NE5019N

Philips Semiconductors Linear Products Product specification 8-Bit µp-compatible D/A converter NE/SE5018/5019 DESCRIPTION The NE/SE5018/19 is a complete 8-bit digital-to-analog converter subsystem on one monolithic chip. The data inputs have input latches which are controlled by a latch enable pin. The data and latch enable inputs are ultra-low loading for easy interfacing with all logic systems. The latches appear transparent when the LE input is in the low state. When LE goes high, the input data present at the moment of transition is latched and retained until LE again goes low. This feature allows easy compatibility with most microprocessors. The chip also comprises a stable voltage reference (5V nominal) and high slew rate buffer amplifier. The voltage reference may be externally trimmed with a potentiometer for easy adjustment of full-scale while maintaining a low temperature coefficient. The output of the buffer amplifier may be offset so as to provide bipolar as well as unipolar operation. PIN CONFIGURATIONS F, N Packages DIGITAL GND 1 DB0(LSB) 2 DB1 3 DB2 4 DB3 5 DB4 6 DB5 7 DB6 8 DB7(MSB) 9 LE 10 NC 11 22 ANALOG GND 21 AMP COMP 20 SUM MODE 19 V CC+ 18 V 17 VCC– 16 DAC COMP 15 BIPOLAR OFFSET R 14 V REFIN 13 V OUT OUT REF 12 V REFADJ D Package1 FEATURES • 8-bit resolution • Input latches • Low-loading data inputs • On-chip voltage reference • Output buffer amplifier • Accurate to ± LSB (0.19%) • Monotonic to 8 bits • Amplifier and reference both short-circuit protected • Compatible with 8085, 6800 and many other µPs APPLICATIONS DIGITAL GND 1 DB0(LSB) 2 DB1 3 DB2 4 DB3 5 DB4 6 DB5 7 DB6 8 DB7(MSB) 9 NC 10 LE 11 VREFADJ 12 NOTE: 1. SOL and non-standard pinout 24 ANALOG GND 23 AMP COMP 22 SUM MODE 21 V CC+ 20 V OUT 19 NC 18 V CC– 17 DAC COMP 16 BIPOLAR OFFSET 15 NC 14 V REFIN 13 VREFOUT • Precision 8-bit D/A converters • A/D converters • Programmable power supplies • Test equipment • Measuring instruments • Analog-digital multiplication ORDERING INFORMATION DESCRIPTION 22-Pin Ceramic Dual In-Line Package (CERDIP) 22-Pin Ceramic Dual In-Line Package (CERDIP) 22-Pin Plastic Dual In-Line Package (DIP) 22-Pin Plastic Dual In-Line Package (DIP) 24-Pin Small Outline Large (SOL) Package TEMPERATURE RANGE 0 to +70°C -55°C to +125°C 0 to +70°C -55°C to +125°C 0 to +70°C ORDER CODE NE5018/5019F SE5018/5019F NE5018/5019N SE5018/5019N NE5018/5019D DWG # 0585B 0585B 0409B 0409B 0173D August 31, 1994 751 853-0845 13721 Philips Semiconductors Linear Products Product specification 8-Bit µp-compatible D/A converter NE/SE5018/5019 BLOCK DIAGRAM (19) VCC+ VREF (13) OUT VREF (12) ADJ 5k 5k 15k (10) LE (1) (9) (8) (7) (6) (5) (4) (3) (2) DIGITAL DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 GND MSB LSB LATCHES AND SWITCH DRIVERS (20) SUM NODE (18) VOUT + – 5k DAC CURRENT OUTPUT + – INT VREF AMP (21) COMP (22) ANALOG GND DAC SWITCHES (14) VREF IN 5k (15) BIPOLAR OFFSET 5k + – DAC (16) COMP VCC– (17) ABSOLUTE MAXIMUM RATINGS SYMBOL VCC+ VCCVIN VREF IN VREF ADJ VSUM IREF SC IOUTSC PD Positive supply voltage Negative supply voltage Logic input voltage Voltage at VREF input Voltage at VREF adjust Voltage at sum node Short-circuit current to ground at VREF OUT Short-circuit current to ground or either supply at VOUT Maximum power dissipation, TA=25°C F package N package D package TA Operating temperature range SE5018 NE5018 TSTG TSOLD Storage temperature range Lead soldering temperature (10 seconds) NOTES: 1. Derate above 25°C at the following rates: F package at 13.9mW/°C N package at 17.5mW/°C D package at 12.8mW/°C 300 °C -55 to +125 0 to +70 -65 to +150 °C °C °C (still-air)1 1740 2190 1600 mW mW mW PARAMETER RATING 18 -18 0 to 18 12 0 to VREF 12 Continuous Continuous UNIT V V V V V V August 31, 1994 752 Philips Semiconductors Linear Products Product specification 8-Bit µp-compatible D/A converter NE/SE5018/5019 DC ELECTRICAL CHARACTERISTICS VCC+=+15V, VCC-=-15V, SE5018. -55°C≤TA≤125°C, NE5018. 0°C≤TA≤70°C, unless otherwise specified. 1 Typical values are specified at 25°C. SYMBOL PARAMETER Resolution Monotonicity Relative accuracy VCC+ VCCVIN(1) VIN(0) IIN(1) IIN(0) VFS Positive supply voltage Negative supply voltage Logic “1” input voltage Logic “0” input voltage Logic “1” input current Logic “0” input current Full-scale output Pin 1=0V Pin 1=0V Pin 1=0V, 2V