LP064V1

SPECIFICATIONS LP064V1 LIQUID CRYSTAL DISPLAY TITLE: LP064V1 REV. 1 PAGE 1 OF 1 DATA DISPLAY AG LP064V1 6.4“ VGA TFT LCD PRELIMINARY SPECIFICATION T he information given in this document is carefully checked and believed to be reliable. Data Display reserves the right to make changes in product or specification at any time and without further notice. Data Display products are not intended for use in systems in which failures of product could result in personal injury. All mentioned trademarks are registered trademarks of their owner. LG.Philips LCD: Rev. 1, Feb. 10, 1998 DATA DISPLAY AG Industriestrasse 1 D-82110 Germering MAY 2001 http://www.datadisplay.de Tel.: +49-89-894450-0 Fax: +49-89-894450-90 SPECIFICATIONS LP064V1 LIQUID CRYSTAL DISPLAY TITLE: LP064V1 REV. 1 PAGE 2 OF 2 1. GENERAL DESCRIPTION T he LG.Philips LCD model LP064V1 LCD is a Color Active Matrix Liquid Crystal Display with an integral Cold Cathode Fluorescent Tube(CCFT) back light system. The matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in the normally white mode. This TFT-LCD has a 6.4 inch diagonally measured active display area with VGA resolution(480 vertical by 640 horizontal pixel array). Each pixel is divided into Red, Green and Blue subpixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color is determined with a 6-bit gray scale signal for each dot, thus, presenting a pallete of more than 262,144 colors. The LP064V1 LCD is intended to support applications where low power consumption, weight and thickness are critical factors and graphic displays are important. In combination with the vertical arrangement of the sub-pixels, the LP064V1 characteristics provide an excellent flat panel display for office automation products such as portable computers and measurement equipment. G[0:5] B[0:5] CLK HSYNC VSYNC DTMG Timing Controller R[0:5] (GVC10029) Column Driver (UP) Raw Driver 640 x RGB x 480 TFT LCD Array Column Driver (DOWN) +5V VSS Power Supply DC/DC +12V VSS INVERTER CN B/L General Display Characteristics The following are general features of model LP064V1 LCD: Active display area: Outsize dimensions: Pixel pitch: Pixel format Color depth: Display operating mode: Surface treatment: 6.4 inches (cm) diagonal 168W x 123H x 9.0D mm Typ. 0.204 mm * 0.204 mm 640 hor. By 480 ver. Pixels RGB stripe arrangement 6-bit transmissive mode, normally white hard coating (2H), anti-glare treatment of the front polarizer DATA DISPLAY AG Industriestrasse 1 D-82110 Germering MAY 2001 http://www.datadisplay.de Tel.: +49-89-894450-0 Fax: +49-89-894450-90 SPECIFICATIONS LP064V1 LIQUID CRYSTAL DISPLAY TITLE: LP064V1 REV. 1 PAGE 3 OF 3 2. MAXIMUM RATINGS T he following are maximum values which, if exceeded, may cause faulty operation or damage to the unit. T able 1: ABSOLUTE MAXIMUM RATINGS Parameter Power Input Voltage Logic Input Voltage Operating Temperature Storage Temperature Note 1: Symbol VDD VL/H TOP TST -0.5 0 0 -20 Values Min. Max. +5.5 VDD+0.5 +50 +60 Vdc Vdc °C °C at 25° at 25° 1 1 Units Notes Note 2: 3. The Relative Humidity must not exceed 80% non-condensing at temperatures of 50° or less. At temperatures greater than 40°, the wet bulb temperature must not exceed 49°. At low temperature the brightness of CCFT drop and the life time of CCFT become to be short. Under no condition should the unit be exposed to corrosive chemicals. ELECTRICAL SPECIFICATIONS T he LP064V1 requires two power inputs. One is employed to power the LCD electronics and to derive the voltages to drive the TFT array and liquid crystal. The second input which powers the backlight CCFT, is typically generated by an inverter. The inverter is an external unit to the LCD. DATA DISPLAY AG Industriestrasse 1 D-82110 Germering MAY 2001 http://www.datadisplay.de Tel.: +49-89-894450-0 Fax: +49-89-894450-90 SPECIFICATIONS LP064V1 LIQUID CRYSTAL DISPLAY TITLE: LP064V1 REV. 1 PAGE 4 OF 4 T able 2: ELECTRICAL CHARACTERISTICS Parameter MODULE: Power Supply Input Voltage Power Supply Input Current Ripple/Noise Logic Input Level, High Logic Input Level, Low Power Consumption BACKLIGHT Backlight Input voltage Backlight Current Lamp Kick-Off Voltage Operating Frequency Life (half brightness time) Note 1: