1002292

https://www.phoenixcontact.com/pi/products/1002292 Accessories - PRC FC RELEASE LATCH GY - 1002292 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) Color-coding, Range of articles: PRC 35, Accessories, housing material: PA 6.6-FR. If you are using the release latch, then the PRC approvals in accordance with IEC 61535 and 2PfG 1915 are not required Product Description Manual release latch for PRC-HR variants Your advantages  Convenient release of PRC connectors by hand, no tools required  Coloring enables quick assignment to the mating connector  Color coding for PRC connectors  Easy installation  Other colors available on request Key Commercial Data Packing unit 50 pc Minimum order quantity 50 pc GTIN GTIN 4055626463667 Weight per Piece (excluding packing) 0.335 g Weight per piece (including packing) 0.336 g Custom tariff number 39269097 Country of origin Germany Note Made to Order (non-returnable) Technical data General data Width 16 mm Height 8.9 mm Length 8.8 mm 06/20/2021   Page 1 / 3 https://www.phoenixcontact.com/pi/products/1002292 Accessories - PRC FC RELEASE LATCH GY - 1002292 Technical data Connection data Color gray GY Material data Material of grip body PA Housing material PA 6.6-FR Ambient conditions Ambient temperature (operation) 105 °C Standards and Regulations Safety note • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible. • WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product. WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property. • Assembled products may not be manipulated or improperly opened. • Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products). • When using the product in direct connection with third-party manufacturers, the user is responsible. • For operating voltages > 50 V AC, conductive connector housings must be grounded • Ensure that the protective or functional ground has been properly connected. • VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector • Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product • Only use tools recommended by Phoenix Contact • The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product. • Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products • Operate the connector only when it is fully plugged in. • Operate the connector only when it is fully plugged in and interlocked. • Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards. 06/20/2021   Page 2 / 3 https://www.phoenixcontact.com/pi/products/1002292 Accessories - PRC FC RELEASE LATCH GY - 1002292 Technical data Standards and Regulations • Observe the minimum bending radius of the cable. Lay the cable without twisting it. • The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12). Environmental Product Compliance China RoHS Environmentally friendly use period: unlimited = EFUP-e No hazardous substances above threshold values Classifications eCl@ss eCl@ss 10.0.1 27440109 eCl@ss 11.0 27440109 eCl@ss 9.0 27440103 ETIM ETIM 6.0 EC002061 Phoenix Contact 2021 © - all rights reserved http://www.phoenixcontact.com 06/20/2021   Page 3 / 3