PLC ACCESSORIES
Accessories for the PLC INTERFACE Series
Data Sheet
103153_00_en
m
INTERFACE
© PHOENIX CONTACT - 02/2007
Description
co
500 mm long FBST 500 continuous plug-in bridges can be
used to bridge up to 80 modules quickly and easily at a time.
s.
PLC-ATP Insulating Plate
The PLC-ATP insulating plate should always be installed at
the start and end of every terminal strip.
In addition to the visual separation of function blocks, it is
also necessary in some cases to install the insulating plate
between adjacent PLC INTERFACE modules, e.g., when
three phases (L1, L2, L3) are used on the contact side of the
PLC INTERFACE modules.
ne
The 9 mm PLC-ESK GY power terminal block is the same
shape as the PLC INTERFACE modules. It is used to
supply the bridging potentials. Its nominal current is 32 A.
For currents ≤ 6 A, the power can be supplied directly at the
connection terminal blocks of one of the connected PLC
INTERFACE modules.
nt
PLC-ESK Power Terminal Block
po
FBST Plug-In Bridges
in
ec
om
The colored, insulated FBST plug-in bridges reduce wiring
time for the PLC INTERFACE modules by up to 70% in
comparison with conventionally wired relay modules. 2-pos.
FBST 6 single plug-in bridges are ideal for bridging a
smaller number of modules and total currents ≤ 6 A. For a
circuit supplied from both sides, they offer the advantage
that the circuit can be opened at any point, while allowing all
the other modules to continue being supplied at the same
time.
on
l
If a PLC-ATP insulating plate is to be bypassed with single
plug-in bridges, the FBST 8 2-pos. plug-in bridge must be
used.
The FBST 14 2-pos. plug-in bridge connects adjacent
connections on a 14 mm PLC INTERFACE module. In this
way, contacts can be connected in series or in parallel
without additional wiring.
PLC-ATP has prescored break-out points at the bridging
positions, so that individual bridges can be passed through
if necessary.
PLC-BP Feed-Through Bridge
Instead of a relay or solid-state relay, the PLC-BP (A1-14)
passive feed-through bridge can be inserted in the basic
terminal block of the PLC INTERFACE series. This enables
a passive connection to be established between terminal
points A1 and 14.
PLC-V8 Adapter
The PLC-V8 adapter can be used to connect both 6.2 mm
and 14 mm PLC INTERFACE modules quickly and easily to
the VARIOFACE system cabling (see INTERFACE
catalog).
Make sure you always use the latest documentation.
It can be downloaded at www.download.phoenixcontact.com.
A conversion table is available on the Internet at
www.download.phoenixcontact.com/general/7000_en_00.pdf.
This data sheet is valid for all products listed on the following page:
PLC ACCESSORIES
ZB 6 Zack Marker Strip
conveniently split at any point. They are available with
horizontal and vertical labeling (see CLIPLINE catalog).
The ZB marker system provides logical and clear
identification of the modular terminal blocks and
INTERFACE modules. Multipartite ZB strips can be
Other pitches and labels are available on request.
Unprinted ZB strips can be labeled individually using a
plotter or by hand.
Ordering Data
Zack Marker Strip
Description
Type
Order No.
Pcs./Pck.
10-section, for individual labeling with TML (EX9,5)R TR, X-PEN or CMS-P1
PLOTTER, each pack provides enough strips to label
100 PLC INTERFACE modules
ZB 6: UNBEDRUCKT
1051003
10
As above, but large pack; each pack provides enough strips to label
1000 PLC INTERFACE modules
ZB 6/WH-100: UNBEDRUCKT
5060935
100
ZB 6, LGS: FORTL. ZAHLEN
1051032
10
1051126
10
1051032
10
L1, L2, L3, N, PE, L1, L2, L3, N, PE ZB 6, LGS: L1-N, PE
1051414
10
U, V, W, N, 6, U, V, W, N, 6 ZB 6, LGS: U-N
1051430
10
1051029
10
1051045
10
ZB 6, QR: SPS EINGANG...2
1051456
10
ZB 6, QR: SPS AUSGANG...2
1051443
10
ZB 6: SO/CMS...3
1050499
1
co
m
Zack marker strip, unprinted:
Zack marker strip, printed horizontally:1
s.
1 - 10 ZB 6, LGS: 1-10
10-section, with consecutive numbers
11 - 20 ZB 6, LGS: 11-20
nt
... ...