Note 2: Note 3: Symbol Min. VDD IDD VIH VIL P 4.5 0.7VDD Vss Values Typ. 5.0 180 0.9 Max. 5.5 280 60 VDD 0.3VDD 1.54 Vdc mA mV Vdc Vdc W Units Notes 1 2 2 1 VBL IBL FBL 3.0 35 20.000 355 5.0 55 25.000 385 9.0 680 860 80 VRMS mA VRMS KHz h 3 25 ± 2° 0° The current draw and power consumption specified is for 5.0Vdc at 25° and 25MHz(DCLK). Typical power consumption check pattern is 8 gray scale bar. Logic levels are specified for VDD of 5.0 Vdc at 25°. The values specified apply to all Logic inputs; Hsync, Vsync, clock, data signals, etc. The backlight power consumption shown above does not include loss of external inverter. DATA DISPLAY AG Industriestrasse 1 D-82110 Germering MAY 2001 http://www.datadisplay.de Tel.: +49-89-894450-0 Fax: +49-89-894450-90 SPECIFICATIONS LP064V1 LIQUID CRYSTAL DISPLAY TITLE: LP064V1 REV. 1 PAGE 5 OF 5 4. OPTICAL SPECIFICATIONS Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 30 minutes in a dark environment at 25°. The values specified are at an approximate distance 50 cm from the LCD surface at a viewing angle of Φ and θ equal to 0°. Appendix A presents additional information concerning the specified characteristics. Table 2: OPTICAL CHARACTERISTICS Parameter Contrast Ratio Surface Brightness, white(IBL=5.0mA) Brightness Variation Response Time Rise Time Delay Time CIE Color Coordinates Red Green Blue White Viewing Angle (CR>10:1) x axis, right ( =0º) x axis, left ( =180º) y axis, up ( =90º) y axis, down ( =270º) Note 1: Contrast Ratio (CR) is defined mathematically as: (Surface Brightness with all white pixels) / (Surface Brightness with all black pixels) Note 2: Surface brightness is the center of 5 points(this means number 3 in Appendix A-1 Brightness) across the LCD surface 50 cm from the surface with all pixels displaying white. For more information see Appendix. A. Symbol Min. CR SBWH SBV T rR T rD xR yR xG yG xB yB xW yW 100 Values Typ. 250 150 20 35 0.587 Units Max. 1.4 50 50 0.617 0.382 0.314 0.582 0.174 0.152 0.352 0.349 45 45 20 40 cd/m 2 Notes 1 2 3 4 4 5 5 5 5 5 5 5 5 6 0.557 0.322 0.254 0.522 0.114 0.092 0.292 0.289 msec msec 0.352 0.284 0.552 0.144 0.122 0.322 0.319 degree, ° DATA DISPLAY AG Industriestrasse 1 D-82110 Germering MAY 2001 http://www.datadisplay.de Tel.: +49-89-894450-0 Fax: +49-89-894450-90 SPECIFICATIONS LP064V1 LIQUID CRYSTAL DISPLAY TITLE: LP064V1 REV. 1 PAGE 6 OF 6 Note 3: Note 4: Note 5: Note 6: The Variation in surface brightness, SBV is determined by measuring BON at each test position 1 through 5, and then dividing the maximum BON by the minimum BON. Maximum (BON1, BON2, ....BON5) / Minimum (BON1, BON2, ....BON5) Response time is the time required for the display to transition from white to black(Rise Time, TrR) and from black to white (Delay Time, TrD). For additional information see Appendix A. Color Coordinates is unfixed Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are etermined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For more information see Appendix A. DATA DISPLAY AG Industriestrasse 1 D-82110 Germering MAY 2001 http://www.datadisplay.de Tel.: +49-89-894450-0 Fax: +49-89-894450-90 SPECIFICATIONS LP064V1 LIQUID CRYSTAL DISPLAY TITLE: LP064V1 REV. 1 PAGE 7 OF 7 5. INTERFACE CONNECTIONS T his LCD employs two interface connections, a 31 pin connector is used for the module and a three pin connector is used for the integral backlight system. The electric interface connector is model DF9B-31P-1V, manufactured by Hirose. The mating connector part number is DF9-31S-1V or equivalent. The pin configuration for the connector is shown in the table below. Table 3: MODULE CONNECTOR PIN CONFIGURATION Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Symbol Vss CLK Hsync Vsync Vss R0 R1 R2 R3 R4 R5 Vss G0 G1 G2 G3 G4 G5 Vss B0 B1 B2 B3 B4 B5 Vss DTMG Vdd Vdd OAS NC Description Ground Main clock Horizontal sync. Vertical sync. Ground Red data Red data Red data Red data Red data Red data Ground Green data Green data Green data Green data Green data Green data Ground Blue data Blue data Blue data Blue data Blue data Blue data Ground Data Timing Signal Power(+5V) Power(+5V) O/A, A/V Selection No Connection Notes Connect to Vss, see Note 1 Connect to Vss, see Note 