two (A or B) terminals. AC CHARACTERISTICS Tamb = –40 to +85 °C; CL = 50 pF, unless otherwise noted. SYMBOL tpd ten tdis PARAMETER Propagation delay1 Output enable time to High and Low level Output disable time from High and Low level FROM (INPUT) A or B OE OE TO (OUTPUT) B or A A or B A or B VCC = 5 V ± 0.5 V Min — 1.0 1 Max 0.25 5.4 4.7 ns ns ns UNIT NOTE: 1. This parameter is warranted but not production tested. The propagation delay is based on the RC time constant of the typical on-state resistance of the switch and a load capacitance of 50 pF, when driven by an ideal voltage source (zero output impedance). 2001 Dec 12 4 Philips Semiconductors Product data Quadruple FET bus switch CBT3125 AC WAVEFORMS VM = 1.5 V, VIN = GND to 3.0V 3V 1.5 V INPUT 0V tPLH tPHL VOH 1.5 V OUTPUT VOL 1.5 V 1.5 V TEST CIRCUIT 7V From Output Under Test CL = 50 pF 500 Ω S1 Open GND 500 Ω Load Circuit TEST tpd tPLZ/tPZL tPHZ/tPZH S1 open 7V open SA00028 tPLH and tPHL are the same as tpd. Waveform 1. Input to Output Propagation Delays DEFINITIONS Load capacitance includes jig and probe capacitance; CL = see AC CHARACTERISTICS for value. 3V Output Control 1.5 V 1.5 V 0V 3.5 V Output Waveform 1 S1 at 7 V (see Note) tPZH Output Waveform 2 S1 at Open (see Note) 1.5 V tPHZ VOH – 0.3 V 1.5 V 0V Note: Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. SA00012 tPLZ and tPHZ are the same as tdis. tPZL and tPZH are the same as ten. NOTES: 1. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. 2. The outputs are measured one at a time with one transition per measurement. tPZL tPLZ VOL + 0.3 V VOL VOH SA00558 tPLZ and tPHZ are the same as tdis. tPZL and tPZH are the same as ten. Waveform 2. Output Enable and Disable Times 2001 Dec 12 5 Philips Semiconductors Product data Quadruple FET bus switch CBT3125 SO14: plastic small outline package; 14 leads; body width 3.9 mm SOT108-1 2001 Dec 12 6 Philips Semiconductors Product data Quadruple FET bus switch CBT3125 SSOP14: plastic shrink small outline package; 14 leads; body width 5.3 mm SOT337-1 2001 Dec 12 7 Philips Semiconductors Product data Quadruple FET bus switch CBT3125 SSOP16: plastic shrink small outline package; 16 leads; body width 3.9 mm; lead pitch 0.635 mm SOT519-1 2001 Dec 12 8 Philips Semiconductors Product data Quadruple FET bus switch CBT3125 TSSOP14: plastic thin shrink small outline package; 14 leads; body width 4.4 mm SOT402-1 2001 Dec 12 9 Philips Semiconductors Product data Quadruple FET bus switch CBT3125 Data sheet status Data sheet status [1] Objective data Preliminary data Product status [2] Development Qualification Definitions This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Changes will be communicated according to the Customer Product/Process Change Notification (CPCN) procedure SNW-SQ-650A. Product data Production [1] Please consult the most recently issued data sheet before initiating or completing a design. [2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Contact information For additional information please visit http://www.semiconductors.philips.com. Fax: +31 40 27 24825 © Koninklijke Philips Electronics N.V. 2001 All rights reserved. Printed in U.S.A. Date of release: 12-01 For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. Document order number: 9397 750 09218 Philips Semiconductors 2001 Dec 12 10