991 - 1000 ZB 6, LGS: 991-1000
Zack marker strip, printed horizontally:1
1 - 9 ZB 6, LGS: 1-9
ne
9-section, with numbers 1 - 9
Zack marker strip, printed horizontally:1
ZB 6, LGS: GLEICHE ZAHLEN
10-section, with identical numbers
1/1/1 ZB 6, LGS: 1
po
2/2/2 ZB 6, LGS: 2
... ...
100/100/100 ZB 6, LGS: 100
om
Zack marker strip, printed horizontally:1
10-section
Zack marker strip, printed vertically:1
1 - 10 ZB 6, QR:
... ...
991 - 1000 ZB 6, QR: 991-1000
Zack marker strip, printed vertically:1
ZB 6, QR: GLEICHE ZAHLEN
10-section, with identical numbers
on
l
1-10
11 - 20 ZB 6, QR: 11-20
in
ec
10-section, with consecutive numbers
ZB 6, QR: FORTL. ZAHLEN
1/1/1 ZB 6, QR: 1
2/2/2 ZB 6, QR: 2
... ...
100/100/100 ZB 6, QR: 100
Zack marker strip, printed vertically:1
10-section, with PLC input numbers, e.g., I 0.0 to I 0.7 (up to I 127.7, maximum)
Zack marker strip, printed vertically:1
10-section, with PLC output numbers e.g., O 0.0 to O 0.7 (up to O 127.7, maximum)
Zack marker strip with special labeling:
10-section, can be separated, labeled according to customer requirements
10
1
Ten identically labeled strips make up one unit pack (Pcs./Pck.).
2
Specify desired labeling when placing an order.
3
Specify desired labeling and color when placing an order.
103153_00_en
10
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
Vertical labeling (QR):
1
Horizontal labeling (LGS):
PHOENIX CONTACT
2
PLC ACCESSORIES
Power Terminal Block
Description
Type
Power terminal block, to supply up to four potentials,
same shape as the PLC INTERFACE series
Gray PLC ESK GY
Plug-In Bridges
Description
Type
Plug-in bridge, 2-pos., 6 mm long, insulated, for potential
distribution with PLC..., Imax = 6 A
Pcs./Pck.
5
Order No.
Pcs./Pck.
Red FBST 500-PLC RD
2966786
20
Blue FBST 500-PLC BU
2966692
20
Gray FBST 500-PLC GY
2966838
20
Red FBST 6-PLC RD
2966236
50
Blue FBST 6-PLC BU
2966812
50
m
Continuous plug-in bridge, 500 mm long, insulated,
can be cut to any length, for potential distribution with
PLC..., Imax = 32 A
Order No.
2966508
Gray FBST 8-PLC GY
Plug-in bridge, 2-pos., 14 mm long, insulated, for potential
distribution
Black FBST 14-PLC BK
Insulating Plate
Description
nt
Type
50
2967688
50
PLC ATP BK
2967691
50
Order No.
Pcs./Pck.
2966841
25
Order No.
Pcs./Pck.
2980283
1
Feed-Through Bridge
Description
Type
in
ec
om
Passive feed-through bridge, can be inserted instead of a
relay or solid-state relay, bridges terminal points A1 and 14
Screwdriver
Description
po
ne
Insulating plate, 2 mm thick, to be installed at the start and end of every PLC
terminal strip. For the visual separation of groups, safe isolation of different
voltages from adjacent PLC INTERFACE modules according to
DIN EN 50178/VDE 0160, isolation of adjacent bridges with different
potentials, isolation of PLC INTERFACE modules for voltages greater than
250 V. Color: black
s.
Plug-in bridge, 2-pos., 8 mm long, insulated, for potential
distribution with insulating plate
2966825
co
Gray FBST 6-PLC GY
Bladed type screwdriver, blade: 0.6 x 3.5 x 100 mm, length 180 mm
on
l
Technical Data
Black PLC BP (A1-A14)
Type
Order No.
Pcs./Pck.
SZF 1-0,6X3,5
1204517
10
PLC-ESK Power Terminal Block
Nominal input voltage1
Total current
Connection type
250 V AC, maximum
32 A, maximum
Screw connection
Conductor cross section (solid and stranded)
0.2 mm2 ... 4 mm2
Stripping length
10 mm
Dimensions (W x H x D)
9 mm x 94 mm x 80 mm
Housing material
Polyamide PA, color: gray
1
The PLC-ATP BK insulating plate must be installed for voltages greater than 250 V (L1, L2, L3) between the same terminal points on adjacent modules
(see "Insulating Plate"). FBST 8-PLC... or FBST 500... is then used for potential bridging.
© PHOENIX CONTACT 02/2007
103153_00_en
PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany
Phone: +49 - 52 35 - 30 0 • Fax: +49 - 52 35 - 34 12 00
www.phoenixcontact.com
3