1 Red data least significant bit(LSB) Red data most significant bit(MSB) Connect to Vss, see Note 1 Green data least significant bit(LSB) Green data most significant bit(MSB) Connect to Vss, see Note 1 Blue data least significant bit(LSB) Blue data most significant bit(MSB) Connect to Vdd, see Note 2 Connect to Vdd, see Note 2 see Note3 Note 1: Note 2: Note 3: Note 4: All GND (ground) pins should be connected together and to Vss which should also be connected to the LCD’s metal frame. All VDD (power input) pins should be connected together. This pin is Logic input pin and is connected VDD (power input) with surge protection circuit. DTMG, HSYNC and VSYNC shall be supplied simultaneously. DATA DISPLAY AG Industriestrasse 1 D-82110 Germering MAY 2001 http://www.datadisplay.de Tel.: +49-89-894450-0 Fax: +49-89-894450-90 SPECIFICATIONS LP064V1 LIQUID CRYSTAL DISPLAY TITLE: LP064V1 REV. 1 PAGE 8 OF 8 T he backlight interface connector is a model BHR-03VS-1, manufactured by JST. The mating connector part number is SM02(8.0)B-BHS-1-TB or equivalent. The pin configuration for the connector is shown in the table below. T able 4: BACKLIGHT CONNECTOR PIN CONFIGURATION Pin 1 2 3 Note 1: 6. Symbol HV NC LV Description Lamp power input No connect Ground Notes 1 The input power terminal is colored pink. SIGNAL TIMING SPECIFICATIONS ITEM Period Width-Low Width-High Rise Time Fall Time Duty Hsync Set-up Time Hold Time Period Width-Active Rise/Fall Time Vsync Set-up Time Hold Time Period Width-Active Rise/Fall Time DTMG Set up Time Hold Time Rise/Fall Time Horizental Back Porch Horizental Front Porch Vertical Back Porch Vertical Front Porch DATA Set up Time Hold Time Rise/Fall Time DCLK Symbol fCLK tWCL tWCH trCLK tfCLK D tSH tHH tHP tWH tHr,tHf tSV tHV tVP tWV tVr,tVf tSI tHI tIr,tIf tHBP tHFP tVBP tVFP tSD tHD tDr,tDf Min. 7 7 7 7 0.45 3 8 776 12 0 2 515 1 3 8 7 14 Value Typ. (25.18) 0.5 (800) (96) (525) 2 48 16 32 11 Units Max. 28 0.55 880 200 30 560 34 50 30 25 Mhz ns ns ns ns ns ns tCLK tCLK ns tCLK tCLK tHP tHP ns ns ns ns tCLK tCLK tHP tHP ns ns ns Notes D=tCLKL/tCLK for DCLK for Hsync for DCLK for DCLK * Setup, Hold, Rise and Fall Times are TBD. DATA DISPLAY AG Industriestrasse 1 D-82110 Germering MAY 2001 http://www.datadisplay.de Tel.: +49-89-894450-0 Fax: +49-89-894450-90 SPECIFICATIONS LP064V1 LIQUID CRYSTAL DISPLAY TITLE: LP064V1 REV. 1 PAGE 9 OF 9 7. SIGNAL TIMING WAVE FORMS ( DATA : Latched at Fall edge of DCLK ) tHr, tVr t Ir, tDr DCLK tCLKL DATA tCLK Invalid Data tHf, tVf tIf, tDf VrHmin. VrLmax. Hsync, Vsync, DTMG, DATA tWCH tWCL Invalid Data tfCLK trCLK DTMG DCLK Hsync Vsync tHD tSD tHI tSI Hsync DTMG Vsync tSV DTMG tHP tW tHBP tHfP tHH tSH tHV tVP tWV tVBP tVfP SPECIFICATIONS LP064V1 LIQUID CRYSTAL DISPLAY TITLE: LP064V1 REV. 1 PAGE 10 OF 10 8. COLOR INPUT DATA REFERENCE T he brightness of each primary color(red, green and blue) is based on the 6-bit gray scale data input for the color; the higher the binary input, the brighter the color. The table below provides a reference for color versus data input. T able 5: COLOR DATA REFERENCE Color Input Color Data Red Green R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 : : : : : 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 : : : : : 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Blue G0 B5 B4 B3 B2 B1 B0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 : 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 1 0 0 ; : : : : : 0 1 1 1 1 0 1 0 1 1 1 1 1 0 0 1 1 1 1 1 1 R5 Black 0 Red (63) 1 Green (63) 0 Basic Blue (63) 0 Colors Cyan 0 Magenta 1 Yellow 1 White 1 Red (00) Black 0 Red (01) 0 Red (02) 0 Red : Red (61) 1 Red (62) 1 Red (63) 1 Green(00) Black 0 Green (01) 0 Green (02) 0 Green 0 Green (61) 0 Green (62) 0 Green (63) 0 Blue (00) Black 0 Blue (01) 0 Blue (02) 0 Blue 0 Blue (61) 0 Blue (62) 0 Blue (63) 0 DATA DISPLAY AG Industriestrasse 1 D-82110 Germering DEZ 1999 http://www.datadisplay.de Tel.: +49-89-894450-0 Fax: +49-89-894450-90 SPECIFICATIONS LP064V1 LIQUID CRYSTAL DISPLAY TITLE: LP064V1 REV. 1 PAGE 11 OF 11 9. POWER SEQUENCE 4.5V POWER SUPPLY for LOGIC VDD 0.7V t1 4.5V t4 t2 INTERFACE SIGNAL Vi DATA VALID t5 CCFL INVERTER INPUT POWER POWER SEQUENCE t1≤40msec, 0